Tender For General-Ssf-Okkal-2026-Maintenance Of Farm Store Room And Godown -General Civil Work
Tender Value
16.94 Lakhs
Estimated cost
Bid Submission
04 Aug 2026
3 days left
EMD
42367
Bank guarantee accepted
Document Fee
2760
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Ernakulam → Kerala
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for General-Ssf-Okkal-2026-Maintenance Of Farm Store Room And Godown -General Civil Work
BOQ
| Sl. No. | Item Description |
| 1 | Repair of Godown 2 Nos |
| 2 | 15.12.1:Dismantling doors, windows and clerestory windows (steel or wood ) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead:Of area 3 sq. metres and below |
| 3 | OD672/2026-2027:Modified 15.26 Demolishing and removing the existing wooden planks laid in the godown floor, including stacking of serviceable materials and disposal of unserviceable materials within a lead of 50 metres, complete as directed by the Engineer-in-Charge. |
| 4 | OD675/2026-2027:Modified 22.1.1"Providing anti-rodent and pest control treatment to floor surfaces and wall-floor junctions by drilling holes in the floor at approximately 1.0 m centre-to-centre intervals and injecting/pouring approved anti-termite/pest control chemical emulsion in the specified quantity, including sealing of drilled holes after treatment, application of approved chemicals, rodent repellents, baiting agents and other control measures, complete as per manufacturer's specifications and directions of the Engineer-in-Charge." |
| 5 | 4.1.3:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand (zone-III)derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 6 | 50.13.1:9 mm cement plastering of mix : 1:3 (1 cement : 3 fine sand ) including all cost of materials, labour charges etc complete |
| 7 | OD668/2026-2027:Modified 50.9.11.2 Providing and fixing 18 mm thick Thomson Multi Wood Board or approved equivalent make paneling to the existing frame, backing or studding, including cutting the board with a router machine to provide a 5 cm overlap on all four sides, and securing it with screws, fisher fasteners and all necessary accessories. The work shall include all materials, labour, cutting, fitting, alignment and finishing required for the proper completion of the paneling. The cost of frames, backing or studding shall be measured and paid for separately. The work shall be carried out complete in all respects as directed by the Site Engineer-in-Charge. |
| 8 | OD671/2026-2027:Modified 50.9.11.1 Providing and fixing 12 mm thick Thomson Multi Wood Board or approved equivalent make paneling to the existing frame, backing or studding, including cutting the board with a router machine to provide a 5 cm overlap on all four sides, and securing it with screws, fisher fasteners and all necessary accessories. The work shall include all materials, labour, cutting, fitting, alignment and finishing required for the proper completion of the paneling. The cost of frames, backing or studding shall be measured and paid for separately. The work shall be carried out complete in all respects as directed by the Site Engineer-in-Charge. |
| 9 | OD674/2026-2027:Modified 14.85 "Taking out existing wooden door shutter, repairing the shutter by cutting, fitting, painting and other necessary works, and refixing the repaired door shutter to the existing door frame, including replacement of hinges with screws wherever required. The item shall also include providing and nailing/fixing aluminium sheet on one side of the door shutter up to a height of 50 cm from the bottom for protection against rodents, complete in all respects and as directed by the Engineer-in-Charge." |
| 10 | 13.61.1:Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:Two or more coats on new work |
| 11 | 13.99.1:Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :One or more coats on old work |
| 12 | OD785/2026-2027:Modi 13.99.1 Providing labour for scraping, wire brushing, grinding, cleaning and surface preparation of existing M.S. angles, flats and other steel members, removing all loose rust, old paint, scales, dirt and foreign materials, including levelling and smoothing of surfaces wherever required, preparing the steel surface ready for application of primer and paint, complete with all labour, tools, tackles and disposal of debris. |
| 13 | 13.109.1:Finishing walls with water proofing cement paint of required shade :Old work (one or more coats applied @ 2.20 kg/10 sqm) over priming coat of primer applied @ 0.80 litrs/10 sqm complete including cost of Priming coat. |
| 14 | 50.9.1.1:Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately), using good quality Anjili wood /jack wood |
| 15 | 21.1.2.2:For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately)Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 16 | 21.3.1:Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm) |
| 17 | OD741/2026-2027:Modified 15.28.1 Dismantling old false ceiling of any type including ceiling tiles/boards, supporting framework, hangers, perimeter channels, fixtures and fittings wherever required, complete. The dismantled materials shall be carefully removed and stacked within 50 metres lead as directed by the Engineer-in-Charge. |
| 18 | 21.5:Providing and fixing powder coated aluminium work ( minimum thickness of powder coating 50 micron) consisting of tee /angle sections, of approved make conforming to IS : 733 in frames of false ceiling including aluminium angle cleats with necessary C.P brass/ stainless steel sunk screws, aluminium perimeter angles fixed to wall with stainless steel rawl plugs @ 450 mm centre to centre and fixing the frame work to G.I level adjusting hangers 6 mm dia. with necessary cadmium plated machine screws all complete as per approved architectural drawings and direction of the Engineer-in-Charge ( level adjusting hangers, ceiling cleats and expansion hold fasteners to be paid for separately ). |
| 19 | 50.12.4.2:Providing and fixing false ceiling with 7.5 mm thick PVC wooden grains panel board ceiling of approved quality in aluminium frame work with necessary screws etc complete ( aluminium frame work shall be paid separately) |
| 20 | 11.41A.3.2: Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.Glazed Vitrified tiles Matt/Antiskid finish of size Size of Tile 600 x 1200 mm |
| 21 | 11.47.2:Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS : 15622, of approved brand & manufacturer,in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately).Size of Tile 600x600 mm |
| 22 | 10.29.1:Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15x3 mm and nuts & bolts complete.Galvanised M.S. Wire gauze with 0.63 mm dia wire and 1.4 mm aperture on both sides |
| 23 | 12.50:Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+0.05%), total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 24 | 12.51.1:Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screwscomplete :Ridges plain (500-600 mm) |
| 25 | 50.10.2:Steel work for purlin/single section with G I pipes including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete |
| 26 | 15.28.2:Dismantling roofing including ridges, hips, velleys and gutters etc., and stacking the material within 50 metres lead of :Asbestos cement Sheet |
| 27 | OD786/2026-2027:Modi 15.28.2 Dismantling the existing asbestos cement (A.C.) sheet roofing, including ridges, hips, valleys, gutters and other roofing accessories at the Seed Store House near the Farm Office, carefully removing and stacking the dismantled materials within 50 metres lead. Re-fixing the available serviceable asbestos cement sheets on the roof, including alignment, replacement of damaged hooks, J-bolts, nuts, washers and other fixing accessories wherever required, sealing of laps, joints and fixing points with approved weatherproof sealant, making good all defects and ensuring that roof leakages are completely arrested and the roofing is made watertight, including all labour, materials, tools, tackles, scaffolding and incidental charges, complete as directed by the Engineer-in-Charge. |
| 28 | OD787/2026-2027:Modified 12.51.6 Providing and fixing ISI quality uPVC square type rain water gutter of size 100–150 mm (4"–6") width and 125–150 mm (5"–6") depth, manufactured from high-quality UV resistant uPVC material, including all necessary fittings such as brackets every 1 m, couplers, end caps, outlets, bends, clamps and fasteners. The gutter shall be fixed at the required slope to ensure free flow of rainwater and connected to the existing/proposed rain water down-take pipes. The work includes cutting, jointing, sealing of joints, testing for leakages and making the complete rainwater disposal system watertight, including all labour, materials, tools, tackles and incidental charges, complete as directed by the Engineer-in-Charge. |
| 29 | 50.18.9.18.2:Providing and fixing PVC pipes including fixing the pipe with clamps/Clips at 1.00 m spacing. This included jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 75 mm dia 4 Kfg/cm2 - External work - Exposed on wall Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 28, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 04, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 3 daysAug 06, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 5 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender