Tender For Provision Of Bathroom And Toilet In Bldg No P-389 Under Ge (South) Ambala Cantt
Tender Value
9.57 Lakhs
Estimated cost
Bid Submission
18 Aug 2026
17 days left
EMD
19150
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Ambala → Haryana
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Provision Of Bathroom And Toilet In Bldg No P-389 Under Ge (South) Ambala Cantt
BOQ
| Sl. No. | Item Description |
| 1 | [B&R PORTION]Surface excavation not exceeding 30cm deep and averaging 15cm deep in soft/losse soil including removal of vegetation, bushes, shrubs and trees(not exceeding 30cm in girth) complete all as specified and directed by Engineer-in-Charge. |
| 2 | Excavating in trenches, not exc 1.5 m wide and not exc 1.5 m in depth; for foundation, etc. Or for shafts, wells, cesspits, manholes, pier holes, etc. not exc 10 sq m on plan not and getting out in Soft /loose any type of soil complete all as specified and directed by Engr -in -Charge |
| 3 | Material and labour for plain cement concrete 1:4:8 type D2 (using 40 mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified and directed by Engr -in -Charge |
| 4 | Material and labour Reinforced cement concrete 1:2:4 Type B1 (using 20mm graded mechanically crushed stone aggregate) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete, complete all as specified and directed by Engr -in -Charge |
| 5 | Material and labour for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) for rough finished flat surfaces of concrete complete all as specified and directed by Engr -in -Charge |
| 6 | Material and labour for formwork to edges of concrete flats, treads, breaks in floors,window cills, concrete railings, openings in concrete walls, floor and roofs not exceeding 20cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exceeding 10cm but not exceeding 20cm wide for fair finished surfaces of concrete complete all as specified and directed by Engr -in -Charge. |
| 7 | Material and labour for RCC 1:2:4 type B1 (using 20mm graded mechanically crushed stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed by Engr -in -Charge |
| 8 | Material and labour for RCC type B 1, 1:2:4 (using 20mm graded mechanically crushed stone aggregate) as in columns, pillars, piers,posts and struts complete all as specified and directed by Engr -in -Charge |
| 9 | Material and labour for RCC type B 1, 1:2:4 (using 20mm graded mechanically crushed stone aggregate) as in beams, cantilevers,bressummers, lintels over 1.5mtr span complete all as specified and directed by Engineer-in-Charge. |
| 10 | Material and labour for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for fair finished flat surfaces of concrete complete all as specified and directed by Engineer-in-Charge. |
| 11 | Material and labour for formwork to sides of pillars, posts, struts, piers, columns and stanchions for fair finished flat surfaces of concrete complete all as specified and directed by Engineer-in-Charge. |
| 12 | Material and labour for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. for rough finished flat surfaces of concrete complete all as specified and directed by Engineer-in-Charge. |
| 13 | Material and labour for mild steel TMT bars 10mm dia and over, Fe 500/Fe 500D grade conforming to IS-1786, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips as in main reinforcement complete all as specified and directed by Engineer-in-Charge. |
| 14 | Material and labour for mild steel TMT bars 6mm to 8mm dia, , Fe500/Fe500D grade confirming to IS-1786, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips as in stirrups, spacer and binders complete all as specified and directed by Engr -in -Charge |
| 15 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm in soft/loose soil complete all as specified and directed by Engr -in -Charge |
| 16 | Removing excavated material exc 250 m but not exc 500m and depositing where directed at a level not exc 1.5 m high, complete all as specified by Engr-in-Charge |
| 17 | Material and labour for laying broken stone or boulders hardcore of guage exc 63 mm but not exc 100 mm deposited spread and levelled in layers not exc 15 cm thick watered rolled/rammed to a true surface complete all as specified and directed |
| 18 | Material and labour for, 75 mm thick Plain Cement Concrete, Type D2 1:4:8, (using 40 mm graded stone aggregates), as in sub base complete all as specified and directed by Engineer-in-Charge. |
| 19 | Material and labour for plain cement concrete 25mm thick 1:2:4 type B-1 (using 20mm graded aggregate) as in leveling course/sub base complete all as specified and directed by Engr-in charge |
| 20 | Material and labour for 15mm thick screed bed or bedding layer in CM 1:4 for laying floor finish complete all as specified and directed by Engineer-in-Charge. |
| 21 | Material and labour for Non skid ceramic coloured tiles 7 to 8mm thick Suqare/rectangular) area of each tile exceeding 0.06sqm but not exceeding 0.11 sqm in floors etc. set and jointed in neat cement slurry and pointed in white of coloured cement to match, complete all as specified and directed by Engineer-in-Charge. |
| 22 | Material and labour for coloured glazed ceramic tiles 300 x450x 7mm thick, on vertical surfaces such as skirting, dados and risers to steps etc set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match the shade of tiles over 10mm screed in CM 1:4, complete all as specified and directed by Engineer-in-Charge. |
| 23 | Supply and fixing Chequered cement concrete commercial Tiles 25cm x 25cm x 20 to 22mm /30cmx30cmx20 to 25mm thick with grey cement and pigment set jointed and pointed in neat cement slurry in floors and cut and polished laid over and including 15mm thick Screed in CM 1:6 complete all as specified and as directed. |
| 24 | Material and labour for 75mm thick PCC 1:3:6 type C-1 (using 20mm graded crushed stone aggregate) as in paving/plinth protection/ laid in panels and joints filled with mix of bitumen and sand (1:3) by weight, finished the surface even and fair without using extra cement complete all as specified and directed |
| 25 | Material and labour for plain cement concrete 1:2:4 type B1 (using 20mm graded stone aggregates) as in coping/ bed plate/ bed block including necessary forms and moulds, complete all as specified and directed by Engr -in-Charge |
| 26 | Material and labour for brick work with fly ash bricks straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and directed by the Engr-in-Charge |
| 27 | Material and labour for brick work with fly ash bricks straight or curved on plan to any radius built in half brick thick walls built in cement mortar 1:4 complete all as specified and directed by the Engr-in-Charge |
| 28 | Material and labour for 15mm thick rendering on brick or concrete surface wall on fair face/other than fair face in cement mortar 1:4 with water proofing compound as per manufacturer's instructions and finishing the surface with even and fair without using extra cement complete all as specified and as directed. |
| 29 | Supply only water proof compound ,complete all as specified and directed by the Engr-in-Charge |
| 30 | Material and labour for 5mm thick rendering on ceilings in cement mortar 1:3 and finishing the surface even and smooth without using extra cement all complete as specified and as directed. |
| 31 | Material and labour for preparation of newly plastered or unplastered surfaces and applying three coats of white wash on wall surface complete all as specified and directed by Engineer-in-Charge. |
| 32 | Material and labour for preparation new surface and applying three coat of white wash on ceiling complete all as specified and as directed. |
| 33 | Material and labour for Applying two coats of cement base paint over a coat of primer on new wall surface including preparation of surface complete all as specified and directed by Engineer-in-Charge. |
| 34 | Supply and fixing Pillar tap 15mm dia, cast copper alloy, with capstan heads, chromium plated screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shank and fly nuts, screwed for iron pipe and fixed complete all as specified and as directed. |
| 35 | Supply and fixing Stop valves 15mm dia cast copper alloy, screwed down high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for union complete all as specified and as directed. |
| 36 | Supply and fixing angle valve cast copper alloy chromium plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes of 15mm bore complete all as specified and directed by Engineer-in-Charge. |
| 37 | Supply and fixing 15 mm CP cast copper alloy bib taps fancy type chromium plated screwed down, for iron pipe or for brass ferrule complete all as specified and directed by Engineer-in-Charge. |
| 38 | Supply and fixing 32mm bore High density polyethylene pipes (HDPE) of pressure rating 6kg/sqcm laid in trenches complete all as specified and as directed. |
| 39 | Supply and fixing 75mm PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or floors complete all as specified and as directed. |
| 40 | Supply and fixing, UPVC (SWR) pipes 110 mm dia single socketed in any length with solvent cement joints laid under floor or on walls/trench fixed as soil / waste / vent pipes with Stack clamps made out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall complete all as specified and directed by Engineer-in-Charge. |
| 41 | Supply and fixing 110 mm bore dia PVC (SWR) reducers, complete all as specified and directed by Engineer-in-Charge. |
| 42 | Supply and fixing PVC (SWR) bends any radius, 110mm bore with / without access door, complete all as specified and directed by Engineer-in-Charge. |
| 43 | Supply and fixing new 15 mm bore Galvanized Iron tubing, medium grade, with all fittings, such as Tee, elbows, sockets, unions, short pieces and application of bituminous paint in concealed portion, fixed to wall/ ceiling or laid on floors or trench , complete all as specified and directed by Engineer-in-Charge. |
| 44 | Supply and fixing 20 mm bore Galvanized Iron tubing, medium grade, with all fittings, such as Tee, elbows, sockets, unions, short pieces and application of bituminous paint in concealed portion, fixed to wall/ ceiling or laid on floors, complete all as specified and directed by Engineer-in-Charge. |
| 45 | Material and labour for cast iron floor trap 75mm dia, with grating including jointing to wate pipe fixed in cement concrete type B1 1:2:4 (using 20mm graded stone aggregate) complete all as specified and directed by Engineer-in-Charge. |
| 46 | Material and labour for salt glazed stoneware gully trap, square or round moulded type 'P', 100x100mm size complete all as specified and as directed by Engineer-in-Charge. |
| 47 | Supply and fixing PVC connection 15 mm dia, 450 mm long including check nut complete all as specified and as directed by Engineer-in-Charge. |
| 48 | Material and labour for pre- polished granite slab machine cut of any shade of 15 to 20 mm thick including necessary notching, chamfering the edges over cement screed bed including Cutting, Grinding and Mirror polishing(Granite finish) with suitable grinding stones complete all as specified and as directed by Engineer-in-Charge. |
| 49 | Rounding to edges of stone slabs one edge, such as in steps, cooking platforms, and other similar situations complete all as specified and directed by Engineer-in-Charge. |
| 50 | Supply and fixing vitreous china wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) but including sheet cover and complete all as specified and directed by Engineer-in-Charge. |
| 51 | Supply and fixing Viterous china wash basin, white, flat back, size 630x450mm counter sunk oval type fixed in granite excluding taps, waste,chain and plug and porcelain stopper complete all as specified and directed |
| 52 | Supply and fixing Vitreous China urinals, half stall type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe, complete all as specified and directed by Engineer-in-Charge. |
| 53 | Supply and fixing vitreous china urinal partition ,white of size 310 x 700mm /any size etc complete all as specified and directed by Engineer-in-Charge. |
| 54 | Supply and fixing waste coupling CP brass (half or full threaded) 32 mm dia complete all as specified and directed by Engineer-in-Charge. |
| 55 | Supply and fixing 600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed by Engineer-in-Charge. |
| 56 | Supply only PVC valve less syphonic action type flushing cistern 10 ltr capacity low level, white/coloured with inlet ball valve float and handle including bracket and PVC connection pipes complete all as specified and directed by Engineer-in-Charge. |
| 57 | Supply only flush pipe of polythene of low or high density 32 mm PVC for low level flushing cistern complete all as specified. |
| 58 | Supply and fixing health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connection Supply and fixing in position complete in all respect as specified. |
| 59 | Supply and fixing chromium plated square shape towel ring fixed with chromium plated brass screws in approved pattern complete all as specified and directed by Engineer-in-Charge. |
| 60 | Supply and fixing stainless steel chromium plated toilet paper holder in approved pattern, shape and size completed all as specified and directed. |
| 61 | Supply and fixing fancy type chromium plated brass soap dish suitable for double soap fixed of approved pattern, shape and size complete all as specified and directed by Engineer-in-Charge. |
| 62 | Supply and fixing factory made solid PVC moulded door shutter (with wood free EPS), 28 to 30 mm thick (Stiles) with 2, 4, 6 raised panel design with 2mm thick moulded PVC sheet on the front face and 2mm plain colour PVC sheet on back face and fixing in frame at site as per drawing shown on SSR complete all as specified and directed by Engineer-in-Charge. |
| 63 | Supply and fixing Solid PVC Door Frame of size 50 mm x 47 mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, complete all as per specified and as directed. |
| 64 | Supply and fixing steel ventilator with top hung shutter including hinges peg stay to receive glazing or gauzing and one coat of primer including fixing of hold fast of size 25 x 5 mm of flat iron etc complete all as specified and directed by Engineer-in-Charge. |
| 65 | Supply and fixing butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21, 75 mm long complete all as specified and directed |
| 66 | Supply and fixing 125 mm Extruded Aluminium handles fabricated type anodised etc complete all as specified and directed by Engineer-in-Charge. |
| 67 | Supply and fixing 150 mm long aluminium, anodised barrel tower bolt of extruded section complete all as specified and directed |
| 68 | Supply and fixing 100 mm long aluminium, anodised barrel tower bolt of extruded section complete all as specified and directed |
| 69 | Supply and fixing 3 mm thick figured glass not exc 0.50 sqm each pane and fixed with oil putty or with wooden beading in square etc complete all as specified and directed by Engineer-in-Charge. |
| 70 | Mateial and labour for preparation of new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by Engineer-in-Charge. |
| 71 | Supply and fixing of 500 Litre capacity rotational moulded polythene water storage tanks (cylindrical vertical with closed top) of specifications as per SSR Part – I and hoisted, fixed in position complete all as specified and directed by Engineer-in-Charge. |
| 72 | Supply and fixing Gun metal Gate valves 20 mm dia with iron wheel head, screwed both ends for iron pipe and fixed including cutting / threading old pipes and provision of new fittings such as Tee, socket, elbow, union etc as required, complete all as specified and directed |
| 73 | Supply and fixing of 20 mm bore ball valves, high pressure, PTMT, with polythene float and fly nut complete screwed for iron pipe or brass ferrule complete all as specified and directed by Engineer-in-Charge. |
| 74 | Material and labour for concrete bed to drain pipes including packing under , haunching against RM the sides of pipes after they are laid and tested in cement concrete 1:3:6 for 150 mm dia pipe complete all as specified and directed by Engineer-in-Charge. |
| 75 | Material and labour for 150 mm dia Salt glazed stoneware drain pipes laid in trenches and jointed complete all as specified and directed by Engineer-in-Charge. |
| 76 | Material and labour for Brick work with sub class B bricks of old size, straight or curved on plan exc 6 m mean radius, built in cement mortar 1:6 complete all as specified and directed by Engineer-in-Charge. |
| 77 | Supply and fixing brass chromium plated tublar towel rail 20mm dia ,fancy type, 60cm long,superior quality , between flanges fixed to wall with brass CP screws complete as specified and directed. |
| 78 | Material and labour for Precast RCC 1:2:4 type B1 (using 20mm graded stone aggregate) as in cover slab of drain, culvert and the like set in CM 1:4 complete all as specified and as directed. |
| 79 | Material and labour for plan cement concrete in roof, kerbs , interlocking tiles or rounded or chamfered on edged type B-1 1:2:4 ( 20 mm graded stone aggregate) complete all as specified and as directed by Engineer-in-Charge. Please Enable Macros to View BoQ information |
| 80 | Material and labour for plan cement concrete in roof, kerbs , interlocking tiles or rounded or chamfered on edged type B-1 1:2:4 ( 20 mm graded stone aggregate) complete all as specified and as directed by Engineer-in-Charge. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 28, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 18, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 17 daysAug 20, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 19 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender