Tender For Construction Of Bio-Medical Waste (Bmw) Shed At Hbch&Rc, Muzaffarpur, Bihar- 842004.
Tender Value
36.66 Lakhs
Estimated cost
Bid Submission
17 Aug 2026
20 days left
EMD
73328
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Muzaffarpur → Bihar
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Construction Of Bio-Medical Waste (Bmw) Shed At Hbch&Rc, Muzaffarpur, Bihar- 842004.
BOQ
| Sl. No. | Item Description |
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth, 1.5m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth, lead up to 50m and lift up to 1.5m,as directed by Engineer-in-Charge. All kinds of soil |
| 2 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m. |
| 3 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources). |
| 4 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 5 | Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete |
| 6 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 7 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 8 | 12 mm cement plaster of mix : 1:6 (1 cement: 6 fine sand) |
| 9 | Structural steel work in single section, fixed with or without connecting plate,including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete |
| 10 | Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters. 80x1.25 mm M.S. laths with 1.25 mm thick top cover. |
| 11 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes. |
| 12 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :Two or more coats on new work. |
| 13 | Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in-chargeMade of G.I. wire of dia 4 mm |
| 14 | Providing and fixing 15 cm wide, 45 cm overall semi-circular plain G.S. sheet gutter with iron brackets 40x3 mm size, bolts, nuts and washers etc., including making necessary connections with rain water pipes complete. 0.63 mm thick with zinc coating not less than 275 gm/m* |
| 15 | Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 250 mm dia. R.C.C. pipe |
| 16 | Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 fine sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design: Inside dimensions 455x610 mm and 45 cm deep for single pipe line : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 17 | Constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C. horizontal grating with frame complete as per standard design : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 18 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink with drain board |
| 19 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 75 mm diameter |
| 20 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm diameter |
| 21 | Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansionSingle pushfit Coupler : 75mm |
| 22 | Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansionSingle pushfit Coupler :110mm |
| 23 | Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion Single tee with door -75x75x75 mm |
| 24 | Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion Single tee with door -110x110x110 mm |
| 25 | Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansionBend 87.5° -75 mm bend |
| 26 | Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion- Bend 87.5- 110 mm bend |
| 27 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. Internal work :15 mm nominal dia Pipes |
| 28 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. Internal work :20 mm nominal dia Pipes |
| 29 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. Internal work :25 mm nominal dia Pipes |
| 30 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:893115mm nominal bore |
| 31 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Flat back wash basin size 550x400 mm with single 15 mm C.P. brass pillar tap |
| 32 | Flexible (coil shaped) PVC waste pipe for sink and wash basin 32 mm dia with length not less than 700 mm i/c PVC waste fittings |
| 33 | Providing and fixing brass stop cock of approved quality : 15 mm nominal bore |
| 34 | Providing and fixing brass bib cock of approved quality : 15 mm nominal bore |
| 35 | Providing and fixing Stainless Steel Health Faucet of approved quality : 15 mm nominal bore |
| 36 | Providing and fixing PVC Door Frame of size 50x47 mm with a wall thickness of 5 mm (± 0.2 mm), made out of single piece extruded PVC profile, with mitred cut joints and joint with 2 nos of PVC bracket of size 190 mm x 100 mm long arms of cross section size 35 x 15 mm & self driven self taping screws, the vertical door profiles to be reinforced with40x20 mm M.S. rectangular tube of 0.8 mm , including providing EPDM rubber gasket weather seal throughout the frame, including jointing 5 mm PVC frame strip with PVC solvent cement on the back of the profile.The door frame to be fixed to the wall using 8 x100 mm long anchor fasteners complete, all as per manufacturer's specification and direction of Engineer -in- charge. |
| 37 | 35 mm thick factory made Solid panel PVC Door shutter, made out of single piece extruded soild PVC profiles, 5 mm (± 0.2 mm) thick, having styles & rails (except lock rail) of size 95 mmx 35 mm x 5 mm, out of which 75 mm shall be flat and 20 mm shall be tapered (on both side), having one side thickness of 15 mm integrally extruded on the hingeside of the profile for better screw holding power, including reinforcing with MS tube of size 40 mm X 20 mm x 1 mm, joints of styles & rails to be mitered cut & joint with the help of PVC solvent cement, self driven self tapping screws & M.S. rectangular pipes bracket of size 190 mm X 100 mm of cross section size 35 mm x 17 mm x 1 mm at each corner.Single piece extruded 5 mm thick solid PVC Lock rail of size 115 mm x 35 mm, out of which 75 mm to be flat and 20 mm to be tapered at both ends, having 15 mm solid core in middle of rail section integrally extruded, fixing the styles & rails with the help of solvent and self driven self tapping screws of 125 mm x 11 mm, including providing 5 mm Single piece solid PVC extruded sheet inserted in the door as panel, all complete as per manufacturer's specification and direction of Engineerin-charge.Non decorative finish (matt finish) |
| 38 | Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick. |
| 39 | Mirror polishing on marble work/Granite work/stone work where ever required to give high gloss finish complete. |
| 40 | Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. |
| 41 | Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. completeOn concrete work |
| 42 | Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. completeSteel Work |
| 43 | Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications :Painting wood work with Deluxe Multi Surface Paint ofrequired shade. Two or more coat applied @ 0.90 ltr/10sqm over an under coat of primer applied @0.75 ltr/10sqm of approved brand and manufacture.Two or more coats applied on walls @ 1.25 ltr/10 sqm. over and including one coat of Special primer applied @ 0.75 ltr / 10sqm |
| 44 | Providing and fixing in position factory made EPS cement sandwich wall/ roof/ floor light weight solid core panels made of core material of EPS granule balls/beads (conforming to IS 4671:1984 and shall have density not less than 15kg per cum) adhesive, cement, sand, flyash and other bonding material in mortar state processed to form in a preset mould. The outer face on both sides of the panels will be non asbestos fiber cement board confirming to IS 14862:2000 or Calcium silicate board confirming to EN 14306:2009 of 5mm thick each. Panel shall be laid on 6mm thick cement mortar (1 cement: 2 fine sand) mixed with chemical adhesive of 0.5kg per 50kg of cement or shall be preferably fixed into 'C' channel made of 1.2mm thick MS plate screwed/fastenened to the slab/column/beam etc. The panel shall fixed vertically with tongue and groove joint and horizontally locked with steel bar between each other and floors and filled with cement mortar and adhesive. Panels should be used as floor & roofing with additional structural support, steel or RCC depending upon the design. All the operation shall be completed in all respect as per drawings, Manufacturers specifications and under the overall direction of Engineer-in-Charge (Cost of all the material is included except \\"C channel\\" which will be paid seperately). Non load bearing panels 50mm thick of required size |
| 45 | Providing, supplying, erecting and fixing Factory-Made Corrugated PUF Insulated Sandwich Panels for Roof and Wall Cladding of BMW (Bio-Medical Waste) Shed, comprising pre-painted galvanized steel (PPGI/GI) outer and inner facings with rigid Polyurethane Foam (PUF) insulation core of approved density, complete with self-drilling/self-tapping screws, EPDM washers, ridge pieces, flashing, trims, gutters, sealants, corner profiles and all accessories required for a weatherproof and leak-proof installation. The panels shall be fixed over the structural steel framework as per manufacturer’s specifications and Engineer-in-Charge’s directions, including cutting, lifting, handling, sealing of joints and making good all incidental works.50 mm thick Corrugated PUF Wall Panel, 0.50/0.50 mm PPGI sheets |
| 46 | Providing, supplying, erecting and fixing Factory-Made Corrugated PUF Insulated Sandwich Panels for Roof and Wall Cladding of BMW (Bio-Medical Waste) Shed, comprising pre-painted galvanized steel (PPGI/GI) outer and inner facings with rigid Polyurethane Foam (PUF) insulation core of approved density, complete with self-drilling/self-tapping screws, EPDM washers, ridge pieces, flashing, trims, gutters, sealants, corner profiles and all accessories required for a weatherproof and leak-proof installation. The panels shall be fixed over the structural steel framework as per manufacturer’s specifications and Engineer-in-Charge’s directions, including cutting, lifting, handling, sealing of joints and making good all incidental works.50 mm thick Corrugated PUF Wall Panel, 0.50/0.50 mm PPGI sheets |
| 47 | Providing, supplying, erecting and fixing Factory-Made Corrugated PUF Insulated Sandwich Panels for Roof and Wall Cladding of BMW (Bio-Medical Waste) Shed, comprising pre-painted galvanized steel (PPGI/GI) outer and inner facings with rigid Polyurethane Foam (PUF) insulation core of approved density, complete with self-drilling/self-tapping screws, EPDM washers, ridge pieces, flashing, trims, gutters, sealants, corner profiles and all accessories required for a weatherproof and leak-proof installation. The panels shall be fixed over the structural steel framework as per manufacturer’s specifications and Engineer-in-Charge’s directions, including cutting, lifting, handling, sealing of joints and making good all incidental works.60 mm thick Corrugated PUF Wall Panel, 0.50/0.50 mm PPGI sheets |
| 48 | Providing and Supply and Application of 3mm thick industrial Epoxy for flooring- a) Construction joints treatment - All floor cracks to a Construction joints treatment - All floor cracks to grout. Uneven floor to be grinded and made even gradient.b) Surface preparation – The entire surface shall be bethoroughly levelled, cleaned and made dust free, followed removal of all existing sealants and fill all construction joints using epoxy mortar.c)Epoxy primer 100 microns - An epoxy primer shall be applied |
| 49 | Surical scrub sinkSITC Surical scrub sink made-up of entire body in 2 mm thick SS 304 grade plate & suitable size square frame, unit size 1500mm X 600mm and Height 900 mm floor mounted having following features:1. automatic sensor option,2. hot & cold water option3. Various water dispenser options: Digital sensor, Infrared sensor, Foot, Knee, and Elbow operated arrangements4. Multiple soap dispenser options: Sensor, Foot, Knee, and Elbow operated arrangements5. Front removable panels for routine maintenance and liquid refilling 6. Matt finishing for a clean and professional appearanceCurved corners into ¼” radius with a sloped curve in the basin to eliminate back splash including all accessories, , heavy duty swan neck tap on sink, P & S trap, flexible connectors, etc all as per directions of EIC .Make: CMP Metal, Modular System, Hybeat or equivalent |
| 50 | Supply, Installation, Testing and commissioning of 24'' inch dia wind driven turbo Ventilator system in aluminium along with frp base plate of approved type.MOC of Vanes : Industrial Hi grade Aluminium MOC of Top Plate : SS 304 MOC of Inner Cover : SS 304MOC Bottom of Ring : SS 304Weight of Ventilator without InstallationHardware : 06.00 KsHeight of Ventilator without FRP Base : 410 mm ± 5 mmCenter width of Ventilator : 735mm ± 5 mmDia of Top Plate : 500 mm ± 5 mm Center Shaft : Assembly EN8, 12.5 mm thk solid bar with concealed case of 30 mm dia having high wind resistance lock and bearing dust & Smoke Protector.Dia of Bottom Ring : 600 mm ± 5 mmNos of Vanes : 42 Nos Rolled formed with Lock Washer Thickness of Vanes : 0.5 mmNo of Bearing : 02 NosBearing Type : SKF/FAG-6001 ZZ Twin Sealed permanently LubricatedRivets : Aluminium Alloy with Lock washerAngle Adjuster : SS (0to 17 deg variable)Bare : FRP Bare PlateUV : Treated Bare Plate |
| 51 | Supplying, installing, testing and commissioning of direct driven PROPELLER FANS for exhaust/fresh air as shown in drawings. Each fan shall be complete with permanent split capacitor or shaded pole motor, mounting plate, accessories like wire guard, bird screen and fixed louvers for weather protection as required.Fan shall be provided with speed regulator and NC level 3M away from source shall be less than 55db. Fan selection arrangement and Electrical characteristics shall be as follows :150 mm dia 1400 RPM fan suitable for 220±6% volts 50 cycles, 1 phase AC supply, The Fan Materials is Black color, made from Steel sheet specification approved by by Engineer -Incharge. |
| 52 | Providing consultancy services for structural design, vetting of structural drawings/design calculations, and issuance of Structural Stability/Safety Certificate by a competent licensed Structural Engineer, complete in all respects. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 27, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 17, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 20 daysAug 18, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 21 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender