Tender For Stop Gap Arrangement For 90 Days Day To Day Maintenance Including Up Keeping Work At N.S Nagar Township, Bocp Under Bharatpur Area .Nit No:Gm(Ba)/So(Civil)/E-Tender/2026-27/301 Dt.24.07.2026
Tender Value
1.94 Crore
Estimated cost
Bid Submission
11 Aug 2026
14 days left
EMD
2.43 Lakhs
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Anugul → Odisha
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Stop Gap Arrangement For 90 Days Day To Day Maintenance Including Up Keeping Work At N.S Nagar Township, Bocp Under Bharatpur Area .Nit No:Gm(Ba)/So(Civil)/E-Tender/2026-27/301 Dt.24.07.2026
BOQ
| Sl. No. | Item Description |
| 1 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws |
| 2 | Providing and fixing to existing door frames: 24 mm thick factory made PVC door shutters made of styles and rails of a uPVC hollow section of size 59x24 mm and wall thickness 2 mm (± 0.2 mm) with inbuilt edging on both sides. The styles and rails mitred and joint at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 20x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of 'H' section, a uPVC hollow section of size 100x24 mm and 2 mm (± 0.2 mm) wall thickness, fixed to the shutter styles by means of plastic/galvanised M.S. 'U' cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer's specification and direction of Engineer-in-charge. (For W.C. and bathroom door shutter). |
| 3 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete Fixed to openings /wooden frames with rawl plugs screws etc. |
| 4 | Providing and fixing Pre-laminated flat pressed 3 layer (medium density) particle board or graded wood particle board IS : 3087 marked, with one side decorative and other side balancing lamination Grade I, Type II exterior grade IS : 12823 marked, in shelves with screws and fittings wherever required, edges to be painted with polyurethane primer (fittings to be paid separately).18 mm thick |
| 5 | Applying priming coat: With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works |
| 6 | Renewing glass panes, with putty and nails wherever necessary including racking out the old putty: Float glass panes of thickness 4 mm |
| 7 | Renewal of old putty of glass panes (length) |
| 8 | Providing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), complete. |
| 9 | Providing ISI marked oxidised M.S. sliding door bolts : 250x16 mm |
| 10 | Providing ISI marked oxidised M.S. handles conforming to IS:4992 : 125 mm |
| 11 | Providing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) : 250x10 mm |
| 12 | Providing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade : 150x10 mm |
| 13 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :100mm |
| 14 | Providing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, : 250x16 mm |
| 15 | Providing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, . Twin rubber stopper |
| 16 | Providing ISI marked M.S. pressed butt hinges bright finished etc. complete : 125x65x2.12 mm |
| 17 | Providing and fixing chromium plated brass curtain rod having wall thickness of 1.25mm with two chromium plated brass brackets fixed with C.P. brass screws and PVC sleeves etc., wherever necessary complete : 25 mm dia |
| 18 | Providing SS wire mesh jali for doors and window of 22 gauge 18 mesh per sq inch as per instruction of Engineer-in-charge. Grade 304 |
| 19 | Providing 28 gauge aluminium sheet (to be fixed in door) as per instruction of Engineer-in-charge. |
| 20 | Labour charges of deploying 03 (three) skilled carpenter and 03 (Three) unskilled helper for day to day maintance works related with Carpentary works as per instruction of Engineer-in-charge (on week days) |
| 21 | Supplying Chromium plated brackets for ( curtain rods)25mm |
| 22 | Supplying Brass screws 30 mm |
| 23 | Supplying Bright finished or black enamelled mild steel screws 50 mm |
| 24 | Supplying Chromium plated Brass screws 30 mm |
| 25 | Supplying Oxidised mild steel screws 30 mm |
| 26 | Supplying Oxidised mild steel screws 25 mm |
| 27 | Supplying Bright finished or black enamelled mild steel bolts and nuts 50x6 mm |
| 28 | Suppying Bright finished or black enamelled mild steel butt hinges 125x65x2.12 mm |
| 29 | Providing welding rod as per instruction of Engineer-in-charge |
| 30 | Providing and fixing 12 mm thick panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick. Marine plywood conforming to IS: 710 |
| 31 | Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 1.5 mm thick |
| 32 | Providing sliding glass runner as per instruction of Engineer-Charge. |
| 33 | Removing of damage glass panes & providing and fixing frosted glass panes in door window withslidding glass runner, rubber and necessary screw fitting as per instruction of Engineer-in-charge |
| 34 | Providing M.S nail of different sizes |
| 35 | Providing and fixing factory made UPVC door frame made of UPVC extruded sections having an overall dimension as below (tolerance tlmm), with wall thickness 2.0 mm (t 0.2 mm), corners of the door frame to be Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 x 19 mm and lmm (t 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer's specification and direction of Engineer- in-charge Extruded section profile size 42x50 mm |
| 36 | Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high densitv protective surface layer and reverse side of adhesive bonding quality conforming to lS : 2046 Type S, including cost of adhesive of approved quality-1.0 mm thick |
| 37 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth. 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed. All kinds of soil |
| 38 | Supplying and filling in plinth with river sand under floors, including watering, ramming, consolidating and dressing complete. |
| 39 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) |
| 40 | Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge. |
| 41 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) |
| 42 | 6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand) |
| 43 | Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. |
| 44 | 12 mm cement plaster of mix :1:6 (1 cement: 6 fine sand) |
| 45 | Brick work with Fly Ash Brick (230x125x75 mm size) bricks of class designation 10 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 46 | Brick work with Fly Ash Brick (230x125x75 mm size) bricks of class designation 10 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 47 | Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.: 40 mm thick with 20 mm nominal size stone aggregate |
| 48 | Grading roof for water proofing treatment withCement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) |
| 49 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm |
| 50 | Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), including pointing the joints with white cement and matching pigments etc., complete. |
| 51 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 52 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge.: Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) |
| 53 | Distempering with 1st quality acrylic distember (Ready mix) having VOC content less than 50 grams/ litre of approved brand and manufacture to give an even shade :Old work (one or more coats) |
| 54 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : One or more coats on old work |
| 55 | Finishing walls with Acrylic Smooth exterior paint of required shade : Old work (One or more coat applied @ 0.90 ltr/10 sqm). |
| 56 | Finishing walls with Acrylic Smooth exterior paint of required shade :New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) |
| 57 | Providing, hoisting and fixing above plinth level up to floor five level precast reinforced cement concrete work in string courses, bands, copings, bed plates, anchor blocks, plain window sills and the like, including the cost of required centering, shuttering but , excluding cost of reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). |
| 58 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars |
| 59 | Centering and shuttering including strutting, propping etc. and removal of form work for : Retaining walls, return walls, walls (any thickness) including attached pilasters, buttresses, plinth and string courses fillets, kerbs and steps etc. |
| 60 | Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge : In cement mortar |
| 61 | Chequered precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand).: Medium shade pigment using 50% white cement 50% Grey cement |
| 62 | CARRIAGE OF MATERIALS By Mechanical Transport including loading,unloading and stacking Lime , moorum, building rubbish for 2 km |
| 63 | Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content.With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre |
| 64 | Providing white cement as per instruction of Engineer-in-charge |
| 65 | Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour.Two coats |
| 66 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 Sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil. |
| 67 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) |
| 68 | Providing and fixing 18 mm thick gang saw cut, mirror polished, pre-moulded and pre-polished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade: Area of slab over 0.50 sqm |
| 69 | Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge : Granite work |
| 70 | Providing and applying white cement based putty of average thickness 1mm of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete |
| 71 | Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement: 4 Coarse sand), including grouting the joints with white cement and matching pigments etc., complete. |
| 72 | Finishing walls with water proofing cement paint of required shade : Old work (one or more coats applied @ 2.20 kg/10 sqm) over priming coat of primer applied @ 0.80 litrs/10 sqm complete including cost of Priming coat. |
| 73 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shadeNew work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) |
| 74 | Distempering with 1st quality acrylic distemper, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour. One coat |
| 75 | Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. |
| 76 | Neat cement punning. |
| 77 | 12 mm cement plaster finished with a floating coat of neat cement of mix : 1:3 (1 cement: 3 fine sand) |
| 78 | Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead For thickness of tiles 10 mm to 25 mm |
| 79 | Dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within 50 metres lead of: G.S. Sheet |
| 80 | Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq. meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground within 50 metres lead : With cement mortar 1:4 (1 cement : 4 fine sand) |
| 81 | Labour charges including tools and plants for day to day maintenance work like brick work, plastering, flooring and other petty jobs as and when required on daily basis by deploying masons. Beldar /coolie in residential quarters of Colony (Materials to be used in this item are to be paid separately) as per instruction of Engineer-in-charge. (2 Skilled and 2 unskilled worker per day) |
| 82 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 83 | Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick |
| 84 | Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. |
| 85 | Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete.: Size of Tile 600x600 mm |
| 86 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Raj Nagar Plain white marble/ Udaipur green marble/ Zebra black marble : Area of slab upto 0.50 sqm |
| 87 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 88 | Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+ 0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : Gutter .(600 mm over all girth) |
| 89 | Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+ 0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : Ridges plain (500 - 600mm) |
| 90 | Half brick masonry with Fly Ash Brick (230x125x75 mm size) bricks of class designation 10 in foundations and plinth in : cement mortar 1:4 (1 cement : 4 coarse sand) |
| 91 | Half brick masonry with Fly Ash Brick (230x125x75 mm size) bricks of class designation 10 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand) |
| 92 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work |
| 93 | Supplying and stacking at work site coarse clean sand with all lead and royalty, all complete. |
| 94 | Supply of Stone Aggregate (Single size) : 20 mm nominal size as per instruction of Engineer-in-charge |
| 95 | Supplying of putty as per instruction of Engineer-incharge. |
| 96 | Supply of Portland Cement (OPC-43 Grade) as per instruction of engineer in charge. |
| 97 | Lettering with black Japan paint of approved brand and manufacture |
| 98 | Supplying and stacking at work site crusher stone dust including royalty complete with all leads and lifts. |
| 99 | Spreading moorum/sand/ stone dust etc. in layers not exceeding 150mm in thickness, levelling to required gradient and camber, watering and consolidation of each layer with vibratory roller (Payment to be made for compacted volume of moorum/sand). |
| 100 | Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 250 mm dia. R.C.C. pipe |
| 101 | Fencing with R.C.C. post placed at required distance, embedded incement concrete blocks, every 15th post, last but one end post andcorner post shall be strutted on both sides and end post one sideonly, provided with horizontal lines and two diagonals of barbed wireweighing 9.38 kg per 100 metres (minimum), between the two postsfitted and fixed with G.I. staples on wooden plugs or G.I. binding wiretied to 6 mm bar nibs fixed while casting the post (cost of R.C.C.posts, struts, earth work and concrete to be paid for separately) :-Payment to be made per metre cost of total length of barbed wire used.With G.I. barbed wire |
| 102 | Providing and fixing 1st quality Ultracharge Vitrified wall tiles conforming to IS : 15622 (thickness to be specified by the manufacture of SOMANY or other approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.(800x1600mm wall tiles) |
| 103 | Providing 653-Dr fixit roof seal select heavy duty reinforced traffic water proof coating coverage 7-8 sqft L/3 or equivalent make coat as per EIC. |
| 104 | Providing 653- Dr. fixit prime seal select heavy duty reinforced traffic water proof coating coverage 7-8 sqft L/3 or equivalent make coat as per instruction of EIC. |
| 105 | Making hole for air conditioner in wall and disposal of debris, side plastering with cement mortar 1:4 (1 cement : 4 fine sand) etc. complete and finishing with white cement base wall putty and distemper to match with the existing colour as per direction of EIC. (Approx size of the hole 27\\" x 18\\") |
| 106 | Supply of Fly ash bricks conforming to I.S. 12894 as per instruction of EIC. |
| 107 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work - Exposed on wall 40 mm dia nominal bore |
| 108 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 15 mm nominal outer dia Pipes |
| 109 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.Concealed work, including cutting chases and making good the walls etc. 20 mm nominal outer dia Pipes |
| 110 | Providing and fixing on wall face PVC SWR pipes conforming to IS : 13592 , including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. (In case SWR pipes is laid on ground, cost of trenching & filling, if required is to be paid separately)110 mm diameter (Type A) |
| 111 | Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc.External work :80 mm dia nominalbore |
| 112 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 113 | Providing and fixing C.I. sluice valves (with cap) complete with bolts, nuts, rubber insertions etc. (the tail pieces if required will be paid separately) :100 mm diameter : Class I |
| 114 | Providing and fixing C.I. sluice valves (with cap) complete with bolts, nuts, rubber insertions etc. (the tail pieces if required will be paid separately) : 150 mm diameter : Class II |
| 115 | Welding by gas or electric plant including transportation of plant at site etc. complete. |
| 116 | Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : All kinds of soilPipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia |
| 117 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid |
| 118 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests |
| 119 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap |
| 120 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink with drain board 510x1040 mm bowl depth 250 mm |
| 121 | Providing and fixing of 100mm G.I pipes complete with G.I fittings including trenching & refilling(External work) all complete as per instruction of the EIC. |
| 122 | providing Chlorinated Polyvinyl - chloride (CPVC) pipe 20 mm nominal dia of approved quality. |
| 123 | providing Chlorinated Polyvinyl - chloride (CPVC) pipe 25 mm nominal dia of approved quality. |
| 124 | providing Chlorinated Polyvinyl - chloride (CPVC) pipe 32 mm nominal dia of approved quality. |
| 125 | providing Chlorinated Polyvinyl - chloride (CPVC) pipe 40 mm nominal dia of approved quality. |
| 126 | providing Chlorinated Polyvinyl - chloride (CPVC) pipe 50 mm nominal dia of approved quality. |
| 127 | Providing and fixing on wall face PVC SWR pipes conforming to IS : 13592 , including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.(In case SWR pipes is laid on ground, cost of trenching & filling, if required is to be paid separately) 75 mm diameter (Type A) |
| 128 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.110 mm diameter |
| 129 | Providing CI bracket for Wash Basin and sink as per instruction of Engineer-in-charge. |
| 130 | Providing Semi Rigid PVC waste pipe for sink and wash basin 32 mm dia with length not less than 700 mm i/c PVC waste fittings, as per instruction of Engineer-in-charge. |
| 131 | Providing Semi Rigid PVC waste pipe for sink and wash basin 40 mm dia with length not less than 700 mm i/c PVC waste fittings, as per instruction of Engineer-in-charge. |
| 132 | Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete. |
| 133 | Providing mirror of superior make glass 600X450 mm, as per instruction of Engineer-in-Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 134 | Providing Flushing Cistern P.V.C. 10 litre capacity (low level) (White) (with fittings, accessories and flush pipe), as per instruction of Engineer-in-charge. |
| 135 | Providing C.P.brass bib cock 15 mm nominal bore of approved quality, as per instruction of Engineer-in-charge. |
| 136 | Providing C.P.brass stop cock 15 mm nominal bore of approved quality, as per instruction of Engineer-in-charge. |
| 137 | Providing and fixing 15 mm CP brass pillar tap of approved quality by (PLAZA brand or equivalent) as per instruction of Engineer-in-charge. |
| 138 | Providing C.P. brass waste for sink or wash basin : 32 mm as per instruction of Engineer-in-Charge. |
| 139 | Providing C.P. brass waste for sink or wash basin : 40 mm as per instruction of Engineer-in-Charge. |
| 140 | Providing CPVC UNION - 20mm dia of approved quality as per instruction of Engineer-in-charge |
| 141 | Providing brass R.S. (20mm to 15 mm) of approved make as per instruction of EIC. |
| 142 | Providing brass R.T. (20mm to 15 mm) of approved make as per instruction of EIC. |
| 143 | Providing CPVC FTA brass of approved make as per direction of EIC. 20 mm dia |
| 144 | Providing CPVC Male threaded tee brass of approved make as per direction of EIC. 20 mm dia |
| 145 | Providing Unplasticised P.V.C. connection pipe with brass union 45 cm long 15 mm bore confirming to relevant IS as per direction of EIC. |
| 146 | Providing CPVC female threaded brass elbow of approved make as per direction of EIC. 20mm dia |
| 147 | Providing CPVC female threaded brass elbow of approved make as per direction of EIC. 25mm dia |
| 148 | Providing CPVC reducing Tee of approved make as per direction of EIC 40X25 |
| 149 | Providing CPVC TEE - 20mm dia of approved quality as per instruction of Engineer-in-charge |
| 150 | Providing CPVC UNION - 25mm dia of approved quality as per instruction of Engineer-in-charge |
| 151 | Providing Stainless steel Spindle with check nut for 4” Valve approved make as per direction of EIC |
| 152 | Providing Stainless steel Spindle with check nut for 6” Valve approved make as per direction of EIC |
| 153 | Providing CPVC SOCKET - 25mm dia of approved quality as per instruction of Engineer-in-charge |
| 154 | Providing CPVC SOCKET - 20mm dia of approved quality as per instruction of Engineer-in-charge |
| 155 | Providing flush bend for flushing cistern of length 1.00 Mtr of approved make as per direction of EIC. |
| 156 | Providing CPVC female threaded brass elbow of approved make as per direction of EIC. 25mm dia |
| 157 | Providing PVC washer suiatable for brass bib cock and stop cock of approved make as per direction of EIC |
| 158 | Providing CPVC Tank nipple 25MM dia of approved quality as per instruction of Engineer-in-charge |
| 159 | Providing M-seal adhesive or equivalent (in packets of 100 gm) as per instruction of Engineer-in-Charge. |
| 160 | Providing fevicol or equivalent adhesive of approved quality as per instruction of Engineer-in-charge. |
| 161 | Providing and fixing C.P. shower rose with arm (Plaza brand or equivalent) of approved quality complete with 15 mm or 20 mm inlet 100 mm diameter as per instruction of Engineer-in-Charge. |
| 162 | Providing Brass full way valve with C.I. wheel (screwed end) 40 mm dia confirming to relevant IS as per direction of EIC. |
| 163 | Providing polyethylene water storage tank cover as per instruction of Engineer-in-charge. |
| 164 | Providing 15 mm PTMT bib cock of approved make as per direction of EIC |
| 165 | Providing PTMT pillar cock of approved quality and colour . 15 mm nominal bore, 125 mm long foam flow, weighing not less than 120 gms of approved make as per instruction of EIC |
| 166 | Providing CPVC UNION - 32mm dia of approved quality as per instruction of Engineer-in-charge |
| 167 | Providing CPVC UNION - 40mm dia of approved quality as per instruction of Engineer-in-charge |
| 168 | Providing CPVC UNION - 50mm dia of approved quality as per instruction of Engineer-in-charge |
| 169 | Providing CPVC PLAIN ELBOW- 32mm dia of approved quality as per instruction of Engineer-in-charge |
| 170 | Providing CPVC PLAIN ELBOW- 50mm dia of approved quality as per instruction of Engineer-in-charge |
| 171 | Providing CPVC Male threaded tee brass of approved make as per direction of EIC. 25mm dia |
| 172 | Providing CPVC Male threaded tee brass of approved make as per direction of EIC. 40mm dia |
| 173 | Providing CPVC SOCKET - 32mm dia of approved quality as per instruction of Engineer-in-charge |
| 174 | Providing CPVC SOCKET - 40mm dia of approved quality as per instruction of Engineer-in-charge |
| 175 | Providing PVC VALVE 25mm dia of approved quality as per instruction of Engineer-in-charge |
| 176 | Providing PVC VALVE 50mm dia of approved quality as per instruction of Engineer-in-charge |
| 177 | Providing PVC VALVE 40mm dia of approved quality as per instruction of Engineer-in-charge |
| 178 | Providing Wall Mixer 3 in 1 Quarter turn of approved brand Jaquar or equivalent make as per direction of EIC |
| 179 | Providing 80mm dia G.I flange as per instruction of EIC |
| 180 | Providing CP brass health faucet with tube AND HOOK SET as per direction of EIC |
| 181 | Providing CP brass two in one bibcock of approved brand Jaquar or equivalent make as per direction of EIC |
| 182 | Providing PTMT - Towel Rail (600 mm) of approved make as per direction of EIC |
| 183 | Providing PVC 'P' trap 100 mmX100 mm for European pan of approved make as per direction of EIC |
| 184 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes screwed with M.S. screws of required length etc. complete. 110 mm |
| 185 | Providing pvc 100 mm X100 mm nahani trap of approved make as per direction of EIC. |
| 186 | Providing C.P. towel rod size 600x20mm with C.P. brass screws to be approved by Engineer-in-Charge (PLAZA brand or equivalent) as per instruction of Engineer-in-charge. |
| 187 | Providing PTMT grating 100 mm dia of approved make as per direction of EIC |
| 188 | Providing Vitreous china pedestal for wash basin |
| 189 | Extra charge for Day to day maintenance of plumbing work etc. with all labour cost but excluding cost of materials as per instruction of Engineer Incharge. (For Colonies with more than 600 Quarters or for very old colonies with 500 quarters) |
| 190 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink without drain board 610x510 mm bowl depth 200 mm |
| 191 | Cleaning and dewatering of all water line valve chambers as per instruction of EIC |
| 192 | Day to day maintance of water supply net work and plumbing work etc. with all labour cost but excluding cost of materials as per instruction of Engineer-in-charge(3 Skilled AND 3 Unskilled worker per day) |
| 193 | Cleaning of over head water tank (HDPE / Masonary) by applying bleaching powder, washing the tank neatly as per instruction of EIC |
| 194 | Removal of chokage/blockage of sewer lines by removing silt, sludge and other foreign materials and disposal of the same to the nearest dustbins etc. complete as per the direction of the engineer-in-charge. |
| 195 | Cleaning of Drains without siltation or sludge deposition: Open Surface drain up to 250 mm width. |
| 196 | Upkeeping of concrete pavement/ Black topped roads excluding coal transport road by brooming and disposal of collected debris/ waste at collection pit/ dustbins or at specified locations within a lead of 50 metres including all tools & plants like spade, basket, brooms with handle stick complete as per the direction of Engineer-In-Charge. |
| 197 | Carriage of sludge or manure including of loading unloading and stacking of same at 4 kms lead, as per instruction of Engineer-incharge. |
| 198 | Removal of chokage / blockage of inspection chambers by removing silt, sludge and other foreign materials and disposal of the same to the nearest dustbins etc. Complete as per the direction of engineer-In-Charge. |
| 199 | Removal of chokage / blockage of manholes by removing silt, sludge and other foreign materials and disposal of the same to the nearest dustbins etc. Complete as per the direction of engineer-In-Charge. |
| 200 | Clearing jungle including uprooting of rank vegetation, grass,brush wood, trees and saplings of girth upto 30 cm measured at a height of 1 m above ground level and removal of rubbish upto a distance of 50 m outside the periphery of the area cleared, as per instruction of Engineer-incharge.(Quantity in Sqm) |
| 201 | Clearing grass and removal of the rubbish upto a distance of 50 m outside the periphery of the area cleared, as per instruction of Engineer-incharge. |
| 202 | Felling trees of the girth (measured at a height of 1 m above ground level), including cutting of trunks and branches, removing the roots and stacking of serviceable material and disposal of unserviceable material.Beyond 60 cm girth upto and including 120 cm girth |
| 203 | Cleaning of Drains without siltation or sludge deposition: Open Surface drain above 250 mm width. |
| 204 | Cleaning and brooming of floor areas like chequered tiles, IPS floors, including applying water, detergents etc adequately all complete as per the direction of Engineer-In-Charge. |
| 205 | Cleaning of drains including removal of earth/ slush/ mud/ silt etc. from drains including disposal of the same within a lead of 50 metres. |
| 206 | Disposal of dead animals like street dog,pigs,cat etc. as an when required including digging of pits and buring the same as per instrution of engineer in charge |
| 207 | Disposal of dead animals like cow,ox,buffalow etc. as an when required including digginhg of pits and buring the same as per instrution of engineer in charge |
| 208 | Cleaning and uprooting of trees/plants/vegetation/debris on the building including uprooting of rank vegetation on the building blocks, water tanks,chajja,kitchen/sanitary pipes,walls etc. including repairing plastering and removal of the rubbish/debris and disposal up to nearest dustbin with all lead and lift as per direction of EIC |
| 209 | Trimming of trees & cutting of dead part of trees in colony,near other structures etc and disposal of the same at an appropriate place as per instruction of Engg I/c. |
| 210 | Up keeping of inside office/ service / welfare buildings including: a) Cleaning of floors by brooming and mopping, walls ceiling, partitions, chairs, tables, almirahs, staircases, verandahs, balconies, window glass panes, small drain adjoining plinth protection etc. once in a day in the officebuilding daily in all working days. (b) Cleaning of bathroom / toilets once in a day with water, detergent, phenyl etc. daily in working days inclusive of Cost of detergents and other toiletaries as per the direction of Engineer-In-Charge. |
| 211 | Supplying providing harpic solution or its equivalent approved brand for cleaning of toilets as and when required basis as directed by Engineer-in-charge |
| 212 | Upkeeping of residential quarters in the township including cleaning of bathrooms, staircase, courtyard, garage, parking space, premises and surrounding areas including collection of garbage and disposal to the dustbins by engaging sufficient numbers of manpower including cost of all necessary tools and supervision charges etc. all complete as per the direction of EIC. (iii) C-Type Quarter |
| 213 | Upkeeping of residential quarters in the township including cleaning of bathrooms, staircase, courtyard, garage, parking space, premises and surrounding areas including collection of garbage and disposal to the dustbins by engaging sufficient numbers of manpower including cost of all necessary tools and supervision charges etc. all complete as per the direction of EIC. (iv) D-Type Quarter |
| 214 | Supplying and providing Soap based multi-use cleanser and deodorant (BENGAL CHEMICALS tiger brand white phenyl or its equivalent approved brand) in sealed container(s) of 500ml capacity and distributing the same to all residential quarter(s) and service building(s) as direct by Engineer-in charge |
| 215 | Supply and providing of black phenyl (BENGAL CHEMICAL Lamp brand) or its euivalent approved brand in sealed container of 450 ml capacity as per direction of Engineer-in-charge |
| 216 | Supply and providing of bleaching powder conforming BIS specification in sealed bags of 25 kg. capacity as directed by Engineer-in-charge |
| 217 | Cleaning of existing mosaic floor/marble/tile floor with water detergent including brushing and cleaning of existing floor with wire brushes brooms etc. for change of occupancy in quarters as per instruction of Engineer-in-charge |
| 218 | Collection of garbage from different places of colony and disposal of the same at a suitable place as earmarked by municipality/local authorities by suitable mechanical arrangement (Tractor) including loading.unloading complete with all leads as per instruction of Engineer-in-charge (Tractor of 3.00 Cum capacity to be engaged at least twice in a week and no garbage shall be dumped in colony premises Tractor trip in colony premises should be duly authenticated by concerned TA authorities. Garbage shall be covered properly and tied in order to avoid any slippage during transit). |
| 219 | Maintenance of lawn, garden, flower beds, potted plants, plants and trees, planting of new plants / new lawns as and where required including watering, removal of weeds, wild vegetation etc, manuring, putting good earth, fertilisers, applying pesticides at various locations etc. as per the direction of Engineer-In-Charge. (Cost of plants, manure, good earth, etc. to be paid for separately. However, cost of tools & plants, flexible pipes, fertilisers and insecticide / pesticides are included in the item and is to be arranged by the contractor. The water supply point shall be provided at one point at each separate location by the department.). NOTE: The payment to the workmen shall be made through any nationalised bank. |
| 220 | Supply of seasonal /other flower saplings including carriage to the site as per the instruction of Enginering in-charge. Fly marigold |
| 221 | Supply of seasonal /other flower saplings including carriage to the site as per the instruction of Enginering in-charge. Impatiens |
| 222 | Supply of seasonal /other flower saplings including carriage to the site as per the instruction of Enginering in-charge. Rose |
| 223 | Supply of seasonal /other flower saplings including carriage to the site as per the instruction of Enginering in-charge. Giladia |
| 224 | Supply of seasonal /other flower saplings including carriage to the site as per the instruction of Enginering in-charge. Geranium |
| 225 | Providing and Displaying Bougainvillea named variety, Sobhra, Thima, Marry palmar, Cherry Blossom etc. well developed with fresh & healthy bushy in full bloom 75 to 90 cm ht. in 40 cm Cement Pot as per direction of the officer in charge. |
| 226 | Providing and displaying of Croton Challenger variety having ht. 30cm and above, well developed with full of fresh and healthy leaves in 20 cm size of Earthen pot/Plastic pot & as per direction of the officer in charge. |
| 227 | Providing and displaying of Croton baby golden variety having ht.30 cm and above, well developed with full of fresh and healthy leaves in 20 cm size of Earthen pot/Plastic pot & as per direction of the officer in charge. |
| 228 | Providing and displaying of Croton Baby Golden Punctatum Aureum having ht. 23 cm to 30 cm, well developed with fresh and healthy foliage in 15 cm size of Earthen pot/Plastic pot. as per direction of the officer in charge. |
| 229 | Providing and displaying of Croton Golden having ht. 45 cm to 60 cm with 2 to 3 branches, well developed, fresh and healthy foliage in 25 cm size of Earthen pot/Plastic pot as per direction of the officer in charge. |
| 230 | Providing and displaying of Croton Baby Golden (three in one), having ht. 30cm, multi branches, well developed with fresh and healthy foliage in 25 cm size of Earthen pot/Plastic pot. as per direction of the officer in charge. |
| 231 | Providing and displaying of Croton golden (Broad Leaves) having ht.60 cm to 75 cm with 3 to 4 branches, well developed, fresh and healthy leaves in 25 cm size of Earthen pot/Plastic pot. & as per direction of the officer in charge. |
| 232 | Providing and displaying of Croton Golden specimen having ht. 90 cm to 1.05 cm with 5 to 6 branches, well developed, fresh and healthy foliage in 30 cm size of Earthen pot/Plastic pot as per direction of the officer-in-charge. |
| 233 | Supplying of manure and pesticides/insectisides in a phased manner as per requirement as per direction of Engineer In charge :: Urea |
| 234 | Supplying of manure and pesticides/insectisides in a phased manner as per requirement as per direction of Engineer In charge :Gromor 28-28-0 |
| 235 | Supplying of manure and pesticides/insectisides in a phased manner as per requirement as per direction of Engineer In charge : Murite of potash |
| 236 | Supplying of manure and pesticides/insectisides in a phased manner as per requirement as per direction of Engineer In charge :Mustard cake |
| 237 | Supplying of manure and pesticides/insectisides in a phased manner as per requirement as per direction of Engineer In charge :Neem cake |
| 238 | Supplying of manure and pesticides/insectisides in a phased manner as per requirement as per direction of Engineer In charge :Bone meal dust |
| 239 | Providing and Displaying Marigold jaffri French orange/yellow/Russet colourwell developed with fresh & healthy foliage with 60 to 75 flowers in bloomspecimen plant 60 to 75 cm ht in 30 cm Earthen Pot/Plastic Pot and as perdirection of the officer in charge. |
| 240 | Providing and fixing M. S. tree guard 45 cm square in plan, height 1.20 metre above ground level and 0.40 metre below ground level. The vertical members shall consist of four nos angle iron of size 25x25x3 mm, 1.6 m long, one at each corner and 8 nos flat iron of size 25x3 mm, 1.2 m long. The vertical mambers shall be welded to 4 nos 25x6 mm M. S. flats placed horizontally around the vertical member of the cage. One name plate of 1 mm thick M.S. sheet of size 250x100 mm shall be welded to the tree guard near the middle height and lettered CPWD / PWD/ any other approved name. The tree guard shall be fixed to the ground by making suitable holes and by embedding four corners leg in the ground, including refilling the earth, compaction etc. complete. The tree guard shall be painted with two or more coats of synthetic enamel paint of approved brand and manufacture over a coat of primer, complete in all respect. |
| 241 | Supplying and stacking of good earth at site including royalty and carriage complete (earth measured in stacks will be reduced by 20% for payment). |
| 242 | Supplying and stacking at site dump manure from approved source, including carriage complete (manure measured in stacks will be reduced by 8% for payment) : Screened through sieve of I.S. designation 20 mm |
| 243 | Mixing earth and sludge or manure in the required proportion specified or directed by the Officer-in-charge. |
| 244 | Providing Circular Cement Concrete pots of specified size, cast with cement concrete of nominal mix 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 6 mm nominal size), reinforced with 7 nos (3 nos horizontal & 4 nos vertical \\"U\\" shape) M.S. wires of 3.5 mm dia as per design, including required form work, finishing with cement punning on exposed surface, curing for specified period and stacking in required rows & height, all complete as per direction of Officer-in-charge.Top inside dia 35 cm, outer bottom dia 25 cm, total height 35 cm with wall thickness of 25.4 mm |
| 245 | Collection of garden wastes from different places of township and disposal of the same at a suitable place away from colony premises by suitable mechanical arrangement (Tractor of carrying capacity of 3 cum) ) including loading, unloading etc complete with all leads as per direction of Engineer-in-Charge. (Tractor should be engaged daily and no garden waste shall be dumped in the colony premises. Tractor trip from colony to outside should be duly supported by exit pass/ gate pass at colony main entrance security post.) Note: Hire charge of tractor is inclusive of lead of 10 KM. The lead may vary as per the requirement. |
| 246 | Providing and laying Neelgiri/Mexican grass turf with earth 50mm to 60mm thickness of existing ground prepared with proper level and ramming with tools wooden (Dhurmos) and than rolling the surface with light roller make the surface smoothen and light waterning with sprinkler and maintenance for 30 days or more till the grass establish properly, as per direction of officer-in-charge. |
| 247 | Providing Technical assitance /Supervisor for Supervision of work and assiting the dept and having good academic record and knledge of computer etc to prepare report etc and work as per instruction of Engineer-in-Charge (01 highly skilled person per day) having good academic record and knowledge of computer etc to prepare report etc and work as per instruction of Engineer-in-charge (02 persons per day) |
| 248 | Up keeping, guarding and operation of STP and pump, motor etc for the whole day i.e 24 hour as per instruction of EIC.Scipe of work: The agency has to deploy 03 nos unskilled manpower per day (one no unskilled manpower in each shift). |
| 249 | Removal of chokage / blockage of inspection chambers by removing silt, sludge and other foreign materials and disposal of the same to the nearest dustbins etc. Complete as per the direction of engineer-In-Charge. |
| 250 | Total impact of GST plus Labour Cess [@ 1 % (BOCW Cess to be deducted from the RA bill as per the value of the work progress)] for the purpose of CTC Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 27, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 11, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 14 daysAug 13, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 16 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender