Tender For Tender Schedule For Extension Of Library Hall From The Existing Room Of Malayalam Library Of Ori Andmssl, Kariavattom C Us-Furnishing.
Tender Value
4.23 Lakhs
Estimated cost
Bid Submission
06 Aug 2026
6 days left
EMD
10600
Bank guarantee accepted
Document Fee
950
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Thiruvananthapuram → Kerala
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Tender Schedule For Extension Of Library Hall From The Existing Room Of Malayalam Library Of Ori Andmssl, Kariavattom C Us-Furnishing.
BOQ
| Sl. No. | Item Description |
| 1 | Extension ORI |
| 2 | 10.25.2Item Shifted to Sub head 14 as item 14.73Item Shifted to head 14 as item 14.74 Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works |
| 3 | OD339530/2025-2026Steel work welded in built up sections/framed work, including fabricating by making curvature/ curvilinear portion using machine bending, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In architectural fabrications, trusses and similar works |
| 4 | 21.1.2.2For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately)Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 5 | OD339552/2025-2026Providing and fixing 3mm thick ACP sheet ,in paneling fixed in aluminum doors windows shutters and partition frames with brass/stainless screws etc complete as per architectural drawings and direction of Engineers in charge. |
| 6 | 50.9.11.1Providing and fixing Thomson Multi wood board or equivalent make paneling 12 mm thick, to frame, backing or studding with screws etc. complete ( Frames, backing or studding to be paid separately) as per the direction of site Engineer-in-charge. |
| 7 | 9.79.1Providing and fixing special quality bright finished brass cupboard or ward robe locks with four levers of approved quality including necessary screws etc. complete.40 mm |
| 8 | 10.30.2Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows all complete with :5.5 mm thick glass panes |
| 9 | 9.115providing and fixing powder coated telescopic drawer channels 300 mm long with necessary screws etc. complete as per directions of Engineer -in-charge. |
| 10 | OD339753/2025-2026Providing and fixing 18 mm thick gang saw cut, mirror, polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over frame work ,joints treated with adhesive including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. |
| 11 | OD339754/2025-2026Supplying and providing auto closer soft closing hinges of approved quality for cupboard shutters with screws etc. complete as per direction of engineer in charge |
| 12 | 13.61.1Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:Two or more coats on new work |
| 13 | OD54006/2026-2027Supply of heavy duty steel slotted angle racks with 7 panels. The framework angles (40mm) are 2mm tk. and made through advanced technical process using CR mild and HR steel. The rack sheets to be used are of 18guage with 1.3inch square support with two under support channels in each panel(40x10mm size). Both side and central partition, including 120mm ht. Intermediate partition in racks are to be provided with 18guage sheet.Rate includes all finishing works including fixing floor rubber bush and epoxy spray paint finishing for making it durable. Overall size of shelf is 1.80m(L) x 0.60m(B) x 2.10m(H) |
| 14 | OD54007/2026-2027 - Supplying executive type high back chair with headrest of size and details as follows.BACK SIZE: 51.8(W) X 53.5cm (H) *SEAT SIZE: 51.8cm (W) X 51.8cm (D). Full height of chair with headrest 123cm. Approved make of materials: Godrej/ Featherlite/ Herman Miller1. SEAT / BACK: The seat sub-assembly is made up of 1.2±0.1cm thick Plywood,upholstered with polyester fabric over moulded foam and covered with an injection moulded polypropylene outer cover. The seat can be manually tipped-up when not in use. The back sub- assembly is made up of injection-moulded glass filled polypropylene inner upholstered with polyester fabric over moulded foam and covered with an injection-moulded polypropylene outer cover. Both these subassemblies are fixed to the tubular structure.2. ARMRESTS: The armrest top should be molded from polyurethane (PU) and mounted onto a drop lift adjustable type tubular armrest support made of 03.81±0.03 cm x 0.2±0.01 cm thk M.S. E.R.W tube having chrome plated finish. The armrest height adjustable up to 6.5±0.5cm in 5 steps.3. ACTIVE BIO-SYNCHRO MECHANISM: The adjustable tilting mechanism should be designed with the following features:-360° revolving type -Front pivot for tilt with feet resting on ground and continuous lumbar support ensuring more comfort -Tilt tension adjustment can be operated in seating position -5-position Tilt limiter giving option of variable tilt angle to the chair -Seat/back tilting ratio of 1: 2 -Themechanism housing should be made up of HPDC Aluminum black powder coated4.SEAT DEPTH ADJUSTMENT: Seat depth adjustment should be integrated in the seat through a sliding mechanism. Seat depth adjustment range should be of 6.0±0.5cmADJUSTABLE BACK SUPPORT: Back Frame should be connected to the Up/Dn mechanism housed in Plastic T spine. It can be adjusted in the range of 7.42±0.5 cm for the comfortable back support to suit individual need5.PNEUMATIC HT. ADJUSTMENT: The pneumatic ht adjustment has an adjustment stroke of 10.0±0.3 cm6.PEDESTAL ASSEMBLY: The pedestal should be High Pressure Die cast polished Aluminum and fitted with 5 nos. twin wheel castors. The pedestal should be 65.0 ± 0.5cm. pitch-center dia. (75.0 ± 1.0cm. With castors.)TWIN WHEEL CASTORS: The twin wheel castors should be injection molded in black PP having 6.0± 0.1cm wheel Diameter. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 25, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 06, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 6 daysAug 10, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 10 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender