Tender For Replacement Of 2 Nos. Flap Shutter & 3 Nos. Draw Shutter, Improvement Of Hoisting Arrangement Including Ss Lining Embedded Frame And Painting, Cross Bandth At Sarda, Bainan & Nearby Localities, Block -Amta Ii, P.S- Amta, Dist. Howrah.
Tender Value
1.92 Lakhs
Estimated cost
Bid Submission
03 Aug 2026
6 days left
EMD
3842
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Howrah → West Bengal
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Replacement Of 2 Nos. Flap Shutter & 3 Nos. Draw Shutter, Improvement Of Hoisting Arrangement Including Ss Lining Embedded Frame And Painting, Cross Bandth At Sarda, Bainan & Nearby Localities, Block -Amta Ii, P.S- Amta, Dist. Howrah.
BOQ
| Sl. No. | Item Description |
| 1 | Taking out flap shutter of sluice gate including hoisting arrangement and refitting the same with new nut and blots where necessary. |
| 2 | Up to 4.00 sq.m., Taking out and refitting the same. |
| 3 | Up to 4.00 sq.m., Taking out only. |
| 4 | Fabrication , Supply, erection and commissioning of new Slide type vertical lift regulator service gates of Canal/River as per IS: 5620 - 2000/Latest Revision consisting of skin plate, vertical and horizantal grider, stiffener etc. made of MS material consisting of angle , channel, beam, plate, flat, etc. conforming to IS : 2062 -2011/latest revision manufactured as per approved drawing and direction including cost of Materials, Machinaries , Manpower, Cutting, Aligning, drilling, Welding, Finishing, Consumables,Carriages and all overheads with all leads and lifts complete as per specification (without painting). Width of Gate shutter size upto 2 metre. |
| 5 | Cost for repairing of vertical/flap gate shutter of canal/river including dismantling the damaged portion at lower part (skin plate, horizental/ vertical girder/stifner etc as per IS : 2062 - 2011 /latest revision) not more than 25% of gate hight from bottom by gas cutting and fitting, fixing and fabricated by welding as per direction including cost of Materials, Machinaries , Manpower, Cutting, ligning, nchoring, Welding, Finishing, Consumables, Carriage and all overheads with all leads and lifts complete as per specification (without painting) Width of Gate shuteer size upto 2 metre |
| 6 | Cost for supplying and fitting fixing of angle type rubber seal (Make : Universal Moulders &Engineer/Popular Rubber Works (Pvt) Ltd/SAB Industries/Unique Polymer Works/equivelant approved make conforming to lS : 11855 -2011/Latest Revision) for different types of gate shutter as per direction of E.I.C. The cost includes cost of man power employed for fitting fixing, cost of rubber seal, hire charges of tools & tackles, scaffolding and safety equipments etc including carriage loading & unloading but excluding supply of ms clamp/ flat plate,bolts, nuts and washer. |
| 7 | Size (88 mm +60 mm+08 mm) x 14 mm thick |
| 8 | Fabrication, supply, erection and commissioning of embeded parts consisting of hinge bracket with its accessories for vertical flap gateshutter of distributories/ branchcanal/ minor anal/channel made of MSmaterial consisting of angle,channel, beam, plate, flat, etc. conformingto IS : 2062 -2011/latest revision manufactured as per approved drawing and direction of Engineer in charge. The cost includes cost of Materials, Machinaries , Manpower, Cutting, Aligning, Anchoring,Welding, Finishing, Consumables, Carriage and all overheads with all leads and lifts complete as per specification (without painting). |
| 9 | Holding down bolt with nut including 100 x 100 x 6 mm plate washer at bottom fitted complete and packing the hole with cement concrete or cement grout as directed.16 mm dia bolt. 300 mm long |
| 10 | Supply of Structural M.S Bolt/Nut/Washer (Hot dipped Galvanised) |
| 11 | Oiling greasing of headstock assembly (for screw hoist system) of regulator gates of canal/ river by cleaning, checking, greasing, screw rod, G.M nut, Thrust bearing , guide channel, etc including all charges of man & materials which include refilling of gear oil, oiling,greasing and fixing of missing nut & bolts & oil seals etc to complete the job as per direction of EIC. |
| 12 | Surface cleaning of metal surfaces by chemical cleaners and then by hand with emary paper,wire brush and power tool cleaners and removing dust and preparation o f surface including cost of all materials, labour, achinery, scaffolding, etc., complete with initial lead for sand upto 1 km and all lifts. |
| 13 | Painting of embedded parts, all types of gates, stoplogs and barscreen/gratings etc on prepared surfaces with one coat of inorganic zinc silicate primer (airless s p r a y preferred)70+/ - 5 micron and two super coats with a total thickness of 300 microns (each 150+/- 5) of solventless coaltar epoxy paint each coat 150 microns ( total 300 microns) including cost of all materials, labour, scaffolding etc., complete with all leads and all lifts |
| 14 | Painting hoist structural components, tressle bridge ,crane, lifting beam, cat work bridge and other similar structure on prepared surfaces with two coats of zinc phosphate primer (airless spray preferred) 40 microns/coat and followed by two coats of synthetic enamel paint 25 microns/coat including cost of all materials, labour, scaffolding etc., complete with all leads and all lifts. |
| 15 | Cross Bandth :-Supply of empty cement polythene bags in good condition including stacking and carraige cost to site, labour charge for filling gunny bags/polythene bags with all kinds of earth or sand wet or dry including sewing mouth and stacking within a lead of 150 Mtr. and all lifts as per direction of the engineer in charge (Filled up weight not less than 30 kg.)(Measurement to be taken up in stacks), labour charge for dumping filled up gunny bags/Polythene bags in standing or flowing water with or without boats inclusive of placing in position with all leads and lifts complete as per direction of E.I.C. |
| 16 | Supplying to site empty cement polythene bags (capacity 50 kg) in good condition including stacking, incedental charges etc. all complete ( capacity 50 kg) |
| 17 | Labour charge forfilling empty cement gunny bag / polythene bag (capacity 50kg) with all kinds of earth (wet or dry), sand or agreegates (stone/ brick) and sewing as done in case of cement bag,( typing with a knot after filling will not be accepted), and staking within a lead of 30 metre as per direction of E.I.C.( cost is excluding the cost pf any types of filling materials) |
| 18 | Damping in position are sand filled gunny / polybags ( capacity 50 kg) within a lead of 30 metre inclusive of all lifts. |
| 19 | Removing earth/sand filled poly bags/gunny bags from the channel bed/slope and initially depositing the same near channel bank at bed/slope and initially depositing the same near channel bank at a place as directed by the enginner - in charge for measurement of bag & then disposing off the same at a distance not less than 150 metre from the channel site. |
| 20 | Bailing out water by pump including all leads and lifts and including making all arrangements for disposal, where continuous flow or seepage of water is encountered and rating of pumps and hours of operation is specifically ascertained as per direction of the Engineer-in-charge |
| 21 | Fabrication , supply, erection and commissioning of embeded parts consisting of seal beam, Guide channel with all accessories for vertical gate of canal/river made of MS material consisting of angle, channel, beam, plate, flat, etc. conforming to IS : 2062 2011/latest revision manufactured as per approved drawing and direction including cost of Materials, Machinaries , Manpower, Cutting, Aligning, Anchoring, Welding,Finishing, Consumables, Carriage and all overheads with all leads and lifts complete asper specification (without painting). |
| 22 | Seal beam |
| 23 | Dismantling all types of plain cement concrete works, stacking serviceable materials at site and removing rubbish as directed within a lead of 75m In ground floor including roof above 150 mm. thick |
| 24 | Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, in ground floor as per relevent IS code.Pakur varity |
| 25 | Supplying, fitting & fixing of M.S fabricated pedestal stool of suitable size, consisting of bottom plate, top plate, four nos legs etc febricated with suitable sizes m.s plate, m.s angle conforming to I.S 2062 of latest revision and as per approved drawing & direction of Engineer in charge. The cost includes cost of materials, man power employed for dismantling and fitting fixing, civil works consumables like cutting tools, gas, oxygen, welding rod, anchor bolt of required size, hire charges of machineries, like gas cutting set, welding set, tools & tackles etc including carriage loading & unloading. |
| 26 | Supply and fabrication of new stainless steel plate/flat (AISI ‐ 304) of suitable size on seal beam / roller track/ slide track/ side seal seats/ top seal seat by welding (SS) as per direction of the Engineer‐in‐charge including cost of Materials, Machinaries , Manpower, Cutting,Aligning, Welding, Finishing, Consumables, Carriage and all overheads with all leads and lifts complete as per specification. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 25, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 03, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 6 daysAug 03, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 6 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender