Tender For Addition Alteration To Transit Facility & Certain Minor Works Under Age B/R I At Chandimandi
Tender Value
46.72 Lakhs
Estimated cost
Bid Submission
15 Aug 2026
14 days left
EMD
93440
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Panchkula → Haryana
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Addition Alteration To Transit Facility & Certain Minor Works Under Age B/R I At Chandimandi
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of brick work built in cement mortar including all quoins, arches, pillar etc complete all as specified and directed. |
| 2 | Brick work with sub class ‘B’ bricks of old size bricks, straight or curved on plan exc 6 metre mean radius built in cement mortar 1:4 complete all as specified & directed. |
| 3 | Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified and as directed. |
| 4 | Dubbing out average 15 mm thick with cement plaster (1:4) with & incl chicken wire mesh on irregular faces of walls/RCC surfaces (Roof, Chajja, Facia etc) complete all as specified and directed. |
| 5 | Repair to RCC sunshades, chajjas, balconies, columns, bands, beams and similar RCC work at any position / height by dismantling loose / disintegrated portion including necessary scaffolding and safety arrangements and fixing of reinforcement (cut to length, bent to shape required, including cranking, bending spirally including mild steel wire (annealed) not less than 0.9 mm dia and chicken wire mesh of size 12.5mm x 1mm securing with clips)/ chicken wire mesh wherever required and dubbing out with cement concrete 1:1.5:3, 15mm to 50mm thick as required on site, using 6 to 12mm graded stone aggregate to make up and finished the required shape including provision of necessary scaffolding and formwork up to 04 storey bldg if required and finished with 5mm thick rendering in cement mortar 1:4 finished even and fair without using extra cement complete all as specified and directed. (NOTE : Supply only chicken wire mesh will be measured and paid separately under respective items) |
| 6 | Supply only chicken wire mesh of size 12.5mm x 1mm, complete all as specfied and directed |
| 7 | Taking down cement plaster on brick/stone walls etc including raking out joints, hacking for key scrubbing down with water etc complete all as specified and directed |
| 8 | 15mm thick rendering cement plaster in Cement mortar 1:6 over brick or concrete surfaces finished even and smooth without using extra cement and providing necessary scaffolding , safety precautions and other requisite arrangements complete all as specified and directed |
| 9 | 15mm thick plaster in cement mortar 1:4 on fair faces of brick wall or on concrete surfaces and finishing the surface fair and even without using extra cement and providing necessary scaffolding , safety precautions and other requisite arrangements all as per site requirement, complete all as specified & directed. |
| 10 | Applying Two or more coats on new plastered surfaces of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all as specified and directed. |
| 11 | 5mm thick rendering on ceiling surfaces in CM 1:3 over brick work or concrete surfaces finished even and smooth without using extra cement, as in ceiling, chajjas, facias, at any position, complete all as specified and directed. |
| 12 | Complete removal of existing treatment by scrapping of walls, chajjas, ceilings, fins, facias etc. by mechanical means like mechanical sander etc. with internal dust extraction system including expose sound substrata for further surface preparation prior to painting work all as directed by Engineer-in-Charge |
| 13 | Applying a layer of 1-2 mm thick wall care putty on new/old surface of wall/ceiling all as specified and directed by Engr-in-Charge |
| 14 | Applying 2 coats of modified acrylic Interior emulsion paint over new/old decorated surface having excellent scrub and peel resistance, superior whiteness, excellent finish, resistance to fading of colours, advanced anti fungal and algal protection against all round weather so as to obtain an acceptable finish and paint performance of min. 4 Years, complete all as per manufacturer's instruction and directed by Engineer-in-Charge |
| 15 | Applying two coats of oil bound distemper on ceiling surface after preparation over and including one coat of primer, complete all as specified and directed |
| 16 | Applying 2 coats of modified acrylic exterior emulsion paint over new/old decorated surface having excellent scrub and peel resistance, superior whiteness, excellent finish, resistance to fading of colours, advanced anti fungal and algal protection against all round weather so as to obtain an acceptable finish and paint performance of Min. 4 Years, complete all as per manufacturer's instruction and directed by Engineer-in-Charge |
| 17 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed. |
| 18 | Glazed coloured ceramic tiles on vertical surface 1200x600x9-10 mm thick , joint free, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile over and incl 10 mm thick rendering in CM 1:4, complete all as specified and directed. |
| 19 | Non - skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match in white or coloured cement to match the shade of tile, over & incl screed bed or bedding layer 15 mm thick in CM 1:6, complete all as specified and directed. |
| 20 | Vitrified Ceramic tiles light shade 8-9 mm thick First quality (square/ rectagular) polished, area of each tiles not exceeding 0.36 sqm , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & incl screed bed or bedding layer 15 mm thick in CM 1:6 complete all as specified and directed. |
| 21 | All as per item no 20 above but on vertical surface, complete all as specified and directed. |
| 22 | Dismantling of boarding any description fixed in any position fixed with screws complete all as specified and directed |
| 23 | Powder coated Gl frame work grid 605x 605mm for false ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to entre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre and hangers 3mm dia GI (up to 1200mm length )adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40x3 mm size 60mm long and expansion hold fasteners 12.5mm dia ,40mm long complete all as specified and directed. |
| 24 | 4mm thick non asbestos fibre cement building boards fixed or laid /inserted to timper /GI/Aluminium frame work with screws fixed in ceiling flat or sloping complete all as specified and directed. |
| 25 | Solid PVC Wall lining consisting of 5mm thick plain colour PVC Sheet as per specification drawing but wood grain printed PVC sheet used instead of plain colour sheet including fixing items complete all as specified and directed. |
| 26 | 18 mm thick HDHMR Board for Cup board and shutters prelaminated both side as per approved design manufactured from hardwood and having uniform density gradient & compact core with density over 650 kg/m3, complete all as specified and directed by Engineer-in-charge. |
| 27 | Magnetic cathcher for kitchen cabinet/ cupboard fixed in repair as complete all as specified and as directed. |
| 28 | 1.5mm thick scratch proof high gloss Acrylic sheet, to be pasted on front shutters of HDHMR board, complete all as specified and directed by Engineer-in-charge. |
| 29 | 20mm wide & 1mm thick PVC edge beading of PVC to be pasted on edges with suitable adhesive, complete all as specified and directed. |
| 30 | Food grade stainless steel wire in any baskets of a modular kitchen (storage basket, cup and saucer basket, jas basket, thali basket, cutlery basket, grain trolley , plain basket, bottle pull out etc), minimum loading capacity 65 Kg, made by min 6 mm dia stainless steel round bars, proper welded and joints finish by grinding, chromium plated finish, fixed properly with WPC board of any thickness as per design approved, including fixing of auto closing hinges, ball bearing runners of any description, stainless steel handles fixing clips, sliding frame structure, SS screw etc complete all as specified and directed by Engineer-in-charge.Note:1. Only weight of SS wire basket will be measured before fixing.2. Only Fixing of all Fitting/fixtures like handles, hinges, ball bearing runners, telescopic channels etc are included and for material will be paid in separate items as supply only. |
| 31 | Supply only of soft auto closing hinges openable at 0 degree for kitchen cabinet shutters Make :Hettich/ Ebco/ Primer |
| 32 | Supply only Ball bearing runners 45 mm soft closing Telescopic Channel (20 Inch) full extension load capacity 50 Kgs, Black powder coated, Make :Hettich/ Ebco/ Primer |
| 33 | Metal profile section for each shutter in kitchen cabinets either below or above slab complete all as specified. |
| 34 | Handmade double bowl Sink of single bowl size 410 x 330 x 160 mm complete all as specified. |
| 35 | Continuos piano hinges, mild steel bright finish width of flap 30mm as fixed in repair, complete all as specified and as directed. |
| 36 | Taking down chowkhat n.exc 1.5 sqm each with or without taking off shutter and removing from site complete all as specified and as directed. |
| 37 | Taking down chowkhat exc 1.5 sqm each but not exc 4.00 sqm with or without taking off shutter and removing from site complete all as specified and as directed. |
| 38 | Taking down shutter exc 1sqm but n.exc 2 sqm each & removing from site complete all as specified and as directed. |
| 39 | Taking down shutter, resecuring or easing & adjusting in Same opening of any description exc 1 sq m and n exc 2 sq m complete all as specified and as directed. |
| 40 | Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 50 x 100 mm and 45 x 85mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately) Complete all as specified as per Manufacturer broucher. MAKE: RAJSHREE, SINTEX, ECOCELL OR EQUIVALENT. |
| 41 | Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. MAKE : RAJSHREE, SINTAX, ECOCELL OR EQUIVALENT. |
| 42 | 125mmx60mm Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc. including filling of cement concrete 1:3:6 type C1 in frame, complete all as specified and as directed. |
| 43 | 105 x 60mm Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc. including filling of cement concrete 1:3:6 type C1 in frame complete all as specified and as directed. |
| 44 | Cement concrete 1:2:4 Type B 1 (using 20 mm graded aggregate) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, back fill of chowkhat, plinth courses, string courses, lacing courses, parapets and railings upto 60cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in Item 4028, water trought and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed. |
| 45 | Fibre glass reinforced 35mm thick door of any design and any pattern fixing with hinges panels will be costructed of two sheets of 1.20mm fibre glass sheet bounded to 3/4 inch core matrlpanel thickness will be 25mm an aluminium frame surrounds the perimetre of the panel and measures and approved design including complete fitting handle, tower bolt, door stopper all complete as per requirement and direction of Engineerin- charge. |
| 46 | 35mm 2nd class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and as directed. |
| 47 | 50mm stainless steel barrel tower bolt (ISI Marked) of extruded section complete all as specified and directed |
| 48 | 100mm stainless steel barrel tower bolt (ISI Marked) of extruded section complete all as specified and directed |
| 49 | Stainless steel sliding door bolt (ISI Marked) 250mm long hasp , staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminum alloy. |
| 50 | 100 mm size but hinges ,stainless steel with galvanised mild steel hinge pin complete all as specified and as directed. |
| 51 | 100mm size stainless steel handle fancy type (ISI Marked) extruded type anodized, complete all as specified and directed. |
| 52 | 150mm size stainless steel handle (ISI Marked) extruded type anodized, complete all as specified and directed. |
| 53 | Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge.Note:- (I) Thickness of powder coatings shall be not less than 30 micron.(ii) Weight of the aluminiumnsections only shall be measured and paid.(iii) Aluminium doors window/ ventilators to be fixed to jambs with cadmium plate screws.(iv) The rate shall be inclusive of neoprene beadings, handles, hinges, screws etc. weight of fittings/fixtures will not be measured for ariving the weight of aluminium section.(v) Glass panes and panels shall be measured & paid separately under respective items. Design shall be approved from Engineer-in Charge as existing at sitebefore fabrication and bulk order to the manufacturer. |
| 54 | Powder coated aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified all complete as per architectural drawings and the directions of Engineer-in-charge. |
| 55 | 4.80mm thick ordinary quality tinted glass, fixed to frame work not exc 0.5 Sqm in each pane, complete all as specified & directed. |
| 56 | 4.80mm thick ordinary quality tinted glass, fixed to frame work exc 0.5 Sqm in each pane, complete all as specified & directed. |
| 57 | 3mm thick Sheet glass, ordinary quality n exc 0.5 sq. m in each pane including hacking out old broken glass (any thickness, size, quality or description) from wooden/steel frames , concrete or brick surrounds, with necessary fixing arrangements complete all as specified and as directed.. |
| 58 | All as per item No 57 above but 4mm thick tinted / frosted sheet glass area n exc 0.5 Sqm fixed to frame work complete all as specified & directed. |
| 59 | Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm including fixed with stainless steel wire staples fixed in repair complete all as specified & directed. |
| 60 | Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm including fixed with stainless steel wire staples complete all as specified & directed. |
| 61 | Preparation of new wooden surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed. |
| 62 | Preparation of new steel surfaces exc 10cm width or girth and applying two coats of synthetic enamel paint over and including one coat of red oxide primer complete all as specified and as directed. |
| 63 | Preparation of old wooden surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed. |
| 64 | Preparation of old steel surfaces of any description over 10cm width or girth and applying one coat of synthetic enameled paint complete all as specified & directed. |
| 65 | 140mm Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor and in repair complete all as specified and directed. |
| 66 | Pillar tap 15mm dia cast copper alloy fancy type with capstain heads, chromium plated, screwed down high pressure with or with out lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, fancy type, fixed in repair complete all as specified and directed. |
| 67 | 15mm bore angle valves, cast copper alloy, fancy type chromium plated, screwed pressure, with crutch of butterfly handle, screwed both ends for iron pipe for unions, fixed in repair and all as specified and directed.MAKE. JAQUAR FUS-29053 or equivalent make as approved by GE |
| 68 | 15mm bore Bib taps, cast copper ally, fancy type chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed as in repair all as specified and directed. MAKE. JAQUAR FUS-29037 or equivalent make as approved by G |
| 69 | Taking up or down steel tubing and connections 15mm bore, including cleaning for refixing or removal to store complete all as specified and directed |
| 70 | Taking up or down steel tubing and connections 20mm bore, including cleaning for refixing or removal to store complete all as specified and directed |
| 71 | 15mm bore tubes “medium grade”, galvanized, with and including all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and directed. |
| 72 | 20mm bore tubes “medium grade”, galvanized, with and including all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and directed. |
| 73 | Decorated fancy type vanity with storage space, min size of 750mm x 500mm with counter top wash hand basin , fancy type Pillar cock, waste coupling and waste pipe suitable for the design and quality approved by Engr-in-Charge complete all as specified and as directed. |
| 74 | Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified. fixed as ijn repair complete all as specified and directed. |
| 75 | Wall/sink Mixer, mixer for mixing hot & cold water screwed down for iron pipe and fixed, suitable for 15mm bore pipe, fixed as in repair, complete all as specified and as directed MAKE. JAQUARVGP-81149 or equivalent make as approved by G |
| 76 | WHB Mixer, central hole mixer for mixing hot & cold water screwed down for iron pipe and fixed, suitable for 15mm bore pipe, fixed as in repair, complete all as specified and as directed MAKE. JAQUAR FON-40005B or equivalent make as approved by G |
| 77 | Vitreous china wash hand basin, white, flat back, size 415X415X145MM including brackets of suitable size, complete all as specified and directed. MAKE .JAQUARJDS-BLM-25907N or equivalent make as approved by G |
| 78 | Bath cabinet of size 600mm x 450mm fixed to wall with rawl plugs having arrangements to put inside toiletries, fixed as in repairs complete all as specified and directed. |
| 79 | Towel rail 600mm long of chromium plated fixed with and including chromium plated screws and wooden / plastic cleats (minimum weight 190gms), fixed as in repair complete all as specified and directed. |
| 80 | S&F in repair of brass chromium plated shower rose, 125mm size with long swivel plush CP arm complete all as specified . |
| 81 | Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long, fixed as in repair, complete all as specified . |
| 82 | Corner glass shelf assembly 5.5 mm thick toughened glass 300x300mm wide bevelled edge/ hatching of edges fixed with stainless steel \\"D\\" brackets with railing, fixed as in repair complete all as specified and directed. |
| 83 | 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls/floor including taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning complete all as specified and directed. |
| 84 | S&F in repair 110 mm bore PVC (SWR) bends of any radius complete all as specified and directed |
| 85 | 75 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls/floor including taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaningcomplete all as specified and directed.complete all as specified and directed. |
| 86 | S&F in repair 75 mm bore PVC (SWR) bends of any radius complete all as specified and directed |
| 87 | Demolition of stone slabs of any description in floors laid, bedded and pointed in any mortar complete all as specified and directed |
| 88 | 18-20mm tick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and laid over 15mm thick screed in CM 1:6 complete all as specified and directed |
| 89 | Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations, complete all as specified and directe |
| 90 | 500 litres capacity rotational moulded polyethylene water storage tanks white in colour (Cylindrical vertical with closed top) Three layered, screwable lid, hoisted and fixed in position, including supply and fix tank nipple, ball valve 20mm PTMT, including dismantling of existing water tanks and removing from site all as specified in SSR Part-I and all as directed |
| 91 | 1000 litres capacity rotational moulded polyethylene water storage tanks white in colour (Cylindrical vertical with closed top) Three layered, screwable lid, hoisted and fixed in position, including supply and fix tank nipple, ball valve 20mm PTMT, including dismantling of existing water tanks and removing from site all as specified in SSR Part-I and all as directed |
| 92 | S&F in repair PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and as directed. |
| 93 | Vitreous China wash down Single piece EWC water closet pan alongwith cistern (pedestal pattern), white (with all fittings) including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe, etc.in repair complete all as specified and directed by Engr-in-charge. Make Jaquar cat part No.FNSWHT-40751P180UFSMZ complete all as specified and directe |
| 94 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed. |
| 95 | Mild steel framed work as in chajjas, or ladders gates of angles or other sections with gusset plates, ladders, complete drilled for fixing of steel sheeting or other covering. Doors etc to be prepared for hanging or sliding with including hooks and hinges (excluding of covering steel sheeting) fastening, locking arrangement, etc conforming to Fe 410-W (Gde E- 165) complete all as specified and directed. |
| 96 | Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws incl dismantling of Asbestos cement (corrugated, semicorrugated sheets) from roof coverings complete all as specified and directed. |
| 97 | Rolled sections as in main and cross beams, coloumns , hip and jack rafters; purlins where connected to common rafters of angle , pipe sections etc Fe 410 Gde 250 quality B complete all as specified and as directed |
| 98 | Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of inserting sheets, landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and as directed |
| 99 | Demolition of cement concrete (unreinforced) of any description and in any position (below or above GL at any ht) not otherwise specifically provide for complete all as specified and directed. |
| 100 | 75mm thick Cement concrete type C2, (1:3:6) (using 40mm graded aggregate) as in Plinth protection finished the concrete surface even and smooth without using extra cement, 10mm construction joint will be provided and Panel should not be more than 3 m in length and joint filled with filler bitumen and sand in ratio (1:3) complete all as specified and directed. |
| 101 | Cement concrete 1:4:8, type D2 (40mm graded stone aggregate) for 75mm thick floor as in sub base for tiles over and incl Screed bed or bedding layer in CM 1:6 , 20 mm thick for laying floor to receive tiles complete all as specified and directed. |
| 102 | Factory made rubber moulded machine pressed coloured Endura cement concrete tiles 3000mm x 300mm x 10mm thick (with grey cement and no pigments), set, jointed and pointed in neat cement slurry with grey cement with pigment to match the colour of tiles, glossy finish, laid complete all as specified and directed. |
| 103 | Cement concrete 1:2:4 Type B 1 (using 20 mm graded aggregate) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in Item 4028, water trought and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed. |
| 104 | Ist class hard wood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified and directed. |
| 105 | 25mm dia stainless steel , fancy type disigner rods with fixing brackets, stops, end rollers etc. for curtain rod including taking down defective bracket all as specified and as directed. |
| 106 | Rreinforced cement concrete 1:2:4 type B1 (using 20 mm graded stone aggregate ) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified & directed. |
| 107 | Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar works not exceeding 200mm thick (Horizontal or sloping) for rough finish surface of concrete, complete all as specified & directed. |
| 108 | Mild steel TMT bars 10mm dia & over, cut to length, bent to shape reqd including cranking, bending specially for columns, hooking ends & binding with MS wire annealed not less than 0.9 mm dia welding as required at site as directed and specified etc complete. |
| 109 | Roof treatment with water proofing compound as follows, complete all as specified and directed. Make: Pidilite/ Fosroc/Asian, Entire work will be divided into following stages as under and will be certified by a technical rep of company whether the stages completed are as per manufacturer’s instruction and finally passed by Engr-in-Charge/GE:- |
| 110 | Surface Preparation:Clean RCC slab using electric wire cup grinder to remove surface imperfections, sharp edges or protrusions at the junctions to achieve a uniform surface profile. Thoroughly clean the concrete surface using a high-pressure water jet to eliminate all dirt, dust, oil spillages, laitance, and other contaminants.Surface Crack Repair:Cracks on RCC slab wider than 1mm required to be cut and open in V-groove manner (8 mm wide × 6 mm deep) by using mechanical cutter, clean the same and fill with Feviseal HY 300 hybrid sealant. Allow sealant to air cure for 3 days. |
| 111 | Angel Fillet treatment:Providing and preparing angel filet at all vertical up-stands & junctions /Corners. Moist the surface with water, apply bond coat prepared by mixing Dr. Fixit Pidicrete URP and cement (1:1) by volume and apply using brush, preparing PMM by mixing 1 kg Dr. Fixit Pidicrete URP, 5 kg fresh cement, and 15 kg graded quartz sand. (i.e., in the ratio of 1:5:15) and preparing angle fillet (Gola) of size 50 x 50mm over wet the bond coat and finishing the same followed by moist curing the surface for 48-72 hours etc. complete.Rainwater outlets treatment: Hacking and chipping the surface around the rainwater drain outlet up to 25mm in depth. Apply bond coat of Universal Repair Polymer (URP) in the ratio of 1:1 (URP 1: Cement 1) by volume over the corners and pipe insert outlet gaps. Filling the gaps around drain mouth with (PMM) polymer modified mortar mixed with Universal Repair Polymer (URP) 10% by weight of cement in the ratio of 1:3. Providing & fixing 100 mm width 225-gsm g/m2 Fiberglass Chopped Strand Mat around the periphery of drain mouth of rainwater outlet sandwiched with Two Component UV resistant hybrid uretherane elastomeric waterproof top coat. Apply two thick coats of Two Component UV resistant hybrid uretherane elastomeric waterproof coating to completely cover the mesh/fabric and surrounding area. Make of Two Component UV resistant hybrid uretherane elastomeric waterproof: Dr Fixit Wonderproof 100, Fosroc, STP & Make of URP: Dr Fixit Pidicrete, Fosroc Conplast, SIKA |
| 112 | Waterproofing Application:Premix Dr. Fixit Wonderproof 100 Components A and B using an electric double-paddle mixer at low speed for 2-3 minutes until a uniform blend is achieved, without dilution. Apply the waterproof coating on an SSD (Saturated Surface Dry) condition. Apply first coat of Dr. Fixit Wonderproof 100 at a rate of 0.80-0.90 kg/m using a lamb's wool roller. While the coating is still wet, roll and embed a 225 gm Fiberglass Chopped Strand Mat, ensuring full bonding without air bubbles or wrinkles, and overlap joints by at least 5 cm at endpoints. Allow the first coat to dry for 3-4 hours. Apply the second coat at a 90° angle to the first coat at 0.90 kg/m once the surface is dry enough to walk on. Additional coats may be applied as required to achieve a forced material consumption to obtain a DFT of 1000-1200 microns, with minimum material consumption of 1.80 kg/m over 2-3 undiluted coats. The coating should terminate below the drip mold on vertical surfaces. The system complies achieving: Tensile Strength: 215 N/mm-as per (ASTM D2370-2016), Tear Strength: 2100 N/mm as per (ASTM D 624), Dynamic Crack Bridging (EN 13251:2016), Shore A Hardness: 85, Zero Water Permeability: at 15bar as per (EN 12390-8:2019), Passes Water Migration Resistance: No leakage, Low Temperature Flexibility: -20°C after 1000 hrs. UV (ASTM D1970-2021), Solar Reflectance Index: 90 (ASTM E1980 for white). Peel Adhesion to Concrete (Wet Condition, 24 hrs.): ASTM C794-12, Root resistant according to CEN/TS 14416-2014, The system confirms compliance with EN 13251:2016 for a 25-year service life when used with a 225-gsm fiberglass mat. It is backed by a 10-year waterproofing warranty from the manufacturer. |
| 113 | Note : (i) Authorised applicator of the company with trained/ skilled workers will only be allowed to execute the work and the applicator will submit the authorization and experience certificate from the company.(ii) The entire quantity of material will be calculated and brought on site as decided by Engr-in-Charge and will be accepted only post verification of PVs and Challan from the company through Mail. (iii) Material will be kept in the custody of MES rep and will be issued to the authorised applicator as per requirement(iv) Each stage will be properly executed with the supervison of company rep and Stage passing register will be properly maintained accordingly.(v) The contractor shall submit manufacturer generated 10 years warranty card during submission of RAR and Final Bill (vi) A guaranty amount @ 10% will be kept as reserve till completion of warranty period and will be released thereafter. (vii) Any deterioration during the warranty period will be rectified by the manufacturer without any financial effect. (viii) Ponding test shall be carried out for 72 Hrs after completion of roof treatment and ponding shall be done by applicator with company technical rep as per manufacturer’s instruction and finally passed/ directed by Engr-in-Charge/GE. |
| 114 | Steel work in tubular trusses including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS-1161-1979 grade St-240, including shop coat of zinc chrome red oxide primer complete all as specified and directed. |
| 115 | Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. complete all as specified and directed. |
| 116 | Point wiring with approved colour code multi stranded copper conductor, PVC insulated and unsheathed FRLSH cable of size 1.5 Sqmm ,1100 volts grade, two run of single core cable for phase & neutral and one run of single core multi stranded copper conductor, PVC insulated and unsheathed FRLSH cable of size 1.5 Sqmm ,1100 volts grade for earth continuity conductor to common earth and connected to earth dolly in and including new concealed rigid non metallic PVC conduit of suitable size but not less than 20 mm dia and including new modular sunken box and suitable size of frame, cover for mounting switch, socket and regulator fixed on surface flush with wall , comprising of One light /bell/buzzer point controlled by one switch or one fan point controlled by one switch &fan regulator, complete all as specified and directed. Note : Unit rate is inclusive of making good the disturbed surfaces by provding by wall putty/POP after mason work and finshing to match the original and nothing extra shall be paid on this account. Note :Unit rate is inclusive of cutting chases in wall /foor/PCC and making good the disturbed surfaces to match the original and nothing extra shall be paid on this account. |
| 117 | All as per serial item 116 herein before but for socket outlet 3 pin 5 Amps on same board complete all as specified and directed |
| 118 | All as per serial item 116 herein before but for socket outlet 3 pin 6 Amps on independent board complete all as specified and directed |
| 119 | All as per serial item 116 herein before but One socket outlet three pin ,6/16 Amp, independent board, with 2.5 Sqmm (nominal area ) FRLSH cable & 2.5 Sqmm (nominal area ) cable as earth continuity conductor, complete all as specified and directed |
| 120 | Modular switch (ISI marked), single pole, one way 6 Amps, one module (ISI marked), complete all as specified & directed. |
| 121 | Modular switch type bell push, 6 amp, single pole, 230 volt one module,(ISI marked) complete all as specified and directed. |
| 122 | Switch modular type (ISI marked), single pole, two way, 6 Amps, one module (ISI marked), complete all as specified & directed. |
| 123 | Switch modular type (ISI marked), single pole, one way, 16 Amps, one module (ISI marked), complete all as specified & directed. |
| 124 | Socket shutters outlet 2/3 pin 6 Amp modular type multi purpose two module (ISI marked), complete all as specified & directed. |
| 125 | Socket shutters outlet 2 in 1 pin 6/16 Amp modular type multi purpose combined 2 module (ISI marked), complete all as specified & directed. |
| 126 | Modular switch type stepped fan regulator, single pole, 230 volt two module complete all as specified and directed. |
| 127 | Electric Bell, multi music type, AC, 230 volts, single pole all as specified and directed by Engineer-in-charge. |
| 128 | Ceiling rose, PVC or polycarbonate of size 65mmx50mm three terminals (ISI marked) all as specified and directed by Engineer-in-charge. |
| 129 | Lamp holder, PVC/Polycarbonate type with back plate modular type fixed on wall suitable for batten fitting ,complete all as specified and directed. |
| 130 | LED Bulb 09 watt self ballasted Retrofit type lamp with PBT body shell and DC diffuser CCT 6500 K complete all as specified and directed. |
| 131 | LED Lights fitting 1 x 18/20 Watt, 4 feet ,220V AC decorative type including fitting fixed on wall/ceiling and connecting up complete with flexible cable white of suitable size and making necessary connection fixed as in repair complete all as specified and directed. |
| 132 | LED sleek modern wall light fitting 24 watt, 220 V AC, scene switch type cool/warm white of approx size 868 x 93 x 33 mm, polycarbonate body, decorative/modern incl fitting fixed on wall/ceiling and connecting up complete with flexible cable white of suitable size and making necessary connection, complete all as specified and directed. |
| 133 | LED Mirror Lights fitting 12 watt cool/ warm white, 220V AC decorative adjustable/rotational type, approx 500 mm length and connecting up complete with flexible cable white of suitable size and making necessary connection f |
| 134 | LED Mirror Lights fitting 17 watt cool/ warm white of approx size 534 x 93 x 33 mm , 220V AC decorative/model including fitting fixed on wall/ceiling and connecting up complete with flexible cable white of suitable size and making necessary connection fixed as in repair complete all as specified and directed. |
| 135 | LED Industrial outdoor type Bulkhead luminaires,IP rating not less than 45, highly resistant to dust and water 1 x 9/10 Watt fitting in engineering plastic housing with clear prismatic diffuser complete with all accessories and connecting up with flexible cable white of suitable size and making necessary connection fixed as in repair complete all as specified and directed. |
| 136 | LED 18 W recess mounted indoor type back lit downlighter suited for any modern workspace of size not less than 6\\" round/square, fixed as in repair complete all as specified and directed. |
| 137 | Decorative, wall mounting, brushed nickel finish fixture with Single opal glass diffuser including 1 x 9W LED lamp B22 base, perfect ambience for living/bedroom fixed as in repair complete all as specified and directed. |
| 138 | Decorative, wall mounting, brushed nickel finish fixture with double opal glass diffuser including 2 x 9W LED lamp B22 base, perfect ambience for living/bedroom fixed as in repair complete all as specified and directed. |
| 139 | Modern bedside wall mounted reading fitting LED 2 Watt, adjustable head for better beam and focus, touch control switch, uniform light LED integration for right ambience, as per sample approved, complete all as specified and directed. |
| 140 | S&F in replacement of Recess / Surface mounted LED, 1' X 1', 15 watt, cool day/warm white light, edge lit tile in extruded aluminium / CRCA steel sheet powder coated housing with full opal diffuser suitable for perfect lighting complete including cutting hole of required size in POP/ false ceiling and making good of disturbed surface complete all as specified and as directed by Engineer-in-Charge. |
| 141 | S&F in replacement Recess / Surface mounted LED, 2' X 2', 36 watt, cool day/warm white light (6000 K), edge lit tile in extruded aluminium / CRCA steel sheet powder coated housing with full opal diffuser suitable for perfect lighting complete including cutting hole of required size in POP/ false ceiling and making good of disturbed surface complete all as specified and as directed by Engineer-in-Charge. |
| 142 | S&F in replacement decorative outdoor wall light LED 12 Watt warm white, mygarden black & stainless steel body, Flush Mount type, IP44, protection complete all as specified and directed. |
| 143 | S&F LED building security light fitting 1 x 35 Watt new generation energy saving and environmental friendly long life LED street light made up of pressure diecast aluminium housing with high power LED as lighting source and lens embedded PC cover having top opening seperate driver compartment with IP65 protection incl mounting bracket of suitable size and connection complete all as specified and directed. |
| 144 | Taking down carefully old unserviceable ceiling fans/wall fan /exhaust fans complete, removing its blade and deposit to the MES Store yard for serviceabilty check and further board of action, complete all as specified and directed. |
| 145 | Hanging/fixing only serviceable ceiling/exhaust fan any make/ sweep and connecting up with existing electric circuit complete received from MES Store Yard, all as specified and directed. |
| 146 | Fresh air circulating ventilators fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300mm and connecting up including louvers including making necessary opening on stone /brick masonry wall of suitable size, finishing it properly and making good with matching colour with the surroundings provision of cable 3 core of of suitable size from ceiling rose to fan complete all as specified and as directed. |
| 147 | Royal Premium Ceiling Fan 1200MM Antique Copper Oak Aesthetic 1200 mm Ceiling Fan with 5-Blade, Smart Remote controle, Premium Wooden Finish, Superior Airflow with (BLDC) brushless direct current motor and connection complete all as specified and directed. |
| 148 | Exhaust fans for kitchen with louvers 300 mm sweep, 1400 RPM, Heavy duty single phase 240 Volts, AC 50 Hz, steel body and connecting up including louvers including making necessary opening on stone /brick masonry wall of suitable size, finishing it properly and making good with matching colour with the surroundings provision of cable 3 core of suitable size from ceiling rose to fan complete all as specified and as directed. |
| 149 | Wall Mounted fans for kitchen dacorative type 400 mm sweep, 230V AC Supply, 50 Hz, high performance, smooth oscillation, copper bound motor made of sturdy Engineering plastic and metal ribs guard complete as per complete all as specified and as directed. |
| 150 | S&F single pole and neutral sheet metal enclosure with a two pin and earth plug and socket complete with one number single pole MCB 20 Amps , 240 Volts for AC/Geyser point complete all as specified and as directed. |
| 151 | Taking down carefully Geysers of any capacity and removing with materials to store for keeping in safe custody by the contactor and deposit to the MES Store yard check its serviceability and further BER board action as per direction. |
| 152 | Fixing only serviceable Geysers of any capacity and connecting up with existing site as per direction complete received from MES Store Yard all as specified and directed. |
| 153 | Supply , installation, testing and commissioning of electric water heater (Geyser), storage vertical or horizontal type as approved , BEE 5 star rated, 25 litre capacity, 230 volts AC, 50 Hz comprising of high voltage heating element upto 2 KW for instatnt heating, ABS tech/ Engineering thermoplastic body or steel/ metal body with steel inner tank with corrosion resistance coating , rust and shock proof with and including provision of Pressure relief valve and grouting bolts suitably flushed to wall or any other surfcae including PVC connection & electric connection with 3 core PVC insulated, sheathed, stranded copper conductor cable / flexiable chord with plug complete all as specified and directed. |
| 154 | Auto clean glass Chimney with invertor technology, Suction Capacity 1400-1500 m3/h, Filterless tech 6062 BLDC, size approx 90cm AC, multiple speeds control Brushless powerful DC motor, Touch controls with motion sensor, wave and start, Stainless Steel body black colour with LED Light including Flexible adjustable to length PVC Pipe 150 mm for fixing in wall inside with proper wall hole and PCC work and outside for exhaust cooking air through chimney with lovers complete all as specified and directed. |
| 155 | Disconnecting and taking down old us sub main wiring complete with concealed conduit/batten of any type and size removing mtrls and making good distrubed surfaces of walls, floors, etc complete all as specified and directed |
| 156 | M&L of Sub main wiring with two runs of single core PVC insulated and unsheathed multistranded, copper conductor (FRLSH) cable of size 4.0 sqmm, LT, 1100V grade, drawn through and including adequate size PVC non metallic conduit with accessories and fittings and one run of 4.0 sq mm single core multi stranded copper conductor cable as earth continuity conductor complete all as specified and directed by Engineer-in-charge. |
| 157 | M&L of Sub main wiring with two runs of single core PVC insulated and unsheathed multistranded, copper conductor (FRLSH) cable of size 6.0 sqmm, LT, 1100V grade, drawn through and including adequate size PVC non metallic conduit with accessories and fittings and one run of 6.0 sq mm single core multi stranded copper conductor cable as earth continuity conductor complete all as specified and directed by Engineer-in-charge. |
| 158 | M&L of Sub main wiring with four runs of single core PVC insulated and unsheathed multistranded, copper conductor (FRLSH) cable of size 10.0 sqmm, LT, 1100V grade, down through and incl adequate sizes PVC non metallic conduit of suitable dia with accessories and fittings and one run of 10.0 sq mm single core multi stranded copper conductor cable as earth continuity conductor complete all as specified and as directed by engineer-in-charge. |
| 159 | M&L cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified. |
| 160 | Disconnecting and taking down old unserviceable DBs/junction box/panels ect of any type and size complete along with all MCCBs/MCBs etc all as specified and directed. |
| 161 | Supply & fixing Vertical TPN distribution board double door flush mounting with provisions for MCCBs incomer upto 125 Amp & outgoing 4 way having IP 54 protection complete. |
| 162 | Supply and fixing Distribution board double door flush mounting MCB TPN 4 Way with provisions for MCBs incomer & outgoing having IP 54 protection complete. |
| 163 | Supply & fix Distribution Board factory made sheet metal enclosure double door distribution board class IP-43 IK 09 with 200 Amp rated copper bus bar 240 Volts 12 way (2 + 10 way) single pole and neutral link, complete all as specified and as directed. |
| 164 | S&F for MCCB 4 pole, 3 phase 415 volts of capacity 125 Amp, 25 KA with adjustable thermal and magnetic release complete with proper copper thimble/lux all as specified and directed. |
| 165 | S&F MCB Tripple pole and neutral (TP&N) 63 Amp 415 volts 10 KA 'C' series with all incoming/outgoing connections with proper size lugs, complete all as specified and directed. |
| 166 | S&F MCB single pole and neutral (SP&N) 40 to 63 Amp 240 volts 10 KA 'C' series with all incoming/outgoing connections with proper size lugs, complete all as specified and directed. |
| 167 | S&F MCB single pole (SP) 40 to 63 Amp 240 Volts 10 KA 'C' series with all incoming/outgoing connection with proper size lugs, complete all as specified and directed. |
| 168 | S&F MCB single pole (SP) 6 to 32 Amp 240 Volts 10 KA 'C' series with all incoming/outgoing connection with proper size lugs, complete all as specified and directed. |
| 169 | Earthing complete with galvanized steel earth plate electrode 60cmx60cmx6.00mm thick, burried directly in ground vertically to a depth not less than 2.25m below normal ground level, with top edge of the plate not less than 1.5m below normal ground level, earth plate surrounded by 15cm thick and packed alternate layers of charcoal dust and common salt, connected with and including earth lead of GI wire 4mm dia (8 SWG) by means of bolts, nuts, check nuts and washers of galvanized iron or thimbles and other end of the earth wire connected to main switch board and protected by galvanized iron pipe light grade 15mm dia bore including watering pipe 20mm dia bore GI light grade (ISI marked) with funnel and wire mesh, including all necessary excavation and earth work, PCC chamber in plain cement concrete (1:3:6) type C-1 and pit cover of presast RCC with MS frame etc and all as shown in electrical plate No 3 of MES Sch Part-I (2009), complete including dismantling of old earthing, all as specified and directed. Note(s) :-(i) RCC pit cover shall be pre-cast of RCC (1:2:4) type B-1, 80mm thick reinforced with XPM not less than 4Kg/Sqm.(ii) PCC chamber shall be constructed 500 mm away from the edge of earth pit.(iii) Rate shall include earth lead and protection pipe of length 7.5m(iv) Earth resistance should be less than 3Ohm. In case the test results are not found below 3Ohm, complete earthing will be redone without any extra cost to Govt.(v) unit rate including protection pipe and GI wire 4.00mm dia from top to earth plate upto 7.5 meter Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 24, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 15, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 14 daysAug 17, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 16 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender