Tender For Repair/Replacement Of Furniture Against Condemnation Under Ge Kaluchak

Sharing tender

Tender For Repair/Replacement Of Furniture Against Condemnation Under Ge Kaluchak- 1 Wooden Furniture : 2 Sofa Set 4 Seateroverall Size Of One Seat Shall Be 670Mm Long And 745 Mm Wide And 530Mm High Up To Arm Rest Level. The Sofa Set 4 Seater Shall Consist Of Four Single Seats. All Wood Shall Be Of First Class Teak Wood (Mp). Legs Of Sofa Set Shall Be 70Mm X35Mm In Section Teak Wood . Front Legs Shall Be Joined By 100Mm X 35Mm In Section Wooden Rail In Front. Front And Rear Legs Shall Be Joined With 100Mm X 35Mm In Section Wooden Rails In Sides. Arm Rests Shall Be Made To Shape Of Size 70Mm X 35Mm In Section Teak Wood. Back Rest Shall Be Made As Frame Of 70Mm X 35Mm In Section Wooden Horizontal At Bottom And Top And Vertical Sides Slanting As 560Mm. 100Mm Thick Seat Cushion And Back Cushions Shall Be Of Size 530Mm X 560Mm (One Numbers In Seat And One Numbers In The Back). The Cushion Shall Be Superior Quality Foam Of 40 Density As Approved By Engineer-In-Charge. Cushion Shall Be Covered With Tapestry Cloth Approved By Engr-In-Charge/Ge. All Wooden Surface Exposed To View When Placed In Position Shall Be French Polished With Lacquer Finish Rest. Rest All As Per Drg. 3 Sofa Set 5 Seateroverall Size Of Three Seat Piece Shall Be 1730Mm Long, 745Mm Wide And 530Mm High Up To Arm Rest Level. Overall Size Of One Piece Shall Be 670Mm Long And 745 Mm Wide And 530Mm High Up To Arm Rest Level. The Sofa Set To Seat Five Shall Consist Of One Large Three Seat Piece And Two Small One Seat Pieces.. All Wood Shall Be Of First Class Teak Wood (Mp) Legs Of Sofa Set Shall Be 70Mm X35Mm In Section Teak Wood . Front Legs Shall Be Jointed By 100Mm X 35Mm In Section Wooden Rail In Front . Front And Rear Legs Shall Be Joined With 100Mm X 35Mm In Section Wooden Rails In Sides. The Top Of Front Rail And Side Rails Shall Be 300Mm From Bottom Of Legs. Three Wooden Bearers Of 40Mm X 40Mm In Section Shall Be Provided Below The Seat To Support Wood Battens Of 50Mm X 20Mm In Section. 21 Numbers Wooden Battens Shall Be Provided For The Seat Of Large Three Seat Set And 7 Numbers Wooden Battens Shall Be Provided To The Set Of One Seat Set. Arm Rests Shall Be Made To Shape Of Size 70Mm X 35Mm In Section Teak Wood. Back Rest Shall Be Made As Frame Of 70Mm X 35Mm In Section Wooden Horizontal At Bottom And Top And Vertical Sides Slanting As 560Mm, 14 Numbers Battens Of Teak Wood Shall Be Provided For The Long Seat And Four Numbers Of Battens Shall Be Provided For One Seat In The Wooden Frame Of Back Rest. 30Mm X 50Mm In Section Wooden Rail To Support Back Frame Shall Be Provided Joining The Rear Legs, 100Mm Thick Seat Cushion And Back Cushions Shall Be Of Size 530Mm X 560Mm (Three Numbers In Seat And Three Numbers In The Back For The Large Seat). The Cushion Shall Be Superior Quality Foam Of 40 Density As Approved By Engineer-In-Charge. Cushion Shall Be Covered With Tapestry Cloth Approved By Engr-In-Charge/Ge. All Wood Surface Exposed To View When Placed In Position Shall Be French Polished With Lacquer Finish Rest. Rest All As Per Drg. 4 Sideboardoverall Size Shall Be 1025Mm Long, 450Mm Wide And 750Mm High. Back Shall Be 1025Mm Long And 750Mm High Pre-Laminated Particle Bd 19Mm Thick/18Mm Mdf, Sides Shall Be 450Mm Wide And 675Mm High Pre-Laminated Mdf Board 18/19Mm Thick. Base Shall Be Of 75Mm High 18/19Mm Thick Pre-Laminated Mdf Fixed At 25Mm From Front And Sides. Top And Bottom Shall Be Of 19Mm Thick Pre-Laminated Mdf Board. A Verticle Partition Of 19Mm Thick Pre-Laminated Particle Bd /18Mm Thick Mdf Shall Be Provided At 358Mm From Inside Of Right Hand Side Pre-Laminated Particle Board/18Mm Thick Mdf. Four Drawers Shall Be Provided Equally In This Space. Three Pieces Of Particle Board 40Mmx19Mm And 358Mm Long Shall Be Provided Over The Lower Three Drawers. Bottom, Sides Back Of Drawers Shall Be Of 19Mm Thick Particle Bd. The Front Of Drawers Shall Be Of 19Mm Thick Pre-Laminated Particle Bd/18Mm Thick Mdf 20Mm X20Mm Teak Wood Bearers Fixed Exactly In Centre Of Both Sides Of The Drawers Shall Be Provided To Each Drawer. Another 20Mm X20Mm Teak Wood Bearer Shall Be Fixed To The Vertical Of The Side Bd In Such A Way The The Bearers Fixed With The Sides Of The Drawer Shall Slide Over Smoothly. On Left Side Compartment Two Horizontal Shelves, Equally Spaced Shall Provided As Shown On Drawing. The Size Of Shelves Shall Be 610Mm Long, And 387 Mm Wide. Two Side Hung Shutters Shall Be Provided To Left Hand Side Of Side Board. The Shutters Shall Be Side Hung With 20Mm Size Piano Type Hinges. The Shutters Shall Be Of 19Mm Thick Pre-Laminated Particle Board/18Mm Thick Mdf. 4Mm Thick Teak Wood Edging Shall Be Provided Alround The Front Shutters And Front Of Shelves. Shelves Shall Be Fixed Over The Standard Aluminium Shelf Support. On All Visible Front Edges Of Pre-Laminated Particle Bd/Mdf Bd Shall Be Provided With 4Mm Thick Teak Wood Edging. All Drawers And Shutters Shall Be Provided With One Handle Each Of Powder Coated Mild Steel And 100Mm Long. Two Catch Spring Shall Be Provided To Shutters As Directed By Engineer-In-Charge. All Wood Surfaces Exposed To View When Placed In Position Shall Be Given High Gloss French Polish With Lacquer Fininsh. 5 Stool Dressing Cushionedoverall Size Shall Be 450 Mm Long,300Mm Wide And 380Mm High. All Wood Shall Be Ist Class Teak Wood.The Size Of The Legs Shall Be Of Size 50Mmx30Mm .The Size Of The Three Bottom Stiffener Shall Be Of Size 19Mmx25Mm.The Size Of The Top Rails Shall Be Of Size 25Mmx65Mm.12Mm Thick Commercial Plywood Shall Be Fixed Over The Top Rails For Seat .The Seat Of The Stool Shall Be Made Of 75Mm Thick Foam Cushion Of 40 Density Duly Covered With Best Quality Tapestry Clothas Approved By Engr-In-Charge/Ge. Rest All As Per Drg. All Wood Surface Exposed To View When Placed In Position Shall Be French Polished With Lacquer Finish Rest.Rest All As Per Drg. 6 Table Dining 4 Personsoverall Size Shall Be 1200Mm Long, 900Mm Wide And 750Mm High. All Wood Shall Be Of First Class Teak Wood (Mp).The Top Shall Be Of Prelaminated Mdf Board Of 18/19Mm Thick With 4Mm Thick Teak Wood Beading Alround The Edges Of The Top Fixed With Headless Nails And Adhesive On Long Sides Only . Four Legs Shall Be 90Mm×45Mm In Section And 750Mm High. Legs Shall Be Joined By 45Mm×90Mm Teak Wood Rails In Long And Short Sides At Top In Such A Way That Top Of Legs And Top Of Rails Shall Be At One Level. 25Mmx45Mm Teak Wood Wooden Member Of Size 900Mm Long Shall Also Be Provided As Shown In Drg. Two Stiffeners Of 90Mm×25Mm In Section Shall Be Fixed Equally Spaced Joining The Long Rails With Dove Tailed Joints.Four Wooden Brackets /Corners Of Size 100Mmx100Mmx35Mm Thick Shall Also Be Provided Over Ms 150Mmx30Mmx5Mm Right Angle Iron Bracket Screwed With Rail And Leg. 25Mm×25Mm Pvc Shoes Shall Be Provided At The Bottom Of The Table. Rest All As Per Drgs. All Wood Surfaces Exposed To View When Placed In Position Shall Given High Gloss French Polish With Lacquer Finish 7 Table Dressing Ladies With Mirrorthe Overall Size Of The Table Dressing Shall Be 1150Mm Long 380Mm Wide And 1700Mm High. The Sides, Top ,Back And Front Of The Base Unit Shall Be Of 18Mm Thick Prelaminated Mdf Board. The Bottom Of The Side Units Shall Be Of 12Mm Thick Commercial Plywood. The Sides And Back Drawers Shall Be Of 12Mm Thick Prelaminated Mdf ,Bottom Of The Drawers Shall Be Of 6Mm Thick Commercial Ply Whereas The Front Of The Drawers Shall Be Of 18Mm Thick Prelaminated Mdf Board.5Mm Thick Electro Copper Plated Mirror Shall Be Fixed Over 6Mm Thick Plywood Back. The Plywood Shall Be Fixed On Two Vertical Hardwood Member Of Size 45Mmx35Mm .A Horizontal Support Of Size 30Mmx20Mm Shall Be Provided In Between Two Vertical Members. The Overall Size Of The Stool Shall Be 440Mm Long 350Mm Wide And 425Mm High. The Four Sides Shall Be Of 18Mm Thick Prelaminated Mdf .The Top Of The Stool Shall Be Of 12Mm Thick Plywood Openable As Shown In Drg.Four Heavy Duty Revolving Nylon Double Wheels Shall Be Provided At Base Below The 6Mm Base Ply Fixed Over Wooden Runner 20Mmx20Mm.The Seat Of The Stool Shall Be 75Mm High ,Made Of Foam 40 Density Covered With Tapestry Cloth As Approved By Engr-In-Charge/Ge.Rest All As Per Drg. Overall Size Shall Be 900Mm Long, 380Mm Wide And 1700Mm High (Height Is Of The Mirror). All Wood Surfaces Exposed To View When Placed In Position Shall Given High Gloss French Polish With Lacquer Finish.Rest All As Per Drg. 8 Table Centre With Glasstopoverall Size Shall Be 1200Mm Long, 600Mm Wide And 400Mm High. Legs Shall Be Of 40Mm Dia Anodized Brass Legs, Four In Number In One Piece. The Legs Shall Be Joined In Short And Long Sides With Two Number 25Mm Dia Brass Pipes Of Wall Thickness 2Mm. The Top Pipe Shall Be Fixed 150Mm From Top And The Lower Pipe Shall Be At 100 From Bottom Of Top Pipe The Brass Frame Shall Be 900Mm Long And 450Mm Wide. Vaacuum Rubber Sho Shall Be Provided At Top Of Legs, Which Shall Be Closed With Brass Sheet 1.6Mm Thick. The Bottom Of Legs Shall Be Covered With Brass Sheet Of 1.6Mm Thick Sheet. The Bottom Of Legs Shall Have Pvc Shoes. The Top Shall Be 10Mm Thick Plate Tinted Glass (White Colour) With Corners Rounded As Shown Drawing, The Edges Of Top Of Table Shall Be Rounded Off. 9 Peg Tableoverall Size Shall Be 450Mm Long,300Mm Wide And 380Mm High.Legs Shall Be Of Teak Wood Of Section 30Mmx50Mm.The Legs Shall Be 362Mm High.5Mmx5Mm In Section Groove Shall Be Provided On The Top Of Legs Which Shall Be Visible When Placed In Position.Two Nos Top Rails Of Section 20Mmx40Mm Of Teak Wood Shall Be Provided Connecting Legs.Two Bottom Rails Of Size 20Mmx40Mm Shall Be Fixed Between The Legs .A Centre Stiffeners Of Size 20X40Mm Shall Be Provided At Centre Of Side Bottom Rails For Extra Support Irrespective Of What Is Shown On Drg.Top Of The Table Shall Be Of 18Mm Thick Pre-Laminated Mdf Board With 4Mm Teak Wood Edging All Round The Top Of Table.All Wood Surfaces Exposed To View When Placed In Position Shall Be French Polished With High Lacquer Finish.Rest All As Per Drg. 10 Table Writingoverall Size Shall Be 1145Mm Long, 600Mm Wide And 760Mm High. All Wood Shall Be Of First Class Hard Teak Wood Except Top And Right Hand Side Drawer Cabinet. Legs Shall Be Of 35Mmx55Mm In Section And 717Mm High Having 5Mmx5Mm In Section Groove At The Top Of Legs At The Portion When Placed In Position. The Top Shall Be Of 18Mm Thick Prelaminated Mdf Board Of Approved Shade And The Edges Shall Be Covered With 4Mm Thick Teak Wood Beading. Two Short Stiffeners Of Teak Wood Of Size 50Mmx40Mm In Section Irrespective Of What Is Shown On Drg Shall Be Provided Between Legs At 100Mm From Bottom Of Legs. Sides Of The Box Which House The Drawer And Cabinet Shall Be 18Mm Thick Prelaminated Mdf Board Exterior Grade. Sides And Back Of Drawers Shall Be Of 12Mm Thick Teak Wood Planks. Bottom Of Drawers Shall Be Of 6 Mm Thick Plywood Commercial.6Mm Thick Plywood Commercial 75Mm High Partition Shall Be Provided In The Drawer. Shutter For Cabinet Shall Be Fixed With Piano Type Continuous Hinges. Lock Shall Be Provided To Drawer And Shutters. Recessed Handle Shall Be Provided To Drawer And Shutter.25Mm Dia And 25Mm High Rubber Shoes Shall Be Fixed To Bottom Of Legs. All Wood Surfaces Shall Be French Polished With High Gloss Finish. Rest All As Per Drg. 11 Teapoythe Overall Size Shall Be 600Mm Long, 450Mm Wide And 540Mm High. The Legs Shall Be 60Mmx30Mm In Section And 497 Mm High And Shall Be Of Teak Wood.5Mmx5Mm In Section Groove Shall Be Provided At The Visible Portion Of Top Of Legs. Top Rails Of Teak Wood Of 20Mmx50Mm In Section And 510Mm Long Shall Be Provided Between The Legs. Bottom Rail Of Teak Wood Of 20Mmx50Mm In Section And 420Mm Long Shall Be Provided Between Legs, Widthwise At 100Mm Above The Bottom Of Legs. A Centre Rail Of Size 20Mmx50Mm Shall Also Be Provided Lengthwise At Centre In Between The Side Bottom Rails Irrespective Of What Is Shown On Drg.25Mm Thick And 25Mm Dia Hard Rubber /Pvc Rings Shall Be Fixed To The Bottom Of All Legs Fixed With 30Mm Long Screws.Top Of Table Shall Be Of 18 Mm Thick Pre-Laminated Mdf Board With 4Mm Teak Wood Edging Al-Round The Top Of Table. All Wood Surfaces Shall Be French Polished With High Gloss Finish. Rest All As Per Drg 12 Steel Furniture : 13 Almirah Large Steeloverall Size Shall Be 1985Mm High,920Mm Wide And 485Mm Deep. The Base Shall Be Made Of Two Numbers Mild Steel Sheet Channel Bases Made In U Shaped With Ends Covered. Mild Steel Sheet Shall Be 1Mm Thick. The Base Channel Shall Be Welded At 50Mm From Each End Of The Length Of 920Mm And Shall Be Up To Full Width Of 485Mm And Shall Be 100Mm High Top, Side’S Bottom And Back Of Almirah Shall Be Of 1Mm Thick Mild Steel Sheet. Four Shelves Equally Spaced Of 1Mm Thick Mild Steel Sheet Shall Be Provided To Make Five Compartments. Front Shutter Shall Two Leaves Of Equal Size. Front Shutter Leaves Shall Have Three Butt Hinges Of 75Mm Fixed To Each Shutter And Shall Be Side Hung. All Joints And Welding And Fixing Shall Be Done In Accordance With The Standard Workmanship. One Chromium Plated Steel Handle With A Locking Device Shall Be Provided As Shown On Drawing. The Locking Device Shall Be Three Way Locking Device And Shall Also Be Provided With Decorative Key Plate. All Steel Surfaces Exposed To View When Placed In Position Shall Be Painted With Two Coats Of Silver Grey Hammer Paint Internally And Extrenally With Spray Machine After Preparation Of Surfaces. A Mark Of Mes Shall Also Be Provided On Left Top Corner Of Front Shutter Of Visible Colour As Directed By Engr-In-Charge. Rest All As Per Drg 14 Almirah Medium Steeloverall Size Shall Be 1270Mm High,765Mm Wide And 440Mm Deep.The Base Shall Be Made Of Two Numbers Mild Steel Sheet Channel Base Welded To Bottom Of Almirah And Shall Be 100Mm High. Mild Steel Sheet Shall Be 1Mm Thick For Channel Base. The Base Channel Shall Be Welded At 50Mm From Each End Of 765Mm Length And Shall Be Up To Full Width Of 440Mm Of Almirah. Top, Sides, Back, Bottom And Front Of Almirah Shall Be Of 1Mm Thick Mild Steel Sheet. Three Shelves Equally Spaced Making Four Compartments Shall Be Provided And Shall Be Of 1Mm Thick Mild Steel Sheet.Front Shutters Shall Have Two Leaves.All Joints And Welding, Fixing Shall Be Done According Standard Workmanship. A Steel Chromium Plated Handle 100Mm Long Shall Be Provided To The Shutter.The Locking Device Shall Be Three Way Locking Device And Shall Also Be Provided With Decorative Key Plate. All Steel Surfaces Exposed To View When Placed In Position Shall Be Painted With Two Coats Of Silver/Grey Hammertone Paint Over A Coat Of Primer With Spray Machine After Preparation Of Surfaces. A Mark Of Mes Shall Also Be Provided On Left Top Corner Of Front Shutter Of Visible Colour As Directed By Engr-In-Charge. Rest All As Per Drg. 15 Chair Writing (Offrs)The Overall Size Of The Chair Shall Approx Be 950Mm High And 500Mm Wide. The Frame Of The Chair Shall Be Of Ms Tubular Frame Powder Coated, Cantilever Type Of Size 25Mmx10Mm In Section. Back Form Shall Be Designed With Contoured Lumber Support For Extra Comfort.120Mm Thick Hot Pressed Plywood Upholstered With Superior Quality Fabric And Moulded Polyurethane Foam With Pvc Lipping Alround Shall Be Provided At Seat And Back. Pu Arms Shall Be Of Superior Quality And Reinforced With Ms Insert.It Shall Be Scratch And Weather Resistant. Steel Portion Of Chair Shall Be Powder Coated. Rest All Specifications Are As Per Drg And Directed By Ge. 16 Book Case Steelover All Size Shall Be Of 840 Mm Long, 310 Mm Wide And 1675 Mm High .All Sheet Shall Be Mild Steel Sheet 1 Mm Thick, Back, Sides, Bottom, Top And Shelves.The Book Case Shall Be Provided With Four Compartments Of Equal Size. The Shutters Each Compartment Shall Open Towards Top And Slide Into The Depth Of The Book Case. Two Steel Handles Of 100 Mm Long Shall Be Provided To Each Shutter Of The Compartment. The Locking Device Shall Be Provided To Each Compartment With Duplicate Key. All Steel And Iron Surfaces Exposed To View When Placed In Position Shall Be Given Two Coats Of Granular Silver Grey Enamel Paint Over A Coat Of Primer After Preparation Of Surfaces. Rest All As Shown On Drg. 17 Chair Computerthe Base Pedestal Assembly Of Chair Computer Shall Be Of Dia 700Mm And 1060Mm High .The Pedestal Assembly Shall Be Provided With Injection Molded In Black 30% Glass Filled Nylon. A 10.5Mm Dia Forged Bright Zinc Plated Ms Castor Pin Is Of Press Fitted Into Each Prong For Holding The Castors. The Seat And Back Of The Chair Computer Shall Be Made Of 12Mm Thick Hot Pressed Plywood Upholstered With Fabric And Moulded Polyurethane Foam. The Back Form Shall Be Designed With Contour Lumber Support For Extra Comfort With Pvc Lipping Allround.The Back Rest Shall Be Adjustable And Consist Of Drop Lift Mechanism And Shall Be Adjusted In The Insert .It Shall Be Scratch And Weather Resistant. Rest All As Per Drg And As Approved By Engr-In-Charge/Ge 18 Charpoy Ip Hardtopoverall Size Shall Be 1980Mm Long, 900Mm Wide And 440Mm High. Two Long Rails And Two Short Rails Shall Be Of 25Mmx65Mmx16 Gauge Ms Rectangular Pipe. The Legs Shall Be Of Size 32Mmx32Mmx16 Gauge Welded To Long And Short Rails As Shown On Drg.Two Stiffeners Of Size 25Mmx25Mmx16 Gauge Shall Be Provided In Equidistant Between Two Opposite Long Rails. Six Number Cleat Of Size 25Mmx60Mmx6Mm Shall Be Welded With Frame To Support Ply. Two Stiffeners Joining Legs Of Size 25Mmx25Mmx16 Gauge Shall Be Provided At 150Mm From Ground Level .12Mm Thick Commercial Plywood Shall Be Provided For Top As Shown On Drg With Proper Nut And Bolt .One Nut And Bolt Shall Also Be Provided At Centre Of Each Stiffeners For Fixing The Plywood Irrespective Of What Is Shown On Drg.Pvc Hard Rubber Shoes Shall Be Fixed At Bottom Of Each Leg. All Steel Surfaces Shall Be Painted With Synthetic Enamel Black In Color Over A Coat Of Primer. Rest All As Per Drg 19 Table Bedsidethe Overall Size Of The Table Bed Side Shall Be 450Mm X 450Mm X 500Mm As Shown In Drg.The Entire Frame Of Table Bed Side Shall Be Made Up Of 18Mm Ms Square Pipe (18 Gauge) Duly Black Powder Coated. The Two Sides And Top Shall Be Made Up Of 18Mm Thick Prelamainted Mdf Board. The Back Of The Table Except The Top Portion As Shown In Drg Shall Be Provided With 6Mm Commercial Plywood Bwr Grade Duly Screwed To Frame. The Two Sides, Back And Bottom Of Drawers Of The Table Shall Be Made Up Of 12Mm Thick Commercial Plywood Irrespective Of What Is Shown On Drg, Except The Front Side Which Shall Be Of 18Mm Thick Prelaminated Mdf Board Of Walnut Shade. The Drawers Shall Be Made Functional On Teak Wood Runners Fixed Inside The Tables Shown On Drg.The Drawers Of The Tables Shall Be Provided With 100Mm Long Cp Handles.The Edges Of The Drawers Or Mdf Board Shall Be Covered With 4Mm Thick Teak Wood Bearer. Rest All As Per Drg. All Wooden Surfaces Shall Be French Polished With Two Coats After Preparation Of Surfaces And Steel Portion Shall Be Painted With Synthetic Enamel Black Paint. 20 Bathmat Pvcthe Size Of The Bath Mat Shall Be 400Mm L X 300Mm W X 250Mm H.Bath Mat Pvc Shall Be Made Up Of 5Mm Thick Ppcp Material .The Bath Mat Shall Have Centre Leg Of Dia 25Mm.The Four Legs Shall Be In Arc Shape And Of Size 10Mmx100Mm.The Top Of The Bath Mat Shall Have 3Mmx10Mm Thick Stiffener Moulded Along With The Seat In Single Piece Underneath. The Weight Of The Bath Mat Shall Not Be Less Than 1.3 Kgs. Make-Amko Or Equivalent