Tender For Establishing New Tribal Interpretation / Cultural Experience Centre At Old Paliyar Kudiyiruppu In Thalayanai Eco Tourism Site In Vasudevanallur Rf, Thalayani North Beat, Thalayanai Section, Puliyankudi Range Of Tenkasi Divison
Tender Value
14 Lakhs
Estimated cost
Bid Submission
01 Aug 2026
4 days left
EMD
14000
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Tenkasi → Tamil Nadu
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Establishing New Tribal Interpretation / Cultural Experience Centre At Old Paliyar Kudiyiruppu In Thalayanai Eco Tourism Site In Vasudevanallur Rf, Thalayani North Beat, Thalayanai Section, Puliyankudi Range Of Tenkasi Divison
BOQ
| Sl. No. | Item Description |
| 1 | Earth work excavation for foundation (for narrow excavation) in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification. |
| 2 | Cement Concrete 1:5:10 (One Cement, Five M.Sand and Ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification |
| 3 | Supplying and filling in foundation, basement, etc with filling M.Sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers. |
| 4 | Supplying and filling in foundation, basement, etc with conveyed Well gravel in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers. |
| 5 | Flooring Concrete 1:5:10 (One cement, Four M.Sand and Eight hard broken stone) using 40 mm gauge hard broken jelly for flooring including laying, consolidating, finishing, rendering the top surface rough to receive the floor, curing, etc. complete complying with standard specification. (The rate is inclusive of necessary planking for panelling wherever necessary and as directed by the departmental officers. |
| 6 | Plain Cement Concrete 1:2:4 (one cement, two crushed stone sand and four hard broken stone jelly) using 6mm-12mm jelly for wearing coat including laying, compacting, finishing and curing, etc., complete as per standard specificatins and as directed by the departmental officers.- Mixing by manual means |
| 7 | Brick work in Cement Mortar 1:5 (One Cement, Five crushed stone sand) using best quality Second Class Ground Moulded Chamber Burnt Bricks of size 9\\" x 4 3/8\\" x 2 3/4\\" including Cost of Mortar Plasticizer curing, etc.,complete complying with standard specification . |
| 8 | For foundation & basement |
| 9 | For Super Structure in G.F |
| 10 | Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (Payment for centering shall be given after the concrete is laid) |
| 11 | Cement Concrete 1:1-1/2:3 (One Cement, One and a half M.Sand and Three hard broken stone jelly) using 20 mm gauge hard broken granite stone jelly for all RCC items of works excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor / roof slabs wherever necessary and bearing surfaces of walls, beams etc |
| 12 | For foundation & basement |
| 13 | Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel grills for all RCC works as per design given including cost of steel and G.I. binding wire in all floors etc. complete complying with standard specification. (Contractor has to make his own arrangements for the supply of steel and binding wire) Foundation & basement |
| 14 | Supply and fabrication of Mild steel square section truss and purlins for Roofing with colour galvalume sheet of 0.47mm thick (as per lowest quatation) |
| 15 | Supplying , fixing and roofing with Stone Coated Metal Roofing Sheet prefabricated roofing sheet with all necessary accessories such as J/V bolt and nuts of suitable length with suitable bitumen washers complete complying with standard specification and as directed by the department |
| 16 | Paving the floor with best quality Attangudi Tiles Size 12 x 12 x 3/4 and variety conforming IS 15622 with water absorbtion less than 0.08% of approved colour and shade laid over cement mortar bed of 20mm thick in cement mortar 1:3 (one cement and three crushed stone sand) with required Cement Slurry and Mortar Plasticizer in all floors and the top pointed with Water Resistant Tile Epoxy Grout etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Forest Officer before use on works) |
| 17 | Fabricating, Supplying and fixng in position of MS square bar of 12mm size is welded to the inner face of the stay made out of 18 x 5mm at 0.70 kg/ m MS flat at an equal interval not exceeding 100mm edge between them. All members are painted with one coat of anti-corrosive red oxide primer as directed by the departmental officers.All sections should be in confirmed with IS 7452/1990 |
| 18 | Plastering with Cement Mortar 1:5 (One cement and Five sand), 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers. |
| 19 | Supplying and painting the walls with two coats of wall putty as instructed by thedepartmental officers including preparation of surface curing, etc., complete in all floors complying with standard specifications and as directed by the departmental officers. (The wall putty shall be got approved by the Executive Engineer before use of work). |
| 20 | Painting Two coats with ready mixed Interior Plastic Emulsion Paint approved quality and colour including a priming coat, including thorough scrapping, clean removal of dirt, etc complete and including necessary plaster of paris, putty, wherever required etc, complete as per standard specification. - 10 sq.m |
| 21 | Painting two coats with ready mixed Exterior Emulsion Paint approved quality and colour including a priming coat, including thorough scrapping, clean removal of dirt, etc complete and including necessary plaster of paris, putty, wherever required etc, complete as per standard specification. - 10 sq.m |
| 22 | Supplying and fixing inposition C.R.C.A.pressed steel doors frame as per I.S.4351/1976 of size 105x60mm with 35x12mm rebate on all sides with 1.25mm thick (18 gauge) sheet frames special profile extruded section including bottom tie hold faste at appropriate places and provision to fix aldrops tower bolts hinges and lock strike plate etc.The door frame inner shall be packed with CC 1:2:4 using 12mm guage HBG stone jelly including fixing the door frames inposition and dimantling the masonry and concrete wherever necessary and redoing the same original condition after fixing including scaffolding charges and labour charges and door frame will be given one coat of Red Oxide primer etc. Complete complying with standard specification The rate shall inclusive of all materials, labour, transportation, loading, unloading, handling, charges etc SOR M-0303 |
| 23 | Providing of 35mm thick factory made pre-laminated ABS (Acrolynitrile Butadiene Styrene) Door Shutter moulded in different designs, consisting of all round frame made out of water proof solid foam PVC bar of size 20 x 32mm, reinforced by 32 x 32mm - 2 Nos., for vertical made out of LVL (Laminated Veneer Lumber), core material of 32mm thick high density craft paper honey comb board, sandwiched on both sides with pre-laminated ABS sheet thickness of 1.5mm. PVC edge banding of size 0.45mm on the vertical sides. Hardware made out of steel coated butterfly hinges - 3 Nos., for each shutter and ISI make SS round lock complete for finished item of work, complete complying with the standard specification. The door shutter and frame should be got approved from the Deparmental officers before use on work (SOR No: M-0678) |
| 24 | Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Forest Officer before use on work |
| 25 | Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Departmetal officers before use on works.) |
| 26 | Supplying, fabricating, erecting and fixing Using perforated sheets (10mm thick)board false ceiling upto a ceiling height of 4.5m from floor level PWD SOR No. m-0619 |
| 27 | Supply and fixing of single box type 4'40 W flu fitting complete with copper choke and condensor with TW round blocks on wall or ceiling with flu tube with PVC unsheathed Copper leads from terminals to the fitting.S.D 89 |
| 28 | Supply and fixing of 1200 mm (48\\") AC ceiling fan complete with stepped electronic 300W regulator with 1 1 meter down rod on the existing clamp. S.D 110 |
| 29 | Wiring with 2 x 1.5 sq.mm.(22/0.3) PVC insulated SC unsheathed Cu. Contractor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceilig with PVC accessories, in flush with wall, with 150mm x 100mm x 113mm TW switch box with 3mm thick Hylem sheet cover for 5A 3 pin non inter locking CS plug with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour for concealed PVC plug point.(S.D 36) of PWD Electrical detailed data - P.V.C Plug Point ) |
| 30 | Wiring with 2 x 1.5 sq.mm.(22/0.3) PVC insulated SC unsheathed Cu. Contractor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceilig with PVC accessories, in flush with wall with 3mm thick Hylem sheet cover with TW switch box and 5A F.T switch and making good of the oncealed portion with suitable colour for PVC concealed light / Fan point (For electronic regulator ) (5points per coil (S.D 24) of PWD Electrical detailed data - Light Points & Fan Points 2024-2025 |
| 31 | Supply and fixing of fancy glass shade and 15 W LED Bulb Electriacal SD 80 |
| 32 | SOLAR PV PLANTOn Grid Solar PV Plant comprising of:i) Solar panels of type Mono Crystline, PERC, etc.ii) Power Conditioning Unit (PCU)with MPPT, Inverter,Controls, Protection Devices, Interconnecting D.C.cables, Connectors, Junction Boxes and accessories.iii) D.C. D.Biv) A.C. D.Bv) A.C. cables and accessoriesvi) Lightning arrestor, earthing, etc.vii) Module Metallic Mounting Structuresviii) Installation, Testing and Commissioning correspondsto BIS and IEC requirements (Ref. M-2359) |
| 33 | Supply and installation of a stone plaque 21/2 xn 21/2 feet depicting the details of name of scheme (SADP), name of the work, estimate cost, year of sanction, name of the Implementing Agency should be erected in a prominent and permanent location. (SADP Name should be highlighted in Golden Letters) Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 25, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 01, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 4 daysAug 01, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 4 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender