Tender For Rate Contract For Waterproofing In Both Academic And Residential Buildings For 12 Months Period (Work Has To Be Done In Piece Meal Wherever And Whenever Required Throughout The Period Of Agreement) At Nit Warangal.
Tender Value
36.82 Lakhs
Estimated cost
Bid Submission
14 Aug 2026
17 days left
EMD
73700
Bank guarantee accepted
Document Fee
1180
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Warangal Urban → Telangana
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Rate Contract For Waterproofing In Both Academic And Residential Buildings For 12 Months Period (Work Has To Be Done In Piece Meal Wherever And Whenever Required Throughout The Period Of Agreement) At Nit Warangal.
BOQ
| Sl. No. | Item Description |
| 1 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:1½:3 (1 Cement: 1½ coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 2 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm(thickness to be specified by the manufacturer) of 1st quality conformingto IS : 15622 of approved make in colours such as White, Ivory, Grey,Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with epoxy grout (to be paid seperately) etc., complete |
| 3 | Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in propershape,raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge With cement mortar 1:4 (1 cement : 4 fine sand) |
| 4 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) |
| 5 | Demolishing dry brick pitching in floors, drains etc. including stacking of serviceable material and disposal of unserviceable material within 50 metres lead : |
| 6 | Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. For thickness of tiles 10 mm to 25 mm. |
| 7 | Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. |
| 8 | Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. |
| 9 | Supplying and applying Wall Guard (Fosroc / Dr. Fixit / equivalent approved brand) on external walls wherever dampness is observed and as instructed by the Department, including all materials, labour, incidental and operational charges complete, in two coats over one coat of acrylic primer such as Nitoprime AW / Dr. Fixit Primeseal 604 / equivalent approved brand on old external wall surfaces.The operation shall be carried out after proper scraping and cleaning of the surface to remove loose particles using wire brushes. Cracks shall be filled with Nitoseal PU50 / Dr. Fixit PU Sealant / equivalent approved brand as directed by the Engineer-in-Charge.Procedure to be followed: 1.Surface Preparation: Surface shall be prepared by mechanical grinding to remove all loose mortar, laitance, oil, grease, decayed matter and algae growth. 2.Filling of Cracks: Identify cracks on the walls and chase them open in the form of grooves. Cutting of cracks shall be done to a size of 5 mm × 5 mm or as required. Fill the grooves properly with Nitoseal PU50 / Dr. Fixit PU Sealant / equivalent approved brand.3.Priming Coat: The prepared surface shall be applied with one coat of acrylic primer such as Nitoprime AW / Dr. Fixit Primeseal / equivalent approved brand prior to application of Wall Guard coating. The primer coat shall be air cured for 6 hours. 4.Wall Guard Application: Apply Wall Guard coating (Fosroc / Dr. Fixit / equivalent approved brand) in two coats at a minimum dry film thickness (DFT) of 110 microns per coat with a minimum consumption of 0.30–0.40 L/m². Each coat shall be air cured for 6 hours before application of the subsequent coat. (GST applicable as per DSR-2023).Note: The above work shall be carried out with the help of trained and skilled labour strictly as per manufacturer specifications. |
| 10 | Supplying and applying acrylic polymer modified elastomeric fibre reinforced waterproofing coating (Fosroc / Dr. Fixit / equivalent approved brand) in three coats with a total thickness of 1 mm DFT over one coat of acrylic primer such as Nitoproof WB / Dr. Fixit Primeseal 604 or equivalent approved brand on the roof surface, including all materials, labour, incidental and operational charges complete. The work shall be carried out after proper surface preparation by scrapping and cleaning the surface thoroughly to remove loose particles using wire brushes. Cracks shall be filled with Nitoseal PU50 / Dr. Fixit PU Sealant / equivalent approved brand as directed by the Engineer-in-Charge. 1. Surface Preparation: Surface shall be prepared by mechanical grinding to remove all loose mortar, laitance, oil, grease, decayed matter and algae growth.2. Filling of Cracks: Identify cracks on the surface and chase them open in the form of grooves. Cutting of cracks shall be done to a size of 5 mm × 5 mm or as required. Fill the grooves properly with Nitoseal PU50 / Dr. Fixit PU Sealant / equivalent approved brand. 3. Priming Coat: The prepared surface shall be applied with one coat of acrylic primer such as Nitoproof WB / Dr. Fixit Primeseal 604 / equivalent approved brand prior to application of waterproof coating. The primer coat shall be air cured for 6 hours.4. Waterproof Coating Application: Apply acrylic elastomeric waterproof coating (Fosroc / Dr. Fixit / equivalent approved brand) at a thickness of 1 mm DFT in three coats with minimum consumption of 1.2–1.5 kg/m². Each coat shall be air cured for 6 hours before application of the subsequent coat.(GST applicable as per DSR-2023).Note: The above work shall be carried out with the help of trained and skilled labour strictly as per manufacturer specifications. |
| 11 | Filling of Cracks: Identify cracks on the walls and roof surfaces and chase them open in the form of grooves. Cutting of cracks shall be carried out to a size of 5 mm × 5 mm or as required. The grooves shall be cleaned properly and filled with Nitoseal PU50 / Dr. Fixit PU Sealant / equivalent approved brand, a single-component low modulus gun-grade elastomeric sealant based on polyurethane technology.The applied sealant shall have a Movement Accommodation Factor (MAF) of 50% and Shore A Hardness of 32. The material shall possess an average peel strength of 220 N and peak peel strength of 260 N.(GST applicable as per DSR-2023) Note: The above work shall be carried out with the help of trained and skilled labour strictly as per manufacturer specifications. |
| 12 | Providing and injecting approved grout in proportions recommended by the manufacturer into cracks and honeycombed areas of concrete/RCC/masonry using suitable gun/pump at required pressure, including cutting of nipples after curing, complete as directed by the Engineer-in-Charge.(Payment shall be made on the basis of actual quantity/weight of approved grout injected.)Pressure grouting shall be carried out using Fosroc Cebex 100 / Dr. Fixit Pidigrout 10M or equivalent approved brand. The grout material shall comply with relevant standards and shall be injected using a suitable pressure grout pump at required locations as per manufacturer specifications.In case of Cebex 100, cement slurry shall be prepared by mixing Cebex 100 @ 225 g per 50 kg bag of cement before injection.(GST applicable as per DSR-2023)Note:The above work shall be carried out with the help of trained and skilled labour strictly as per manufacturer specifications. |
| 13 | Providing water-stopping crack injection resin foam using Nitofill WS60 / Dr. Fixit PU Injection Foam / equivalent approved brand, a two-component foaming liquid polyurethane resin, which when mixed in recommended proportions and injected into cracks in concrete/RCC shall react with moving water to form a foam water-stopping barrier, including drilling, fixing of injection nipples, pressure injection using suitable pump, cutting/removal of nipples after curing and sealing complete as directed by the Engineer-in-Charge. The resin shall have a pot life of 6–8 hours at 20°C in the absence of water, specific gravity of 1.14 ± 0.06 and foam density of 0.025.Payment shall be made on the basis of actual quantity/weight of approved grout injected (GST applicable as per DSR-2023). Note: The above work shall be carried out with the help of trained and skilled labour strictly as per manufacturer specifications. |
| 14 | Grouting the joints of new/existing flooring and wall tiles having joints of 3 mm width after removal of old/damaged joint filling material wherever required and proper cleaning of joints, using epoxy grout mix consisting of 0.70 kg of organic coated filler of approved shade mixed with 0.20 kg resin and 0.10 kg hardener per kg of filler, including filling, grouting, finishing and cleaning of excess material complete as directed by the Engineer-in-Charge. The epoxy grout shall be of approved make such as Nitotile GPX / Dr. Fixit Epoxy Tile Grout / Roff Epoxy Grout / equivalent approved brand.(GST applicable as per DSR-2023)Note:The above work shall be carried out with the help of trained and skilled labour strictly as per manufacturer specifications Size of Tile 300x300 mm to 500x500 mm |
| 15 | Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed Vitrified tiles Matt/Antiskid finish of size 600mm*600mm or 300mm*300mm |
| 16 | Providing and fixing unplasticised Rigid PVC SWR Single socketed pipes of 110mm & required fittings and specials conforming to IS : 13592 Type A (pressure of 4kg/sqcm) including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion including necessary fittings like ss clamps and plain bend with/without access door ,single/double equal/unequal junction of required degree with/without access door, terminal guard, heel rest bend etc complete as per direction of Engineer -in-Charge. (Note: 1. All the joints shall be leak proof .2. The centre line length of pipes shall be measured for the purpose of payment. 3.Floor trap only shall be measured separately for payment).110 mm dia. |
| 17 | Supplying and fixing of nahany trap of 4''(100mm) dia with grating for washroom floors and other locations |
| 18 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work Exposed on wall 20 mm nominal dia Pipes |
| 19 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work Exposed on wall 25 mm nominal dia Pipes |
| 20 | 12 mm cement plaster of mix 1:4 (1 cement: 4 fine sand) |
| 21 | Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar |
| 22 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:4 (1 cement : 4 coarse sand) Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 24, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 14, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 17 daysAug 17, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 20 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender