Tender For Development Of Park Near Phc In Village Lakhnola Ward No 15 In Municipal Corporation Manesar
Tender Value
50.26 Lakhs
Estimated cost
Bid Submission
03 Aug 2026
1 days left
EMD
1 Lakhs
Bank guarantee accepted
Document Fee
5000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Delhi → Delhi
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Development Of Park Near Phc In Village Lakhnola Ward No 15 In Municipal Corporation Manesar
BOQ
| Sl. No. | Item Description |
| 1 | Good Earth for filling un-even land [HSR 3.1.2 plus 17.8.2 plus 17.8.3] |
| 2 | MOVABLE NET POLE |
| 3 | (i) 6 No. Ornamental Design FRP pillar FRP base pedestal with vertical fitted design having base width of size 260mm x 260mm and height 900mm having 4 no. of size 15mm drilled in the base with hold fasts and having B class vertical m.s pipe of size 89 mm and height 2890mm, the central m.s pipe having FRP capital suitably mounted at appropriate height complete as per design enclosed. Complete pillar suitably grinded spray primered and subsequently spray painted with two coats of enamel paints is required shade. (ii) 12 No. spndred and 6 no. Friezes Floral and Ornate decorative design combination of spandrel and frieze, matched to be suspended between two m.s pillars as per the design copy enclosed. The spandrel (L-Bracker) having length 310mm and height 300mm the frieze (Top Panel) height 220mm and length as per the size of the gazebo. The frieze mounted on m.s tabular pipe frame of size 40mm x 25mm, frieze properly welded to the column pollars at either ends. Complete set of spandrel and frieze uniformly grinded spray primered, spray painted with two coats of enamel paint.(iii) 3 No. cast iron base panel railing with frame Floral and Ornate decorative design cast iron side railing panel as per design copy enclosed having height of 730mm and length as per size of Gazebo. Each panel top and bottom mounted with mild steel tubular pipe frame of size 40 x 25 mm. the bottom mild steel pipe having 3 nos. of hold fasts in m.s pipe of size 40 x 40mm and length 50mm welded at the base to hold the panel in the ground. The complete railing panel grinded for neat surface finishes spray primered and subsequently spray painted with two coats of enamel paint in required shade. (iv) One set of top frame with frp roof Top frame in m.s tubular pipe of size 40 x 40mm properly welded and grinded. The top frame mounted with FRP molded Sheet of 2 mm thick bent to profile on either ends with clear width installation of frp sheets fixed horizontally along the length between column pillars. Each sheet enamel painted in red color on both sides. Each such sheet properly riveted to horizontal sheets. The roof pipe frames properly primered and painted in red color. The complete item is without C.C floor and without sitting bench. rates are including with all taxes |
| 4 | -merry go round 4 seater 5dia main frame is m s sq pipe round pipe centrel pipe which further pipe supports with pipe ball bearing assembly chair made of molded frp plastic pu primer and pu paints |
| 5 | Supply and erection of 16 sqmm 4 Core Aluminium unarmoured Cable in existing pipe or trenches complete in all respect. |
| 6 | Providing And Installation Of Kids Play Equipment - Monkey BarAREA : 8 X 3.5 X 7 FEETAGE GROUP : 8-15 YRSM.S : 60 MM, 27 MMCAPACITY : 2-3“A” Class ISI marked MS Pipe of Reputed Brand (Jindal, Apollo, Bharat Etc).FRP Thickness between 3 To 8 mm.PU Coated Paint finish on the MS Structure.As Per Approved Design, including fixing In Ground With cement concrete at specifiedlocation till the satisfaction Of Engineer Incharge.As per reference image attached in annexure.Including GST and other Charges. |
| 7 | Leg Press: Providing designing and fixing of leg press of size 2000x550x1600 mm fabricated with main post of 114mm dia and 2.5mm thick and rest of the pipes 40mm dia and 2.5mm thick. All pipes made up of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nobel or equivalent of 80-120 micror thick |
| 8 | Twister:- Providing, and fixing Twister of size 1700 X 1300 X 1300 mm make of Green Gym or Equivalent fabricated with main post of 140 mm dia and 3.0 mm thick rest of the pipes are 40mm dia and 2.5 mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Padals shall be made up of Nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Officer-in-Charge. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and ishapod welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and approval of Officer -in-Charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of. equipment etc.`` ` |
| 9 | Double Cross Walker/ Cross trainer double:- Providing, and fixing Double Cross Walker of size 1600 X 600 X 1600 mm make of Green Gym or Equivalent fabricated with main post of 140 mm dia and 3.0 mm thick rest of the G.I pipes are 40 mm dia and 2.5 mm thick all G.I pipes made up of hot rolled tubular steel and hot dipped |
| 10 | Horse Rider Station:- Providing, and fixing of horse rider station of size 1000 x 600 x 1100 mm make of Green Gym or Equivalent fabricated with main post of 140 mm dia and 3.0 mm thick rest of the pipes are 40mm dia and 2.5 mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Alczo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Padals shall be made up Nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Engineer-in-Charge.Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shaped welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and a. .royal of arge regari ing materia , s ape of equipment,colour on metal, seat and |
| 11 | Pull Chair:- Providing, and fixing of Pull pair of size 2500 X 800 X 2000 mm make of Green Gym or Equivalent fabricated with main post of 140 mm dia and 3.0 mm thick rest of the pipes are 40mm dia and 3.0 mm thick all pipes made up of hot roiled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc .primer paint to be applied at all welding points prior to finishing. Pedals shall be made up of Nylon alloy with rounded edge of prevent any impact of injury and seat to be` made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Officer-in-Charge. Equipment to be fitted within b |
| 12 | Rowing machine: Providing designing and fixing rowing machine of size 1280x800x1150 mm fabricated with main past of 114 mm dia and 2.5mm thick and rest of the pipes 40mm dia and 2.5 mm thick. All pipes made up of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Handle bars are to be provided with high quality grip rubber Foothold shall be made up of nylon alloy with rounded edges to prevent any impact or injury and base cover to be made up from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic as 3mm colourful and UV resistant and environmental friendly. Bearing used shall be maintenance free duly oil sealed and self lubricated made by reputed company to be approved by Engineer in charge. Equipments to be fitted with inbuilt limiters to |
| 13 | Supply,Installation, testing and commissioning of water cooler (storage type ) fully stainless steel of 150/150 ltrs capacity as per IS standards with all accessories. as per site requirment suitable for operation on 230 V plus /- 10% , 50 Hz, single phase AC supply complete as reqd. Make Blue Star/ Sidwal/ Usha etc. The work includes PVC connection, control cable with plug top, drain pipe by making hole and chase cutting wherever it required as per site and repair the same with original finish etc as reqd (For Auditorium) |
| 14 | Specially Abled People Arm extension Fitness ApparatusProviding and fixing the following outdoor fitness equipment’s designed for minimum 100kg user Weight confirming to the required standard for safety and quality as perDIN/ASTM /CPSC/European standard / BIS The equipment shall be confirming to thespecification as below:-a) All the equipment shall be Third Party Quality certified as per the specifiedstandard.b) Nuts and Bolts- Stainless steel 316 and lock-nutc) Material – Galvanized steel Pipe cleaned by stand-blasting then coated withphosphate solution and finished with electro-static powder coating or othersimilar available material meeting the required standardd) Anti-rust Shoot blast /grit blasting of equipment to clean the rust Electrostaticpowder coating technique To process the pipe surfacee) Column the mild steel pipe column footing plate screw with a pull-burst, thesurface rust acid decreasing cleaning phosphate rust. After a special process,throwing sand imported plastic powder with a double surface household- levelspraying layer, electrostatic spray, high-temperature plastic 200 degree bakingpowder smooth surface UV resistant or as specified by the manufacture’sspecificationf) Seat and plastic LLDPE/HDPE metal with any protection / composite materialwith any protection infiltration of anti-static de-colorization element passing,strength, smooth surface, Security assurance weather resistant etc.g) UV-fully resistantPlatforms- High strength punching plate with special process dealing with wavy surfacemicroscopy, safe and beautiful non-slip resistanceFasteners – stainless steel screw to be used and at the contact point with the columns-rubbers pads to be used , screw top cover with a plastic cap, to enhance its security Theinstallation of the equipment’s shall be carried out on cement concrete foundation ofminimum size 700 mm x 700mm x 700 mm and / or size approved by Engineer-in-chargeof mix 1:1:5:3(1 cement 1.5 coarse sand 3 graded stone aggregate of 20 mm nominal size )The cost for equipment shall include the required foundation bolts of 18 mm dia and ofrequired shape and length as per sample approved by Engineer-in-charge however the cost for earth work and CC shall be paid for separately .The rates Quoted for the put door fitnessequipment’s shall be inclusive of 1st Year comprehensive maintenancespecifications:-. Fabricated with main post of NB 100mm (G.I) “A” Class Pipe of approvedmake. Main frame of NB 65mm (G.I) “A” Class pipe. Handle support frame of NB 50mm (G.I)“A” Class pipe. (‘NB’ stands for Nominal Bore i.e., internal Diameter of pipe in millimetres).All pipes are powder coated with 80-120 micron thick Akzo Nobel or equivalent paints. Alljoints of pipe are robotic welded with joints scalloped as necessary and dressed off removingsharp edges and burrs. Zinc primer paint is applied at all the welding points prior tofinishing. Base plate cover made of virgin LLDPE plastic by rotational moulding withminimum 4.00mm thickness, UV resistant and coloured. Foothold made of NB 25mm (G.I)“A” Class pipe. Seat to be made up from virgin LLDPE plastic by rotational moulding withminimum 4.00mm thickness,coloured, UV resistant and environmental friendly.Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated areused in the equipment manufactured. The equipment are fitted with inbuilt limiters toprevent unwanted movements. The equipment is fixed on ground with concrete of minimumstrength M-25 and J shaped welded bolts of 18mm thickness. Once the concrete is set, theequipment is fixed on to it and nuts and bolts are covered with base plate cover. High tensilesteel with galvanized nut bolts are used for assembly.Equipment must be made and confirms with the approved standards certified by andcertificates are mandatory requires in the name of both Tenders act as bidder andmanufacturer.1. IS 178012. ISO 180013. ISO 27001:20134. ISO 50001:20185. ISO 13485:20166. ISO 45001:20187. ISO 14001:20158. ISO 9001:20159. ISO 14001:200410. ISO 9001:200811. EN 1490412. EN-1176-1-201713. EN 16630:201514. EN 1663015. EN 95716. EN 9100:201617. EN 11630:201718. GS19. DIN 18032.220. DIN 79000-201221. CE Certificate22. CE 1199323. OHSAS 18001:201724. SLBR 6225. BIFMA26. GMP27. RoHSThe equipment must accompained with Test report for Quality, Safety, Durability andProper Functioning of Equipment must mandatory requires Test report in the nameof both Tenderer act as bidder and manufacturer.1. Test Report of SS Nut and Bolts2. Test Report of LLDPE Base Caps for Open Gym3. Test Report of Powder Coating Pipe4. Test Report of SKF Bearing No. 6007-2Z 5. Test Report of FRP/Plastic (Fiber Pad)6. Test Report of Welding Pipe (Robotic MIG Welding)7. Test Report of MEK Solvent8. Test Report of Neutrul Salt Spray Test9. Test Report of Breaking Load of Welding Pipe10. Test Report of GI Pipe 100 mm NB11. Test Report of GI Pipe 80 mm NB12. Test Report of GI Pipe 50 mm NB13. Test Report of GI Pipe 32 mm NB14. Test Report of GI Pipe 25 mm NB |
| 15 | Specially Abled People Pull Chair with Cycle Combination Fitness ApparatusA pull chair, also known as a pull-wheelchair, combines the functionality of a standardwheelchair with a cycling feature, allowing the user to propel themselves using their handson the rear wheels. Cycle-handicapped wheelchairs, on the other hand, are typicallypowered by hand cranks.a) All the equipment shall be Third Party Quality certified as per the specifiedstandard.b) Nuts and Bolts- Stainless steel 316 and lock-nutc) Material – Galvanized steel Pipe cleaned by stand-blasting then coated withphosphate solution and finished with electro-static powder coating or othersimilar available material meeting the required standardd) Anti-rust Shoot blast /grit blasting of equipment to clean the rust Electrostaticpowder coating technique To process the pipe surfacee) Column the mild steel pipe column footing plate screw with a pull-burst, thesurface rust acid decreasing cleaning phosphate rust. After a special process,throwing sand imported plastic powder with a double surface household- level spraying layer, electrostatic spray, high-temperature plastic 200 degree bakingpowder smooth surface UV resistant or as specified by the manufacture’sspecificationf) Seat and plastic LLDPE/HDPE metal with any protection / composite materialwith any protection infiltration of anti-static de-colorization element passing,strength, smooth surface, Security assurance weather resistant etc.g) UV-fully resistantspecifications:-. Fabricated with main post of NB 100mm (G.I) “A” Class Pipe of approvedmake. Main frame of NB 65mm (G.I) “A” Class pipe. Handle support frame of NB 50mm (G.I)“A” Class pipe. (‘NB’ stands for Nominal Bore i.e., internal Diameter of pipe in millimetres).All pipes are powder coated with 80-120 micron thick Akzo Nobel or equivalent paints. Alljoints of pipe are robotic welded with joints scalloped as necessary and dressed off removingsharp edges and burrs. Zinc primer paint is applied at all the welding points prior tofinishing. Base plate cover made of virgin LLDPE plastic by rotational moulding withminimum 4.00mm thickness, UV resistant and coloured. Foothold made of NB 25mm (G.I)“A” Class pipe. Seat to be made up from virgin LLDPE plastic by rotational moulding withminimum 4.00mm thickness,coloured, UV resistant and environmental friendly.Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated areused in the equipment manufactured. The equipment are fitted with inbuilt limiters toprevent unwanted movements. The equipment is fixed on ground with concrete of minimumstrength M-25 and J shaped welded bolts of 18mm thickness. Once the concrete is set, theequipment is fixed on to it and nuts and bolts are covered with base plate cover. High tensilesteel with galvanized nut bolts are used for assembly.Equipment must be made and confirms with the approved standards certified by andcertificates are mandatory requires in the name of both Tenders act as bidder andmanufacturer.1. IS 178012. ISO 180013. ISO 27001:20134. ISO 50001:20185. ISO 13485:20166. ISO 45001:20187. ISO 14001:20158. ISO 9001:20159. ISO 14001:200410. ISO 9001:200811. EN 1490412. EN-1176-1-201713. EN 16630:201514. EN 1663015. EN 95716. EN 9100:201617. EN 11630:201718. GS19. DIN 18032.220. DIN 79000-201221. CE Certificate22. CE 1199323. OHSAS 18001:201724. SLBR 6225. BIFMA26. GMP27. RoHSThe equipment must accompained with Test report for Quality, Safety, Durability andProper Functioning of Equipment must mandatory requires Test report in the nameof both Tenderer act as bidder and manufacturer. 1. Test Report of SS Nut and Bolts2. Test Report of LLDPE Base Caps for Open Gym3. Test Report of Powder Coating Pipe4. Test Report of SKF Bearing No. 6007-2Z5. Test Report of FRP/Plastic (Fiber Pad)6. Test Report of Welding Pipe (Robotic MIG Welding)7. Test Report of MEK Solvent8. Test Report of Neutrul Salt Spray Test9. Test Report of Breaking Load of Welding Pipe10. Test Report of GI Pipe 100 mm NB11. Test Report of GI Pipe 80 mm NB12. Test Report of GI Pipe 50 mm NB13. Test Report of GI Pipe 32 mm NB14. Test Report of GI Pipe 25 mm NB |
| 16 | Specially Abled People Wave Balance Fitness Apparatus1. Size: 2386 x 136 x 1795mm2. Constructed with weather-resistant powder-coated steel and anti-slip wave-shaped foot platform.3. Platform length: 1800 mm: width: 400 mm: height variation simulates gentle wavemotion.4. Includes dual side handrails (height: 900 mm) with 42 mm diameter for stabilityand grip.5. Supports up to 150 kg user weight: fixed to ground with anti-rust anchor bolts.6. Enhances balance, coordination, and lower limb control for senior users in outdoorsettings.7. All the equipment shall be Third Party Quality certified as per the specifiedstandard.8. Nuts and Bolts- Stainless steel 316 and lock-nut9. Material – Galvanized steel Pipe cleaned by stand-blasting then coated withphosphate solution and finished with electro-static powder coating or othersimilar available material meeting the required standard10. Anti-rust Shoot blast /grit blasting of equipment to clean the rust Electrostaticpowder coating technique To process the pipe surface11. Column the mild steel pipe column footing plate screw with a pull-burst, thesurface rust acid decreasing cleaning phosphate rust. After a special process,throwing sand imported plastic powder with a double surface household- levelspraying layer, electrostatic spray, high-temperature plastic 200 degree bakingpowder smooth surface UV resistant or as specified by the manufacture’sspecification12. Seat and plastic LLDPE/HDPE metal with any protection / composite materialwith any protection infiltration of anti- static de-colorization element passing,strength, smooth surface, Security assurance weather resistant etc.13. UV-fully resistantPlatforms- High strength punching plate with special process dealing with wavy surfacemicroscopy, safe and beautiful non-slip resistanceFasteners – stainless steel screw to be used and at the contact point with the columns-rubbers pads to be used , screw top cover with a plastic cap, to enhance its security Theinstallation of the equipment’s shall be carried out on cement concrete foundation ofminimum size 700 mm x 700mm x 700 mm and / or size approved by Engineer-in- chargeof mix 1:1:5:3(1 cement 1.5 coarse sand 3 graded stone aggregate of 20 mm nominal size )The cost for equipment shall include the required foundation bolts of 18 mm dia and ofrequired shape and length as per sampleapproved by Engineer-in-charge however the cost for earthm work and CC shall be paid forseparately .The rates Quoted for the put door fitnessspecifications:-. Fabricated with main post of NB 100mm (G.I) “A” Class Pipe of approvedmake. Main frame of NB 65mm (G.I) “A” Class pipe. Handle support frame of NB 50mm (G.I)“A” Class pipe. (‘NB’ stands for Nominal Bore i.e., internal Diameter of pipe in millimetres).All pipes are powder coated with 80-120 micron thick Akzo Nobel or equivalent paints. Alljoints of pipe are robotic welded with joints scalloped as necessary and dressed off removingsharp edges and burrs. Zinc primer paint is applied at all the welding points prior tofinishing. Base plate cover made of virgin LLDPE plastic by rotational moulding withminimum 4.00mm thickness, UV resistant and coloured. Foothold made of NB 25mm (G.I)“A” Class pipe. Seat to be made up from virgin LLDPE plastic by rotational moulding withminimum 4.00mm thickness,coloured, UV resistant and environmental friendly.Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated areused in the equipment manufactured. The equipment are fitted with inbuilt limiters toprevent unwanted movements. The equipment is fixed on ground with concrete of minimumstrength M-25 and J shaped welded bolts of 18mm thickness. Once the concrete is set, theequipment is fixed on to it and nuts and bolts are covered with base plate cover. High tensilesteel with galvanized nut bolts are used for assembly.Equipment must be made and confirms with the approved standards certified by andcertificates are mandatory requires in the name of both Tenders act as bidder andmanufacturer.1. IS 178012. ISO 180013. ISO 27001:20134. ISO 50001:20185. ISO 13485:20166. ISO 45001:20187. ISO 14001:20158. ISO 9001:20159. ISO 14001:200410. ISO 9001:200811. EN 1490412. EN-1176-1-201713. EN 16630:201514. EN 1663015. EN 95716. EN 9100:201617. EN 11630:201718. GS19. DIN 18032.220. DIN 79000-201221. CE Certificate22. CE 1199323. OHSAS 18001:201724. SLBR 6225. BIFMA26. GMP27. RoHSThe equipment must accompained with Test report for Quality, Safety, Durability andProper Functioning of Equipment must mandatory requires Test report in the nameof both Tenderer act as bidder and manufacturer.1. Test Report of SS Nut and Bolts2. Test Report of LLDPE Base Caps for Open Gym3. Test Report of Powder Coating Pipe4. Test Report of SKF Bearing No. 6007-2Z5. Test Report of FRP/Plastic (Fiber Pad)6. Test Report of Welding Pipe (Robotic MIG Welding)7. Test Report of MEK Solvent8. Test Report of Neutrul Salt Spray Test9. Test Report of Breaking Load of Welding Pipe10. Test Report of GI Pipe 100 mm NB11. Test Report of GI Pipe 80 mm NB12. Test Report of GI Pipe 50 mm NB13. Test Report of GI Pipe 32 mm NB14. Test Report of GI Pipe 25 mm N |
| 17 | -Analysis of Rate for Sport floor-Flex Court System-8 Layers, Over the Asphalt Surface |
| 18 | Development of Park near PHC in village Lakhnola ward no 15 in Municipal Corporation Manesar Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 25, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 03, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 1 dayAug 03, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 1 dayTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender