Tender For special Repair To Building No P-05 At Zangli, Provn Of Sentry Post And Deep Freezer Under The Aor Of Ge 874 Ews.
Tender Value
Ref. Documents
Estimated cost
Bid Submission
27 Aug 2026
3 days left
EMD
67300
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Kupwara → Jammu and Kashmir
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for special Repair To Building No P-05 At Zangli, Provn Of Sentry Post And Deep Freezer Under The Aor Of Ge 874 Ews.
Corrigendum
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 10-Aug-2026 | Date Corrigendum | Date | 22-Aug-2026 |
| 2 | 16-Aug-2026 | Revised BOQ | BOQ | 27-Aug-2026 |
| 3 | 10-Aug-2026 | Date Corrigendum | Date | 22-Aug-2026 |
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of brick work or stone masonry built in cement mortar including all quoins, pillars, arches etc. but excluding ashlar facings, dressed stone work and precast concrete articles, complete all as specified and as directed. |
| 2 | Dismantling floor, hearth or wall tiles including cement mortar bedding complete, removing serviceable tiles to store and rubbish off the premised complete all as specified and directed. |
| 3 | Demolition of cement concrete (unreinforced) in ground floors and paving not exceeding 15 cm thickness (below or above ground level) complete all as specified and as directed. |
| 4 | M&L for cement concrete type B-0,1:2:4 (20mm graded aggregate) 25 mm thick as in sub base for floor finishes, drain channels complete all as specified and as directed. |
| 5 | M&L for Vitrified ceramic tiles 10 mm thick (square/ rectangular)of light/dark shade polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match in neat cement slurry and pointed in white or coloured cement to match over 10 mm thick screed bed in CM 1:4 & Joints will be of uniform thickness not exceeding 2 mm and these shall be grouted with Solid Epoxy Grout of desired shade as per manufacturer’s instructions. complete all as specified and directed. |
| 6 | All as per item No 6 above but on vertical surface such as skirting, dados, risers to steps, etc., set and jointed in neat cement slurry and pointed in coloured cement to match tiles, over and including 10 mm thick rendering in cement mortar 1:4 complete all as specified and directed. |
| 7 | M&L Non - skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to matchr and including 1o mm thick screed bed in cement mortar 1:4 for laying floor finishes & Joints will be of uniform thickness not exceeding 2 mm and these shall be grouted with Solid Epoxy Grout complete all as specified and directed. |
| 8 | M & L for Ist or premium or standard quality of glazes, ceramic “coloured” tiles of premium or first quality of size 450x300x7 mm thick as in vertical surface suck as skirting/dado etc set and jointed in neat cement slurry and pointed in white or colour cement to match over 10mm thick in 1:4 cm backing coats etc complete all as specified and directed. |
| 9 | Demolition of stone slabs and tiles of any description or thickness in floors bedded and laid in any cement mortar, aprons etc. complete all as specified and as directed. |
| 10 | M&L for 20 cm x 20cm x 25 mm thick Chequered cement concrete tiles (in any colour & shape), set, jointed and pointed in neat cement slurry in floors with grey cement pigment over 15 mm screed bed in CM 1:4 complete all as specified & directed. |
| 11 | M&L Cement concrete 1:3:6 type C1 20mm graded stone aggregate as bed block to hold fast block and other similar works etc |
| 12 | M&L for Cement concrete 1:4:8 type D-2, 40mm graded stone aggregate as in foundation filling, and mass concrete etc complete all as specified and as directed. |
| 13 | M&L for cement concrete 75 mm thick, type C-1, 1:3:6 (20mm graded aggregate) as in plinth protection finished even and smooth without using extra cement complete all as specified and as directed. |
| 14 | M&L for cement concrete 75 mm thick, type C-2, 1:3:6 (40mm graded aggregate) as in sub base, foundation, filling and mass concrete etc complete including demolition of cement concrete all as specified and directed |
| 15 | M&L for Pre- painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed. |
| 16 | M&L for pre- painted galvalume aluminium zinc coating GI based plain sheet 0.63 mm thick of an colour having tensile strength of 550 Mpa profiled as ridge, roof covering/cladding to wall, formed in shape of water channel fixed with self tapping screws complete all as specified and as directed. |
| 17 | Dismantling of wall and ceiling boards including supply and fixing of 2nd class soft wood wall panelling of good quality wood planed one side and edges tonged and grooved or rebated other side and dovetailed joints chamfered both sides fixed to frame work with secret nailed as in wall panelling 12 mm including cornice and beading as required and applying two coat of varnish over a filler coat of thinner varnish after preparation of surface, complete all as specified and directed Note-: frame work shall be measured and paid separately. |
| 18 | S & F in repairs 9 mm thick Plywood, grade BWR, type BB, fixed with nails to timber frame work in wall/ceiling complete all as specified and as directed. |
| 19 | M&L for 2nd class soft wood Plain fillets. Exc 3 n exc 6 Sqcm square, rectangular or triangular in section, clean sawn, secured with screw complete all as specified and as directed. |
| 20 | Supply and Fix in repairs 18/19mm thick prelaminated particle board, interior/exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and directed, |
| 21 | S & F for clean sawn 25 mm thick 2nd class softwood with butt joints boarding, fixed with nails in facia including dismantling of boarding in any situation complete all as specified and directed. |
| 22 | S & F weather boarding, clean sawn, plain, 20mm thick or feather edged 15 mm to 20mm thick and fixed with 30mm laps including dismantling of boarding in any situation complete all as specified and directed |
| 23 | Taking down chowkats or frames with shutters (W/O taking off shutters) exc 1.5 sqm but n exc 4 sqm each complete all as specified and as directed. |
| 24 | Taking down chowkats with shutters (without taking off shutters from the frame) n exc. 1.50 sqm each complete all as specified and as directed. |
| 25 | S & F 2nd class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed |
| 26 | M&L for Aluminium sliding three track window with powder coated aluminium (minimum thickness of powder coating 50 micron) frame of aluminium section 62.5mm x 37mm x 1.5mm thick with two glass shutters with solar control black film and one mosquito proofing shutters with but 0.56 mm nominal dia of wire and average width of aperture1.18mm having style and rails of aluminium section 47.62mm x 44.45mm x 1.5mm thick including joining cleats, glazing clips, rubber packing, aluminium snap beading, screws anodized aluminium fittings such as hinges, tower bolts, handle etc., including 5.5 mm thick sheet glass& wire netting fixed in repairs, complete all as specified and directed. |
| 27 | S & F in repair aluminium panelled door single leaf with powder coated aluminium (minimum thickness of powder coating 50 micron) frame of section size 62.5mm x 37mm x 1.5mm thick, shutter with middle and bottom rail of aluminium section 112.5mm x 37mm x 1.5mm thick and stiles and top rails of aluminium section 83mm x 37mm x 1.5mm thick with suitable locking arrangement with lock (Make: Godrej / Link) 7 levers and self closing devices with rebates including joining cleats of suitable section for fixing and including provision of builders hardware fittings as required, door spring and glazing with 5.5mm thick ordinary coloured glass with film, including provision of EPDM rubber / neoprene gasket as required, including provision of necessary fittings, fixtures etc., complete all as specified and directed. |
| 28 | S&F Anodised aluminium frame for doors, windows, ventilators, Partitions with one or more rebates including joining cleat for fixing etc. complete all as specified complete all as specified and directed. |
| 29 | Hacking out old broken glass any thickness size, quality or description from wooden/steel frames fixed with wooden beads/metal pinning and S & F 4 mm thick selected sheet glass in squares not exc 0,5 sqm in each pane fixed with aluminium beading and EPDM rubber gasket (in metal frames etc), complete all as specified and directed. |
| 30 | Dismantling timber scantlings 40 sq. cm and over in section, in any position for unframed/Framed work complete including supply and fixing of second class clean sawn soft-wood in scantlings all as specified and directed. |
| 31 | Dismantling timber scantlings 40 sq. cm and over in section, in any position for unframed/Framed work complete including fixing of second class clean sawn soft-wood in scantlings except timber complete all as specified and as directed. |
| 32 | S&F factory made plain framed, panelled shutter 35mm thick made of 2nd class soft wood of 35 mm thick (two panels)with lock rail and panel of 12 mm veneered particle board with commercial veneering on both faces. The size of rail and styles as per IS: 1003 (Part-I), kiln seasoned and chemically pressure treated. |
| 33 | S&F 35mm thick glazed and skeleton shutters open rebated and prepared to receive gauze, wire netting etc (without sash bar) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc sizes of members of shutters as specified in SSR Pt-I Sec 8 Clause 8.20 (a) in 2nd class soft wood complete all as specified and as directed. |
| 34 | S&F in repair. Galvanized mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and as directed. |
| 35 | S&F 75 mm size butt hinges cast brass, medium weight, with mild steel hinge pin, bright polished and fixed, type B-11 complete all as specified and as directed. |
| 36 | S&F 100 mm size stainless steel butt hinges, medium weight, cold rolled etc complete all as specified and as directed. |
| 37 | S&F 100mm extruded aluminium alloy handles, fabricated type anodised complete all as specified and as directed. |
| 38 | S&F 150 mm extruded aluminium alloy handles, fabricated type anodised complete all as specified and as directed. |
| 39 | S&F 150 mm long aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and as directed. |
| 40 | S&F 300 mm aluminium alloy, anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast of extruded sections and fixing bolts and sliding bolts of extruded sec or cast aluminium and fixed complete all as specified and as directed. |
| 41 | S&F 200 mm aluminium alloy, anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast of extruded sections and fixing bolts and sliding bolts of extruded sec or cast aluminium and fixed complete all as specified and as directed. |
| 42 | S & F in repair floor door stopper of aluminium alloy body and tongue, anodized, with hard drawn steel spring, fixed in floor with over all (length of cover plate 140 mm) complete all as specified and directed. |
| 43 | S & F in repairs Door closer aluminium (extruded section only) hydraulically regulated, designation No. 2, universal type, suitable for door shutters of 750 to1200 mm in width and of weight between 36 to 60 kg and fixed complete all as specified and as directed. |
| 44 | Supply only integral water proofing compound complete all as specified and as directed. |
| 45 | M&L for rendering 10mm thick on fair faces of brick work or concrete surfaces in CM 1:6 is to be finished even and smooth (without using extra lime or cement) including taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, of any description etc& preparing new plastered surfaces of wall and applying two coats of 1st quality acrylic distemper having VOC content less than 50 gms/litre, of approved manufacturer over chalk whiting, white or tinted complete all as specified and as directed. |
| 46 | M&L rendering 15mm thick on fair faces of brick work/stone masonry surfaces or concrete surfaces in CM 1:4 is to be finished even and smooth with water proofing compound (without using extra lime or cement), including taking down cement plaster on brick or stone walls including raking out joints, hacking for key, scrubbing down with water, of any description etc & preparing new plastered surfaces of wall and applying two coats of cement base paint over a coat of alkali resistance primer complete all as specified and as directed. |
| 47 | M&L rendering 15mm thick on other than fair faces of brick work or concrete surfaces in CM 1:4 is to be finished even and smooth with water proofing compound (without using extra lime or cement) including necessary scaffolding & taking down of cement plaster complete all as specified and as directed. |
| 48 | M&L for complete removal of existing treatment from walls (any number of layers) by scrapping with steel scrappers or any other means, including filling depressions of scrapped surfaces and applying two coats of cement base paint, over a coat of alkali resistance primer with preparation of plastered surfaces complete all as specified and directed. |
| 49 | M & L for applying two coats of synthetic enamel paint on new/old wooden surfaces of any description over 10 cm width or girth over a coat of pink primer including preparation of surfaces complete all as specified and as directed. |
| 50 | S&F 110mm bore, PVC (SWR) pipes, single socket in any length, with rubber ring joints laid in trenches or in floors complete all as specified and as directed. |
| 51 | S&F 75 mm bore, PVC (SWR) pipes, single socket in any length, with rubber ring joints fixed on walls complete all as specified and as directed. |
| 52 | S & F PVC (SWR) bends any radius, 110mm bore, complete all as specified and as directed. |
| 53 | S & F PVC (SWR) junction single T (equal or unequal) with access door any radius, 110mm bore complete all as specified and as directed. |
| 54 | S & F PVC (SWR) junction single T (equal or unequal) with access door any radius, 75 mm bore complete all as specified and as directed. |
| 55 | S & F PVC (SWR) bends with access door any radius, 110 mm bore complete all as specified and as directed. |
| 56 | S & F PVC (SWR) bends any radius, 75 mm bore complete all as specified and as directed. |
| 57 | S & F PVC (SWR) reducers 75/110 mm bore complete all as specified and as directed. |
| 58 | S & F PVC (SWR) Couplers 75/110 mm bore complete all as specified and as directed. |
| 59 | S & F PVC (SWR) vent cowl cone type 80/110 mm bore complete all as specified and as directed. |
| 60 | S & F in repair vitreous China wash basin with pedestal , white, flat back, size 550 x 400 mm with capstan heads, chromium plated, one No PVC waste pipe 25 mm dia and 75 cm long with 32 mm dia connector, 32mm size waste fittings, brass chromium plated with long screwed shanks and fly nuts, flange end, bedded in red lead cement and other fixer complete including cutting for and pinning in ends of bracket or erecting stand complete all as specified and directed. |
| 61 | M&L for central hole basin mixer, 15mm bore, with popup waste, chromium plated, screwed down for galvanised iron pipes, fixed in repairs, complete all as specified and directed. |
| 62 | S &F in repair 15 mm dia Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed. |
| 63 | S & F in repairs cabinet mirror of size 450x350mm made with 5mm thick pvc sheet coloured or white and fixed to wall complete all as specified and as directed. |
| 64 | S&F in repairs corner glass shelf made of 12mm thick glass, 250mm radius between flanges of brass chromium plated D clamps complete all as specified and as directed. |
| 65 | S&F in repairs PVC connection 600mm long with check nut etc complete all as specified and as directed. |
| 66 | M&L curtain rails, stainless steel, with fixing brackets, Knobs, rollers etc. complete all as specified and as directed. |
| 67 | M&L for galvanised steel tubes medium grade 15 mm dia fixed to wall or ceiling or laid under floor, complete with necessary fittings including taking down complete all as specified and as directed. |
| 68 | M&L for galvanised steel tubes medium grade 20 mm dia fixed to wall or ceiling or laid under floor, complete with necessary fittings including taking down complete all as specified and as directed. |
| 69 | S&F in repairs 15mm dia chromium plated fancy type Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed. |
| 70 | S&F in repairs 15mm dia chromium plated fancy type concealed Stop valves/angle valve, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed. |
| 71 | S&F in repair stainless steel Soap dish, fixed to plugs with chromium plated brass screws complete all as specified and directed. |
| 72 | S&F in repair 10 litres capacity, PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and directed. |
| 73 | S&F in repairs Brass chromium plated shower rose with or without swivel joints, any size, including fixing to steel pipe or union 125mm size complete all as specified and directed. |
| 74 | S&F in repairs Brass chromium plated Tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and directed. |
| 75 | S&F in repairs Health faucet (ABS Body) mild steel chromium plated suitable for 15mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connection and fixed in position complete in all respect as specified |
| 76 | S&F in repairs vitreous China wash down water closet white (excluding fixing bolts, flushing cistern and flush pipe), fixing seat cover including connection to drain (or outgoing pipe, and to flushing pipe & anti syphonage pipe etc with aluminium hinging device complete. Note : Plastic seat cover shall be measured separately as Supply only under respective items. |
| 77 | Supply only water closet plastic seat cover closed pattern with flat bottom and cover with steel pin hinging device and fixed on EWC, complete all as specified and directed. |
| 78 | Supply & fixing in repair in position, 6 mm thick E board (classic) of size 610x610 mm as in false ceiling fixed with aluminium snap grid frame work of same size as aluminium Tee of size 25x25x1.50mm as main runner, 25x25x1.25 mm thick aluminium Tee as cross runner and aluminium angle of size 25x25x1.25mm at the perimeter including GI 3 mm adjustable suspender of required length of any description complete all as specified and directed. |
| 79 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed. |
| 80 | S & F 410 -W (Gde-E-250) quality-A, rolled section as in main and cross beam hip and jack rafter, purlins where connected to common rafter and running rails including distance pieces, cleats etc. complete all as specified and as directed. |
| 81 | S& F Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embedding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 |
| 82 | M & L for mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290. Gde-E-165 complete all as specified and as directed. |
| 83 | S&F in repair rotational moulded HDPE water storage tanks (cylindrical vertical with closed top) of 1000 litres capacity, ISI marked, double layered hoisted and fixed in position including connecting up pipes including ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe and fixed for 20 mm bore size (minimum weight 210gms) complete all as specified and directed. |
| 84 | S&F PVC (SWR) pipes 150mm dia single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed. |
| 85 | S & F in repair gun-metal, globe or gate valves of 15/20mm dia, with iron wheel head, screwed both ends for iron pipe and fixed etc complete all as specified and directed. |
| 86 | S&F in repair 75 mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement concrete 1:2:4, type B-1 (using 20 mm graded crushed stone aggregate) complete all as specified and as directed. |
| 87 | M&L for Pre cast Reinforced cement concrete type B1 1:2:4 cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces set in cement mortar 1:4 complete all as specified and directed. |
| 88 | M&L for use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed. |
| 89 | M&L for mild steel TMT bars 6mm to 8mm dia cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. |
| 90 | M&L for excavation in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspit, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out.in soft/Loose soil complete all as specified and directed. |
| 91 | M&L for returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm.in soft/Loose soil complete all as specified and directed. |
| 92 | M&L for removing excavated material/soil n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed. |
| 93 | M&L for construction of Soakage well, of size 1.20 m dia at bottom and 3.00 m effective depth complete all as specified and shown on drawing No. CESZ-TD-/2015 sheet No 1/3 & 3/3 dated 22 Feb 2015 (Revised dt 21 Mar 2015) and specified in particular specifications. |
| 94 | M&L for mild steel bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed. |
| 95 | M&L for lagging on pipe of internal dia 15/20mm used in internal water supply or plumbing all round with, 40 mm min thick bonded mineral wool preformed ‘SNAP ON’ pipe sections of density 144 Kg/cum conforming to IS 9843 complete all as specified and as directed. |
| 96 | All as per item no 90 above but for additional 1.50m or there part of in depth beyond the first 1.50 mtr. |
| 97 | M & L for RCC M-30 design mix (20 mm Graded aggregate) in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and as directed. |
| 98 | M & L for RCC M-30 design mix (20 mm Graded aggregate) in Columns, pillars, piers, posts and struts concrete complete all as specified and as directed. |
| 99 | M & L for RCC M-30 design mix (20 mm Graded aggregate) in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and as directed. |
| 100 | M & L for RCC M-30 design mix (20 mm Graded aggregate) in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed. |
| 101 | M & L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and as directed. |
| 102 | M & L for formwork to sides of pillars, posts, struts, piers, columns and stanchions complete all as specified and as directed. |
| 103 | M & L for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. complete all as specified and as directed. |
| 104 | M & L for TMT mild steel bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed. |
| 105 | M & L for 15 mm thick rendering on other fair faces of brick work or concrete surfaces in CM 1:6, rendering finishes even and smooth (without using extra cement) complete all as specified and as directed. |
| 106 | M & L for 15 mm thick rendering on fair faces of brick work or concrete surfaces in CM 1:4, on external wall finished even and fair mixer with integral water proofing compound @ 3% by weight of cement or in the manner specified by the manufacture and in the proportion indicated complete all as specified and as directed. |
| 107 | Supply only liquid water proofing compound all as specified and directed |
| 108 | M & L rendering 5 mm thick in CM 1:3 on fair faces of brick work or concrete surfaces as in roof slab etc all as specified and directed |
| 109 | M & L for preparation of newly plastered or un plastered surfaces and applying two coats of distemper oil emulsion white tinted complete all as specified and directed |
| 110 | M & L for preparation of newly plastered or un plastered surfaces and applying two coats of cement base paint complete all as specified and directed |
| 111 | M & L for mild steel works as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. complete all as specified and directed |
| 112 | M & L for non asbestos fibre cement building boards fixed or laid/ inserted to timber/GI/Aluminium framework with screws of minimum size 605 x 605 mm as in ceiling complete all as specified and directed |
| 113 | M & L for Gl frame work for seamless ceiling comprising of Gl perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to entre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx. 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre complete all as specified and directed |
| 114 | M L for preparing new plaster surfaces and non asbestos fibre cement building boards of ceiling and applying three coats of white wash complete all as specified and directed |
| 115 | M L for Hardcore of gauge exc 63mm but n exc. 100 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rolled/rammed to a true surface complete all as specified and directed |
| 116 | M&L for 75 mm thick cement concrete type D-2, 1:4:8 (40mm graded aggregate) as in sub base for floor finishes complete all as specified and as directed. |
| 117 | M&L for Machine cut Kota stone slab flooring 20-25mm thick over 15mm thick cement screed base laid in CM 1:3 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed. |
| 118 | M&L for Kota stone slab 20-25mm thick in riser of steps, skirting, dado, pillar laid over 10mm cement screed and jointed with including rubbing and polishing complete all as specified and as directed. |
| 119 | M&L for cement concrete 40 mm thick, type B-1, 1:2:4 (20mm graded aggregate) as in floor finishes and even and smooth without using extra cement complete all as specified and as directed. |
| 120 | M&L Hard drawn steel wire fabric dia 3.8 mm cut to lengths, bent to shape required and tying with and including mild steel wire (annealed) not less than 0.9mm in dia supplied and fixed in reinforcement complete all as specified and as directed. |
| 121 | M&L for mild steel plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, of Fe-410-W (Gde E-250) quality A without any attachment complete all as specified and as directed. |
| 122 | M&L for mild steel woks as in stairs (framed) including stringers, treads, landing, balusters, hand rails etc. including cleats, brackets, etc. of Fe-410-W (Gde E-250) quality A complete all as specified and as directed. |
| 123 | M&L applying two coats of synthetic enamel paint on new steel surfaces of any description over 10cm width or girth over a coat of red oxide primer including preparation of steel surfaces complete all as specified and as directed. |
| 124 | M&L applying two coats of synthetic enamel paint on new steel surfaces of any description not exc 10cm width or girth over a coat of red oxide primer including preparation of steel surfaces complete all as specified and as directed. |
| 125 | S & F mild steel works as in bands, straps, hold fasts and similar small articles conforming to Fe 290 Gde complete all as specified and as directed. |
| 126 | S&F MS press handles 100 mm size cast type, anodised complete all as specified and as directed. |
| 127 | M & L for 25mm thick 2nd class softwood boarding, planed one side, with butt joint fixed with nails in Fascia, eaves boarding complete all as specified and as directed. |
| 128 | M&L for mild steel work as in Framed work in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and as directed. |
| 129 | S&F 1.00 mm thick Mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as complete all as specified and as directed. |
| 130 | M&L for sand cushioning for protection of PVC cable with approved sand of uniform thickness, laid dry, by filling in trenches and punning to proper required cover complete all as specified and as directed. |
| 131 | Supply and laying of fly ash bricks of best quality laid flat equal to width of bricks, perpendicular to UG cable over the dry sand cushioning, for cable protection complete all as specified and as directed. |
| 132 | Supply and lay in trenches, fixed to wall/pole UG Cable XLPE insulated screened PVC beaded galvanised steel strip or wire armed heavy duty electric cable with multi stranded Aluminium conductor, 1100V grade of size 16 sqmm 4 core complete all as specified and as directed. |
| 133 | Supply, laying and testing cable XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 50 sq mm 3.5 core including taking down old unserviceable complete all as specified and directed. |
| 134 | M & L for point wiring with PVC insulated unsheathed single core multistranded copper conductor 1.5 sqmm, 1100 volts grade cable, FRLSH, drawn through PVC casing caping/ PVC Conduit of suitable size (as per site requirement) including accessories and provision of PVC boxes for mounting switches, switch socket, fan regulator, modular metal flush boxes (metal switch board of any type and size) with modular metal frame plate and white cover for housing switch required on site including one run of PVC insulated unsheathed multistranded copper conductor cable 1.5 sqmm (green colour) earth wire and connected to earth dolly for one light /one fan/one bell point controlled by one switch complete all as specified and as directed. |
| 135 | All as per item No 134 above but for one socket outlet 5 pins 5 amps controlled by one switch on same board. |
| 136 | All as per item No 134 above but for one socket outlet 5 pins 5 amps controlled by one switch on independent board. |
| 137 | All as per item No 134 above but for wiring with 2.5 sqmm copper wire (FRLSH) and 2.5 sqmm earth wire for socket outlet 6 pin 15 amps on independent board. |
| 138 | S&F Modular switch 1 way 6A, 1 module complete all as specified and directed. |
| 139 | S&F Modular Socket, 6A - 2/3 pin combined 2 module, complete all as specified and directed. |
| 140 | S&F Modular switch 1 way 16A, 1 module complete all as specified and directed. |
| 141 | S&F Modular Socket 6A/16A - 2/3 pin combined 2 module, complete all as specified and directed. |
| 142 | S&F Modular bell push 6 A, 1 Module, Complete all as specified and directed. |
| 143 | S & F Buzzer, Ding Dong Bell AC,230 Volts, Single pole complete all as specified and directed. |
| 144 | S&F lamp holder angle type PVC/Poly carbonate type insulated body with back plate suitable for batten/wall fitting complete all as specified and directed. |
| 145 | Supply and fix LED Bulb 9 Watt complete all as specified and directed. |
| 146 | S&F 20W surface / wall mounted batten LED luminaire, extruded aluminium housing with PC diffuser and ind electronic driver with high efficiency long life, CRI = 80 (Minimum), PF > 0.95, luminous efficacy > 100 lumens/Watt operating voltage 140V-240V, CCT (K) > 6500, THD < 10% complete including 20W LED tube rod with all accessories internally prewired and including connecting up with 3 core flexible copper conductor cable of suitable size from ceiling rose to connector of LED fitting prewired and including making connections with 3 core twisted flexible copper cable of size 23/.0076 from ceiling rose/PVC connector to light fittings complete all as specified and directed. |
| 147 | Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed. |
| 148 | S & F LED light fitting 1x9W/10W bulk head luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. |
| 149 | M & L for providing/ cutting the round/ square hole of required size in wall finishing the disturbed surfaces as per existing finishes and supply and fixing exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300m and connecting with and including PVC insulated three core 1.5 sqmm copper cable from ceiling rose to exhaust fan motor and writing MES No. with black synthetic enamel paint 2.0 cm high complete all as specified and directed. |
| 150 | Supply and fix water heater storage type, electric capacity 25 ltr along with all accessories BEE 5 star rated, complete all as specified and as directed. |
| 151 | Supply and fixing in replacement LED luminaire 600 mm x 600 mm, 36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and as directed. |
| 152 | S&F building security light fitting in repair LED 35 Watt for Energy saving and environmental friendly long life made up of pressure die cast aluminium housing with acrylic cover as diffuser with IP66 protection and Impact resistance of IK07 including driver unit and bracket made up of GI tube of suitable size (1.2 Mtr Length) etc complete all as specified and as directed. |
| 153 | M & L for sub main wiring with two single core 6 sqmm PVC insulated and unsheathed 1100 volts grade, stranded copper conductor (FRLSH) ISI marked drawn into & including medium grade PVC conduit/ casing caping 25 mm dia with all fittings and accessories and one continuous run of 6 sqmm copper conductor PVC insulated (green colour) as earth wire fixed into PVC casing / conduit (not less than 25mm outer dia) with all fittings and accessories fixed concealed/ surface including taking down old unserviceable submain wiring and making good disturbed surface complete all as specified and directed. |
| 154 | M & L for sub main wiring with two single core 4 sqmm PVC insulated and unsheathed 1100 volts grade, stranded copper conductor (FRLSH) ISI marked drawn into & including medium grade PVC conduit/ casing caping 25 mm dia with all fittings and accessories and one continuous run of 2.5 sqmm copper conductor PVC insulated (green colour) as earth wire fixed into PVC casing / conduit (not less than 25mm outer dia) with all fittings and accessories fixed concealed/ surface including taking down old unserviceable submain wiring and making good disturbed surface complete all as specified and directed. |
| 155 | S&F sheet metal enclosure for DBs (Double door type) when MCBs to be used single pole and neutral 8 way including blanking plate as required with 200 amps rated busbar 240V fixed sunk/flush to the wall or niche including taking down old unserviceable complete all as specified and directed. |
| 156 | S&F sheet metal enclosure for DBs (Double door type) when MCBs to be used single pole and neutral 4 way including blanking plate as required with 200 amps rated busbar 240V fixed sunk/flush to the wall or niche including taking down old unserviceable complete all as specified and directed. |
| 157 | MCB single pole & neutral 40 to 63 Amps 230 Volts 'C' series, 10 KA complete all as specified and directed. |
| 158 | S&F MCB's single pole 240 volts 6 to 32Amps 10 KA 'C' series, complete all as specified and directed. |
| 159 | S & F in repair distribution boards VTPN, 8way, double door 415 volts 50 Hz, AC including fixing on suitable rectangular block including taking down old unserviceable complete all as specified and directed. |
| 160 | S & F in repair MCCB ,100 Amp, 4 Pole breaking capacity 16KA, 415 Volt, 50 Hz with sheet metal enclosure complete all as specified and directed. |
| 161 | M&L for earthing complete with galvanized steel earth plate electrode 60cmx 60cmx6mm thick buried directly in ground (earth pit not less than 2.25m deep below normal ground level) with top edge of the plate not less than 1.5m below normal ground level, connected to galvanized iron wire 4.0mm dia by means of bolts, nuts and washers of galvanized iron or steel, protected by GI light grade pipe 15mm bore including GI light grade water pipe 20mm dia with funnel all as shown in electric plate No. 03 of 2009 SSR Pt-I and testing on complete including earth work in any type of soil, PCC 1:2:4 type B-0 as in earth pit and cover 40mm thick reinforced with XPM (weight not less than 4.0Kg/Sqm) and frame of angle iron 25x25x3mm with lugs 2 Nos and with 6mm dia MS bar handle made to shape, common salt, charcoal and testing on completion, all as specified and directed. |
| 162 | S&F switch piano flush button single pole, one way 5 amps complete all as specified and directed. |
| 163 | M & L for Switch socket combination 2 in 1, 3 pin, 6 Amps flush type completion, complete all as specified and directed. |
| 164 | Supply and fix Axis cabin wall mounting fan of size 400mm sweep complete and connecting up including provision of with copper standard conductors cables from ceiling rose/connector to fan. complete all as specified and directed. |
| 165 | M & L for ceiling rose, PVC/Polycarbonate three terminals complete all as specified and directed. |
| 166 | Supply and fixing LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed. |
| 167 | S&F LED bulb 5W suitable for fixing in PVC angle holder complete all as specified and directed. |
| 168 | S&F Deep Freezer hard top up to 320 litre capacity having single door complete all as specified and directed. |
| 169 | S&F Voltage stabilizer for automatic operation, single phase of capacity 1 KVA complete all as specified and directed. |
| 170 | Demolition of brick work or stone masonry built in cement mortar including all quoins, pillars, arches etc. but excluding ashlar facings, dressed stone work and precast concrete articles, complete all as specified and as directed. |
| 171 | Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 16, 2026
11:30 IST
Tender Published
Tender notice published.
Completed
Aug 22, 2026
18:00 IST
Corrigendum-1 Issued
Clarifications on tender conditions and amendments issued.
Completed
Aug 27, 2026
18:00 IST
Corrigendum-2 Issued
Clarifications on tender conditions and amendments issued.
Upcoming · 3 days
Aug 22, 2026
18:00 IST
Corrigendum-3 Issued
Clarifications on tender conditions and amendments issued.
CompletedAug 27, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 3 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender