Tender For Repair/ Maintenance Of Joinery, Plinth Protection, Att, Wall Panelling And Misc B/R Works Under Age B/R-I At Af Stn Palam Under Ge Af Palam, Delhi Cantt-10
Tender Value
25 Lakhs
Estimated cost
Bid Submission
14 Aug 2026
19 days left
EMD
50000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
New Delhi → Delhi
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repair/ Maintenance Of Joinery, Plinth Protection, Att, Wall Panelling And Misc B/R Works Under Age B/R-I At Af Stn Palam Under Ge Af Palam, Delhi Cantt-10
BOQ
| Sl. No. | Item Description |
| 1 | Taking down chowkats or frames with shutters area not exceeding 1.5 Sqm each (without taking off shutters from the frames) complete all as specified and as directed. |
| 2 | Taking down chowkats or frames with shutters area exceeding 1.5 Sqm but not exceeding 4 Sqm each (without taking off shutters from the frame) complete all as specified and as directed. |
| 3 | Taking down shutter of any discription area n. exc 1 Sqm each complete all as specified and as directed. |
| 4 | Taking down shutter of any discription area exc 1 Sqm and n exc 2 sqm each complete all as specified and as directed. |
| 5 | M&L for solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and as directed. |
| 6 | S&F for factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tube for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC `C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, Pa+nelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stliles and rails with suitable PVC sheet beading, and jointed together with solvent cement, supplying & fixing in the frame at site as per specification and drawing complete all as specified and as directed. |
| 7 | M&L for pressed steel frame for door with one rebated of size (105 x 60)mm with necessary fixing lugs, hinges, lock strike plate with and including back filling inside hollow section of chowkhat with PCC (1:2:4) tyype B0 (using 12.5mm graded stone aggregates) complete all as specified and as directed. |
| 8 | M&L for pressed steel frame for door with double rebated of size (125 x 60) mm with necessary fixing lugs, hinges, lock strike plate with and including back filling inside hollow section of chowkhat with PCC (1:2:4) tyype B0 (using 12.5mm graded stone aggregates) complete all as specified and as directed. |
| 9 | S&F 35mm thick factory made flush shutter, solid core construction with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed. |
| 10 | S&F for 35 mm thick 2nd class hard wood factory made glazed and skeleton shutters open rebated and prepared to receive glass or gauge etc divided into squares with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, provided with stiles and rails as specified in SSR Part-I Section-8 clause 8.20 (a) fixed to chowkats complete all as specified and as directed. |
| 11 | S&F stainless steel wire cloth, 0.36mm nominal dia of wire and and average width of aperture 1.40mm fixed with stainless steel wire staples complete all as specified and as directed. |
| 12 | S&F 5.50mm thick tinted sheet glass of selected quality fixed to aluminium frame work complete all as specified and as directed. |
| 13 | S&F for powder coated aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. with and including making good of the opening, such as plastering and painting jambs, levelling and finishing complete all as specified and as directed. |
| 14 | S&F powder coated aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc.complete all as specified and as directed. |
| 15 | S&F powder coated aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc.complete all as specified and as directed. |
| 16 | S&F aluminium powder coated three track sliding window with mosquito net two track for glass leaf sliding and one track for mesh leaf sliding outer frame weighing 0.699 Kg/m, (75x26) mm size equvalent Jindal model 20671, shutter plain of size (37.5x15)mm weighing 0.366 Kg/m, Section No 20690 Jindal), with powder coating of minimum thickness 50 micron with one or more rebates, sliding type without sash bars, 5mm thickness double tampered clear glass, rubber packing, snap beading screws, with horizontal sliding type with stainless steel mesh, frame, powder coated aluminium grill type AL 925 or equvalent grill, cutting in suitable size and fitting with screws and suitable beedings to aluminum window frame complete etc. with and including making good of the opening, such as plastering and painting jambs, levelling, neoprine packing alround and finishing complete all as specified and as directed. |
| 17 | S&F mild steel work in framed work such as grills, gratings, ladders etc., with ends of bars shouldered and/ or riveted, or forged into spikes, and similar work conforming to Fe 410 -0 or Fe 310 -0 complete all as specified and as directed. |
| 18 | S&F butt hinges 100mm extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21 complete all as specified and as directed. |
| 19 | S&F aluminium anodised barrel tower bolts of extruded section and fixed 150mm complete all as specified and as directed. |
| 20 | S&F aluminium anodised, barrel tower bolts of extruded section and fixed 125mm complete all as specified and as directed. |
| 21 | S & F cast type anodised aluminium handles of size 150 mm complete all as specified and as directed. |
| 22 | S&F 300mm long aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts of extruded sections or cast aluminium alloy and fixed with screws complete all as specified and as directed. |
| 23 | S&F in repair floor door stopper of size 140 mm long aluminium body and tongue, anodized with hard drawn steel spring including cleats etc fixed to door complete all as specified and as directed. |
| 24 | S&F in repair factory made 18 mm (+0.7 mm ) thick celuka PVC ply of density 600 kg/cbm manufactured by an ISO 900-2008 certified company, one side prelaminated and other side plain for kitchen cabinet/ cupboard shutter complete all as specified and as directed. |
| 25 | S&F in repair factory made 18 mm (+0.7 mm ) thick celuka PVC ply of density 600 kg/cbm manufactured by an ISO 900-2008 certified company plain for shelves/partions/drawers complete all as specified and as directed. |
| 26 | S&F 100 mm size stainless steel handle complete all as specified and as directed. |
| 27 | S&F 50 mm magnaetic catches with brass body and striking plate including letting in as fixed complete all as specified and as directed. |
| 28 | S&F 50 mm size stainless steel piano hinges complete all as specified and as directed. |
| 29 | S&F 40 mm stainless steel knobs complete all as specified and as directed. |
| 30 | S&F stailess steel telescope channel of size 500mm complete all as specified and as directed. |
| 31 | S&F stainless steel thali basket fo size (550 x 600x 200)mm Grade -304 complete all as specified and directed. |
| 32 | S&F stainless steel basket fo size (550 x 600x 200)mm Grade -304 complete all as specified and directed. |
| 33 | M&L for post constructional ATT (Anti-Termite Treatment) as per IS 6313 part-III amended upto date along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron, complete all as specified and as directed. |
| 34 | M&L for post constructional ATT (Anti-Termite Treatment) as per IS 6313 part-III amended upto date treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors, complete all as specified and as directed. |
| 35 | Taking down cement plaster on brick or concrete wall surfaces etc including raking out joints, hacking for keys, scrubbing down with water etc. complete all as specified and as directed. |
| 36 | Demolition of brick work or stone buillder built in cement mortar of any description complete all as specified and as directed. |
| 37 | M&L for brick work with sub class B works, straight or curved on plan exceeding 6m mean radius, built in cement mortar (1:6) complete complete all specified and as directed. |
| 38 | M&L for 10 mm thick rendering of Ready mix plaster of approved make on brick/ concrete surfaces as on ceiling, surface finished even and fair including water proofing compound by weight as per manufacturer's instructions, including necessary scaffolding up to (G+3 storey) complete all as specified and as directed. |
| 39 | M&L for 15 mm thick rendering of Ready mix plaster of approved make on brick/ concrete surfaces on external walls, fascia, parapet and chajjas finished the surfaces even and fair including water proofing compound by weight as per manufacturer's instructions, including necessary scaffolding up to (G+3 storey) complete all as specified and as directed. |
| 40 | M&L for preparing new plastered surfaces and applying two coats of oil bound distemper on wall surfaces including primer and 2mm thick cement base wall care putty complete all as specified and as directed. |
| 41 | M&L preparation of new plastered surfaces of wall surface and applying two coats of exterior emulsion paint (Apex of Asian or equivalent in Shalimar/Berger paints) over one coat of primer complete all as specified and directed by Engineer - in- charge. |
| 42 | M&L for preparation of new wooden or wood based surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified. |
| 43 | M & L for two coats of synthetic enamel paint over a coat of red oxide primer on new steel surface of any description over 10cm width including preparation complete all as specified and directed. |
| 44 | M&L for complete removal of old surface of walls by electrically operated grinder including necessary scaffolding up to (G+3 storey) etc and applying two coats of exterior emulsion paint over a coat of primer applied @ 0.90 litre/ 10 sqm over old surfaces and prepare the surface even and smooth complete all as specified and as directed by Engineer - in- charge. |
| 45 | M&L for preparation of plastered or unplastered old decorated surface of walls by brooming down or with steel wire brushing, scraping down, smoke soot's moulds, moss efflorescent salts& trading oil, greasy spots and filling cracks/holes with wall care putty /POP and applying two coats of oil bound distemper complete all as specified and directed by Engr-in charge |
| 46 | Material and labour for prepartion of plastered or unplastered old deorated surfces by brooming down or steel wire brushing scraping down smoke, soot, mould, moss, efforescent, salt & trading oil and grease spots and filling cracks/holes with wall care putty /POP and applying one coat of oil bound distemper on ceiling all as specified and directed by Engr in charge. |
| 47 | M&L for preparation of old painted surfaces of wood & wood based surfaces of any description not otherwise described over 10 cm width & girth and aplying one coat of synthetic enamel paint complete all as specified and directed by Engr-in charge. |
| 48 | Dismantling floor, hearth or wall tiling including cement mortar bedding and removing debries off the premises complete all as specified and directed by Engineer - in- charge. |
| 49 | M&L for glazed ceramic coloured tiles in vertical surface of size (450x 350)mm x 7mm thick /(350x250)mm x 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match with and including 10 mm thick rendering with CM (1: 4) as on vertical surfaces such as skirting, dados, etc complete all as specified and as directed. |
| 50 | M&L for non- skid ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM (1:6) complete all as specified and as directed. |
| 51 | M&L for non- skid ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM (1:6) complete all as specified and as directed. |
| 52 | M&L for non- skid ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in skirting, dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick screed bed in CM (1:4) complete all as specified and as directed. |
| 53 | M&L for vitrified tiles light shade 8 to 10 mm thick (square/ rectangular) polished, area of each tile exceeding 0.36 sqm as in floor etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM (1:6) complete all as specified and as directed. |
| 54 | Description all as per item no 53 above but as in vertical surface of wall, skirting over and including 10mm thick rendering of CM (1:4) complete all as specified and directed. |
| 55 | Demolition of cement concrete (un reinforced) in ground floors and pavings n. exc 15 cm thickness (below or above ground level) complete all as specified and as directed. |
| 56 | M&L for cement concrete (1:3:6) type C2 (using 40mm graded stone aggregate) as in plinth protection, 75 mm thick, surface finished even and smooth without using extra cement, with and including making joints 12 mm wide to the full depth of PCC at every 3 metres and at every change of direction and filling the same with & including bitumen 85/25 and sand in the proportion of (1:3 ) by weight complete all as specified and as directed. |
| 57 | S&F framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and as directed. |
| 58 | S&F 0.63mm thick mild steel, plain, black sheet in wall cladding, steel gates and covering to doors shutter and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required complete all as specified and as directed. |
| 59 | Dismantling wall panelling & ceiling board (fibre, pulp, insulation etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets, complete all as specified and as directed. |
| 60 | S&F solid PVC wall lining consisting of 5mm thick wood grain printed PVC sheet used instead of plain colour sheet and fixing at site including PVC sheet filletts of width 35mm thick for wall paneling inclusive of fixing on wall to make PVC frame as per specifications and drawing complete. |
| 61 | S&F in repair steel rolling shutters, 1.25 mm thickness of lath, with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete push/ pull or manual type complete all as specified and as directed. |
| 62 | Demolition of PCC of any discription and in any position not otherwise specifically provided for complete all as specified and as directed. |
| 63 | M&L for PCC (1:2:4) type B1 (using 20mm graded stone aggregate) as in kerbs or mud stops, rounded or chamfered edges, etc complete all as specified and as directed. |
| 64 | M&L for 75 mm thick PCC (1:4:8) type D-2 (using 40 mm graded crushed stone aggregate) as in sub base etc complete all as specified and as directed. |
| 65 | M&L for 60mm thick machine pressed with grey cement and pigment interlocking factory made paver blocks of any size and shape conforming to IS 15658-2006, M-35 set, jointed and pointed with and including 25 mm thick sand cushion complete all as specified and as directed. |
| 66 | M&L for glossy finish coloured chequered cement concrete tiles of size (30cm x 30cm) x 25mm thick, set jointed and pointed in neat cement slurry in floor with and including over 20mm thick screed bed in cement mortar (1:6) complete all as specified and as directed. |
| 67 | Taking up or down 15 mm bore steel water tubing and connections including cleaning for refixing or removal to store complete all as specified and as directed. |
| 68 | Taking up or down 20 mm bore steel water tubing and connections including cleaning for refixing or removal to store complete all as specified and as directed. |
| 69 | S&F tubes, 'medium grade' 15mm bore galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed. |
| 70 | S&F tubes, 'medium grade' 20mm bore galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed. |
| 71 | S&F in repairs 15 mm bore bib taps, chromium plated fancy type, long/ short body screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed. |
| 72 | S&F in repairs 15 mm bore two in one angle valve chromium plated with wall flange and fancy type with high pressure screwed down and with CP flange of same make complete all as specified and as directed. |
| 73 | S&F in repairs vitreous china wash down water closet pan (pedestal pattern), and trap white (excluding flushing cistern and seat cover) including connection to drain (or outgoing pipe) and to fushing pipe, antisyphonage pipe etc complete all as specified and as directed by Engineer-in-Charge. |
| 74 | S&F in repair PVC flushing cistern of 10 ltrs capacity valveless, syphonic action type, low level, white with inlet, ball valve, float and handle including brackets and PVC flush pipe of 32 mm bore and connection to pipes etc complete all as specified and directed by Engineer-in-Charge. |
| 75 | S&F in repairs 15mm bore angle cock, chromium plated screwed down, high pressure, with crutch or butterfly handles, screwed both ends for iron pipe or for unions and fixed all specified and as directed by Engr-in-Charge. |
| 76 | S&F in repair health faucet with double lock 1 meter brass plated stainless steel flexible hose and wall hook complete all as specified and as directed. |
| 77 | S&F in repair plastic water closet seat cover, white/black, closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device complete all as specified and as directed by Engineer-in-Charge |
| 78 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed. |
| 79 | S&F steel work in tubular/square/rectangular hollow section/angle iron, tee etc. for trusses/ purlins, rafter & sunshade including special shaped washer etc. complete using ERW or induction butt welded tubes using Fe as per IS 4923, Grade YST 310 including necessary machinery for upto 10m height structure complete in all respect as specified and directed. |
| 80 | Dismantling AC/CGI corrugated steel sheeting any gauge thickness including Nainital or similar pattern roof coverings complete all as specified and as directed by Engineer-in-charge. |
| 81 | S&F 0.50mm thick Pre-painted galvalume aluminium Zinc coating steel GI based corrugated sheet of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self taping screws complete all as specified and as directed. |
| 82 | Supply & fixing in repair door seal with rubber body embodied with necessary MS holder for fixing to bottom of the shutter complete all as specified and as directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 24, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 14, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 19 daysAug 21, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 26 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender