Tender For Special Repairs To Washrooms And Partition Walls In Dormitories Of 900 Men Block (P-195, P-196 & P-197) At installation Garuda Kochi
Tender Value
2.17 Crore
Estimated cost
Bid Submission
28 Aug 2026
3 days left
EMD
2.92 Lakhs
Bank guarantee accepted
Document Fee
2000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Ernakulam → Kerala
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Repairs To Washrooms And Partition Walls In Dormitories Of 900 Men Block (P-195, P-196 & P-197) At installation Garuda Kochi
Corrigendum
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 13-Aug-2026 | CGDM | BOQ | 21-Aug-2026 |
| 2 | 21-Aug-2026 | Bid Auto Extn Corrigendum | Bid Auto Extn Corrigendum | 28-Aug-2026 |
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed. |
| 2 | M& L for Pre-cast cement concrete block masonry with solid blocks, exc. 10 cm in width and setting in mortar 1:6, Type C1, 1:3:6 (using 20mm graded stone aggregate), complete all as specified and as directed. |
| 3 | M&L for Pre-cast cement concrete solid building blocks or slabs 10cm thick (with plain or interlocking joints as directed)setting in mortar 1:4, Type C1, 1:3:6 (using 20mm graded stone aggregate) as in walls complete all as specified and directed. |
| 4 | Demolition of cement concrete in ground floors and pavings in n exc 15cm thickness (below or above ground level) complete all as specified and directed. |
| 5 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed. |
| 6 | Taking down chowkhats or frames n exc 1.5 Sqm each with shutters (with out taking of shutters from the frames). complete all as specified and directed. |
| 7 | Taking down chowkats with shutters (without taking off shutters from the frame) exceeding 1.5 Sqm but not exceeding 4 Sqm. complete all as specified and directed. |
| 8 | Taking down cement plaster on brick or stone walls etc., including raking out joints, hacking for key, scrubbing down with water etc. complete all as specified and directed. |
| 9 | M& L for 10mmm thick cement plaster in CM 1:6 on fair surfaces of brick work or concrete surfaces of wall, finished even and smooth without using extra cement all as specified and directed. |
| 10 | M&L for rendering 8mm thick cement plaster in CM 1:4 with wpc @3% by weight finished even and smooth without using extra cement over 12mm thick back coat on brick or concret wall surfaces with cement mortar (1:6) complete all as specified and as directed. Note : WPC shall be meashured and paid seperately. |
| 11 | Supply only Liquid water proofing compound complete all as specified and directed. |
| 12 | M & L for 5 mm thick rendering in cement mortar 1:3 on fair faces of of ceiling surfaces finished even and smooth complete all as specified and as directed. |
| 13 | M& L for one coat of white wash on old ceiling surfaces including preparation of surfaces omplete all as specified and as directed. |
| 14 | M& L for three coat of white wash on new ceiling surfaces including preparation of surfaces complete all as specified and as directed. |
| 15 | M&L for complete removal of existing surfaces and applying two coats of oil bound distemper over a coat of primer over 1.5mm thick wall putty complete all as specified and directed. |
| 16 | M&L for preparation of new plastered surfaces and applying two coats of oil bound distemper over a coat of primer over 1.5mm thick wall putty complete all as specified and directed. |
| 17 | Complete removal of existing treatment of exterior surface including washing, rubbing down stopping of white wash, colour wash and cement base paint on wall surfaces complete all as specified and directed. |
| 18 | M&L for preparation for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over old surfaces. |
| 19 | M&L for preparation for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces. |
| 20 | M&L providing 100mm thick plain cement concrete 1:4:8, type D2 using 40mm graded stone aggregate as in floors to receive top layer complete all as specified and as directed. |
| 21 | Material and labour for non skid coloured ceramic tiles 7 to 8 mm thick square/ rectangular area of each tiles exceeding 0.18 Sqm but not exceeding 0.36 Sqm in floor etc, set and jointed epoxy tile joint filling using approved manufacturer on floor tiles over including provision of CM screed bed 10 mm thick in CM (1:4) all as specified and directed.Note : Epoxy tile joint filling shall be paid separately. |
| 22 | M&L for Glazed coloured ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including provision of backing coat 10 mm thick in CM (1:4) complete all as specified. |
| 23 | M&L 20mm thick Granite stone (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like fixed in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match over with shade of granite over 15mm thick screed bed in CM (1:4) complete all as specified and as directed. |
| 24 | M&L 20mm thick Granite (of any type) work (table rubbed and polished) for wall invertical surface12 mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shed of granite complete all as specified and as directed. |
| 25 | M&L for epoxy tile joint filling using Kerapoxy of MPAEI or equivalent on floor and walls and shall be applied as per the manufacturers instructions and as directed |
| 26 | S & F in repairs Vitreous China wash down water closet pan (EWC)(pedestal pattern) white colour , including supply only pedastal pan,seat cover, flush pipe and trap , connection to drain, PVC flushing cistern 10 ltr capacity and to flushing pipe , anti syphonage pipe etc, complete (excluding fixing bolts, complete all as specified and as directed. |
| 27 | S&F in repair Vitreous China Urinal, Half stall type, white (excluding flushing cistern, flush pipe and waste pipe) including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) |
| 28 | S&F in repair Vitreous china urinal partition white of size 310x700 mm in repairs complete all as specified and as directed. |
| 29 | S&F in repairs vitreous china ware under counter wash hand basin white, oval shape, size 550x400 mm size including cutting for and pinning ends of brackets or erecting stand fixed including 32mm waste fitting brass chromium plated complete all as specified and directed. Make :Jaquar FLS WHT 5701 or equivalent make in PS s approved by GE. |
| 30 | S&F in repairs PVC (SWR)multi floor trap with grating including jointing with solvent cement 75 mm dia of outlet complete all as specified and directed.. |
| 31 | S&F High density polyethylene (HDPE) pipes of pressure rating 6 Kgf/Sq.cm, 50 mm bore in repairs complete all as specified and directed. |
| 32 | S&F in repairs PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified |
| 33 | Supply and fix in repairs PTMT gratings with provision to receive the waste water pipe and fixed with white cement alround, 100 mm dia with minimum weight 25 gms complete all as specified and directed. |
| 34 | Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and as directed . |
| 35 | S&F PVC pipe single socketed in any length with rubber ring joints, laid in trenches/ floor or fixed to walls, 110mm bore complete all as specified and directed. |
| 36 | S&F PVC pipe single socketed in any length with rubber ring joints, laid in trenches/ floor or fixed to walls, 75 mm bore complete all as specified and directed. |
| 37 | S& F in reapairs PVC (SWR) bend any radius 110 mm bore with access door complete all as specified and directed. |
| 38 | S&F in repairs PVC (SWR) branch piece 100mm bore, double (double Y) equal or unequal with access door complete all as specified and directed. |
| 39 | S&F in repairs PVC (SWR) junction single, (Single T) 110 mm bore equal or unequal with access door complete all as specified and directed. |
| 40 | S& F in reapairs PVC (SWR) bend any radius 75 mm bore with access door complete all as specified and directed. |
| 41 | S&F in repairs PVC (SWR) branch piece 75mm bore, single (single Y) equal or unequal with access door complete all as specified and directed. |
| 42 | S&F in repairs PVC (SWR) junction single, (Single T) 75 mm bore equal or unequal with access door complete all as specified and directed. |
| 43 | Supply and fix in repair mirror of selected quality glass 600mmx450mm beveled edge, mounted on 6mm thick commercial ply wood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed. |
| 44 | Supply and fix in repairs pillar taps fancy type cast copper alloys, with capstan heads fancy type chromium plated screwed down high pressure with long screwed shanks and fly nuts screwed for iron pipe suitable for 15 mm bore pipe complete all as specified and as directed. |
| 45 | S&F for powder coated Anodised aluminium frame for doors, windows ventilators with one or more rebates including joining cleat for fixing etc. complete shall as specified. |
| 46 | S&F powder coated anodised aluminium window and ventilator shutter powder coated side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1no.) complete all as specified |
| 47 | S&F aluminium powder coated deco grill 75 mm aperture, made out of 7.5 mm plate and finished deco grill will have 7.5 mm width and 6 mm thick with rubber beading & looks etc complete all as specified and directed. |
| 48 | Supply and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminte shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame., complete as specified by the manufacturer and as per directions of Engineer-in-charge. |
| 49 | Supply and fixing to existing door frames 30 mm thick Glass Fibre Reinforced Plastic (FRP) panelled door shutter of required colour and approved brand and manufacture, made with fire - retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5 mm thick FRP laminate for panels conforming to IS: 14856, including fixing to frames, complete as specified by the manufacturer and as per directions of Engineer- in-charge. |
| 50 | Supply and fix stainless steel butt hinges medium weight size 100mm size complete all as specified and as directed |
| 51 | Supply and fix aluminium anodised barrel tower bolt extruded section of 150 mm long complete all as specified. |
| 52 | Supply and fix extruded aluminium alloy handles fabricated type anodised 150 mm size complete all as specified and directed. |
| 53 | Supply and fix 250mm long aluminium alloy anodised sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and as directed. |
| 54 | S&F 4.8mm thick frosted glass one side frosted ordinary quality and glazing with oil putty in square n exc 0.50 sqm in each plane complete all as specifed and as directed |
| 55 | S&F in repair of Aluminium anodised Tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified |
| 56 | S&F in repairs of Toilet paper holder, white vitreous China, box type fixed to walls with chromium plated (CP) brass screws complete all as specified and directed. |
| 57 | S&F in repairs of Towel Ring of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 90gms) complete all as specified and directed. |
| 58 | Removing demolished building material out side defence land of vehicles carring capacity 4.3to 10.2 tons to a distance exceeding 1.50 KM but not exceeding 2.0 KM beyond the lead included in the unit rates of demolition/dismantling items, including loading, unloading and stacking at the destination all as specified and as directed. |
| 59 | M&L for Plastering the surface with 10mm thick in CM 1:3 mixed with water proofing compound and providing a suitable length PVC (SWR) pipe 25mm dia spout with sufficient slope, applying a coat of oil bound bituminious primer on the surface @0.20 Kg/sqm, laying 4mm thick APP modified water proofing membrane of make BASF/IWL/STP Ltd/M/s Fosroc weighing not less than 4.0 Kg/sqm reinforced with non woven polyester mat weighing not less than 160 g/sqmhaving softening point not less than 140 degree centigrade longitudinal tensile strength not less than 800 N/5 cm, tearing strength of 180 N on the surface with 10 cm minimum overlap, sealing the joints of the membrane using LPG torch complete all as specified and directed Note: PVC Spout will be measured and paid seperately |
| 60 | S&F in repairs CPVC pipes 25mm dia spout pipes in any length to wall incl all necssary fittings such as bend,Tee, elbow reducer complete all as specified and directed Note : The portion of pipe inserted to the masonry / slab shall be fixed with water proofing bathseal tape of approved make two way to the entire width of masonry/slab, the rate quoted against this item is deemed to be inclusive of this provisions complete all as specified and directed. |
| 61 | Matrial and labour for plain cement concrete 1:4:8 type D2, using 40 mm graded stone aggregate as in fill up the sunken floor and testing of water tightness all as specified. |
| 62 | M&L removing cmpletely existing expansion joints (width of joint 20mm -25mm) between columns & walls and cleaning the surface & gap thouroughly with wire brush/coir brush & water jet and filling the gap with approved joint filling sealant, and inserthing 25mm thick neoprime/shalitex padsand sealed with poly sulphide sealent of approved make,minimum 40 mm deep 0.80mm thick/300mm wide wide aluminium sheet shall be fixed over the joint with rawl plugs & cadmium plated steel screws complete all as specified and directed. BASF/M/s fosroc/IWL/STP. |
| 63 | Dismantling wrought iron or mild steel work of any description not otherwise provided for all as specified. |
| 64 | Dismantling of wall and ceiling boards (fiber, pulp insulation etc.) or insulation boards / slabs / blankets, any thickness including fillet complete all as specified and directed. |
| 65 | S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasketetc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions. |
| 66 | M&L for 12mm thick prelaminated particle board, interior grade, prelaminated both side with decorative choice lamination & other side balancing white lamination, fixed with screws totimber frame work complete all as specified and directed. |
| 67 | Taking down old GI/CPVC pipe of size 40 mm complete all as specified and as directed. |
| 68 | Taking down old GI/CPVC pipe of size 25 mm complete all as specified and as directed. |
| 69 | Taking down old GI/CPVC pipe of size 20 mm complete all as specified and as directed. |
| 70 | Supply and fix on wall/concealed on wall high pressure CPVC pipes SDR-13.5 & plain CPVC SDR 11 fittings including all necessary fittings, solvents of size 40 mm dia complete all as specified and as directed. |
| 71 | All as per item No 70 here-in-before but of size 25 mm dia complete all as specified and as directed. |
| 72 | All as per item No 70 here-in-before but of size 20 mm dia complete all as specified and as directed. |
| 73 | S&F of Bib cock, CP Brass type quarter turn with flange and aerator, fancy type long body with wall flange cast copper alloy with crutch or butterfly handle screwed for GI/CPVC pipe of size 15 mm complete including taking down old tap complete all as specified and as directed by Engineer-in-Charge. Make : Cera Model F1014152 or Prayag/ Hindware as approved by GE. |
| 74 | S&F of Two way Bib cock, CP Brass type quarter turn with flange and aerator, fancy type with wall flange cast copper alloy with crutch or butterfly handle screwed for GI/CPVC pipe of size 15 mm complete including taking down old tap complete all as specified and as directed by Engineer-in-Charge. Make : Cera Model F1017163 or Prayag/ Hindware as approved by GE. |
| 75 | Supply and fixing of CP Brass type concealed stop cock regular body,Quarter turn with adjustable wall flange chromium plated with CP cup fancy type of size 20mm complete including taking down old tap complete all as specified and as directedby the Engineer-in-charge. Make Cera Cat Part No. F1015362 or Prayag/ Hindware as approved by GE. |
| 76 | S&F Stop cock, fancy type, chromium plated, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete including taking down old tap complete all as specified and as directedby the Engineer-in-charge. |
| 77 | S&F health faucet ABS body with wall hook and 1 metre SS braided rubber hose pipe, including taking out old complete including taking down old tap complete all as specified and as directed by Engineer-in-Charge. Make : Cera Model F8030108AB or Prayag/ Hindware as approved by GE. |
| 78 | Supply and fixing of swivel overhead shower (minimum weight 40 grams) of CP Brass type colour with shower arm (minimum weight 40 grams) 15mm size, 195 mm long with bend of 45 degree with flange for fixing with CPVC pipe including taking down old tap complete all as specified and as directed by the Engineer-in-charge.Make : Model No: F7020108AB of Cera or Prayag/ Hindware as approved by GE. |
| 79 | Taking down old PVC connection complete all as specified and as directed by Engineer-in-Charge. |
| 80 | S&F PVC connections 15mm size with PTMT nuts of length 300mm complete all as specified and as directed by Engineer-in-Charge. |
| 81 | Demolition of Concrete Roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work when and as required location complete all as specified and as directed. |
| 82 | Taking down old CPVC ball valve of size 40mm/ 20mm/ 25mm complete all as specified and directed. |
| 83 | S&F CPVC Ball Valve of size 40 mm dia suitable for CPVC pipe incl necessary fittings complete all as specified and as directed. Make : Supreme or equivalent make in the approved manufactures list. |
| 84 | All as per item No. 83 above but of size 25 mm dia complete all as specified and as directed. |
| 85 | Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. Removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. complete all as specified and as directed. |
| 86 | M&L point wiring with 1.5 Sqmm PVC insulated unsheathed FRLSH multistranded single core copper conductor cable in PVC concealed conduit rigid non metallic (ISI marked) fixed concealed on wall /roof except beam, column and RCC roof incl suitable for modular switch and socket (sunken box) modular white cover plate,flush metal box etc incl 1.5 Sqmm PVC insulated copper conductor as earth continuity wire for One light /Fan point controlled by one switch complete all as specified and as directed. |
| 87 | All as per item No 86.above but for one 5 pin 5 amps socket outlet on the same board complete all as specified and as directed. |
| 88 | All as per item No 86.above but for one 5 pin 5 amps socket outlet an independent board complete all as specified and as directed. |
| 89 | All as per item No 86 above but with 2.5 Sqmm copper conductor including 2.5 Sqmm copper cable on earth wire for one 6 Pin 16 Amps Socket outlet independent board complete all as specified and as directed. |
| 90 | S & F modular switch 1 way 6 Amps,1 module type complete all as specified and as directed. |
| 91 | S & F socket modular 6 Amps and 2/3 pin combined 2 module complete all as specified and as directed. |
| 92 | S & F switch 15 A One way SP modular type complete all as specified and as directed. |
| 93 | S & F Modular socket 6 A/16 A - 2/3 pin combined 2 module complete all as specified and as directed. |
| 94 | S&F ceiling rose surface bakelite 65 x 50mm 3 terminals complete all as specified and as directed. |
| 95 | S&F Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and as directed. |
| 96 | S&F Led bulb 12 Watt , min 100 lumen/watt LED Lamp WW/WH Type complete all as specified and as directed. Make : Havells/Crompton/Luker or equivalent make in the approved manufacturer list. |
| 97 | Supply and fixing LED tube light fittings 1x 20W, 230V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed. |
| 98 | Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers including necessary civil work for fitment of exhaust fan as per existing site conditions complete all as specified and as directed by engineer-in-chargeNote : Old exhaust fans to be deposited in MES store yard. |
| 99 | Taking down old DBs from existing position including MCB,s complete all as specified and as directed. |
| 100 | S & F in repair SPN enclosure with two pin and earth plug and socket complete with one SP MCB, 20 Amps having breaking capacity 10 kA, including taking down old unserviceable eath plug complete all as specified and as directed. |
| 101 | S&F Sheet metal enclosure SPN DB when MCB's to be used 8 way with 200 amps bus bar double door, complete all as specified and as directed. |
| 102 | Supply and fixing 240V, 10KA 'C' curve miniature circuit breaker (MCB) of SPN 32 AMP in the MCB DB complete with connection testing and commissioning. complete all as specified and as directed. |
| 103 | Supply and fixing 240V, 10KA 'C' curve miniature circuit breaker (MCB) of SP 6 To 32 AMP in the MCB DB complete with connection testing and commissioning. complete all as specified and as directed. |
| 104 | Taking down old sub main wiring of any size complete all as specified and as directed. |
| 105 | M&L for sub main wiring using proper colour coding 1100 Volts grade with 2 runs of 4 Sqmm (FRLSH) grade PVC insulated unsheathed multistranded copper conductor cable and 1 run of 4 Sqmm (FRLSH) cable as earth continuity wire drawn through and including PVC conduit medium grade not less than 25 mm dia with all conduit accessories concealed in wall/floor complete all as specified and as directed.Note - 2 runs of 4 Sqmm sub main wire and one run of 4 sq mm submain wire for earthing and PVC conduit pipe with accesories shall be measured as one unit. |
| 106 | M&L for sub main wiring using proper colour coding 1100 Volts grade with 2 runs of 6 Sqmm (FRLSH) grade PVC insulated unsheathed multistranded copper conductor cable and 1 run of 6 Sqmm (FRLSH) cable as earth continuity wire drawn through and including PVC conduit medium grade not less than 25 mm dia with all conduit accessories concealed in wall/floor complete all as specified and as directed.Note - 2 runs of 6 Sqmm sub main wire and one run of 6 sq mm submain wire for earthing and PVC conduit pipe with accesories shall be measured as one unit. |
| 107 | Note for item No 86 to 89, 105 & 106Civil work such as cutting chassis for fitment of conduit, making good the disturbed surface will be measured and paid separately. |
| 108 | M&L for Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm complete all as specified and as directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 21, 2026
11:30 IST
Tender Published
Tender notice published.
Completed
Aug 21, 2026
18:00 IST
Corrigendum-1 Issued
Clarifications on tender conditions and amendments issued.
Completed
Aug 28, 2026
18:00 IST
Corrigendum-2 Issued
Clarifications on tender conditions and amendments issued.
Upcoming · 3 daysAug 28, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 3 daysSep 04, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 10 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender