Tender For Comprehensive Repair And Maintenance Of Officers & Jco/Ors Md Accn Other Than Map Under Age B/R - Ii Of Ge (West) Mathura
Tender Value
45 Lakhs
Estimated cost
Bid Submission
14 Aug 2026
1 days left
EMD
90000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Mathura → Uttar Pradesh
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Comprehensive Repair And Maintenance Of Officers & Jco/Ors Md Accn Other Than Map Under Age B/R - Ii Of Ge (West) Mathura
BOQ
| Sl. No. | Item Description |
| 1 | Taking down cement plaster on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water etc. complete all as specified and directed. |
| 2 | Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc, laid, bedded, jointed and pointed in any mortar complete all as specified and directed by Engineer-in-charge. |
| 3 | Demolition of brick work or stone/boulders masonary, built in cement mortor including all quoins, arches pillars, etc but excluding ashlar facing dressed stone work and precast concrete articles complete all as specified and directed. |
| 4 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and removing rubbish off premises complete all as specified and directed. |
| 5 | Demolition of cement (un-reinforced) concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed by Engineer-in-Charge. |
| 6 | Demolition of cement concrete (un-reinforced) in ground floor and paving not exc 15 cm thickness (below or above ground level.) & removing unserviceable materials in low laying area, complete, all as directed by Engr-in-Charge. |
| 7 | Taking down chowkhats with shutter (without taking off shutters from the frame) area not exc. 1.50 Sqm each complete all as specified and directed. |
| 8 | Taking down chowkhats with shutter (without taking off shutters from the frame) area exc. 1.50 Sqm but n.exc 4.00 sqm each complete all as specified and directed. |
| 9 | Taking down shutters of any description exc 1 Sqm and not exc. 2 Sqm each complete all as specified and as directed by Engineer-in-charge. |
| 10 | Dismantling of wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed by Engineer-in-charge. |
| 11 | Dismantling AC sheet (Corrugated, Semi corrugated etc) as in roofs etc including ridges complete all as specified and directed by Engineer-in-charge. |
| 12 | Refixing door shutters of any description having area exc 1.00 sqm but not exc 2.00 sqm, each in the same opening including easing of door / window / cup board shutters for easy closing / opening incl tighening of hinges or changing the position of hinges adjustment of tower bolts, sliding bolts etc complete all as specified and directed by Engineer-in-charge.Note :- Labour for taking down of shutter included in this item, nothing shall be paid extra. |
| 13 | M&L for Brick work with fly ash bricks, straight or curved on plan exc 6m mean radius built in cement mortar (1:6) complete all as specified and directed by Engineer-in-charge. |
| 14 | M&L 35mm thick factory made glazed and skeleton shutters of 2nd class HW with partially panel shutter open rebated and prepared to receive glass / gauze etc edges or framing plain chamfered or rounded fitted with cut or mitred beads for securing glass etc as specified in SSR Part-1 section 8.24 (a) complete all as specified and directed. |
| 15 | S&F for 30mm thick flush shutter solid core construction with block board core & ply wood face panels, commercial type on both faces complete all as specified and directed by Engineer-in-charge. |
| 16 | S&F factory made solid PVC door frame of size 50mm x 47mm made out of 5mm thick plain colour PVC sheet reinforced with MS square tube complete all as specified & shown in relevant drawing of item No. 08095 in MES Schedule (Part-II) and directed by Engineer-in-Charge. |
| 17 | S&F 30mm thick factory made solid core PVC door shutter (style) consisting of frame made out of mild steel tubes for top and bottom rails, mild steel frame shall be covered with heat moulded plain colour PVC sheet, 'C' channel having PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail and bottom rail; panelling of plain colour PVC sheet to be fitted in mild steel frame welded/ sealed to the styles and rails with suitable PVC sheet beading and joined together with solvent cement, complete, all as specified & shown in relevant drawing of item No. 08080 in MES Schedule (Part-II) and directed by Engineer-in-Charge. |
| 18 | S&F 150 mm long aluminium anodized barrel tower bolts of extruded section (ISI marked) complete all as specified and directed by Engineer-in-charge. |
| 19 | S&F Aluminium handle cast type anodized 150mm long complete all as specified and directed by Eng-in-charge. |
| 20 | S&F 100mm long stainless steel Butt hinges fixed complete all as specified and directed. |
| 21 | S&F 125 mm aluminium anodised Hasp and staple, safety type with mild steel hinge pin including bolt to hinge plate (ISI marked) complete all as specified and directed by Engineer-in-charge. |
| 22 | S&F 100mm size mild steel butt hinges cold rolled medium weight (ISI marked) complete all as specified & directed by Engineer-in-Charge. |
| 23 | S&F 300mm mild steel (Helical door spring) ordinary rat tail rod pattrern spring including roller and roller plate complete with necessary welding work complete all as specified and directed. |
| 24 | S&F 300mm long aluminium alloy anodised sliding door bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy (ISI marked) complete all as specified & directed by Engineer-in-Charge. |
| 25 | S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or stainless steel wire staples complete all as specified and directed by Engineer-in-Charge. |
| 26 | S&F in repairs stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or stainless steel wire staples complete all as specified and directed by Engineer-in-Charge. |
| 27 | Hacking out old broken glass any thickness, size, quality or description from wooden / metal frame and punching or drilling out old glazing pins/spring clips complete all as specified and directed by Engineer-in-charge. |
| 28 | M&L 3mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing/new surfaces, complete all as specified and as directed. |
| 29 | M&L 3mm thick figured glass pin head type and glazing with oil putty in square not exc 0.5 sqm in each pane complete all as specified and directed by Engineer-in-charge. |
| 30 | M&L for 25mm thick PCC (1:2:4) type B-0 using 12.5mm graded stone aggregate ) as in floor finishes and leveling course complete all as specified and directed. |
| 31 | M&L for glazed ceramic tiles (coloured) 450mm x 300mm x 7mm thick on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick rendering in cement & sand mortar (1:4) including necesary cutting as per site requirment complete all as specified and directed by Engineer-in-charge. |
| 32 | M&L Non skid coloured ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.06 sqm but n.exc 0.11 sqm in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match with and including 15mm thick screed bed in cement mortar (1:6) for laying floor finishes complete all as specified and as directed. |
| 33 | M&L Non skid coloured ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.18 sqm but n.exc 0.38 sqm in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match with and including 15mm thick screed bed in cement mortar (1:6) for laying floor finishes complete all as specified and as directed. |
| 34 | M&L for vitrified ceramic tiles light shade 8-9mm thick (square/ rectangular) polished area of each tile not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick cement screed bed in CM (1:4) complete all as specified and directed. |
| 35 | All as per item No 34.00 (here-in-before) above but as in skirting over 10mm thick backing coat in CM (1:3) complete all as specified and directed. |
| 36 | M&L for machine cut Kota stone slab flooring 18 to 20mm thick (minimum size 550mm x 550mm or size as directed) laid over & including screed bed or bedding layer of 20mm thick in CM (1:6) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed by Engineer-in-charge. |
| 37 | M&L for machine cut Kota stone slab 18 to 20mm thick (minimum size 550mm x 100mm or size as directed), on vertical surfaces such as dado, skirting, raiser of steps etc. laid over & including rendering 10mm thick in CM (1:4) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including cutting, grinding, rubbing and polishing complete all as specified and directed by Engineer-in-charge. |
| 38 | M&L for 18-20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like including 20mm screed bedding in cement mortar (1:4) and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed. |
| 39 | M&L Green marble of work 16-18mm thick (table rubbed and polished) in cooking platform and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigments to match with marble shade including screed bed or bedding layer of 20mm thick in cement mortar (1:6) complete all as specified and as directed. |
| 40 | M&L 75 mm thick Cement concrete type D-2, (1:4:8) using 40 mm graded stone aggregate as in sub base complete all as specified and directed. |
| 41 | M&L for Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed by Engineer-in-Charge. |
| 42 | Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar (1:3) including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete all as specified and directed. |
| 43 | M&L for rendering 5mm thick in CM (1:4) as on ceiling complete all as specified and directed. |
| 44 | M&L rendering 15 mm thick in CM 1:6 on brick masonry surfaces or on other than fair faces of brick masonry finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge. |
| 45 | M&L for rendering 15mm thick in CM (1:4) on fair faces of brick or concrete surfaces, finished surface even & fair without using extra cement complete all as specified and directed. |
| 46 | M&L for 75 mm thick PCC (1:3:6) type C-2 using 40 mm graded crushed stone aggregate as in plinth protection, finished fair and even complete all as specified and directed by Engineer-in-charge.Note :- Plinth protection shall be laid to slope (1 in 30) in bays not exceeding 3 metre in length and joints of 6 mm wide and 10 mm deep shall be provided along the wall and bays and same shall be filled with sealing compound grade B. Cost of ceiling compund is included in the unit rate of this item complete all as spcified and directed. |
| 47 | Taking up or down 15mm dia, steel tubing & connections including cleaning for refixing or removal to store complete all as specified and directed by Engineer-in-Charge. |
| 48 | Taking up or down 20mm dia, steel tubing & connections including cleaning for refixing or removal to store complete all as specified and directed by Engineer-in-Charge. |
| 49 | S&F 15 mm dia steel water tubing, galvanized, medium grade, with all fittings, fixed to walls and ceiling or in floor complete all as specified and directed by Engineer-in-Charge |
| 50 | S&F 20 mm dia steel water tubing, galvanized, medium grade, with all fittings, fixed to walls and ceiling or in floor complete all as specified and directed by Engineer-in-Charge |
| 51 | Fixing only 15mm bore old galvanised steel water tubing including cleaning with & including new fittings and fixed complete to walls and ceilings or laid in floors in new or old position complete all as specified and directed by Engineer-in-charge.Note: GI tubing retrieved vide item No 49.00 shall be used under this item. |
| 52 | Fixing only 20mm bore old galvanised steel water tubing including cleaning with & including new fittings and fixed complete to walls and ceilings or laid in floors in new or old position complete all as specified and directed by Engineer-in-charge.Note: GI tubing retrieved vide item No 50.00 shall be used under this item. |
| 53 | M&L for treatment of sunken floor slab comprising of the following specifications with and including demolition of sunken floors complete all as specified and directed:-(i) Cleaning the sunken/lowered portion of \ RCC slab surface (incl vertical total depth plus skirting height) of floors by wire brush,chisel out any mortar sticking to the surface and brooming completely. Provn of 40 mm thick avg PCC 1:2:4 type B-O using 12.5mm graded aggregate as in padding concrete to achieve proper slope incl cutting holes in bricks or RCC wall for sprout.(ii) Rendering of uneven surfaces with 6mm thick CM 1:4 mixed with and incl integral water proofing compound Sika Plastocreat plus or equivalent make in Fosroc / Thermax as approved by GE @ 0.2% by wt of cement consumed incl filling it with water to check dampness and seepage and where dampness/seepage is noticed, nozzles shall be fixed and grouting carried out.Cont/- |
| 54 | Cont/-(iii) All junctions points of side wall where CI/GI/PVC pipes are passing through shall besealed with epoxy puttySikaguard 694 F(I) or equivalent make in Fosroc/Thermax as approved by GE(iv) After drying putty, wash the slab and sides of sunken portion with water and make it clear and clean(v) Applying two coats of polymer modified cementious water proof coating with Sika Topseal 107 or equivalent make in Fosroc/Thremax as approved by GE over base coat as per manufacturer's instruction to bottom and vertical sides upto finished floor level +100 mm height. The thickness of two layers shall be 1mm. When the second layer is still sticky, coarse sand spray shall be carried for the vetical and bottom surface of the sunken portion.Cont/- |
| 55 | Cont/-(vi) Plaster the bottom surface and sides up to bottom of the skirting with minimum 20mm thick CM 1:4 mixed with and incl integral water proofing compound Sika Plastocreat plus or equivalent make in Fosroc/Thermax as approved by GE @ 0.2% by wt of cement consumed as per manufacturer's specification incl rounding of corners and injuctions sloping towards spout.(vii) All pipes laid in sunken portion shall be covered with 50mm thick PCC 1:3:6 all round after painting with anticorrosive paint. |
| 56 | S &F for rotational moulded polythelene water tanks triple layer white colour (cylindrical vertical with closed top) hoisted and fixed in position for 500 ltr. storage capacity including disconnecting and taking down old unserviceable tanks and ball valve complete all as specified and directed. |
| 57 | S &F for rotational moulded polythelene water tanks triple layer white colour (cylindrical vertical with closed top) hoisted and fixed in position for 750 ltr. storage capacity including disconnecting and taking down old unserviceable tanks and ball valve complete all as specified and directed. |
| 58 | S&F PTMT ball valve, high pressure, with polythene float and flynut complete, screwed for iron pipe 20mm bore or brass ferrule and fixed complete all as specified and directed by Engineer-in-Charge. |
| 59 | S&F in repairs PTMT ball valve, high pressure, with polythene float and flynut complete, screwed for iron pipe 20mm bore or brass ferrule and fixed complete all as specified and directed by Engineer-in-Charge. |
| 60 | Cleaning and removing all scale and dirt, etc. from PVC/RCC tanks Exc 250 but not exc 500 ltr capacity and form mouths of circulating pipes, complete all as specified and directed by Engineer-in-Charge. |
| 61 | Cleaning and removing all scale and dirt, etc. from PVC/RCC tanks Exc 500 but not exc 1000 ltr capacity and form mouths of circulating pipes, complete all as specified and directed by Engineer-in-Charge. |
| 62 | S&F PVC (SWR) 110 mm bore pipes single socketed in any length with rubber ring joints laid in trenches or fixed to wall complete including taking down old unserviceable PVC pipe with fittings complete all as specified and directed. |
| 63 | S&F PVC (SWR) 75 mm bore pipes single socketed in any length with rubber ring joints laid in trenches or fixed to wall complete including taking down old unserviceable PVC pipe with fittings complete all as specified and directed. |
| 64 | S&F PVC (SWR) 110mm bore bends any radius complete all as specified and directed. |
| 65 | S&F PVC (SWR) 110mm bore junction single, (Single T) equal or unequal complete all as specified and directed. |
| 66 | S&F PVC (SWR) 75mm bore bends any radius complete all as specified and directed. |
| 67 | S&F PVC (SWR) 75mm bore junction single, (Single T) equal or unequal complete all as specified and directed. |
| 68 | S&F in repairs 32mm bore CP waste coupling fittings for sinks, basins with long shanks and fly nuts, flange and bedded in red cement and fixed complete all as specified and directed by Eng-in-charge. |
| 69 | S&F in repair 32mm dia waste coupling of PTMT (half or full threaded) Minimum weight 32mm-45gms/40mm-60 gms) Ditto but suitable for urinals (Minimum weight 32mm-45gms) |
| 70 | S&F in repair chromium plated shower rose with shower arm or without swivel joints including fixing to steel pipe of 100 mm size complete all as specified and directed by Eng-in-charge. |
| 71 | S&F in repair CP Jet spray butter fly design fixed on EWC with stanless screw as approve complete all as specified and directed by Eng-in-charge. |
| 72 | S&F in repairs Toilet paper holder with flat recessed type stainless steel complete all as specified and directed by Engineer-in-Charge. |
| 73 | S&F in repair 450mm long PVC connection suitable for 15 mm bore with PTMT nuts on both sides complete all as specified and directed by Engineer-in-charge. |
| 74 | S&F in repairs PVC flexible waste down pipe-32 mm dia and 1150 mm long with PVC waste coupler complete all as specified and directed. |
| 75 | S&F in repair 15mm bore CP angle valve, fancy type, cast copper alloy, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and directed by Engineer-in-charge. |
| 76 | S&F in repair 15mm dia stop cock cast copper alloy, fancy type with, chromium plated long shank and cup (concealed type) with crutch or butterfly handle screwed down high pressure, screwed both ends for iron pipe complete all as specified & directed by Engineer-in-charge. |
| 77 | S&F in repair 20mm bore stop valve cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union complete all as specified and directed. |
| 78 | S&F in repair wall mixer CP brass cromium plated hot and cold with or without telephonic shower arrangement 15 mm bore as specified. |
| 79 | S & F in repair for 15mm bib tap standard of PTMT any colour screwed for iron pipe and fixed complete all as specified and directed by Eng-in-charge. |
| 80 | S&F in repair 15 mm bore bib tap, cast copper alloy, chromium plated, long body, fancy type screwed down and screwed for iron pipe or for brass ferrule complete all as specified and directed by Engineer-in-charge. |
| 81 | S&F in repair vitreous china squatting pan Orissa pattern, white of size 580x440mm with integral foot rests (excluding flushing cistern and flush pipe) including cast iron 'P' or 'S' trap, PCC filling and connection to trap and flushing pipe, antisyphonage pipe etc complete all as specified and directed by Engineer-in-charge. |
| 82 | S&F in repairs vitreous china wash down water closet pan (Pedestal pattern), white including connection to drain (or outgoing pipe) and to flushing pipe, anti-sypohonage pipe etc. & with plastic WC seat cover white closed pattern with flat bottom and cover and mild steel chromium plated or aluminized hinging device and jet spray complete all as specified & as directed by Engineer-in-charge. |
| 83 | S&F in repairs PVC EWC seat cover of any type, white colour for pedestal pan complete all as specified and directed by Eng-in-charge. |
| 84 | S&F in repair 10 litre capacity PVC valveless symphonic action type low level flushing cistern (ISI marked) including 32 mm dia PVC flush pipe connected to water closet with inlet, ball valve, float and handle complete all as specified and directed by Engineer-in-charge. |
| 85 | S&F in repairs, vitreous China wash hand basin, white, flat back size 550 x 400mm including 15mm dia, 450 mm long HDPE PVC connection, 750 mm long 32mm bore HDPE waste down pipe including CI brackets complete all as specified and directed. |
| 86 | S&F pillar taps (fancy type), of 15 mm dia, cast copper alloy, with capstan heads, with chromium plated, screwed down high pressure with or without lettered 'hot' or cold with long screwed shanks and fly nuts, screwed for iron pipe and fixed. |
| 87 | S&F in repair pillar taps (fancy type), of 15 mm dia, cast copper alloy, with capstan heads, with chromium plated, screwed down high pressure with or without lettered 'hot' or cold with long screwed shanks and fly nuts, screwed for iron pipe and fixed. |
| 88 | M&L preparation new or previously untreated steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over and including one coat of red oxide zinc chrome primer complete all as specified and directed by Engineer-in-Charge. |
| 89 | M&L for preparation of steel surface already treated with primer over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge. |
| 90 | M&L for preparation of new wooden or wood based surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed by Engineer-in-Charge. |
| 91 | M&L for preparation of old steel surfaces of any description or girth over 10 cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed. |
| 92 | M&L for preparation of old painted wooden surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed. |
| 93 | S&F factory made steel window / ventilators conforming to IS-1038 with side hung shutters including projected type hinges with 2 Nos MS 100 mm size tower bolt over MS flat iron for each openable leaf & Z section handle and steel peg stay complete without glazing bars, dovetailed or welded including one shop coat of red oxide zinc chromate primer complete all as specified & directed by Engineer-in-Charge. |
| 94 | S&F factory made steel window conforming to IS-1038 with side hung shutters including projected type hinges with 2 Nos MS 100 mm size tower bolt over MS flat iron for each openable leaf & Z section handle and steel peg stay complete with glazing bars, dovetailed or welded including one shop coat of red oxide zinc chromate primer complete all as specified & directed by Engineer-in-Charge. |
| 95 | S&F factory made steel ventilator with top hung shutter including hinges, steel peg stay, handle including one shop coat of Zinc Chromate primer complete all as specified and directed by Engineer-in-charge. |
| 96 | S&F framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and directed. |
| 97 | S&F mild steel framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, cooler stand 12mm sq guard bar, framework of water tanks and similar works of quality Fe 290 (Gde E-165) etc complete all as specified and directed by Engineer-in-charge. |
| 98 | M&L for preparing newly plastered surfaces and applying applying two coats of distemper with distemper oil emulsion white or tinted over and including one coat of 1mm thick wall care putty complete all as specified and directed. |
| 99 | M&L for preparation of old distempered surfaces of walls and applying one coats of oil bound distemper white or tinted, complete all as specified and directed by Engr-in-Charge. |
| 100 | M&L for preparation of new plastered surface of wall and applying three coats of white wash complete all as specified and directed. |
| 101 | M&L for preparation of new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed. |
| 102 | M&L for preparation of old decorated, plastered or pointed surfaces of ceiling by brooming down or steel wire brushing, scrapping down smoke soot moulds, moss and efflorescent, salts and treating oil & greasy spots etc and applying one coat of white wash complete all as specified & directed by Engineer-in-Charge. |
| 103 | M&L for preparartion of new plastered surfaces of walls and applying two coats cement base paint on walls upto G+2 story bldg complete all as specified and directed. |
| 104 | M&L for preparation of old plaster surfaces of walls and applying one coat of cement based paint on walls for height upto G+2 story bldg complete all as specified and directed. |
| 105 | M&L for 25mm thick (measured solid) precast cement concrete (1:2:4) type B0 using 12.5mm graded stone aggregate) louvers and jallies, including all mouldings but excluding frame, set in CM (1:4) complete all as specified and directed by Engineer-in-Charge. |
| 106 | M&L for Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) FE-290 GD-165 including distance pieces, cleats etc. Complete all as specified & directed. |
| 107 | M & L for Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws complete all as specified and directed by Engineer-in-charge. |
| 108 | S&F Pre-painted galvalume aluminium zinc coating GI based plain steel ridges suitable for corrugated steel sheet 0.5mm thick of red colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 109 | M&L for PCC (1:4:8) type D-2, using 40mm graded stone aggregate in foundation, filing and mass concrete complete all as specified and directed. |
| 110 | S&F in repairs curtain rod, stainless steel of 25mm dia with fixing brackets stop rollers etc fix complete all as specified and directed. |
| 111 | S&F in repair CP Health faucet with stand fixed on wall in CP hose pipe 1 mtr length and stainless steel screw as approve complete all as specified and directed by Eng-in-charge. |
| 112 | S&F in repair brass chromium plated tubular towel rail 20mm dia; 'D' type, 600mm long between flanges fixed to plug with chromium plated brass screws including wooden or plastic cleat complete all as specified and directed by Engineer-in-Charge. |
| 113 | S&F in repair 600mm x 450mm beveled edge looking mirror of selected quality glass not less than 5.5mm thick, mounted on 6mm thick commercial plywood including PVC moulded framing and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed by Engineer-in-charge. |
| 114 | S&F in repairs Bevelled edge mirror of 5.5mm to 6mm thick selected quality glass flaw less, firmly and fixed with screw cap decorative cover polished mirror stainless steel cover full round mirror holder bracked of 6mm size of appropriate quantity as per requirement complete all as specified and directed |
| 115 | S&F in repair PVC Syphon kit assembly in existing flush tank complete all as specified and directed. |
| 116 | S&F in repair PVC mirror cabinet size 350X450mm of standard size fixed to wall with PVC sleeves and steel screws complete all as specified and directed. |
| 117 | S&F in repairs Sheet glass shelf assembly consisting of 5.5mm thick sheeet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed. |
| 118 | S&F in replacement 18mm thick PVC Celuka Ply plain white colour both side fixed with screws solvent cement/adhesive to make kitchen cabinet sides top and bottom and shelves inside the cabinets complete as per specifications and as directed by the Engineer-in-Charge (Density - 575 to 600 Kg/CBM) |
| 119 | S&F in replacement 18 MM thick PVC Celuka board of single side prelam/rigidlam color fixed with screws, solvent cement/adhesive to make kitchen cabinet sides top and bottom and shelves inside the cabinet, cupboard shutters/frames, (Density- 575 to 600 Kg/ CBM), complete, all as directed by Engineer-in-Charge. |
| 120 | S&F auto closing hinges 35mm of 0 crank (KH-001) or 8 crank (KH-002) openable at 110 degree for kitchen cabinet shutters complete all as specified and directed. |
| 121 | S&F Magnetic catcher fixed in with nut,screw washer complete all as specified and directed by Eng-in Charge. |
| 122 | S&F in repair PVC (SWR) floor trap 75mm dia outlet plain with grating including jointing with solvent cement including jointing to waste pipe fixed in cement concrete 1:2:4, type B-1 complete all as specified and directed. |
| 123 | S&F in repair stainless steel grating 100mm bore size fixed with white cement complete all as specified and directed by Eng-in-charge. |
| 124 | S&F in repairs CP Soap dish, embedded in the wall approximate size 160x160x90mm complete all as specified and directed. |
| 125 | S&F in repair sink with drainage board made of stainless steel 1mm thick for kitchen with plugs, washers and wastes, overall size 915mm x 460 mm / (36\\" x 18\\") bowl size 410mm x 355mm / (16\\" x 14\\") and depth 175mm / (7\\") including waste pipe of polythelene of low or high density or PVC 32mm dia & waste fitting brass chromium plated 32mm bore with long screwed shanks and fly nuts including making holes in brick walls for brackets and fixed in CM (1:3) or PCC 1:2:4 type B0 complete all as specified and directed by Engineer-in-charge.Make :- Nirali model Elegance (Glossy) / Prayag model No 1128-D Gold Series (Gloss) / Silver Shine (Bluestar sanitary industries Pvt Ltd) model No SSSB-52 (Glossy) or equivalent in makes mentioned in Appendix 'A' here-in-after.Note :- Size of sink for different mafufacturer may slightly varried from size mentioned in description of item. Contractor has to provide sink as per cat No mentioned against make of sink. where cat No is not mentioned against any make, in that case sink of size mentioned in description has to provide, if exact size of sink is not available, then next higher size sink has to be provided. Nothing extra shall be paid on this account. |
| 126 | S&F in repair of HDPE PVC lid tank cover with thread typ for any capacity all as specified and directed. |
| 127 | S&F in repair stainless steel plate rack of size 900mm x 900mm x 254mm made out of 0.80mm thick stainless steel of first quality complete all as specified and directed by Engineer-in-Charge.Make :- Nirali model Elegance (Glossy) / Prayag Gold Series (Gloss) / Silver Shine (Bluestar sanitary industries Pvt Ltd). |
| 128 | Taking down surface / concealed copper / aluminium point wiring (light, bell, fan, socket or power) complete, including fixtures and fittings such as switches, ceiling roses, lamp holders, pendants, sockets, regulators, tubelight fittings etc and making good disturbed surfaces with plaster on walls, floors etc complete all as specified and directed. |
| 129 | M&L for Point wiring complete with 1.5 sqmm single core FRLSH PVC insulated cable with multi stranded copper condutor in and including PVC conduit 20mm dia and thickness not less than 1.5mm, ISI marked with all accessories for surface or concealed conduit as directed at site incl chase cutting for one light/fan point controlled by one one way switch including MS sheet sunken box concealed on wall duly painted inside and outside with one coat of red oxide primer and two coats of black bituminous paint with 3mm thick hylum brand bakelite sheet cover for fixing switches, sockets, regulators etc. alongwith 1.5 sqmm multi stranded FRLSH, PVC insulaedcopper cable as continuous earth connected to common earth and earth dolly including making good the disturbed surfaces complete all as specified and as directed. |
| 130 | All as per Sl item No 127.00 above here-in-before for light point controlled by two way switch complete all as specified and directed. |
| 131 | All as per Sl item No 127.00 above herein before but for one bell point controlled by one bell push. |
| 132 | All as per serial item No. 127.00 here-in-before but for One 3 pin 5 Amp socket outlet on independent board. |
| 133 | All as per serial item No. 127.00 here-in-before but for One 5 pin 5 Amp socket outlet on the same board with other switches. |
| 134 | All as per item No 127.00 (here-in-before) but for one 6 pin socket outlet 16amps point controlled by one switch on independent board. |
| 135 | M&L for Point wiring complete with 2.5 sqmm single core FRLSH PVC insulated cable with multi stranded copper condutor in and including PVC conduit 20mm dia and thickness not less than 2.5mm, ISI marked with all accessories for surface or concealed conduit as directed at site incl chase cutting for one light/fan point controlled by one one way switch including MS sheet sunken box concealed on wall duly painted inside and outside with one coat of red oxide primer and two coats of black bituminous paint with 3mm thick hylum brand bakelite sheet cover for fixing switches, sockets, regulators etc. alongwith 1.5 sqmm multi stranded FRLSH, PVC insulaedcopper cable as continuous earth connected to common earth and earth dolly including making good the disturbed surfaces complete all as specified and as directed. |
| 136 | All as per Sl item No 133.00 above here-in-before for light point controlled by two way switch complete all as specified and directed. |
| 137 | All as per Sl item No 133.00 above herein before but for one bell point controlled by one bell push. |
| 138 | All as per serial item No. 133.00 here-in-before but for One 3 pin 5 Amp socket outlet on independent board. |
| 139 | All as per serial item No. 133.00 here-in-before but for One 5 pin 5 Amp socket outlet on the same board with other switches. |
| 140 | M&L for Sub main wiring with 2 runs of 4 sqmm single core PVC insulated but unsheathed multistranded copper conductor FRLSH 1100 volts grade cable drawn through and in existing surface / recessed PVC conduit and connecting incoming/outgoing electric connections and one run of 4 Sqmm single core PVC insulated but unsheathed multistranded copper conductor FRLSH 1100 volts grade cable as earth conductor including taking down old unserviceable submain wiring and making good disturbed surfaces complete all as specified and directed. Note : Two runs of 4 Sqmm cable, one run of 4 Sqmm earth conductor and one run of PVC conduit of 25mm dia shall be measured and paid as one unit length. |
| 141 | M&L for Sub main wiring with 2 runs of 6 sqmm single core PVC insulated but unsheathed multistranded copper conductor FRLS 1100 volts grade cable drawn through and in existing surface / recessed PVC conduit and connecting incoming/outgoing electric connections and one run of 6 Sqmm single core PVC insulated but unsheathed multistranded copper conductor FRLS 1100 volts grade cable as earth conductor including taking down old unserviceable submain wiring and making good the disturbed surfaces complete all as specified and directed. Note: Two runs of 6 Sqmm cable, one run of 6 Sqmm earth conductor and one run of PVC conduit of 32mm dia shall be measured and paid as one unit length. |
| 142 | M&L for Sub main wiring with 2 runs of 10 sqmm single core PVC insulated but unsheathed multistranded copper conductor FRLS 1100 volts grade cable drawn through and in existing surface / recessed PVC conduit and connecting incoming/outgoing electric connections and one run of 10 Sqmm single core PVC insulated but unsheathed multistranded copper conductor FRLS 1100 volts grade cable as earth conductor including taking down old unserviceable submain wiring and making good the disturbed surfaces complete all as specified and directed. Note: Two runs of 10 Sqmm cable, one run of 10 Sqmm earth conductor and one run of PVC conduit of 32mm dia shall be measured and paid as one unit length. |
| 143 | Supply and laying in replacement of Non Metallic Rigid PVC conduit, ISI Marked, conforming to IS 9537, medium grade, size 25 mm dia including all fittings like bends, elbow reducer, junction, coupler boxes, tee bell mouth etc for protection of cables/wires complete in all respect as specified and directed. |
| 144 | Supply and laying in replacement of Non Metallic Rigid PVC conduit, ISI Marked, conforming to IS 9537, medium grade, size 20 mm dia including all fittings like bends, elbow reducer, junction, coupler boxes, tee bell mouth etc for protection of cables/wires complete in all respect as specified and directed. |
| 145 | Supply and laying in replacement of worn out PVC rigid conduit with uPVC trunking/casing caping of size 50mm x 16mm including fittings conforming to IS 14927/2001, fixed to wall/ceiling surface to cover the cable/wire complete all respect as specified and directed. |
| 146 | M&L for cutting chases, pining in making good to facing where required and pointed in CM (1:3) to ends or edges of brick wall etc and cutting chases for concealed conduit wiring etc and making good, match with existing surfaces by applying white/colour wash cutting not exc 10cm girth complete all as specified and directed. |
| 147 | S&F switch piano flush button single pole, one way 5 Amp 240 Volt complete all as specified and directed. |
| 148 | S&F switch piano flush button single pole, one way 15 Amp 240 Volt complete all as specified and directed. |
| 149 | S&F switch piano flush button single pole, two way 5 Amp 240 Volt complete all as specified and directed. |
| 150 | S & F Switch Bell push 5 amp single Pole 230 V all as specified & directed. |
| 151 | S&F socket outlet 6 amps 5 pin flush type, 230 volts complete all as specified and directed. |
| 152 | S&F socket out let, 6 pin 5 and 15 amps multi purpose 2 in 1 flush type 230 volt complete all as specified and directed. |
| 153 | S&F in repair sheet metal enclosure Single pole & neutral with 2 pin and earth plug and socket 20A 240 Volt complete with one single pole MCB of cap 20/25 A, C series complete all as specified and directed. |
| 154 | S&F ceiling rose 63x30 mm three terminal, polycorbonate body complete all as specified and directed. |
| 155 | S&F fan regulator electronic, five step type hum free suitable control speed of fan from 0 to 100% and connecting electrically all as required complete all as specified and directed. |
| 156 | S&F Angle / batten holder polycorbonate type body suitable for batten fitting complete all as specified and directed. |
| 157 | S&F in replacement musical door bell (having locking features) including 2 Nos, AA 1.5 volt battery for working even when no electricity suitable for 230 volts AC supply complete all as specified and directed. |
| 158 | S&F in replacement sketch fitting with decorative, wall mounting, brushed nickel finish fixture with acrylick diffuser including fixing 12 watt rechargable/invertor LED lamp, B22 base cap complete all as specified and directed. |
| 159 | S&F in replacement of LED security / street light, 45 Watt, IP - 66, Impact resistance - IK07, colour temp- 5700 K, Class I in Pressure die-cast aluminium alloy for housing (heat sink) for effective thermal management, sturdiness, excellent corrosion resistant, separate optical and control gear compartment & top opening for easy maintenance. Polyster powder coated grey after phosphochromate treatmentHigh efficiency long life LED modules with SMD LED package mounted on MCPCB. Lumen efficacy of LED >110 lm/W with PC lens to ensure better uniformity of light distribution. Powered by Built-in, Potted electronic LED driver (SMPS based constant current supply) with lower THD, Output Open Circuit protection, Phase to Phase protection, Over Voltage protection, Surge Voltage protection upto 10 kV with external SPD & other safety tests as per IS 15885 Part-2/ Sec13. Suitable for bldg/pole mounting alongwith single arm bracket OD 58 mm (max) with suitable reinforcement on wall height complete in all respect & as directed. |
| 160 | Supply & fixing MS ring hook (I hook) fastener, M-12 size including drilling on RCC roof for fixing ceiling fan complete all as specified and directed. |
| 161 | Supply & fixing in replacement PVC round/circular lid of 65 mm dia including MS screw for covering / closing wiring junction complete all as specified and directed. |
| 162 | Supply & fixing in repair PVC space bar saddle with screw for 20 mm dia conduit on existing wall/ceiling for proper fixing of sagged conduit complete all as specified and directed. |
| 163 | S&F in repairs MCCB, 125 Amp, 4 Pole, 36 KA, 415 volts adjustable thermal & fixed magnetic setting complete all as specified and as directed. |
| 164 | S&F in repairs MCCB, 100 Amp, 4 Pole, 36 KA, 415 volts adjustable thermal & fixed magnetic setting complete all as specified and as directed. |
| 165 | S&F in repairs MCB, 415 volts, 10 KA, 4 Pole, 100 Amps C series complete all as specified and as directed. |
| 166 | Supply & fixing in replacement of MCB DP, 240 Volt, 10 KA, 40 Amps, C series complete all as specified and directed. |
| 167 | Supply & fixing in replacement of MCB DP, 240 Volt, 10 KA, 63 Amps, C series complete all as specified and directed. |
| 168 | Supply & fixing in repair LED constant driver suitable for 2' x 2' LED luminaries of wattage from 30 to 40 watt, 25 to 42 volts DC including fault detection, soldering and testing complete all as specified and directed. |
| 169 | S&F in replacement surface and wall mounted 20 watt LED batten, PVC housing provided for efficient heat dissipation with polycarbonate diffuser & integrated electronic driver complete all as specified and directed. |
| 170 | S&F in replacement 10W integrated LED bulk head luminaire environment friendly, ultra modern, energy saving, surface mounted decorative oval bulk head with LED light, complete all as specified and directed. |
| 171 | S&F in replacement surface and wall mounted 10 watt LED batten, PVC housing provided for efficient heat dissipation with polycarbonate diffuser & integrated electronic driver complete all as specified and directed. |
| 172 | Supply & fixing in replacement ceiling light with 36W Watt, 6000 K, slim LED panel 2' x 2' LED panel for recessed on ceiling) dust-free installation with high brightness LEDs for glare-free homogenous illumination with driver and all other connected accessories complete all as specified and directed. |
| 173 | Supply & fixing in replacement sheet metal enclosure MCB distribution board triple pole & neutral 415 volts 4 way with IP-43 IK-09 protection double door complete with appropriate size bus bar and neutral link, fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and directed. |
| 174 | Supply & fixing in replacement sheet metal enclosure MCB distribution board single pole & neutral 240 volts 12 way with IP-43 IK-09 protection double door complete with appropriate size bus bar and neutral link, fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and directed. |
| 175 | Supply & fixing in replacement sheet metal enclosure MCB distribution board single pole & neutral 240 volts 8 way with IP-43 IK-09 protection double door complete with appropriate size bus bar and neutral link, fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and directed. |
| 176 | Supply & fixing in replacement of MCB single pole 240 volt any rating from 6 to 32 amps, B series with rupturing capacity 10 KA complete all as specified and directed. |
| 177 | S & F modular type 6A one way SP switch 1 module confirming to IS: 3854-1997 with finger proof terminal complete all as specified and directed. |
| 178 | S & F modular type 2/3 pin 6 Amps socket 2 module conforming to IS: 1293-2005 complete all as specified and directed. |
| 179 | S & F modular type 16 A one way SP switch 1 module confirming to IS: 3854-1997 with fingure proof terminal complete all as specified and directed. |
| 180 | S & F modular type 2/3 pin 16 Amps socket 2 module conforming to IS: 1293-2005 complete all as specified and directed. |
| 181 | S&F modular type 3/5 pin socket with one single pole MCB 20 Amp 230 Volts concealed in wall complete all as specified and directed. |
| 182 | S & F modular type 120W step fan regulator of 2 module size conformng to IS: 11037-1984 complete all as specified and directed. |
| 183 | S & F in replacement Modular cover plate 8 modules complete all as specified and directed. |
| 184 | S & F in replacement Modular cover plate 3 modules complete all as specified and directed. |
| 185 | S & F in replacement metal flush box 3 module complete all as specified and directed. |
| 186 | S & F in replacement metal flush box 8 module complete all as specified and directed. |
| 187 | S & F in repair wall lamp, mettalic with chrome finish, diffused glass with 5 to 9 watt LED bulb complete all as specified and directed. |
| 188 | Supply only Hylum sheet 3 mm thick of size 4\\" x 4\\" including screws for fixing complete all as specified and directed. |
| 189 | Supply only Hylum sheet 3 mm thick of size 7\\" x 4\\" including screws for fixing complete all as specified and directed. |
| 190 | Supply only Hylum sheet 3 mm thick of size 8\\" x 10\\" including screws for fixing complete all as specified and directed. |
| 191 | Supply only Hylum sheet 3 mm thick of size 11\\" x 5\\" including screws for fixing complete all as specified and directed. |
| 192 | S & F in replacement of worn out MCB DB VTPN with sheet metal enclosure MCB DB VTPN 4 way with 200 amps rated bus bar 415 volts double door with isolated Neutral Bar & Shrouded bus bar IP protection 43 having door earthing complete all as specified and directed. |
| 193 | Supply and fixing in replacement ceiling fan (5 star rated by Bureau of energy with service value of not less than 6.12) BLDC, (40W±10%) aerodynamically design blades made of compounded ABS to give air friction for silent operation, with air delivery 240 Cum/min, rated speed 280 Rev/min, with or without remote complete with blades, down rods, electronic regulator and accessories, 230 volt, 1200 mm sweep, suitable for single phase supply with noise level 56 db, low voltage, starting input voltage 140 V (Max) with power factor 0.95 complete all as specified and directed. Note : Old unserviceable ceiling fan shall be deposited in AGE E/M store yard. |
| 194 | Supply and fixing in replacement exhaust fans 300 mm sweep metallic body, heavy duty, four blade, double ball bearing, 1400 RPM, minimum air delivery discharge 1710 CMH suitable for SP, 230/250V, 50 Hz AC supply with protective bird guard with louver shutters including grouting of frame in wall and connecting with and including 3 run 1.5 Sq mm single core, PVC insulated but unsheathered FRLSH multistranded copper conductors cable from ceiling rose to exhaust fan complete all as specified and directed.Note : Old unserviceable exhaust fan shall be deposited in AGE E/M store yard. |
| 195 | S&F in replacement Exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230 V, 5 Hz, RPM 1200, copper winding of sweep 300mm complete all as specified and directed.Note : Old unserviceable exhaust fan shall be deposited in AGE E/M store yard. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 24, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 14, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 1 dayAug 21, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 8 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender