Tender For Addition/ Alteration To Certain Rooms In Admin Building At Icgas Chennai Under Ge(I) Cg Chennai
Tender Value
42.50 Lakhs
Estimated cost
Bid Submission
14 Aug 2026
16 days left
EMD
85000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Chennai → Tamil Nadu
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Addition/ Alteration To Certain Rooms In Admin Building At Icgas Chennai Under Ge(I) Cg Chennai
BOQ
| Sl. No. | Item Description |
| 1 | ADDITION ALTERATION B/R WORK |
| 2 | Demolition of floor hearth or wall tiling including cement mortar bedding (but not backing) and removing rubbish off the premises to out side MD land etc., complete all as specified and as directed. |
| 3 | Material and labour for Double charged Virified tiles 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to matchover Screed bed or bedding layer of mortar 15mm of thick CM 1:4 for laying floor finishes |
| 4 | Material and labour for Double charged Virified tiles 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.36 sqmin SKIRTINGS etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over Screed bed or bedding layer of mortar 10mm of thick CM 1:4 for laying floor finishes |
| 5 | Material and labour for coloured Non Skid ceramic tiles, matt finish of grade B-II(a), 7 to 8 mm thick (square/ rectangular), light coloured group, area of each tile exceeding 0.11Sqm but not exceeding 0.18 Sqm, laid in floors of pattern as approved over and including 15mm thick screed bed in Cement mortar 1:6, set and jointed in neat cement slurry and pointed in white or coloured cement to match all as specified and as directed. |
| 6 | Material and labour for glazed coloured ceramic tiles of grade B-III, 7mm thick of size 450mm x 350mm or 350mm x 250mm or of size matching to floor tile as approved by GE, fixed in vertical surfaces such as in skirting/dado set and jointed in neat cement slurry and pointed in white or coloured cement to match floor tile over and including a backing coat in Cement Mortar 1:4, 10mm thick all as specified and as directed. |
| 7 | Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. and removing rubbish off the premises to out side MD land etc., complete all as specified and as directed. |
| 8 | Material and labour for rendering in Cement Mortar 20mm thick in two coats, i.e, in Cement Mortar 1:4, 10mm thick mixed with water proofing compound as per manufacturers' instructions over in Cement Mortar 1:6, 10mm thick on fair faces of brick/concrete surfaces, finished even and fair externally all as specified and as directed.Note: WPC will be measured and paid separately. |
| 9 | Material and labour for rendering 15mm thick in Cement mortar 1:6 on fair faces of brick work or concrete surfaces and finished the surfaces even and smooth without using extra cement etc., complete all as specified and as directed. |
| 10 | Material and labour for rendering 5mm thick in Cement mortar 1:3 on fair faces of concrete surfaces in ceilings, Chajja surfaces and finished even and smooth without using extra cement complete all as specified and as directed. |
| 11 | Supply only integral water proofing compound of approved quality. |
| 12 | Material and labour for preparation of newly plastered surface of walls including pilasters and cornices etc., and Distempering two or more coats with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour all as per manufacturer's specification etc., complete all as specified and as directed. |
| 13 | Material and labour for preparation of newly plastered surface of walls including pilasters and cornices etc and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10sqm over new surfaces complete all as specified and as directed. |
| 14 | Material and labour preparation of newly plasterred surfaces of walls and applying three coats of white wash complete all as specified and as directed. |
| 15 | Excavating in trenches not exceeding 1.5 metre wide and not exceeding 1.5 metre in depth for laying of under ground cables, pipes/pipe lines, etc. and the like not exc. 10 Sqm on plan and not exc 1.5m in depth and getting out in hard/dense soil complete all as specified and as directed. |
| 16 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in any type soil complete all as specified and as directed. |
| 17 | Removing Excavated soil to a distance execeeding 250m but not exceeding 500m and depositing where directed at a level not exe 1.50 m above the starting point complete all as specified and as directed. |
| 18 | Material and Labour for Plain cement concrete 1:4:8, type D2 using 40 mm graded stone aggregate as in foundation filling as mass concrete complete all as specified and as directed. |
| 19 | Material and Labour for Sand filling under floors or in foundations including watering and consolidation complete all as specified and as directed. |
| 20 | Supply and Fix 110mm bore UPVC (SWR) pipe of pressure not less than 4Kg/Sqcm in single socketed, in any length with rubber ring joints, fixed to wall,ceiling and foors including distance pieces and stack clamp with nuts & bolts complete all as specified and directed. |
| 21 | Supply and Fix UPVC (SWR) reducers any radius 110mm bore complete all as specified and as directed. |
| 22 | Supply and Fix 110mm bore UPVC (SWR) junction, single (single T) equal or unequal with door access complete all as specified and as directed. |
| 23 | Demolition of Brickwork or stone/boulder masonry, built in cement mortar or cement lime lime mortar including all quoins, arches, pillars,etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and as directed. |
| 24 | Material and labour for Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified and as directed. |
| 25 | Supply and fix framed work such as grills, etc, with ends of bars or forged int spikes framed guard bars; barred iron doors ladders framed balusters, walk ways, railings framework of water tanks and similar work conforming to Fe-290, Gde E-165 complete all as specified and directed. |
| 26 | Material and Labour for preparing of new steel surfaces of any description over 10 cm width or girth and applying two coat of synthetic enamel paint over one coat of red oxide complete all as specified and directed. |
| 27 | Demolition of reinforced cement concrete of any description and in any postion not otherwise specifically for complete all as specified and as directed. |
| 28 | Material and Labour for Reinforced Cement Concrete 1:2:4, (nominal mix) type B1 using 20mm grades stone aggregate as in chajja, lintels, shelves and the like complete all as specified and as directed.Note: Reinforcement bars shall be measured and paid separately. |
| 29 | Material and labour for Formwork to sides and soffits of floor or roof beams, lintels, cantilevers, shelves and similar items including edges flat rough finished surfaces of concrete all as specified and as directed. |
| 30 | Material and labour for High strength Mild steel Deformed Steel Bars produced by Thermo Mechanical Treatment process [TMT] of grade Fe-500D in reinforcement, 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to Fe-500D all as specified and as directed. |
| 31 | Material and labour for Granite stone slab 18-20mm thick (black galaxy) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms,verandah including nosing and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over a screed bed of 15mm thick cement mortar 1:4 including nosing half round bullnose finish at edges etc., complete all as specified. |
| 32 | Providing edge moulding to 18 to 20mm thick of granite stone of counters vanities etc., including machine polishing to edge to give high gloss finish etc., complete all as specified and as directed. |
| 33 | Supply and fix in repairs Powder coated aluminium sections for frames and shutters of doors, windows (two track/ three track sliding windows, side hung openable windows, pull and push type shutters), ventilators, partitions etc., having thickness of powder coating not less than 50 micron and colour as approved by GE/ Engineer-in-Charge including necessary joining cleats, glazing clips, powder coated aluminium snap beading, screws, rollers & interlocking handles for sliding shutters and taking down damaged unserviceable frames and shutters etc., complete all as specified and as directed. Note : Powder coated Aluminium deco grill, rubber beadings, solar control film, builders hardware like hinges, tower bolts, handles etc., prelaminated particle boards, Sheet glass panes and wire mesh shall be measured and paid separately. |
| 34 | Supply and fix of 5mm thick plain sheet glass, ordinary quality and glazing with oil putty in square any size in each pane complete all as specified and as directed. |
| 35 | Material and labour for 18/19mm thick Prelaminated particle board, interior grade, prelaminated both side with decorative choice lamination & other side balancing white lamination with lipping fixed with screws to timber frame work in repairs rate including neccesary fittings like soft close hinges,handles etc., complete all as specified and as directed. |
| 36 | Demolition of unreinforced cement concrete in ground floor and pavings n.exc. 15 cm thick (below or above GL) complete all as specified and as directed. |
| 37 | Materials and labour for 75mm thick Plain Cement Concrete 1:3:6, type C-2 using 40mm graded stone aggregate as in plinth protection surfaces finished even and smooth without using extra cement complete all as specified and as directed. |
| 38 | Material and labour for PCC 1:4:8, type D-2, 75mm thick using 40mm graded stone aggregate as in sub base under floor etc., complete all as specified and as directed. |
| 39 | Material and labour for Chequered cement concrete tiles (Ultra) of any size/shape, 30cmx 30cm and 22-25mm thick, set and jointed in neat cement slurry in floors and pointed with grey cement and pigments match to tiles laid over and including 20mm thick screed bed in cement mortar 1:4 complete all as specified and as directed. |
| 40 | Supply and fix in repairs Stainless steel kitchen sink of over all size 915mm x 460mm or next higher size with draining board and bowl size 410mm x 330mm x 160mm made out of 1mm thick stainless steel sheet of grade AI SI-304 with plugs, washers, waste coupling and 38/40mm bore LDPE waste pipe, fixed over CI cantilever brackets or bedding in cement mortar to dwarf wall as required and connecting union to pipe etc., compete all as specified and as directed. |
| 41 | Supply and Fix PVC waste pipe/Flush pipe 32 mm dia, 600mm long for urinal/WHB with fitting etc., complete all as specified and as directed. |
| 42 | Supply and fix in repair 15mm bore pillar tap fancy type, cast copper alloy with capstan heads, chromium plated screwed down, high pressure, with or without lettered hot or cold with long screwed shanks and fly nuts screwed for iron pipes complete all as specified and as directed. |
| 43 | Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stones, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and as directed. |
| 44 | Supply and Fix 4 mm thick plain sheet glass ordinary quality and glazing with rubber packing around the glass, in squares not exceeding 0.50 sqm in each pane complete all as specified and as directed. |
| 45 | Supply and fix 4 mm thick figured sheet glass and glazing with rubber packing around the glass, in squares not exceeding 0.50 sqm in each pane complete all as specified and as directed. |
| 46 | Supply and Fix solar control film 25 micron reflective type sticked to glass panes as per manufacturers instruction complete all as specified and directed. |
| 47 | Taking down chowkats (or) frames of any description with shutters (without taking off shutters from the frame) of area not exc.1.5 sqm each along with fittings including separating guard bars/grills/ wire mesh etc., complete all as specified and as directed. |
| 48 | Taking down chowkats (or) frames of any description with shutters (without taking off shutters from the frame) of area exc.1.5 sqm not exc 4sqm each along with fittings including separating guard bars/grills/wire mesh etc., complete all as specified and as directed. |
| 49 | Material and labour for Providing and fixing factory made uPVC white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (± 0.2mm), Window profile with hollow section with multi chamber, Frame (88mm x 52mm), sliding sash (42mm x 67mm), Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2 ± 0.2mm thick galvanised steel Frame (30mm x 18mm) 2 Nos., sliding sash (30mm x18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system, Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and 5mm thick plain sheet glass including necessary accessories complete all as specified and as directed.Note: [a] The unit rate quoted by contractor shall include the cost of 5mm thick sheet glass, wiremesh and all other connected accessories. [b] Net Opening will be measured for payment purpose. |
| 50 | Supply and Fix 12mm thick clear toughened glass with double leaf glass door H polish. single connector aqnd door lock, over panel badge, holes cutout, silicon (H shape 600x32) mm handle godrej floor spring and other patch work in main entrance of building including transportation charges complete all as specified and direceted by Engineer in charge. |
| 51 | Supply and Fix 12mm thick tinted toughened fixed frameless window glass H polish wall groove cutting section all patch up work in windows including transportation charges complete all as specified and direceted by Engineer in charge |
| 52 | Supply and Fix 12mm thick frosted toughnend frameless glass door H polish, Floor spring, door lock,top badge pivot (H-shape 600X32)mm handle godrej floor spring cutout silicon and all other patch up work including transportation charges complete all as specified and direceted by Engineer in charge |
| 53 | Material and labour for plain cement concrete 1:2:4, type B1 using 20 mm graded stone aggregate as in lintels upto 1.5 m clear span, cills, steps, copings, bed platesand the like including weathering, slightly rounded for chamfered angles and throating complete all as specified and as directed. |
| 54 | Supply and fixing 12mm thick Wood Polymer Composite (WPC) Louver Wall Panelling of approved make and pattern, manufactured from wood fibre and polymer composite, with plain/grooved/wood-grain embossed surface finish, fixed over aluminium/GI sub-frame with approved stainless steel screws, clips, fasteners and necessary accessories complete. The WPC louvers shall be moisture resistant, termite resistant, warp resistant and maintenance free, having matt/semi-matt finish in approved shade. The item includes all framework, edge trims, corner mouldings, cutting, fitting, alignment, levelling and finishing complete in all respects, as approved by and directed by the Engineer-in-Charge. |
| 55 | ADDITION ALTERATION E/M WORK |
| 56 | Taking down carefully existing point wiring with Aluminium/copper conductor on batten/surface conduit/casing caping point wiring (light/exhaust fan/socket/call bell/Power point) complete including fittings and fixtures and removing the materials to store for taking credit including making good the disturbed surfaces of walls/floors/ceilings etc. complete all as specified and as directed. Please Enable Macros to View BoQ information |
| 57 | Taking down carefully existing point wiring with Aluminium/copper conductor on batten/surface conduit/casing caping point wiring (light/exhaust fan/socket/call bell/Power point) complete including fittings and fixtures and removing the materials to store for taking credit including making good the disturbed surfaces of walls/floors/ceilings etc. complete all as specified and as directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 24, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 14, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 16 daysAug 17, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 19 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender