Tender For special Repairs To Bldg No T-183, T-177, T-565 & T-465 And Provn Of One Addn & Bathroom With special Sanitary Fittings To Bldg No P-38 At Old Cantt Under Ge Gangtok
Tender Value
38 Lakhs
Estimated cost
Bid Submission
05 Aug 2026
5 days left
EMD
76000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
sikkim → Sikkim
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for special Repairs To Bldg No T-183, T-177, T-565 & T-465 And Provn Of One Addn & Bathroom With special Sanitary Fittings To Bldg No P-38 At Old Cantt Under Ge Gangtok
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of cement concrete (un reinforced) in ground floors and paving n. exc. 15cm thickness (below or above ground level) removing rubbish off the premises etc complete all as directed. |
| 2 | Demolition of brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as directed. |
| 3 | Dismantling timber scantlings 40 Sq.cm and over in section, in any position complete all as specified and as directed. |
| 4 | Taking down chowkhats or frame with shutters (without taking off shutters from the frame) not exceeding 1.50 Sqm each complete all as directed. |
| 5 | Taking down chowkhats or frame with shutters (without taking off shutters from frames) exceeding 1.5 Sqm but not exceeding 4 Sqm each complete all as directed. |
| 6 | Taking down shutters of any description exceeding 1 Sqm but not exceeding 2 Sqm each complete all as directed. |
| 7 | Dismantling of plain or corrugated steel sheeting, any gauge, thickness, in roof covering including ridges complete all as specified and as directed. |
| 8 | Taking down cement plaster or cement lime plaster on walls /ceiling of any description from concrete or brick wall etc including raking out joints, hacking for key, scrubbing down with water and disposing off the retreived debris as directed including necessary scaffoldings etc complete all as directed. |
| 9 | Taking up or down 15mm dia steel tubing and connections, including cleaning for refixing or removal complete all as directed. |
| 10 | Taking up or down 20mm dia steel tubing and connections, including cleaning for refixing or removal complete all as directed. |
| 11 | Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil complete all as specified and as directed. |
| 12 | Excavating in trenches not exc 1.5m wide and n.exc 1.5 m in depth, for foundations, etc, or for shafts, wells, cesspits, manholes, pier holes, cable trench etc and not exceeding 10 square meter on plan for manholes etc and not exceeding 1.5m in depth and getting out in soft/loose soil complete all as specified and directed. |
| 13 | Returning filling in with approved excavated soil including spreading, leveling, watering and well ramming in layers not exceeding 25cm thick complete all as specified and directed. |
| 14 | Removing excavated soils to a distance not exceeding 50 metres and depositing where directed at a level n. exc. 1.5 metre above the starting point complete all as specified and directed. |
| 15 | M&L for Hardcore of gauge not exceeding 63 mm, deposited, spread and levelled in layers not exceeding 15cm thick, watered and rammed to a true surface with Broken stone or boulders complete all as specified and as directed. |
| 16 | M&L for cement concrete (1:4:8) type D-2 (using 40 mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified and as directed. |
| 17 | M&L for PCC (1:3:6), type C2 (using 40mm graded stone aggregates) as in surfaces channels and drains incl necessary formwork complete all as specified and directed. |
| 18 | Extra for forming fair finished drain or channel 30 cm inner girth cement concrete using extra cement including forms moulds mitred and stopped ends etc complete all as specified and directed. |
| 19 | M&L for precast cement concrete block massonary (1:3:6) type C1 (using 20 mm graded stone aggregates) with solid blocks exc 10 cm in width and setting in cement morter 1:6 complete all as specified and directed. |
| 20 | M&L for RCC M-25 (Design Mix) using 20mm graded stone aggregates as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and as directed |
| 21 | M&L for RCC M-25 (Design mix) using 20mm graded stone aggregates as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and as directed |
| 22 | M&L for walling of RR stone masonry uncoursed, well bonded, bedded and solidly hearted built in CM 1: 6 incl brought upto course at interval of every 60cm complete all as specified and as directed. |
| 23 | Use and waste of Formwork to sides of concrete foundations, footings bases of columns below GL and similar work, rough finished surfaces of concrete complete all as specified and directed. |
| 24 | Use and waste formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc.; vertical or to batter complete all as specified and as directed. |
| 25 | Use and waste of form work to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. rough finished flat surface of concrete complete all as specified and as directed. |
| 26 | M&L for 2nd class hard wood plain, solid, straight chowkhats and frame wrought framed rebated on the soild, rounded or chamfered, put together with glue, pinned at joints, complete all as specified and directed. |
| 27 | S&F 30mm thick flush door shutters solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed. |
| 28 | S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing, complete all as specified and directed.. |
| 29 | S&F actory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification and drawing, complete all as specified and directed. |
| 30 | S&F Fiber Glass Reinforced plastic (FRP) Door Frames of cross section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminte shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame., complete as specified by the manufacturer and as per directions of Engineer-in-charge. → |
| 31 | S&F 30 mm thick Fiberglass Reinforced Plastic (F.R.P.) flush door shutter in different plain and wood finish made with fire retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate all around, with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF)/Polystyrene foam to be used as filler material throughout the hollow panel, casted monolithically with testing parameters of F.R.P. laminate conforming to table 3 of IS: 14856 complete all as specified by the manufacturer and as per directions of Engineer- in-charge. |
| 32 | S&F 150 mm long, aluminium, barrel tower bolts of extruded section of aluminium alloy, anodised finish not be less than Grade AC 10 of IS 1868:1996 with transparent anodic film complete all as specified and as directed. |
| 33 | S&F 100 mm long, aluminium, barrel tower bolts of extruded section of aluminium alloy, anodised finish not be less than Grade AC 10 of IS 1868:1996 with transparent anodic film complete all as specified and as directed. |
| 34 | S&F Mild steel butt hinges, Medium grade, 75 mm size , complete all as specified and directed. |
| 35 | S&F Mild steel butt hinges, Medium grade, 100 mm size , complete all as specified and directed. |
| 36 | M&L for 100mm size extruded brass type B-21 butt hinges with Aluminium alloy with galvanised mild steel hinge pin anodised and fixed complete all as specified and directed. |
| 37 | S&F extruded aluminium alloy handles, fabricated type, anodized, 150 mm size , complete all as specified and directed. |
| 38 | S&F extruded aluminium alloy handles, fabricated type, anodized, 125 mm size , complete all as specified and directed. |
| 39 | S&F 250 mm long aluminium anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded sections or cast aluminium complete all as specified and as directed. |
| 40 | M&L for TMT bars 10 mm dia and over, as reinforcement for concrete cut to length, bent to shape required including cranking, bending, spirally hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia, complete all as specified and directed. |
| 41 | M&L for TMT bars 6 to 10 mm dia in stirrups, spacers and binders, as reinforcement for concrete cut to length, bent to shape required including cranking, bending, spirally hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia, complete all as specified and directed. |
| 42 | S&F rolled mild steel section sections any type as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates, FE -290 Gde E-165, complete all as specified and as directed. |
| 43 | S&F rolled mild steel in roof trusses (framed), trussed, purlins, crane gantries, rails and fastening and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. steel conforming to Fe 410-W (Gde-E-250) quality A complete all as specified and directed. |
| 44 | S&F steel windows with side hung shutters including box type hinges with steel handle and steel peg stay complete with glazing bars, dovetailed or welded complete all as specified and as directed. |
| 45 | M&L for anodised aluminium window and ventilator shutters, fixed type, with or without sash bar, using aluminium section weighing not less than 0.55Kg per metre including necessary joining cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading, screws etc complete all as specified and as directed. |
| 46 | S&F Pre-painted galvalume aluminum zinc coating (AZ-150) GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed. |
| 47 | S&F Pre-painted galvalume aluminum zinc coating (AZ-150) GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws , complete all as specified and directed. |
| 48 | M&L for 75 mm thick, plain cement concrete (1:3:6) type C-2 (using 40mm graded stone aggregates) as in plinth protection/ hard standing etc, finishing cement concrete surface even and smooth without using extra cement including making joints with bitumastic filing in proportion of bitumen and sand (1:2) complete all as specified and as directed. |
| 49 | M&L for 75 mm thick plain cement concrete (1:3:6), type C2 (using 40mm graded stone aggregate) as in sub base of floor, etc complete all as specified and as directed. |
| 50 | M&L for 75mm thick PCC (1:4:8) type D-2 (using 40mm graded crushed stone aggregate) as sub base of flooring complete all as specified and directed. |
| 51 | M&L for 40 mm thick, plain cement concrete (1:2:4) type B-1 (using 20 mm graded stone aggregate) as in sub base finishing cement concrete surface even and smooth without using extra cement complete all as specified and as directed. |
| 52 | M&L for 25 mm thick PCC 1:2:4 type B-1 (using 20 mm graded stone aggregates) as in floor finishing cement concrete surface even and smooth without using extra cement complete all as specified and as directed. |
| 53 | M&L for 20mm thick granite slabs of any type (table rubbed and polished) on cooking platforms and like, set and jointed in net cement slurry and pointed in white cement (1:2) using marble dust with admixture of pigment to match shade of granite including necessary moulding at edges laid over and including 20mm thick cement mortor screed bed in cement mortor (1:6) complete all as specified and directed. |
| 54 | M&L for rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and as directed. |
| 55 | M&L for non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles with and including 15mm thick screed bed or bedding layer of cement morter (1:6) for laying of floor finishes complete all as specified and directed. |
| 56 | M&L for non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles with and including 15mm thick screed bed or bedding layer of cement morter (1:6) for laying of floor finishes complete all as specified and directed. |
| 57 | M&L for coloured 450x350x7-8 mm thick glazed ceramic tiles on vertical surfaces such as skirting,dado and risers to steps etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match, over and including 10mm thick backing coat in cement mortar (1:4) complete all as specified and directed. |
| 58 | M&L for rendering 15mm thick in cement morter (1:6) on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement, complete all as specified and directed. |
| 59 | M&L for rendering 20 mm thick on fair faces of external wall of brick work or stone surfaces in two layers (10mm thick each layer) in cement mortar in (1:4) using water proofing compound in top layer and finished even and smooth (without using extra lime or cement) complete all as specified and directed.Note: Water Proofing Compound measured and paid separately. |
| 60 | Supply only liquid Water Proofing Compound of approved make complete all as specified and directed. |
| 61 | M&L for preparing newly plastered surfaces of walls etc. and applying three coats of white wash complete all as specified and directed . |
| 62 | M&L for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper of approved colour with roller over one coat of primer complete all as specified and directed. |
| 63 | M&L for preparation of newly plastered surfaces of walls and applying two coats of cement paint over a coat of suitable primer complete all as specified and directed. |
| 64 | S&F 3mm thick sheet glass, ordinary quality and glazing with oil putty in squares n.exceeding 0.50sqm in each pane complete all as specified and directed. |
| 65 | S&F 3mm thick Figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane etc complete all as specified and directed. |
| 66 | M&L for preparing of new steel surfaces of any description , over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed. |
| 67 | S&F 15mm bore medium grade galvanized steel water tubing with all fittings, fixed to wall/ceiling or laid in floor complete all as specified. |
| 68 | S&F 20mm bore medium grade galvanized steel water tubing with all fittings, fixed to wall/ceiling or laid in floor complete all as specified. |
| 69 | S&F 25mm bore medium grade galvanized steel water tubing with all fittings, fixed to wall/ceiling or laid in floor complete all as specified. |
| 70 | S&F 40mm bore pipe galvanized iron medium grade complete with all fittings fixing on wall, jointed tested and commissioned complete all as specified and directed. |
| 71 | Cutting existing steel tubing for alteration (Each cut measured) including Screwing existing steel tubing for alterations or additions (or lengthening screw on pipe to form connector) done in position without taking down complete all as directed. |
| 72 | Supply and laying of CPVC pipes SDR11 & Plain CPVC SDR 11 fitting on wall /ceiling or laying in floors etc of outer dia 16 mm dia complete all as specified and directed |
| 73 | Supplying and laying 20mm dia CPVC pipes SDR 11 & plain CPVC SDR 11 fittings in trenches complete all as specified and directed |
| 74 | Supplying and laying 25mm dia CPVC pipes SDR 11 & plain CPVC SDR 11 fittings in trenches complete all as specified and directed |
| 75 | S&F brass tee of CPVC pipe outer dia 16mm complete all as specified and directed |
| 76 | S&F 20mm outer dia of CPVC pipe Female brass threaded adaptor (FTA/FBTA) etc complete all as specified and directed. |
| 77 | S&F 15mm fancy type Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed etc complete all as specified and directed . |
| 78 | S&F in repairs Bip tap standard of PTMT any colour screwed for iron pipe and fixed (Minimum weight 15mm - 90gms) complete all as specified and as directed. |
| 79 | S&F stop valves, cast copper alloy , screwed down , high pressure , with crutch or butterfly handle , screwed both ends for iron or for unions and fixed to size 15mm complete all as specified and directed |
| 80 | S&F concealed stop valves fancy type 15 mm bore cast copper alloy, screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for pipe or for unions and fixed.complete all as specified and directed by the Engr-in-Charge. |
| 81 | S&F in repair gun metal gate valve of size 25mm bore iron wheel head screwed both ends for iron pipe and fixed including all as specified and directed. |
| 82 | S&F for 15 mm bore Angle stop valve of PTMT any colour high pressure screwedfor iron pipe and fixed, (Minimum weight 15mm-90gms)complete all as specified and directed. |
| 83 | S&F in repairs Vitreous China squatting pan, `Orrisa' pattern, size 580 x440 mm white, with integral foot rests (excluding flushing cistern & flush pipe) incl setting the trap and pan in cement mortar (1:3:6) all round and \\"P\\" or \\"S\\" Trap, complete all as specified and directed. |
| 84 | S&F Snow white one piece vitreous china wash down water closet EWC pan (pedestal pattern) of size 360X655X765mm with 'P' or 'S' Trap concealed including soft close seat cover, dual flush cistern fittings etc complete all as specified and directed. |
| 85 | S&F for PVC low level flushing cistern of 10 ltrs capacity action type white body with intel ball valve float handle bracket flush pipe etc complete and connecting to WC with PVC flushing pipe complete all as specified and directed. |
| 86 | S&F PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed. |
| 87 | S&F PVC connections 15mm size with PTMT nuts of length 600mm complete all as specified and directed. |
| 88 | S&F 110 mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed. |
| 89 | S&F PVC (SWR) pipes 75mm dia, single socketed, in any length with rubber ring joints laid in trenches complete all as specified and directed. |
| 90 | S&F 75 mm dia PVC (SWR) bends of any radius fixed to PVC Pipe complete all as specified and directed by the Engr-in-Charge. |
| 91 | S&F 75mm dia PVC (SWR) vent cowl etc complete all as specifed and directed. |
| 92 | S&F 110 mm PVC (SWR) 'P' or 'S' trap complete all as specified and directed. |
| 93 | S&F Cast iron Nahani trap 100 mm outet dia, with grating including jointing to waste pipe fixed in cement concrete (1:2:4) type B1 complete all as specified and directed. |
| 94 | S&F toilet paper holderof vitereous china fixed to wall with chromium plated (CP) brass screws etc complete all as specified and directed. |
| 95 | S&F Soap dish, vitreous China white, approximate size 160x 160x90mm. any type, fixed to plugs with chromium plated brass screw complete all as specified and directed. |
| 96 | S&F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long etc cmplete all as specified and directed. |
| 97 | S&F 600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers etc complete all as specified and directed. |
| 98 | S&F 08-10mm thick PVC ceiling/wall panels of interlocking types, width 250/255 mm with lamination design and exc 60% of PVC content including necessary H-joints, internal/external corner trim, coner cove, F/J edge trims where required fixed including screws to steel/wooden frame work complete all as specified and directed. |
| 99 | S&F bibtap spout with button attachment for handshower with wall flange etc complete all as specified and directed. |
| 100 | S&F CP Rain Shower (over head) with rubit cleaning system, size 100x100mm square shape single flow including shower arm of 20mm dia and 400mm long complete all as specified and directed. |
| 101 | S&F single lever hi flow diverter with operating lever cartirdge sleeve wall flange with suitable assembly etc complete all as specified and directed. |
| 102 | S&F CP Hand Shower with rubit cleaning system, size 100mm round shape single flow including 1.5m long flexible stainless steel hose with nuts etc complete all as specified and directed. |
| 103 | S&F for 12 mm thick frameless double leaf toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and and making necessary holes etc. for fixing required door fittings and lock,and necessary sliding arrangement etc complete all as specified and directed. |
| 104 | S&F Hand Wash basins, Vitreous China (Table top) of size 420x420x155mm inlcuding waste coupling etc complete fitting complete all as specified and directed. |
| 105 | S&F single liver CP basin mixer without popup waste system with 450mm long braided hoses including all fittings complete all as specified and directed. |
| 106 | S&F Tubular towel rail, 20mm dia, D type, 60cm long between flanges of brass chromium plated complete all as specified and directed. |
| 107 | S&F towel rack 600mm long without lower hangers but with 3 hooks, stinless steel complete all as specified and directed. |
| 108 | S&F corner glass shelf (with bracket) etc complete all as specified and directed. |
| 109 | E/M Works Taking down carefully copper / aluminium point wiring (light, fan, socket or power) complete along with fittings such as switches, Sockets, ceiling rose, lamp holder, tube light fittings and making good distrubed surfaces on walls etc. complete all as directed. |
| 110 | M&L for concealed modular point wiring with FRLSH PVC insulated unsheathed multistranded copper conductor cables of 1.5 sqmm size alongwith one earth continuity conductor with FRLSH PVC insulated unsheathed multistranded copper conductor cable of 1.5 sqmm size passing through and including suitable PVC conduit with all fittings and accessories of PVC conduit (like Tee, bend etc.) complete fixed to walls /ceiling etc , including cutting chases, making good with cement mortar 1:3, terminated in and including providing modular metal flush box of suitable size for fixing of modular switches, sockets, fan regulators etc for one light/fan/bell/buzzer point controlled by one, one way switches complete all as specified and as directed. |
| 111 | All as per Item No.110 here in above but for One 2/3 pin socket outlet 5/6Amps on independent board |
| 112 | All as per Item No.110 here in above but for one switch socket combination 15/16 Amps on independent board with cable 4 sq mm size and earth wire 4 sqmm |
| 113 | M&L for point wiring with 1.5 Sqmm (nominal area), FRLSH PVC insulated, multistranded, single core unsheathed, copper conductor cables passing through and including PVC casing caping with all fittings and accessories of PVC casing caping (like Tee, bend etc.) fixed to walls /ceiling etc. with and including 1.5 Sqmm (nominal area) FRLHS PVC insulated, unsheathed, stranded, single core, copper cable green in colour as earth continuity wire connecting to common earth point terminated in and including 1.6mm thick mild steel sunken terminal box of suitable size with 3mm thick hylam sheet top cover fixed with suitable size of brass screws suitable sizes cadmium plated iron screws and washers etc.for mounting switches, sockets, regulators etc complete for one light/fan/bell/buzzer point controlled by one ,one way switches complete all as specified and as directed. |
| 114 | All as per Item No.113 here in above but for One 2/3 pin socket outlet 5/6Amps on independent board |
| 115 | All as per Item No.113 here in above but for one switch socket combination 15/16 Amps on independent board with cable 2.5 sq mm size and earth wire 2.5 sqmm |
| 116 | S&F switch piano, flush type, 5 amps, 230 volts, single pole, one way (ISI marked) complete all as specified and as directed. |
| 117 | S&F Switch socket combination 2 in 1, 5 Amps flush type, ISI marked complete all as specified and as directed. |
| 118 | S&F switch socket out let combination multipurpose 3/5 pin, 15/16 Amps and (with 3 pin 5 Amps outlet also) flush type (non shuttered) complete all as specified/directed. |
| 119 | S&F switch Modular type, 5 amps, 230 volts, single pole, one way (ISI marked) complete all as directed by Engineer-in-charge |
| 120 | S&F Modular switch 1 way 16 A, 1 module 230 Volts,50Hz, ISI marked all as specified and as directed. |
| 121 | S&F modular white cover plate with frame 2 module, ISI marked complete all as specified and as directed. |
| 122 | S&F modular white cover plate with frame 3 module, ISI marked complete all as specified and as directed. |
| 123 | S&F modular white cover plate with frame 4 module, ISI marked complete all as specified and as directed. |
| 124 | S&F Socket, 6A-2/3 pin combined 2 module 230 Volts, 50Hz, ISI marked complete all as specified and as directed. |
| 125 | S&F Modular Socket, 6A/16A-2/3 pin combined 2 module 230 Volts, 50Hz, ISI marked complete all as specified and as directed |
| 126 | S&F Ceiling rose, PVC/polycarbonate insulated body, 3 terminal and 240 volts, ISI marked complete all as specified and directed. |
| 127 | S&F LED light fitting 1 x 18 W (4 FT), CRI >=80, CT >=5700K, wall / surface mounted, integrated type, constructed of fire retardant engineering grade extruded plastic & decorative end caps with integrated high efficiency electronic driver & surge suppressor of 2 KV or more, luminaire efficacy > 95 lumens/Watt, power factor >/ 0.90, operating range – 140 to 270 V, 50 Hz fixed with suitable fixing arrangements complete including 01 No 18 W (4 FT) LED lamp with all accessories internally prewired and including connecting up with and including twin core twisted flexible copper conductor cable of suitable size all as specified and as directed. |
| 128 | S&F round shape 15 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete. |
| 129 | S&F water proof 10 watt LED bulk head 1x10W bulkhead luminaries including LED light driver holder connecting up with three core flexible copper conductor cable fo suitable size complete all as specified andas directed by Engr-in-Charge. |
| 130 | S&F Lamp holder angular/straight insulated body, with back plate suitable for batten fittings, white/ivory finish complete all as directed. |
| 131 | S&F LED retrofit lamp B22 holder base with polycarbonate body and aluminium heat sink of 09/10W all as specified and as directed. |
| 132 | S&F LED Mirror lights light fitting with high out put diffuser 2 feet , 10 watt 220 v AC decorative type with driver holder and LED lamp including connecting up with driver three core flexible copper conductor cases suitable size complete all as specified. Make havells/bajaj/philips |
| 133 | S&F in repairs LED street light 25W, made up of pressure die cast aluminium housing with high power LED as lighting source and lens embeded PC cover having top opening separate driver compartment with IP 66 protection and impact resistance of IK07 having 1.5 mtr GI pipe with two coat of painting complete all as specified and directed. |
| 134 | Taking down carefully old existing unserviceable DB any description with MCBs complete all as specified and directed. |
| 135 | S&F sheet metal enclosure for 8 way Distribution Boards (DB’s), single pole and neutral double door with IP-43 protection suitable for fixing MCB's/lsolators complete all as specified and as directed. |
| 136 | S&F sheet metal enclosure for 4 way Distribution Boards (DB’s), single pole and neutral double door with IP-43 protection suitable for fixing MCB's/lsolators complete all as specified and as directed. |
| 137 | Supply & fix MCB DB 4 way TPN with 200 A rated bus bar,415 Volts, Double door complete. |
| 138 | S&F MCB single pole 6 to 32 Amps, 240 Volts, 10 KA rapturing capacity, 'C' Curve complete all as directed by Engineer-in-charge. |
| 139 | S&F MCB single pole & neutral 40 to 63 Amps, 240 Volts, 10 KA rapturing capacity, 'C' Curve complete all as directed by Engineer-in-charge. |
| 140 | S&F MCB tripple pole & neutral 63 Amps, 240 Volts, 10 KA rapturing capacity, 'C' Curve complete all as directed by Engineer-in-charge. |
| 141 | M&L for earthing complete with galvanized steel earth plate electrode 600x600x6 mm thick, burried directly in ground (earth pit not less than 2.25 mtr deep below ground level) with top edge of the plate not less 1.5 mtr deep below normal ground level connected to GI earth wire 4 mm dia connected to earth plate by means of nut, bolts, check nut & washer of galvanized iron or of steel, GI earth wire will be protected by 15 mm dia GI pipe 'light grade', watering pipe 20 mm dia GI 'Medium grade', GI wire meshed funnel, alternate layer of char coal and salt on all side to earth plate upto thickness of 150 mm, filling of black cotton soil in earth pit upto ground level, PCC chamber recessed for and including RCC cover including all necessary excavation & earth work, earth wire connected to O/H continious earth wire on pole, testing the earthing after completion all as specified and shown in electric plate No 3 of MES SSR Part-I 1991 print and as directed . |
| 142 | Taking down carefully unserviceable sub main wiring of any size/core/type including making good the disturbed surfaces all as directed. |
| 143 | M&L for sub main wiring with two run of 6 Sqmm (Nominal area) single core cable PVC insulated, multistranded, unsheathed, copper conductor cables (FRLSH), 1100 Volts grade drawn through PVC casing-caping/conduit of suitable size, fixed to wall/ceiling etc including one run of 6 Sqmm (nominal area) single core, PVC insulated, multistranded, unsheathed, copper conductor (FRLSH) as earth wire and duly connected to common earth point complete all as specified and as directed.Note : (a) PVC Casing-caping/conduit, two run wiring cables and one run of earth wire will be measured as one length (b) All incoming and outgoing cable shall be connected by using proper lugs & sockets. |
| 144 | S&F electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 star rated complete with all accessories such as saftey valve, thermostate, NRV, connection piece all as specified and as directed. |
| 145 | S&F non metallic Ventilating Fans, 200 mm sweep 900 rpm,AC single phase, 230 volts including louver connection with multistranded copper conductor flexible wire of suitable size from ceiling rose, necessary fixing arrangement i.e anchor nut, bolt, washer and grouting and making good to disturbed surface complete all as specified and as directed.Make : Havells//Khaitan/Almonard/Bajaj/Crompton Greaves |
| 146 | Supply, Laying, jointing & testing in trenches/through pipes/ducts or on poles/walls jointing to O/H conductor, LT panels, main switch with cable size aluminum lugs and testing. XLPE insulated, armoured heavy duty electric cables with aluminum conductor, 1100 volt grade, all as specified directed by Engineer in charge of cross sectional area of 10Sqmm 2 core |
| 147 | Supply, Laying, jointing & testing in trenches/through pipes/ducts or on poles/walls jointing to O/H conductor, LT panels, main switch with cable size aluminum lugs and testing. XLPE insulated, armoured heavy duty electric cables with aluminum conductor, 1100 volt grade, all as specified directed by Engineer in charge of cross sectional area of 16 Sqmm 4 core |
| 148 | Supply and laying of DWC pipe,ISI marked in trenches or in cable ducts or fixed on walls using clamps along with all accessories like socket,bend,couplers etc confirming to IS 14930,part-II complete with fitting cutting,jointing etc of size 50 mm outer dia complete all as specified and directed by Engr-in-Charge Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 24, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 05, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 5 daysAug 10, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 10 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender