Tender For Civil Works For Dairy Automation Plant At Madurai Dairy, Madurai Union
Tender Value
2.94 Crore
Estimated cost
Bid Submission
12 Aug 2026
16 days left
EMD
2.82 Lakhs
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Madurai → Tamil Nadu
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Civil Works For Dairy Automation Plant At Madurai Dairy, Madurai Union
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling RCC and clearing the debris away etc., complete as directed by the Federation Officers and as per standard specifications |
| 2 | EARTHWORK EXCAVATION for all soils and sub soils and to full depth as may be directed except in rock requiring blasting but inclusive of shoring, strutting and baling out water wherever necessary and refilling the sides of foundation with excavated earth in layers of not more than 15cm thick, well rammed and consolidated and depositing the surplus earth within the compound in places shown by the departmental officers with initial lead and lift etc., complete complying with standard specifications. (0 - 2.00 m) |
| 3 | Supplying and filling in foundation and basement and trencles with FLLING M-SAND in layers of not more than 15cm thick, well watered, rammed and consolidatedcomplying with standard specification etc., complete as directed by the departmental officers |
| 4 | Plain cement concrete 1:5:10 (one cement, five M-sand and ten course aggregate) using 40mm size granite broken stones for foundation including dewatering if found necessary and laid in layers of not more than 15cm Tk for flooring including, rendering the top surface rough to take floor finishetc and including side shuttering if required and compaction curing etc., complete and as per standard specifications. |
| 5 | Providing and laying in position, standardised concrete Mix M-20 Grade by insitu machine mix concrete adopting weighing batch method in accordance with IS 456 using 20mm and down graded hard broken granite stone jelly for all RCC oitems of works with minimum cement content of 325 kg/m3 and maximum water cement ratio of 0.55, including admixture (plasticiser/super plasticiser)in recommended proportions as per IS 9103 to accelerate , retard setting of concrete , improve workability without imparing strength and durability with about (5 cu.m) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m) 5156 kh of 10-12mm machine crushed stone jelly and with about (4.79cum) 7670kg. of crushed stone sand, but excluding cost of centering and shuttering and also including laying , vibratingwith mechanical vibrators, finishing, curing etc anf providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without standard specification and as directed by the departmental officers. The course and fine aggregates to be used should comply with the requiremenmts of IS standards.(No seperate payment will be made by the Department for the excess usage of materials)Upto basement |
| 6 | Above basement |
| 7 | Supplying fabricating and placing in position Mild Steel/ Ribbed Tor Steel reinforcement grills of all variety like HYSD/CTD/TMT and all grade like Fe 500, Fe550D, Fe 500D etc, for all RCC works as per design given including cost of steel reinforcement and G.I binding wire, wastage etc. complete complying with standard specification and as directed by the departmental officers(Contractor has to make his own arrangements for the supply of steel reinforcement wire) |
| 8 | Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced cement concrete works such as coloumn footings, coloumn pedestals, plinth beams, grade beams, staicase steps, sill slabs etc, which require only nominal strutting using mild steel sheets of size 90cm x 90cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3mm for boarding,laid with silver oak joists of size 10cm x 5cm & 7.5cm x 5cm as support runner, plain surface upto basement |
| 9 | 0 to 3.30m (plain surface) |
| 10 | Supplying and erecting steel centering including necessary supports for plane surfaces such as rectangular or square RCC coloumns. Which require only nominal strutting using mild steel sheets made of 10 gauge RCC columns etc., which require only nominal strutting using mild steel sheets made of 10 gauge thick welded with MS angle size |
| 11 | Supplying and filling with conveyed Gravel from approved source of supply for foundation and basement to required thickness and in layers on not more than 30 cm thick, watered ,well rammed and consolidated etc., complete as directed by the Federation officers and as per the technical Specifications. |
| 12 | Brick work in following 1:5 Cement Mortar using best quality of second class ground moulded chamber burnt bricks of size 9\\" x 4 1/2x3 for foundation and basement including curing, etc., complete complying with standard specifiction.Upto basement |
| 13 | Above basement |
| 14 | Plastering with cement mortar (1:5),12 mm thick in all floors including cost and conveyance of all materilas to site and labour charges etc,complete as per standard specifications. |
| 15 | Plastering the ceiling with cement mortar (1:3)12 mm ,thick in all floors including cost and conveyance of all materils to site and labour charges etc,complete as per standard specifications |
| 16 | Painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint of first class quality and of approved colour over a priming cost including through scarapping, clean removal of dirt, and including necessary plaster of paris putty, whereever required etc., complete complying with standard specification. |
| 17 | Supplying and fixing of MS Roofing sheet of 0.47mm thick with necessary GI & J bolt nut, wasers,etc, complete with standard specifications. |
| 18 | Supplying, fabricating and erection of MS Trusses complying with standard specifications including anchor and connection bolt as specified in the welding as per IS 816, of approved quality and colour after sand blasting with necessary hire charges of crane, hoisting,equipments, rope charges, painting etc, complete in all respects as directed by the federation officers. |
| 19 | Providing and filling epoxy grouting for old granite stone joints 2-4mm width,10-15mm depth) with approved make two component epoxy resin grout including raking out existing loose mortar, cleaning joints with air blower, removing dust and debris, mixing epoxy resin and harderer in proper proportion, filling |
| 20 | Supplying fabrication and erection of 65mm dia GI pipe 'B' class of approved quality and ISI make including bracing the pipe inside to a depth of 1 m , below G.L and bed level upto landing 2m (ave) and above landing upto roof 2.7m on one side and 3.00 m on another side of existing office cabin, welded with M.S Plate of size 0.15m x 0.15m x 6mm at landing level as base plate fixed with necessary bolt, nut etc., complete |
| 21 | Supply and fixing in position with 50mm thick PU(polyurethane) PUF insulated sandwich panel roofing sheet of 40mm to 50mm prepainted Galvanum corrugated of approved make for roofing, cantilevered canopies the rate including the laps with necessary langing soffits with anchor fasteners, GI , Y bolts, nuts,screws,bitumen washers etc., complete as directed by the departmental officers and as per specification.(The material should get approved from the AEE) |
| 22 | Supplying and laying of Interlocking Paver Block Stone 83mm thick Over a baselayer of sand filling incl. cost of materials laying and Labour charges etc., complete as directed by the federation officers and as per standard specification. |
| 23 | Paving the floor with Granite stone slabs of 30mm thick with machine cut edges of size 2'0\\" x 2'0\\" and above (un-polished) in all floors laid in of cement mortar 1:3 (one cement three sand), 20mm thick and pointed with colour cement neatly including polishing with polishing stone and oxalic acid etc.,so as to perfectly smooth and glossy and including hire charges for polishing machine and power consumption charges etc. The stone slabs and other materials to be used shall be got approved by the Asst Executive Engineer concerned before use on work, etc |
| 24 | Clearing jungles using earth movers machinery etc., complying with standard specifications |
| 25 | Supply and fixing Solar Reflective Tiles of size 305mm x 305mm x 6mm thick laid in CM 1:3, 30mm thick including cost of providing with white cement / colouring pigment etc.,complying with standard specification |
| 26 | Paving the floor with best quality vitrified Tiles of following size and variety conforming IS 15622 with water absorption less than 0.08% of approved colour and shade laid over cement mortar bed of 20mm thick in cement mortar 1:3 (one cement and three crushed stone sand) with required cement slurry and Mortar plasticizer in all floors and the top pointed with water resistant with water resistant tile epoxy Grout etc., complete complying with standard specification and as directed by the departmental officers, (The make and brand of the Tiles should be got approved by Executive Engineer before use on works) |
| 27 | Fabricating Supplying and fixing in positionof Aluminium anodised natural colour matt finiah of single leaf door with half panelled with 12mm thick both side laminated particle board at bottom and half glazed using 5.50mm thick plain glass at top. Rhe outer frame shall be with aluminium box section 101.60 x 44.45 x 3.18m at 2.319kg/m and Shutter frame made of section vertical and top rail: 50 x 4445 x 2.5mm @ 1.292kg/m, Alu Clips :17.15 x 17.27 x 1.50mm @ 0.176 kg/m, Alu. Handle: 100 x 30mm @ 0.988 kg/m and necessary accessories such as aluminium clips,rubber beading, PVC felt, handle for a length of shutter (both sides), locking arrangements, furniture fittings such as aluminium tower bolts - 250 x 12mm - 1 No.,aluminium tower bolt 200 x 12mm -1 No., aluminium Hydraulic door closer- 1No., lock- 1No., Door stopper with rubber bush including cost of materials labour charges etc., complete. All the Alu. Section are to be anodised with matt finish under electicaly controlled conditions in accordance with IS 1868/1962 for an average anatic film thickness of 15 microns, and furniture fittings shall be got approved by the Asst. Executive Engineer incharge. |
| 28 | Wiring with 2 x 1.5sq.mm (22 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories and with TW switch box and 5A FT switch with painting of suitable colour for open PVC light point/ fan point(for electronic regulator)(6 points per coil) SD -20 |
| 29 | Supply and fixing of 20W 4 feet LED fitting with LED etc., complying with standard specification. |
| 30 | Supply and fixing of AC Ceiling Fan Complete 1400mm (56\\") sweep with 300mm Down Rod etc., complying with standard specification. |
| 31 | Supply and fixing of PVC 110mm dia rain water down fall pipe including all material, labour, transport charges etc., complete as directed by the federation officers and as per standard specification. |
| 32 | Supply and installation of two -track sliding Upvc windows with integrated fly mesh shall utilize UPVC profile sections with an outer wall thickness of 2.30mm (+-0.2mm),featuring an outer frame of 92mm x 52mm x 52mm , a shutter of 66mm x 42mm , and a fly mesh shutter of 66mm x 30mm. All profiles of frames , sash, and mullion shall be reinforced , where required, with 1mm thick GI steel sections. Each window will be equipped with various security devices , such as touch locks or cresant locks,along with nylon rollers and an aluminium track for smooth operation, all supplied as per requirements, complaint with relevant specifications, and as directed by departmental personnel. The windows shall incorporate 5mm thick plain or pinhead glass , held securely by TPE (Grey) mitred cut and fusion welded without any mechanical joints of the frame and sash are to be mitred cut and fusion welded without any mechanical joints, with all welded joints neatly trimmed and finished with a grooved nib to ensure the final products are free from sharp edges. The complete window units shall br fixed into prefinished openings by drilling and fastening through the outer frame using high-quality fasteners, and silicon sealant will be applied to fill the gap between the wall and window frame for a leak -proof installation and complete finish etc., complete and as directed by the departmental officers. |
| 33 | Removing existing gi sheet in tanker reception for area of 120sqm and stacking inside dairy premises etc complete with standard specifications. |
| 34 | Supply and fixing of amul trap Larger SS Grating/ Drainage (2' x 2'): For larger 2ft x 2 ft stainless steel gratings, industrial,or heavy duty drainage systems including civil works etc complete with standard specifications. |
| 35 | Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification and as directed by the departmental officers. (The make , quality and colour of paint should be got approved by the Executive Engineer before use on works) |
| 36 | GST (Note: The tenderer should quote the amount towards Goods and Service tax (GST) in the appropriate columns in terms of percentage (%). If not quoted, it will be considered that the rate quoted is inclusive of GST.) Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 25, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 12, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 16 daysAug 12, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 16 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender