Tender For Upgradation Of Microbiology Laboratory In The Department Of Pharmaceutical Sciences At Main C Us, University Of Kashmir (Advertised Cost Rs. 2.83 Lac)
Tender Value
2.83 Lakhs
Estimated cost
Bid Submission
03 Aug 2026
2 days left
EMD
5660
Bank guarantee accepted
Document Fee
200
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Srinagar → Jammu and Kashmir
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Upgradation Of Microbiology Laboratory In The Department Of Pharmaceutical Sciences At Main C Us, University Of Kashmir (Advertised Cost Rs. 2.83 Lac)
BOQ
| Sl. No. | Item Description |
| 1 | Providing and fabrication of Storage cabinets (under/ above counter) of approved design made of 18-19mm Ply sheet (Ply to Ply) in sides, shelves wherever required in desired color including fixing of 12mm BWP ply sheet on backside and 18-19mm ply board in shutters duly finished with Dulmica sheeting of minimum 0.5-0.8mm thick of approved quality, color & texture on all inside and outside surfaces including finished beadings, PVC tappping of same color. Spacing of 18-19mm ply shelves to be approx 1' or as per the drawings of EICAlmirah's to be duly fixed to floor, wall and ceiling with dash fasteners and supports. Job also includes cost of fittings like handle, piano hinges, 5mm glass, channels, locks and catcher etc if required as per the approved drawings of EIC (For payments Front face to be measured) |
| 2 | 30 cm deep |
| 3 | 40-50 cm deep |
| 4 | 60-75 cm deep |
| 5 | Aluminium Work Providing and fixing Aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia. and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminum sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminum snap beading for glazing / paneling, C.P. brass / stainless steel screws,dashfastners, handles, hinges, locks all complete as per architectural drawings and the directions of Engineer-in-charge. (including 12mm thick prelaminated particle board/ Glazing, with 5mm float glass sliding channels/ sliding arrangement and other fittings complete)Powder coated aluminum (minimum thickness of powder coating 50 micron)Using 4\\"x1.75\\" in partitions and 2.5\\"x1.50\\" in door/window sections |
| 6 | Providing and fixing Tiled/GRID false ceiling of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 grams/ sqm, both side inclusive) consisting of main “T” runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross “T” of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main “T” at 600 mm center to center to form a grid of 1200x600 mm and secondary cross “T” of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc.(Global white/ Off white colour tiles of size 595x595 mm, and 0.5 mm thick with 8mm drop; made of G.I sheet having galvanizing of 100 gms/ sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending) Cost is inclusive of dismentling of old ply, ceiling |
| 7 | Removing and Refixing of old door shutters including cost of hinges, tower bolts and other fittings as per dierections of EIC |
| 8 | Demolishing brick work in cement mortar up to floor V level including stacking of serviceable material and disposal of unserviceable material within the campus as per directions of EIC. |
| 9 | Brick work with FPS bricks of class designation 75 in super structure up to all floors.In cement mortar 1cement: 6 fine sand mortar. |
| 10 | Providing and fixing 30-35 mm thick wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4mm with wire of dia. 0.63 mm for doors, windows and clerestory windows including ISI marked bright finished or / and black enameled M.S. butt hinges with necessary screws and fittings like handles and tower bolt First. Class imported wood. |
| 11 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid separately)1st Class imported wood. |
| 12 | Providing 40x5mm flat Iron hold fast 40 cm long including fixing of frame with 10mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15 cm 1:3:6 mix (1cement: 3 coarse sand: 6 graded stone aggregate 20mm nominal size) |
| 13 | 12mm thick cement plaster on half brick / concrete wall of mix 1:6 (1cement: 6 coarse sand) |
| 14 | Wall painting with plastic emulsion paint (one or more coats) of approved brand and manufacture to give an even shade. Old work |
| 15 | Providing and applying cement based wall putty of 1mm thickness over plastered surface to prepare the surface even and smooth complete |
| 16 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade two or more coats on new wood work/ plastered surface including sand papering, knotting and coat of primer complete wherever required |
| 17 | Providing and fixing of aluminum double channel with wheel set for sliding glass window of approved quality of following sizes.25mm |
| 18 | Providing and fixing of glass pans with wooden fillets of required size wherever necessary. Glass pans 5mm thick weighing 13.75 Kg/ sqm Please Enable Macros to View BoQ information |
| 19 | Providing and fixing of glass pans with wooden fillets of required size wherever necessary. Glass pans 5mm thick weighing 13.75 Kg/ sqm Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 25, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 03, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 2 daysAug 04, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 3 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender