Tender For Repair / Replacement Of Roofing / Ceiling, And Allied Minor Works Of Crpf Barrack No.G/77 Bn. Situated At Atlanta Point Under Sd-I,Svpsd,Apwd.
Tender Value
6.41 Lakhs
Estimated cost
Bid Submission
31 Jul 2026
0 days left
EMD
12835
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
South Andamans → Andaman And Nicobar Islands
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repair / Replacement Of Roofing / Ceiling, And Allied Minor Works Of Crpf Barrack No.G/77 Bn. Situated At Atlanta Point Under Sd-I,Svpsd,Apwd.
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within 50 metres lead of: |
| 2 | G.S. Sheet |
| 3 | Dismantling wood work in frames, trusses, purlins and rafters up to 10 metres span and 5 metres height including stacking the material within 50 metres lead : |
| 4 | Of sectional area 40 square centimetres and above |
| 5 | Dismantling cement asbestos or other hard board ceiling or partition walls including stacking of serviceable materials and disposal of unserviceable materials within 50 metres lead. |
| 6 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-Charge) of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05mm) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 7 | Providing and fixing precoated galvanised steel sheet roofing accessories of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05 mm) with Zinc coating 120 gram per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : |
| 8 | Ridges plain (500- 600mm) |
| 9 | Providing and fixing plain multipurpose cement board(Hight pressure steam cured) with suitable screws for cement particle board in ceiling etc. complete (frame work to be paid seperatately). |
| 10 | 6 mm thick Cement fiber board, Type-B, Category-III as per IS: 14862 :2000 |
| 11 | 12 mm cement plaster of mix: |
| 12 | 1:4(1 cement: 4 fine sand) |
| 13 | Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge. |
| 14 | With cement mortar 1:4 (1 cement : 4 fine sand) |
| 15 | Applying priming coat: |
| 16 | With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works |
| 17 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade: |
| 18 | One or more coats on old work |
| 19 | Distempering with 1st quality acrylic distemper (ready mixed) having VOC (Volatile Organic Compound ) content less than 50 gram/ litre, of approved brand and manufacturer including applying additional coats wherever required to achieve even shade and colour |
| 20 | Old work (one or more coats) |
| 21 | Providing and laying hollow cement concrete block walling upto floor five level 100mm thick consisting of hollow block of size 400x100x200mm of mix 1:3:6(1 :cement 3 :coarse sand 6 :graded stone aggregate 10mm nominal and down size) having a crushing strength of 3.5N/sqmm at 28 days as per IS:2185 (part-I) 1979 laid in cement mortar 1:6(1 :cement 6 :coarse sand) upto floor five level. |
| 22 | Providing wood work in frames of false ceiling, partitions etc. sawn and fixed in position : |
| 23 | a) Superior Hard wood Cat-II (A) |
| 24 | Demolishing brick / hollow block work manually / by mechanical means including stacking of servoable materials and disposal of unserviceable materials within 50 metres lead as per the Diotection of Engineer-In-Charge.In Cement Mortar |
| 25 | Providing and fixing in position facias and eaves board with precoated galvanized steel sheet of 0.50mm (+ 0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns 30cm wide including fixing witth nuts and bolts etc. complete : |
| 26 | Providing wood work in frames, trusses, purlins, rafters, etc. sawn and put up in position. a) Second Class Hard Wood Cat-II (B) |
| 27 | Dismantling eaves of facia board of 19mm thick ply wood including stacking within 50merers lead. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 24, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 31, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedJul 31, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender