Tender For Maintenance Work Of Upper And Lower Zone Building Of Housing Board At Santhinagar Thiruvananthapuram Civil And Electrical Works Phase 1
Tender Value
Ref. Documents
Estimated cost
Bid Submission
11 Aug 2026
17 days left
EMD
2 Lakhs
Bank guarantee accepted
Document Fee
13010
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Thiruvananthapuram → Kerala
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Maintenance Work Of Upper And Lower Zone Building Of Housing Board At Santhinagar Thiruvananthapuram Civil And Electrical Works Phase 1
BOQ
| Sl. No. | Item Description |
| 1 | Wall paneling and its frame work |
| 2 | 50.10.2:Steel work for purlin/single section with G I pipes including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete |
| 3 | 13.61.1:Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:Two or more coats on new work |
| 4 | OD84622/2026-2027:Providing and fixing wall panelling with 7.5 mm thick PVC plain panel board of approved quality in aluminium frame work with necessary screws etc complete (aluminium frame work shall be paid separately) |
| 5 | 50.4.1.1:Providing and laying in position cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 12.5 mm nominal size) up to floor five level excluding the cost of centering, shuttering, finishing for leveling coarse of floor and roof etc. |
| 6 | 13.9.2:Cement plaster 1:3 ( 1 cement : 3 coarse sand) finished with a floating coat of neat cement.20 mm cement plaster |
| 7 | Demolishing works |
| 8 | 15.12.1:Dismantling doors, windows and clerestory windows (steel or wood ) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead:Of area 3 sq. metres and below |
| 9 | 15.12.2:Dismantling doors, windows and clerestory windows (steel or wood ) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead:Of area beyond 3 sq. metres |
| 10 | 14.2.2:Fixing chowkhats in existing opening including embedding chowkhats in floors or walls cutting masonry for holdfasts, embedding hold fasts in cement concrete blocks of size 15 x 10 x 10 cm with cement concrete 1:3:6 (1 cement: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size), painting two coats of approved wood preservative to sides of chowkhats and making good the damages to walls and floors as required complete, including disposal ofrubbish to the dumping ground, all complete as per direction of Engineer-in-Charge.Window chowkhats |
| 11 | 15.7.4:Demolishing brick work manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-Charge.In cement mortar |
| 12 | 15.23.1:Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.For thickness of tiles 10 mm to 25 mm |
| 13 | 15.52:Dismantling of flushing cistern of all types (C.I. / PVC/ Vitrious China) including stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead |
| 14 | 15.57:Dismantling aluminium / Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material and stacking of serviceable material with in 50 metres lead as directed by Engineer - in-Charge |
| 15 | 15.60:Disposal of building rubbish/ malba/ similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved |
| 16 | False ceiling,Tiling works in Common area , Lobby including concreting |
| 17 | 12.53:Providing and Fixing 15 mm thick densified tegular edged eco friendly lightweight calcium silicate false ceiling tiles of approved texture of size 595 x 595mm in true horizontal level, suspended on inter locking metal grid of hot dippedgalvanised steel sections (galvanising @ 120 grams per sqm including bothside) consisting of main ‘T’ runner suitably spaced at joints to get requiredlength and of size 24x38 mm made from 0.33 mm thick (minimum) sheet, spaced1200 mm centre to centre, and cross “T” of size 24x28 mm made out of 0.33 mm(Minimum) sheet, 1200 mm long spaced between main’T’ at 600 mm centre tocentre to form a grid of 1200x600 mm and secondary cross ‘T’ of length 600 mmand size 24 x28 mm made of 0.33 mm thick (Minimum) sheet to be inter locked atmiddle of the 1200x 600 mm panel to from grid of size 600x600 mm, resting onperiphery walls /partitions on a Perimeter wall angle pre-coated steel ofsize(24x24X3000 mm made of 0.40 mm thick (minimum) sheet with the help ofrawl plugs at 450 mm centre to centre with 25 mm long dry wall screws @ 230mm interval and laying 15 mm thick densified edges calicum silicate ceilingtiles of approved texture in the grid, including, cutting/ making opening forservices like diffusers, grills, light fittings, fixtures, smoke detectors etc.,wherever required. Main ‘T’ runners to be suspended from ceiling using G.I.slotted cleats of size 25x35x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mmlong dash fasteners, 4 mm G.I. adjustable rods with galvanised steel level clipsof size 85 x 30 x 0.8 mm, spaced at 1200 mm centre to centre along main ‘T’,bottom exposed with 24 mm of all Tsections shall be pre-painted with polysterbaked paint, for all heights, as per specifications, drawings and as directed byEngineer-in-Charge. |
| 18 | 11.56.1:Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent |
| 19 | 8.3.2:Providing edge moulding to 18 mm thick marble stone counters, vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer -in-Charge.Granite work |
| 20 | OD70738/2026-2027:Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS : 15622, of approved brand & manufacturer,in all colours and shade, in walls, skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately).Size of Tile 1200 x 600 mm |
| 21 | OD70741/2026-2027:Providing and laying Matt finish Glazed Vitrified tiles in floor with different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS : 15622, of approved brand & manufacturer, in all colours and shade, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately).Size of Tiles 600 x 1200 mm |
| 22 | OD70739/2026-2027:Cleaning existing mosaic flooring using approved diluted acid solution, scrubbing with rotarymachine/manual brush, removing stains, washing with clean water, neutralising surface anddisposing debris complete, including dismantling and repairing damaged / hollow / brokenportions of existing mosaic flooring near wall junctions or wherever required, using cementmortar/terrazzo mix to match existing flooring, curing, rubbing and finishing the repairedportions to proper level and alignment, complete as directed by Engineer-in-charge. |
| 23 | OD70740/2026-2027:Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg). including filling /grouting and finishing complete as per direction of Engineer-in-charge.Size of Tile 600x600 mm or 600 x 1200 |
| 24 | 5.9.5:Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers |
| 25 | 4.1.3:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand (zone-III)derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 26 | 4.1.8:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 27 | 13.1.1:12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand) |
| 28 | Stair case |
| 29 | 13.114:Melamine polishing on wood work (one or more coat). |
| 30 | 13.99.1:Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :One or more coats on old work |
| 31 | Doors and Fittings |
| 32 | 9.147B.1:Providing and fixing factory made uPVC white colour fixed glazed windows/Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm.) |
| 33 | OD70710/2026-2027:Providing and fixing WPC Sliding Bathroom Door comprising 30 mm thick WPC shutter of density 0.70±, Century WPC sliding channel, rollers, guide, stopper, lock, handle, screws and 38×50 mm (1½"×2") Century WPC frame complete. |
| 34 | 26.86.1:Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Ceosetory windows & other Frames/Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/ mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.Frame size 45 x 70 mm |
| 35 | 26.87.1:Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-InCharge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) 30 mm thick |
| 36 | 9.147C.2:Providing and fixing factory made uPVC white colour casement/ Casement cumfixed glazed door comprising of uPVC multi-chambered frame, sash and mullion(where ever required) extruded profiles duly reinforced with 1.60 +/- 0.2 mm thickgalvanized mild steel section made from roll forming process of required length(shape & size according to uPVC profile), uPVC extruded glazing beads ofappropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hingesand one handle on each side of panels along with zinc plated mild steel multipoint locking having transmission gear, cylinder with keeps and one side key,G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessarystainless steel screws, etc. Profile of frame & sash shall be mitred cut and fusionwelded at all corners, mullion (if required) shall be also fusion welded includingdrilling of holes for fixing hardware's and drainage of water etc. After fixingframe the gap between frame and adjacent finished wall shall be filled withweather proof silicon sealent over backer rod of required size and of approvedquality, all complete as per approved drawing & direction of Engineer-in-Charge.(Single / double glass panes and silicon sealent shall be paid separately).Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerancein dimension i.e. in depth & width of profile shall be acceptable.Casement door with top hung ventilator with 3D and S.S. friction hinges (400 x 19 x 1.9 mm) made of (big series) frame 67 x 64 mm, sash 67 x 110 mm & mullion 67 x 80 mm all having wall thickness of 2.3 +/- 0.2 mm and single glazing bead / double glazing bead of appropriate dimension.(Area of door upto 2.50 sqm) |
| 37 | OD70713/2026-2027:Providing and fixing glazing in UPVC door with EPDM rubber/neoprene gasket etc. complete as per architectural drawings and directions of Engineer-in-Charge (Cost of UPVC door frames and shutters shall be paid separately): With toughened glass panes of 8.0 mm thickness |
| 38 | OD70869/2026-2027:Providing and fixing factory made uPVC Casement Door with full panelling made from approved equivalent, white colour, 2.25 mm wall thickness, multi-chambered section with galvanized steel reinforcement, outer frame size 60×74 mm, shutter sash size 86×60 mm, double glazing bead, EPDM gasket, 3 nos SS hinges, multipoint locking system, handle, screws and fasteners complete. The shutter shall be infilled with 19 mm thick uPVC panel. Complete as per manufacturer's specification and direction of Engineer-in-Charge. |
| 39 | 10.6.2:Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters.80x1.20 mm M.S. laths with 1.20 mm thick top cover |
| 40 | 13.61.1:Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:Two or more coats on new work |
| 41 | OD70712/2026-2027:Supplying and fixing UPVC Louvers, Profile Colour off White 2.25MM - 2.5MM Wall Thickness with 3multi chambered sections, UV treated profiles, Tested With 600 Hours Casement frame 40x60x60mm, Casement T-Mullion 36x60x76mm, Single glaze beeding, S-louver 16x60mm, vantilator cap 20x46mm, Epdm Rubber gaskets, etc/- |
| 42 | 9.71.2:Providing and fixing IS : 12817 marked stainless steel butt hinges (heavy weight) with stainless steel screws etc. complete:100x60x2.50 mm |
| 43 | 9.88:Providing and fixing chromium plated brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete. |
| 44 | 14.6.1:Renewing glass panes, with wooden fillets wherever necessary: Float glass panes of nominal thickness 4 mm (weight not less than 10kg/sqm) |
| 45 | 21.3.1:Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm) |
| 46 | 9.12:Extra for providing frosted glass panes 4 mm thick (weight not less than 10 kgper sqm) instead of ordinary float glass panes 4 mm thick (weight not less than10 kg per sqm) in doors, windows and clerestory window shutters. (Area ofopening for glass panes excluding portion inside rebate shall be measured). |
| 47 | Truss work and Roofing sheet |
| 48 | 50.10.1:Steel work in built up G I tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting,fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete |
| 49 | 50.10.2:Steel work for purlin/single section with G I pipes including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete |
| 50 | 12.50:Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+0.05%), total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 51 | 50.12.2.1:Providing & fixing Poly carbonate corrugated sheet 0.8 mm thick as approved by the Engineer in charge and should be supplied in a single length of 12 M or as decide by the Engineer in charge. The sheets shall be fixed using self drilling / self tapping screw of size (5.5x55 mm) with EPDM seal complete upto any pitch in horizontal/ vertical/ curved surface, but excluding the cost of purlins, rafters, trusses, and including cutting to size shapes where ever required. |
| 52 | OD70707/2026-2027:Providing and fixing 1.5 mm thick GI perforated sheet having 6 mm diameter perforations of approved pattern and spacing, fixed to GI/MS sub-frame with SS self-drilling screws, bolts, cleats and accessories complete, including cutting, bending, fabrication, erection and finishing, as directed by Engineer-in-Charge. |
| 53 | OD70709/2026-2027:Providing and fixing 4 mm thick Aluminium Composite Panel (ACP) cladding with FR grade core and 0.5 mm aluminium skin on both sides including cutting, grooving, bending, tray formation and fixing with SS screws, cleats, silicone sealant etc. complete.(Framework paid separately) |
| 54 | OD70708/2026-2027:Providing and fixing 220 mm (8 inch) uPVC Square Gutter / Pathy with necessary brackets, couplers, end caps, outlet nozzles, screws and sealant complete as directed by Engineer-in-Charge. |
| 55 | 12.43.2:Providing and fixing unplasticised- PVC pipe clips of approved design to unplasticised- PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 ( 1 cement : 4 coarse sand) and making good the wall etc. complete.110 mm |
| 56 | 13.61.1:Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:Two or more coats on new work |
| 57 | Connecting bridge |
| 58 | 50.10.2:Steel work for purlin/single section with G I pipes including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete |
| 59 | 10.1:Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 60 | 13.61.1:Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:Two or more coats on new work |
| 61 | Construction of new toilet |
| 62 | Construction of chamber for 100mm sluices valve |
| 63 | Construction of chamber for 100mm sluices valve |
| 64 | Construction of chamber for 100mm sluices valve |
| 65 | Plain Cement Concrete 1:4:8 (one cement four fine aggregates and eight coarse aggregates) using |
| 66 | Brick work in C.M 1:5 mix using 2nd class ground moulded chamber burnt bricks with including cost |
| 67 | Construction of chamber for 100mm sluices valve |
| 68 | Construction of chamber for 100mm sluices valve |
| 69 | Plain Cement Concrete 1:4:8 (one cement four fine aggregates and eight coarse aggregates) using |
| 70 | Brick work in C.M 1:5 mix using 2nd class ground moulded chamber burnt bricks with including cost |
| 71 | Construction of chamber for 100mm sluices valve |
| 72 | Plain Cement Concrete 1:4:8 (one cement four fine aggregates and eight coarse aggregates) using |
| 73 | Brick work in C.M 1:5 mix using 2nd class ground moulded chamber burnt bricks with including cost |
| 74 | Construction of chamber for 100mm sluices valve |
| 75 | Construction of chamber for 100mm sluices valve |
| 76 | Construction of chamber for 100mm sluices valve |
| 77 | Plain Cement Concrete 1:4:8 (one cement four fine aggregates and eight coarse aggregates) using |
| 78 | Sanitary installations |
| 79 | 17.2.1:Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:W.C. pan with ISI marked white solid plastic seat and lid |
| 80 | 17.78:Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/6 litre (adjustable to 4 litre /8 litres), including seat cover, and cistern fittings, nuts bolts and gasket etc complete. |
| 81 | 50.17.1.4:Supplying and fixing CP Health faucet good quality including cost of materials and labour charges etc. complete as per the direction of site engineer-in-charge. |
| 82 | OD70717/2026-2027:Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with standard flush pipe and C.P. brass spreaders with brass unions and G.I. clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required:One urinal basin |
| 83 | 17.7.5:Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Angle back wash basin size 600x480 mm with single 15 mm C.P. brass pillar tap |
| 84 | 18.53.1:Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS: 893115 mm nominal bore |
| 85 | 18.21.2.1:Providing and fixing uplasticised PVC connection pipe with brass unions:45 cm length15 mm nominal bore |
| 86 | 17.31:Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 87 | 17.28.2.1:Flexible pipe32 mm dia |
| 88 | OD70716/2026-2027:Providing and fixing L-shaped stationary grab bar of stainless steel, having satin/matt finish, suitable for accessible/disabled toilet, including wall fixing flange, stainless steel anchor fasteners, drilling holes in wall, fixing, testing and making good damaged surfaces complete as directed by Engineer-in-Charge. |
| 89 | OD70721/2026-2027:Providing and fixing U-shaped movable/folding grab bar made of stainless steel wall mounted with hinged/folding mechanism, suitable for accessible/disabled toilets, including stainless steel mounting plate, anchor fasteners, drilling holes in wall, fixing, testing, all labour, T&P, consumables and making good the damaged surface complete as directed by Engineer-in-Charge. |
| 90 | 18.58.1.1:Providing and fixing PTMT grating of approved quality and colour.Circular type100 mm nominal dia |
| 91 | OD70719/2026-2027:Providing and making 50 mm diameter core cutting in RCC slab/wall using a diamond core cutting machine, including marking, drilling, removal of concrete core, disposal of debris, and making good the surface complete as directed by the Engineer-in-Charge. |
| 92 | OD70718/2026-2027:Providing and making 100 mm diameter core cutting through RCC roof slab/wall using diamond core cutting machine, including marking, drilling, removal of concrete core, disposal of debris and making good the damaged surface complete. |
| 93 | OD70800/2026-2027:Providing and making 75 mm diameter core cutting in RCC slab/wall using a diamond core cutting machine, including marking, drilling, removal of concrete core, disposal of debris, and making good the surface complete as directed by the Engineer-in-Charge. |
| 94 | 17.60.1.1:Providing and fixing trap of self cleansing design with screwed down or hinged grating without vent arm complete, including cost of cutting and making good the walls and floors:100 mm inlet and 100 mm outletSand cast iron S & S as per IS : 3989 |
| 95 | 50.17.1.1:Supplying and fixing Stainless steel soap dish including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge. |
| 96 | 50.17.1.2:Supplying and fixing CP Towel rod 45cm or nearest available length including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge. |
| 97 | Plumbing works for Water supply |
| 98 | 50.18.8.2.2:Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 20 mm pipe 10 Kgf/ cm2 |
| 99 | 50.18.8.3.2:Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 25 mm pipe 10kgf /cm2 |
| 100 | 50.18.8.4.2:Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 32 mm pipe 6Kgf/cm2 |
| 101 | 50.18.9.14.2:Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 32 mm dia 6 Kgf/cm2 - External work - Exposed on wall |
| 102 | 50.18.9.15.2:Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 40 mm dia 6 Kgf/cm2 - External work - Exposed on wall |
| 103 | 50.18.9.16.2:Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 50 mm dia 6Kgf/cm2 - External work - Exposed on wall |
| 104 | 50.18.9.17.1:Providing and fixing PVC pipes including fixing the pipe with clamps/ clip at 1.00 m spacing . This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 63 mm dia 6 Kgf/cm2 - External work - Exposed on wall |
| 105 | 50.18.9.6.1:Providing and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 50 mm dia 10Kgf/cm2 |
| 106 | 50.18.9.20.1:Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 63 mm dia Elbow |
| 107 | 50.18.9.20.10:Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 63x50 mm dia Reducer |
| 108 | 50.18.9.20.4:Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 63 mm dia Bend |
| 109 | 50.18.9.20.9:Providing and fixing PVC moulded fitting / accessories for Rigid PVC pipes, including jointing with PVC solvent cement-63 mm dia Socket /coupling |
| 110 | OD100826/2026-2027:Providing and fixing 50 mm dia full bore brass ball valve (PN-16), screwed ends, with PTFE seats, SS/Chrome plated brass ball, complete with cutting, threading, jointing using PTFE tape/hemp, testing and commissioning. |
| 111 | OD100827/2026-2027:Providing and fixing brass ball valve of approved quality with threaded ends, complete with all fittings, testing and commissioning, suitable for water supply lines, including cutting and making good the pipe connections, complete as required.Size: 32 mm |
| 112 | OD100828/2026-2027:Supplying, fixing, testing and commissioning of Manual Butterfly Valve with Cast Iron (CI) body, Stainless Steel (SS) disc, Nitrile rubber seat & O-ring, PN-16 pressure rating, 65 mm dia., complete as specified. |
| 113 | OD100829/2026-2027:Providing and fixing 150 × 150 mm Chrome Plated Brass Clean Out with Stainless Steel (Grade 304) Cover complete with threaded brass plug, SS screws, rubber gasket, cutting, making good, testing and commissioning. |
| 114 | Plumbing works for Drainage and rain water |
| 115 | 50.18.7.6.1:Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 50 mm dia 10 Kfg/cm - Internal work- Exposed on wall |
| 116 | 50.18.9.18.1:Providing and fixing PVC pipes including fixing the pipe with clamps/clips at 1.00 m spacing. This included jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 75 mm dia 6Kgf/cm2 - External work- Exposed on wall |
| 117 | 50.18.9.19.1:Providing and fixing PVC pipes including fixing the pipe with clamps/ clips/ at 1.00 m spacing . This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 110 mm dia 6 Kgf/cm2 - External work- Exposed on wall |
| 118 | 50.18.9.9.1:Providing and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement, trenching, refilling & testing of Joints complete as per direction of engineer in charge.110 mm dia 6Kgf/cm2 |
| 119 | 50.18.9.21:Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 75 mm dia Elbow |
| 120 | 50.18.9.21.2:Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes, including jointing with PVC solvent cement -75 mm dia 45 degree Elbow |
| 121 | 50.18.9.21.4:Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 75 mm dia Bend |
| 122 | 50.18.9.21.5:Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement -75x75x75 mm dia Tee |
| 123 | 50.18.9.21.7:Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 75 mm dia Vent cowl |
| 124 | 50.18.9.22.1:Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110 mm dia Elbow |
| 125 | 50.18.9.22.12:Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110x75 mm dia Reducer |
| 126 | 50.18.9.22.2:Providing and fixing PVC moulded fittings / accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110 mm dia 45 degree Elbow |
| 127 | 50.18.9.22.3:Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement-110 mm dia Door Elbow |
| 128 | 50.18.9.22.4:Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement- 110 mm dia Bend |
| 129 | 50.18.9.22.5:Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes including jointing with PVC solvent cement 110x110x110 mm dia Tee |
| 130 | 50.18.9.22.7:Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110x110x75 mm dia Door Tee |
| 131 | 50.18.9.22.8:Providing and fixing PVC moulded fittings /accessories for Rigid PVC pipes, including jointing with PVC solvent cement -110 mm dia Vent cowl |
| 132 | OD70803/2026-2027:Cleaning and removing silt, sludge and rubbish from existing sewer manhole, including lifting out deposited material, disposal within 50 m lead, washing and making the manhole clean complete as directed by Engineer-in-Charge. |
| 133 | PANEL BOARD |
| 134 | OD70748/2026-2027:Fabrication, supply, conveyance, installation, testing, and commissioning of floor-mounted, dust-proof and vermin-proof cubicle type LT Main Distribution Panel Board conforming to IS 8623, fabricated using 1.6 mm thick CRCA sheet steel for covers and partitions and 2.0 mm thick CRCA sheet steel for structural members, complete with front access, compartmentalized construction, copper busbar system, separate busbar chambers, hinged and lockable doors with sealing provision for KSEB, powder coating after seven-tank treatment, 2 Nos. copper earth bars (25 mm × 3 mm) with earth studs, door earthing using braided copper conductors, danger notice board, RYB LED indication lamps, digital multifunction meter with suitable CTs, internal wiring with 6 sq.mm PVC insulated copper conductors, ferrules, glands, lugs, terminal blocks, base frame fabricated from 75 mm channel section with painting, foundation fixing, testing and commissioning, complete with the following switchgears and accessories: 1 No. 800A, 4P, 50kA ACB with microprocessor release having adjustable OL, SC & EF protection as incomer; 1 No. 320A TPN 36kA MCCB with thermal magnetic release; 3 Nos. 250A TPN 36kA MCCBs with thermal magnetic release; 3 Nos. 200A TPN 36kA MCCBs with thermal magnetic release; 2 Nos. spare chambers suitable for future installation of 250A MCCBs (without MCCBs); one set digital multifunction meter complete with CTs; one set RYB indication lamps; danger notice board and all accessories required for compliance with IE Rules, CEA Regulations, KSEB and Electrical Inspectorate requirements, complete in all respects |
| 135 | OD70743/2026-2027:Fabrication, supply, conveyance, installation, testing, and commissioning of floor-mounted, dust-proof and vermin-proof cubicle-type LT panel board conforming to IS 8623, fabricated from 1.6 mm CRCA sheet steel with 2 mm CRCA structural frame, front access type, complete with aluminium busbars, busbar chambers, hinged lockable doors with KSEB sealing provision, door earthing using braided copper conductors, powder coating after seven-tank treatment, 2 Nos. copper earth bars (25 mm × 3 mm), viewing glass for all outgoing compartments, 8 metering compartments suitable for accommodating KSEB energy meters (meter not included), base frame fabricated from 75 mm channel section, internal wiring using 6 sq.mm PVC insulated copper conductor, danger notice board, RYB LED indication lamps, testing and commissioning complete with 250A TPN MCCB incomer ? 1 No., 100A 3P MCCB outgoing feeders ? 8 Nos., 100A clay cut-out fuses ? 24 Nos., HRC 63A neutral links ? 8 Nos., and all accessories required for Electrical Inspectorate and KSEB approval, complete in all respects.(Rate should be inclusive of buy back price) |
| 136 | OD70744/2026-2027:Fabrication, supply, conveyance, installation, testing, and commissioning of floor-mounted, dust-proof and vermin-proof cubicle-type LT panel board conforming to IS 8623, fabricated from 1.6 mm CRCA sheet steel with 2 mm CRCA structural frame, front access type, complete with aluminium busbars, busbar chambers, hinged lockable doors with KSEB sealing provision, door earthing using braided copper conductors, powder coating after seven-tank treatment, 2 Nos. copper earth bars (25 mm × 3 mm), viewing glass for all outgoing compartments, 8 metering compartments suitable for accommodating KSEB energy meters (meter not included), base frame fabricated from 75 mm channel section, internal wiring using 6 sq.mm PVC insulated copper conductor, danger notice board, RYB LED indication lamps, testing and commissioning complete with 320A TPN MCCB incomer ? 1 No., 125A 3P MCCB outgoing feeders ? 2 Nos, 100A 3P MCCB outgoing feeders ? 6 Nos., 100A clay cut-out fuses ? 24 Nos., HRC 63A neutral links ? 8 Nos, and all accessories required for Electrical Inspectorate and KSEB approval, complete in all respects.(Rate should be inclusive of buy back price) |
| 137 | OD70746/2026-2027:Fabrication, supply, conveyance, installation, testing, and commissioning of floor-mounted, dust- and vermin-proof cubicle-type LT panel board conforming to IS 8623 and Electrical Inspectorate/KSEB standards, fabricated using 1.6 mm CRCA sheet steel for enclosure and 2.0 mm CRCA sheet steel for structural frame members, fully compartmentalized construction with front access, aluminium busbar system housed in separate busbar chamber, hinged and lockable doors for all compartments with KSEB sealing provision, door earthing using braided copper conductor, powder coating finish after seven-tank anti-corrosion treatment, 2 Nos. copper earth bars of size 25 mm × 3 mm mounted at the rear with earth studs, danger notice board, RYB LED phase indication lamps, digital multifunction meter with suitable CTs, internal wiring using 6 sq mm PVC insulated copper conductor cables, ferruling, lugs, glands, terminal blocks, and all accessories required for safe operation. The panel shall be mounted on a fabricated base frame made of 75 mm channel section, including cutting, welding, drilling, anti-rust priming with zinc chromate paint, and finishing with two coats of synthetic enamel paint, properly anchored to the floor with bolts and nuts, making good damages and finishing as required. The cubicle panel shall have 11 compartments suitable for accommodating single-phase energy meters (energy meters supplied by KSEB and excluded from scope), viewing glass provided for all outgoing meter doors, and shall be complete with the following switchgear and accessories: 200A, 4P MCCB incomer ? 1 No. 63A DP MCB outgoing feeders ? 12 Nos., 63A clay cut-out fuses ? 12 Nos., 63A HRC neutral links ? 12 Nos., complete as per IE Rules, CEA Regulations, KSEB standards, and Electrical Inspectorate requirements. |
| 138 | OD70742/2026-2027:Fabrication, supply, conveyance, installation, testing and commissioning of floor-mounted, dust- and vermin-proof cubicle-type LT panel board conforming to IS 8623 and Electrical Inspectorate/KSEB standards, fabricated using 1.6 mm CRCA sheet steel for enclosure and 2.0 mm CRCA sheet steel for structural frame members, fully compartmentalized construction with front access facility, copper busbar system housed in separate busbar chamber, hinged and, door earthing using braided copper conductor, powder coating finish after seven-tank anti-corrosion treatment, 2 Nos copper earth bars of size 25 mm × 3 mm mounted at rear with earth studs, danger notice board, 6 Nos LED indication lamps, 2 Nos digital multifunction meters with suitable CTs, internal wiring using 6 sq.mm PVC insulated copper conductor cables, ferruling, lugs, glands, terminal blocks and all accessories required for safe operation and compliance. The panel shall be mounted on a fabricated base frame made of 75 mm channel section, including cutting, welding, drilling, zinc chromate primer painting, and two coats of synthetic enamel paint, properly anchored to the floor with bolts and nuts, making good damages and finishing as required. The panel shall include the following switchgear: 160A, TPN, 36kA MCCB incomer (KSEB source) with thermal magnetic release and adjustable overload and short circuit protection 1 No160A, TPN, 36kA MCCB incomer (DG source) with thermal magnetic release and adjustable overload and short-circuit protection, complete with DG battery charging facility ? 1 No.160A, 4P Automatic Transfer Switch (ATS) ? 1 No.125A, 3P MCCB outgoing feeder ? 1 No.; 100A, 3P MCCB outgoing feeder 1 No.63A, 3P MCCB outgoing feeder ? 1 No.; 100A, TPN SFU 1 No.; spare chamber suitable for 100A TPN MCCB (switch not included) 1 No.; complete as per IE Rules, CEA Regulations, KSEB, and Electrical Inspectorate requirements. |
| 139 | OD70745/2026-2027:Fabrication, supply, conveyance, installation, testing and commissioning of floor-mounted, dust- and vermin-proof cubicle-type LT panel board conforming to IS 8623 and Electrical Inspectorate standards, fabricated using 1.6 mm CRCA sheet steel for enclosure and 2.0 mm CRCA sheet steel for structural frame members, fully compartmentalized construction with front access facility, aluminium busbar system rated 100A housed in separate busbar chamber, busbar insulated with heat-shrink sleeves, hinged and lockable doors for all compartments with door earthing using braided copper conductor, powder coating finish after seven-tank anti-corrosion treatment, 2 Nos copper earth bars of size 25 mm × 3 mm mounted at rear with earth studs, danger notice board, LED indication lamps, control wiring using suitable PVC insulated copper conductors, ferruling, lugs, glands, terminal blocks, selector switches, ON/OFF push buttons, voltmeter (0?500V), ammeter (0?60A) with CTs, and all accessories required for safe operation and compliance. The panel shall be mounted on a fabricated base frame made of 75 mm channel section, including cutting, welding, drilling, zinc chromate primer painting, and two coats of synthetic enamel paint, properly anchored to the floor with bolts and nuts, making good damages and finishing as required. The panel shall include the following switchgear and equipment: 40A, 4P MCCB with thermal magnetic release, 10kA breaking capacity ? 1 No.16A, TP MCB outgoing feeders ? 3 Nos.; 40A, SPN MCB ? 1 No. (KSEB supply); fully automatic star-delta starter suitable for 7.5 HP open well pump set with internal wiring and ON/OFF control ? 2 Nos.; 3 kVAR heavy-duty capacitor with MOC3 contactor ? 1 No.; complete as per IE Rules, CEA Regulations, KSEB, and Electrical Inspectorate requirements. |
| 140 | ELECTRICAL |
| 141 | 1.10.1:Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVCinsulated copper conductor single core cable in surface / recessed medium class PVC conduit,with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLSPVC insulated copper conductor single core cable etc as required.Group A |
| 142 | 1.10.3:Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVCinsulated copper conductor single core cable in surface / recessed medium class PVC conduit,with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLSPVC insulated copper conductor single core cable etc as required.Group C |
| 143 | 1.11:Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required. |
| 144 | 1.14.1:Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2x1.5 sq.mm + 1x1.5 sq.mm earth wire |
| 145 | 1.14.2:Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire |
| 146 | 1.14.3:Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2 X 4 sq. mm + 1 X 4 sq. mm earth wire |
| 147 | 1.14.4:Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2 X 6 Sq.mm + 1 x 6 sq.mm earth wire |
| 148 | 1.14.7:Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required4 X 2.5 sq. mm + 2 X 2.5 sq. mm earth wire |
| 149 | 1.14.8:Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required4 X 4 sq. mm + 2 X 4 sq. mm earth wire |
| 150 | 1.17.12:Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.3 x 2.5 sq. mm |
| 151 | 1.17.15:Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.6 x 2.5 sq. mm |
| 152 | 1.17.21:Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.3 x 4 sq. mm |
| 153 | 1.17.3:Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.3 X 1.5 sq.mm |
| 154 | 1.17.6:Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.6 x 1.5 sq. mm |
| 155 | 1.18.2:Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor,unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required.2 Pair |
| 156 | 1.21.1:Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.20 mm |
| 157 | 1.21.2:Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.25 mm |
| 158 | 1.21.3:Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.32 mm |
| 159 | 1.25:Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required. |
| 160 | 1.31:Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. (For light plugs to be used in non residential buildings). |
| 161 | 1.33:Supplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box/ wooden block including connection etc as required. |
| 162 | 1.55.1:Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.Group A |
| 163 | 1.58:Supplying and fixing PVC batten/ angle holder including connection etc. as required. |
| 164 | 2.10.1:Supplying and fixing 5A to 32 A rating, 240/415 volts, 10 kA, \\"\\"C\\"\\" curve, miniaturecircuit breaker suitable for inductive load of following poles in the existing MCBDB complete with connections, testing and commissioning etc. as required.Single pole |
| 165 | 2.10.4:Supplying and fixing 5A to 32 A rating, 240/415 volts, 10 kA, \\"\\"C\\"\\" curve, miniaturecircuit breaker suitable for inductive load of following poles in the existing MCBDB complete with connections, testing and commissioning etc. as required.Triple pole |
| 166 | 2.11:Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required. |
| 167 | 2.13.1:Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps |
| 168 | 2.14.2:Supplying and fixing following rating, double pole, (single phase and neutral),240 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 milli amperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps |
| 169 | 2.15.2:Supplying and fixing following rating, four pole, (three phase and neutral), 415volts, residual current circuit breaker (RCCB), having a sensitivity current 30milli Amperes in the existing MCB DB complete with connections, testing andcommissioning etc. as required.40 amps |
| 170 | 2.2.13:Providing and fixing following rating and breaking capacity MCCB withthermomagnetic release and terminal spreaders in existing cubicle panel boardincluding drilling holes in cubicle panel. making connections. etc. as required.100 Amp, 30 KA 4 Pole |
| 171 | 2.3.3:Supplying and fixing following way, single pole and neutral, sheet steel, MCBdistribution board, 240 volts, on surface/ recess, complete with tinned copperbus bar, neutral bus bar, earth bar, din bar, interconnections, powder paintedincluding earthing etc. as required. (But without MCB/RCCB/Isolator)12 way, Double door |
| 172 | 90.11.1.10:Supply and installation of sheet steel, phosphatised and painted, dust and vermin proof enclosure of MCB DB including copper /brass bus bar, neutral link, earth bus and DIN rail suitable for fixing MCB/ isolator etc. fixed on wall using suitable anchor bolts or fixed in recess including cutting hole on the wall , making good the damages, colour washing etc. as required4 way (8+12) - three phase double cover (IP 42/43) |
| 173 | 90.11.1.11:Supply and installation of sheet steel, phosphatised and painted, dust and vermin proof enclosure of MCB DB including copper /brass bus bar, neutral link, earth bus and DIN rail suitable for fixing MCB/ isolator etc. fixed on wall using suitable anchor bolts or fixed in recess including cutting hole on the wall , making good the damages, colour washing etc. as required6 way (8+18) - three phase double cover (IP 42/43) |
| 174 | 90.11.1.18:Supply and installation of sheet steel, phosphatised and painted, dust and vermin proof enclosure of MCB DB including copper /brass bus bar, neutral link, earth bus and DIN rail suitable for fixing MCB/ isolator etc. fixed on wall using suitable anchor bolts or fixed in recess including cutting hole on the wall , making good the damages, colour washing etc. as required4 way (8+12) - double cover TPN vertical DB with provision for fixing MCCB as incomer and SP/ TP MCB as outgoing (IP 42/43) |
| 175 | 90.12.7.27:Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.3.5 core 25 sq mm with factory made clamp |
| 176 | 90.12.6.27:Supply & laying of one No. PVC insulated and PVC sheathed armoured aluminium power cable of 1.1 KV grade of the following sizes in the existing masonry open duct as required.3.5 core 25 sq mm |
| 177 | 90.12.6.28:Supply & laying of one No. PVC insulated and PVC sheathed armoured aluminium power cable of 1.1 KV grade of the following sizes in the existing masonry open duct as required.3.5 core 35 sq mm |
| 178 | 90.12.6.32:Supply & laying of one No. PVC insulated and PVC sheathed armoured aluminium power cable of 1.1 KV grade of the following sizes in the existing masonry open duct as required.3.5 core 120 sq mm |
| 179 | 90.12.6.34:Supply & laying of one No. PVC insulated and PVC sheathed armoured aluminium power cable of 1.1 KV grade of the following sizes in the existing masonry open duct as required.3.5 core 185 sq mm |
| 180 | 90.12.6.37:Supply & laying of one No. PVC insulated and PVC sheathed armoured aluminium power cable of 1.1 KV grade of the following sizes in the existing masonry open duct as required.3.5 core 400 sq mm |
| 181 | 90.12.7.28:Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.3.5 core 35 sq mm with factory made clamp |
| 182 | 90.12.7.32:Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.3.5 core 120 sq mm |
| 183 | 90.12.7.37:Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.3.5 core 400 sq mm |
| 184 | 90.12.6.29:Supply & laying of one No. PVC insulated and PVC sheathed armoured aluminium power cable of 1.1 KV grade of the following sizes in the existing masonry open duct as required.3.5 core 50 sq mm |
| 185 | 90.12.6.41:Supply & laying of one No. PVC insulated and PVC sheathed armoured aluminium power cable of 1.1 KV grade of the following sizes in the existing masonry open duct as required.4 core 16 sq mm |
| 186 | 90.12.7.29:Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.3.5 core 50 sq mm with factory made clamp |
| 187 | 90.12.7.34:Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.3.5 core 185 sq mm |
| 188 | 90.12.7.41:Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.4 core 16 sq mm with factory made clamp |
| 189 | 9.1.20:Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X25 sq.mm (28mm) |
| 190 | 9.1.21:Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 35 sq. mm (32mm) |
| 191 | 9.1.22:Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2 X 50 sq. mm (35mm) |
| 192 | 9.1.25:Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2 X 120 sq. mm (45mm) |
| 193 | 9.1.27:Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 185 sq. mm (57mm) |
| 194 | 9.1.33:Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 16 sq. mm (28mm) |
| 195 | 9.1.31:Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 400 sq. mm (82mm) |
| 196 | 9.2.28:Supplying and making outdoor end termination with cast resin compound including aluminiumlugs and other jointing materials for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2 X 400 sq. mm |
| 197 | 2.12.1:Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps |
| 198 | 2.13.2:Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.63 amps |
| 199 | 2.15.3:Supplying and fixing following rating, four pole, (three phase and neutral), 415volts, residual current circuit breaker (RCCB), having a sensitivity current 30milli Amperes in the existing MCB DB complete with connections, testing andcommissioning etc. as required.63 amps |
| 200 | 90.12.6.1:Supply & laying of one No. PVC insulated and PVC sheathed armoured aluminium power cable of 1.1 KV grade of the following sizes in the existing masonry open duct as required.2 core 4 sq mm |
| 201 | 90.12.6.2:Supply & laying of one No. PVC insulated and PVC sheathed armoured aluminium power cable of 1.1 KV grade of the following sizes in the existing masonry open duct as required.2 core 6 sq mm |
| 202 | 90.12.7.1:Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.2 core 4 sq mm with factory made clamp |
| 203 | 90.12.7.2:Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.2 core 6 sq mm with factory made clamp |
| 204 | 9.1.1:Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.2 X 6 sq. mm (19mm) |
| 205 | OD70752/2026-2027:Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured copper power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.4core 1.5 sq mm with factory made clamp |
| 206 | 5.15:Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required. |
| 207 | 5.4:Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required. |
| 208 | 5.9:Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required.(Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm) |
| 209 | 90.16.1.3:Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required3.15 mm copper conductor ( 10 SWG) |
| 210 | 90.16.4.3:Supply and clamping the following sizes of strips on surface of wall / parapet/ existing cable tray using clamps fabricated from 20 x3 mm GI flat duly painted or heavy duty GI spacer saddles, spacing of clamps not exceeding 1 m , making good the damages, colour washing etc. as required ( for vertical run).25 x 6 mm GI strip |
| 211 | 90.16.5.3:Supply of superior quality copper earth socket for the following size of earth conductor including crimping etc. as required.3.15 mm (10 SWG) |
| 212 | 5.14:Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required. |
| 213 | 5.8:Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm) |
| 214 | 4.6.1:Supplying and installing following size of perforated Hot Dipped GalvanisedIron cable tray with perforation not more than 17.5%, in convenientsections, joined with connectors, suspended from the ceiling with G.I.suspenders including G.I. bolts & nuts, etc as required.100 mm width X 50mm depth X 1.6 mm thickness |
| 215 | 4.6.10:Supplying and installing following size of perforated Hot Dipped GalvanisedIron cable tray with perforation not more than 17.5%, in convenientsections, joined with connectors, suspended from the ceiling with G.I.suspenders including G.I. bolts & nuts, etc as required.450 mm width X 62.5 mm depth X 2.0 mm thickness |
| 216 | 4.6.11:Supplying and installing following size of perforated Hot Dipped GalvanisedIron cable tray with perforation not more than 17.5%, in convenientsections, joined with connectors, suspended from the ceiling with G.I.suspenders including G.I. bolts & nuts, etc as required.600 mm width x 62.5 mm depth x 2.0 mm thickness |
| 217 | 4.6.2:Supplying and installing following size of perforated Hot Dipped GalvanisedIron cable tray with perforation not more than 17.5%, in convenientsections, joined with connectors, suspended from the ceiling with G.I.suspenders including G.I. bolts & nuts, etc as required.150 mm width X 50 mm depth X 1.6 mm thickness |
| 218 | 4.6.4:Supplying and installing following size of perforated Hot Dipped GalvanisedIron cable tray with perforation not more than 17.5%, in convenientsections, joined with connectors, suspended from the ceiling with G.I.suspenders including G.I. bolts & nuts, etc as required.300 mm width X 50 mm depth X 1.6 mm thickness |
| 219 | 4.6.9:Supplying and installing following size of perforated Hot Dipped GalvanisedIron cable tray with perforation not more than 17.5%, in convenientsections, joined with connectors, suspended from the ceiling with G.I.suspenders including G.I. bolts & nuts, etc as required.375 mm width x 62.5 mm depth x 2.0 mm thickness |
| 220 | OD70754/2026-2027:Fabrication, supply, conveyance and installation of angle iron framework using suitable size angle iron, cut, fabricated and welded to the required shape, including one coat of zinc chromate primer and two coats of synthetic enamel paint, bolting the frame to the panel with necessary nuts and bolts, fixing the complete assembly to the wall, making good all damages, and completing the work in all respects as directed by the Engineer-in-Charge |
| 221 | OD70763/2026-2027:Supply, Installation, Testing and Commissioning of 7.5 HP Open Well Submersible Pump Set suitable for operation on 415 V ± 10%, 3 Phase, 50 Hz AC supply, consisting of open well submersible pump coupled with a 7.5 HP submersible induction motor of approved make. The pump shall be capable of delivering the designed discharge against the required total head and shall be suitable for continuous operation. The item shall include supply of pump and motor assembly complete with cast iron/stainless steel construction, stainless steel shaft, impellers, suction strainer, delivery outlet and all standard accessories as per manufacturer's specifications. The rate shall include the cost of all materials, labour, tools and tackles, conveyance, installation, testing, commissioning and all incidental charges complete as required and as directed by the Engineer-in-Charge. |
| 222 | OD70764/2026-2027:Supply, conveyance, installation, testing and commissioning of 70 W high efficiency LED street light system with 5 m octagonal GI pole including RCC foundation and all accessories complete in all respects. The LED luminaire shall be suitable for outdoor installation with pressure die-cast aluminium housing, pure polyester powder coated dark grey finish, IP66 protection with high purity PMMA lenses and toughened glass with silicone gasket for ingress protection. The luminaire shall have system efficacy ? 120 lm/W, lumen output ? 4200 lm, CRI ? 70, colour temperature 5700 K, LED life ? 50,000 hours (L70), and LED chips from Nichia/Cree/Osram or equivalent approved make. |
| 223 | OD70757/2026-2027:Supply, conveyance, installation, testing and commissioning of 9 W LED bulb suitable for operation on 230 V, 50 Hz AC supply. The bulb shall be energy efficient LED type with high luminous efficacy, suitable colour temperature (cool white/warm white as specified), long rated life, low power consumption, and conforming to relevant BIS/IEC standards. The work shall include supply of LED bulb with proper lamp holder connection, fixing in existing fittings, electrical connection, testing, commissioning, conveyance, labour charges and all incidental works complete as required and as directed by the Engineer-in-Charge. |
| 224 | OD70766/2026-2027:Supply, conveyance, installation, testing and commissioning of square slim surface mounted LED downlighter of wattage 15–18 W, complete with LED module, electronic driver, mounting accessories and all required fittings. The luminaire shall have die-cast aluminium housing for efficient heat dissipation, high-transmittance diffuser for uniform glare-free illumination, and pre-wired driver for easy installation and long service life. The fitting shall be suitable for operation on 150–270 V AC, 50 Hz supply and conform to relevant IEC/BIS standards. The luminaire shall have CRI ≥ 70, colour temperature ≥ 6000 K, IP20 protection, ambient operating temperature 0°C to 45°C, driver efficiency ≥ 85%, THD ≤ 20%, power factor ≥ 0.95, surge protection minimum 2 kV, and multistage isolated constant-current driver with SELV output voltage less than 60 V DC. The work shall include supply of all materials, fixing on ceiling/wall surface as required, electrical connections, testing, commissioning, conveyance, labour, tools and tackles and all incidental charges complete as required and as directed by the Engineer-in-Charge. |
| 225 | OD70765/2026-2027:Supply, conveyance, installation, testing and commissioning of 1200 mm 1×20 W LED tube light fixture (box type) suitable for wall mounting, complete with CRCA channel housing, white powder coated/pre-coated finish, aluminium body with PC diffuser and all accessories. The luminaire shall be suitable for operation on 110–265 V AC supply and shall have IP20 protection. The LED tube shall be 20 W, 6500 K colour temperature, having luminous output of approximately 2000 lumens, CRI ≥ 80, THD < 20%, surge protection ≥ 2 kV, and rated life of minimum 50,000 burning hours (L70). The driver shall be multistage isolated constant current type, conforming to IEC standards, with safety extra low voltage (SELV) output < 60 V DC, pre-wired for easy installation |
| 226 | 1.24.1:Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.5/6 amps switch |
| 227 | 1.24.3:Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.15/16 amp switch |
| 228 | 1.24.4:Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.3 pin 5/6 amp socket outlet |
| 229 | 1.24.5:Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.6 pin 15/16 amp socket outlet |
| 230 | 1.27.2:Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.3 Module (100mmX75mm) |
| 231 | 1.27.4:Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.6 Module (200mmX75mm) |
| 232 | 19.1:Supply, installation, testing and commissioning of 1200 mm sweep BEE-5 star rated ceiling fan with brushless direct current motor (BLDC) , class of insulation B , 3 no:s blades , 30 cm long down rod , 2no:s canopies, shackle kit, safety rope , copper winding, power factor not less than .9, service value (CM/M/W) minimum 6.00, Air delivery minimum 210 cum/min,350 RPM (tolerance as per IS :374-2019, THD less than 10% remote or electronic regulator unit for speed control and all remaining accesories including safety pin, nut and bolts , washers, temperature rise equal to 75 deg celsius ( maximum) , insulation resistance more than 2 Megaohm , suitable for 230V,50 Hz, single phase AC supply , earthing etc., complete as required: |
| 233 | OD70770/2026-2027:Supply, conveyance, installation, testing and commissioning of the 305 mm exhaust fans in the existing opening, fixing necessary bolt and nuts, making good the damages etc. as required including giving connections with required length of 24/0.20mm PVC insulated and PVC sheathed 3 core round copper conductor flex wire conforming to relevant ISS,305 mm, single phase, heavy duty, 1400 rpm exhaust fan in metal frame |
| 234 | OD70761/2026-2027:Supply, conveyance, installation, testing and commissioning of the 225mm exhaust fans in the existing opening, fixing necessary bolt and nuts, making good the damages etc. as required including giving connections with required length of 24/0.20mm PVC insulated and PVC sheathed 3 core round copper conductor flex wire conforming to relevant ISS,225mm metal frame |
| 235 | 90.4.8:Charges for cutting holes suitable for accommodating exhaust fans up to 305mm sweep including plastering colour washing etc. as required. |
| 236 | OD70769/2026-2027:Supply of 2 mm thick elastomeric fire retardant electrical insulating mat conforming to IS 15652:2006, suitable for 3.3 kV dielectric strength, Class A, anti-skid surface, supplied in rolls or sheets including manufacturer test certificate and BIS compliance |
| 237 | 2.3.1:Supplying and fixing following way, single pole and neutral, sheet steel, MCBdistribution board, 240 volts, on surface/ recess, complete with tinned copperbus bar, neutral bus bar, earth bar, din bar, interconnections, powder paintedincluding earthing etc. as required. (But without MCB/RCCB/Isolator)6 way, Double door |
| 238 | 90.11.1.20:Supply and installation of sheet steel, phosphatised and painted, dust and vermin proof enclosure of MCB DB including copper /brass bus bar, neutral link, earth bus and DIN rail suitable for fixing MCB/ isolator etc. fixed on wall using suitable anchor bolts or fixed in recess including cutting hole on the wall , making good the damages, colour washing etc. as required8 way (8+12) - double cover TPN vertical DB with provision for fixing MCCB as incomer and SP/ TP MCB as outgoing (IP 42/43) |
| 239 | OD70768/2026-2027:Supplying and fixing weatherproof SINDEX / Sintex-type enclosure box of size 240 mm × 130 mm × 110 mm, made of SMC / non-metallic insulated material, suitable for junctions, distribution, meter wiring and protection enclosures, complete with hinged cover, gasket, fixing clamps, screws, cable entry provisions, mounting accessories, duly installed, tested and commissioned, as required. |
| 240 | OD70760/2026-2027:Supply and providing 9 Litre capacity GI Fire Bucket painted in post office red with primer coat of red oxide and written with white paint 'FIRE' mounted on MS angle frame work/ wall bracket filled with fine sand, painting the bracket/ floor stand including making good the damages, colour washing etc. as required |
| 241 | OD70759/2026-2027:Supplying, installing, testing and commissioning of 24-hour analog timer switch for automatic control of lighting loads such as street lights, flood lights, etc., suitable for DIN rail mounting / panel mounting as applicable, with adjustable daily time program, manual override facility, and all necessary wiring, connections, accessories, fixing hardware, and commissioning works required for complete and satisfactory operation as directed by Engineer-in-Charge. |
| 242 | OD70751/2026-2027:Supply, installation, testing and commissioning of outdoor rooftop profile lighting system, comprising weatherproof LED profile / linear light fixture suitable for exterior rooftop application, IP65/IP66 rated aluminium body with UV resistant diffuser, high efficiency LED source of approved wattage and colour temperature, complete with suitable LED driver (constant voltage/constant current as required), mounting channels, clips, connectors, waterproof joints, drivers, wiring, sealing, fixing accessories and all associated works required for safe, complete and satisfactory installation on rooftop surfaces as directed by Engineer-in-Charge. |
| 243 | OD70755/2026-2027:Supply and provide earthing with CI earth plate 1200 mm x 1200 mm x 12.6 mm thick electrode including accessories, and providing masonary enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long etc. with charcoal/coke as required conforming to relevant IS and Electrical Inspectorate standards etc including excavation and refilling |
| 244 | OD70767/2026-2027:Painting letters or figures of the following sizes with enamel paint as identification mark to SB, DB, panel board etc as required 2.50 cm, 4 cm or 5 cm height |
| 245 | OD70771/2026-2027:Painting letters or figures of the following sizes with enamel paint as identification mark to SB, DB, panel board etc as required 6.5 cm, 8 cm or 13 cm height |
| 246 | OD70753/2026-2027:Charges for dismantling existing wiring of light, fan, bell points, etc., including removal of PVC conduits, wires, earthing conductors, circuit mains, and associated accessories, without damage wherever possible. The dismantled materials shall be carefully removed, coiled, and properly stacked in the electrical store room near the site as directed by the Engineer-in-Charge, and handed over with proper hand receipt. The rate shall include all labour, tools, handling, shifting, loading, unloading, and incidental charges. |
| 247 | OD70756/2026-2027:Charges for dismantling existing cables of sizes 4 sq.mm to 70 sq.mm, including removal of cable glands, earth clamps, and all associated accessories, carefully without causing damage wherever possible. The dismantled cables shall be properly coiled, stacked, and stored in the electrical store room near the site as directed by the Engineer-in-Charge, and handed over with a proper hand receipt. The rate shall include all labour, tools, handling, shifting, loading, unloading and incidental charges. |
| 248 | OD70762/2026-2027:Labour charges for dismantling existing switch boards, wiring points (wall and ceiling), light and fan points with or without ceiling rose, various sizes of distribution boards (DBs), and accessories such as RCCB, isolators, MCBs, air conditioners with stabilizers, etc., as per site conditions. The dismantled materials shall be carefully removed without damage wherever possible, properly stacked, and handed over to Forest Department authorities as directed by the Engineer-in-Charge. The same shall be recorded in the dismantled materials register maintained at site. The rate shall include all labour, tools, handling, shifting, loading, unloading and incidental charges. |
| 249 | OD70758/2026-2027:Charges for dismantling existing ceiling fan, replacing the shackle set, re-fixing the fan in position, and carrying out painting of the fan after proper surface preparation, cleaning, removal of rust, application of primer, and finish painting. The work shall also include replacement of designation labels, name plates, identification markings, and all minor accessories required for satisfactory operation, complete as required and as directed by the Engineer-in-Charge. The rate shall include all labour, tools, tackles, consumables, testing, and commissioning. |
| 250 | OD70773/2026-2027:Supply, Erection, Testing, Commissioning, Approval and Handing Over of One Passenger-cum-Freight Lift of 8-person capacity (544 kg), serving Ground Floor to Sixth Floor (G+6) with 7 stops/openings, suitable for installation in the existing lift well. The lift shall be provided with imported VVVF drive, 1.0 m/s speed, three-phase 415V induction motor, machine room above lift well, automatic telescopic doors, full-height infrared light curtain, door pressure limit switch, battery-operated automatic rescue device (ARD), inverter-based emergency alarm, serial communication-based LCE controller, Braille buttons, floor announcement system, intercom, overload protection, car and landing position indicators, micro push buttons, door open/close buttons, variable-speed door operation, SS hairline-finish cabin, granite flooring, SS handrail, 5A socket, emergency LED lighting with inverter backup, 1/2 toughened viewing glass in car and landing doors with framework, signal fixtures, LED bulkhead lighting in lift shaft at all floors, CCTV and PA system cabling up to machine room, replacement of existing electrical switchgear and associated power/control cables, earthing, minor civil works, and all accessories required for complete installation. The rate shall include design, fabrication, transportation, unloading, erection, testing, commissioning, statutory inspections, obtaining Electrical Inspectorate approval, operating license, insurance, warranty, documentation, buy-back arrangement, and all works complete as per EI, KSEB and relevant IS standards, complete and ready for operation.(Rate should be inclusive of buy back price) |
| 251 | OD70772/2026-2027:Comprehensive Annual Maintenance Contract (AMC) for passenger lift after expiry of warranty period for a duration of 5 years, including routine preventive maintenance (minimum one visit per month), attending unlimited breakdown calls, complete repairs, replacement of all defective parts, accessories, consumables, lubricants, and all materials required for safe and efficient operation of the lift. The scope includes testing, adjustment, servicing, and ensuring continuous safe operation. The contractor shall also be responsible for obtaining and renewing statutory approvals/licenses from Electrical Inspectorate (EI) and maintaining valid insurance throughout the contract period. The AMC shall be comprehensive and all-inclusive of manpower, spares, tools, and compliance requirements. |
| 252 | LIGHTENING PROTECTION SYSTEM |
| 253 | OD70736/2026-2027:Supply and installation of 8 mm solid aluminium round conductor (Rd 8 ALU) for terrace lightning protection application, semi-hard aluminium (E-AlMgSiO₅ as per DIN 48801), minimum cross-sectional area 50 sq.mm, conforming to DIN EN 50164-2 and DIN VDE 0185-305 (IEC 62305), including stainless steel base with polyamide adjustable conductor holder (adjustable width 185–260 mm), infinitely adjustable type with wing screw fast fixing arrangement, bottom section with 8.5 mm slot and M8 threaded connection, weather and temperature resistant from -35°C to +90°C, including all clamps, supports, fasteners, accessories, and installation at 1 m spacing as required for complete terrace lightning protection system and as directed by Engineer-in-Charge |
| 254 | OD70733/2026-2027:Supply and installation of 8 mm solid aluminium round conductor (RD 8/ALU) suitable for concrete buildings, semi-hard (E-AlMgSiO5 as per DIN 48801), with cross-sectional area of 50 sq.mm, conforming to DIN EN 50164-2 (VDE 0815 Part 202) and IEC 62305 / VDE 0185-305 standards, installed as vertical down conductor, including all accessories required for complete installation as per manufacturer specification and Engineer-in-Charge, fixed on wall surface using polyamide conductor holders with M8 female thread, fastened with M8 screws, weather and temperature resistant from -35°C to +90°C, with conductor holders spaced at 1 meter interval, complete in all respects including proper routing, bends, fixing, and termination. |
| 255 | OD70731/2026-2027:Supply and installation of 8 mm solid aluminium round conductor (RD 8/ALU) suitable for concrete buildings, semi-hard (E-AlMgSiO5 as per DIN 48801), with cross-sectional area of 50 sq.mm, conforming to DIN EN 50164-2 (VDE 0185 Part 202) and IEC 62305 / VDE 0185-305 standards, including all necessary accessories for complete installation, laid on parapet wall in horizontal run using polyamide conductor holders with M8 female thread, fixed with M8 screws, weather and temperature resistant from -35°C to +90°C, with conductor holders spaced at 1 meter interval, complete in all respects as per manufacturer specification and instructions of Engineer-in-Charge. |
| 256 | OD70729/2026-2027:Supply, installation, testing and commissioning of maintenance-free earthing system comprising of molecularly bonded copper earth electrode on low carbon steel of 3 m length, 14.2 mm diameter with 99.9% pure copper coating of 250 microns thickness, having fault current withstand capacity of 13 kA RMS for 1 second and peak current capacity of 31 kA, complete with SS 304 universal clamp (14–25 RTC) for termination, earth enhancing compound of mineral inert type with resistivity less than 0.2 Ω·m, non-corrosive, non-toxic and environmentally safe, provided @ 25 kg per pit for improving soil conductivity, and earth electrode inspection chamber made of polypropylene/polyethylene (UFE type) of size 250 mm × 250 mm × 250 mm with heavy-duty cover having load bearing capacity of 50 kN, complete in all respects as per specification and site requirement. |
| 257 | OD70734/2026-2027:Supply and fixing of cross connector / T connector for lightning protection system, suitable for routing vertical down conductors and forming mesh/grid connections, made of stainless steel / hot dip galvanised iron as specified, complete with 4 nos. M8×25 hexagonal bolts with M8 nuts, washers, and all necessary fasteners, clamps, corrosion protection materials, and accessories required for complete installation as per DIN VDE 0185-305 (IEC 62305) standards and as directed by Engineer-in-Charge. |
| 258 | OD70732/2026-2027:Supply and fixing of expansion piece with connector for lightning protection conductor system, suitable for equalizing temperature-induced length variations in conductors for runs exceeding 20 m, suitable for round aluminium conductor Rd 8, complete with T-cross and parallel connectors, quick installation type with hexagonal bolt M10×30, high-grade hot dip galvanised steel, conforming to DIN VDE 0185-305 (IEC 62305), including all necessary accessories, clamps, fasteners, and installation works as required for complete and proper functioning as directed by Engineer-in-Charge. |
| 259 | OD70730/2026-2027:Supply and fixing of equipotential bonding rail (test joint) for lightning protection system, suitable for DIN VDE 0100-410/540 and DIN VDE 0185-305 standards, with UV resistant polystyrene base and cover, stainless steel fittings, capable of 100 kA (10/350 µs) lightning current, complete with all required terminals for copper/aluminium conductors up to 25 sq.mm, fine stranded conductors up to 16 sq.mm, round cable Rd 8–10, and flat strip FL 30, including corrosion protection tapes, clamps, accessories, fixing, and complete installation as directed by Engineer-in-Charge. |
| 260 | OD70735/2026-2027:Supply, installation, testing and commissioning of hot dip galvanised steel flat (GI strip) 30 mm × 3 mm, 70 microns zinc coating (500 g/m²), conforming to DIN EN 50164-2 / IEC 62305, laid in earth trench for lightning protection earthing and equipotential bonding system complete with all accessories, clamps, connectors, jointing, fixing, and incidental works as required and as directed by Engineer-in-Charge. |
| 261 | OD70737/2026-2027:Supply and installation of PVC trapezoidal ducts, 1.5 m length each, including necessary fastening clamps, supports, joints, fittings, and all other accessories required for complete fixing and proper installation as per site conditions and manufacturer’s recommendations. |
| 262 | OD70728/2026-2027:Supply and fixing of cross connector suitable for flat conductor (30 mm galvanized steel strip), complete with 4 nos. hexagonal plate arrangement, including necessary clamps, bolts, nuts, washers, drilling, fixing, and all accessories required for proper installation as per manufacturer specification and Engineer-in-Charge, suitable for use in lightning protection system as per IEC 62305 standards, complete in all respects. |
| 263 | OD70727/2026-2027:Supply, installation, testing and commissioning of 3-meter air terminal (lightning interception rod) complete with accessories, comprising 16 mm diameter aluminium rod tapered to 10 mm (RD 10/ALU / E-AlMgSiO5 as per DIN 48801) conforming to DIN EN 50164-2 (VDE 0185 Part 202) and IEC 62305-3 standards, suitable for high wind load conditions, including Fang Fix base with top clamp assembly and cable bracket, designed for lightning current withstand capacity of 100 kA (10/350 µs waveform), mounted using anchors on concrete surface, including two numbers of 16 kg concrete ballast blocks (365 mm diameter) for stability, frost-resistant and stackable type, complete in all respects with all fittings, connectors, supports, and accessories required for proper installation as per manufacturer specification and Engineer-in-Charge. |
| 264 | DIESEL GENERATOR |
| 265 | OD70750/2026-2027:Supply, installation, testing and commissioning of 100 kVA, 3-phase, 415 V, 0.8 PF, 50 Hz radiator cooled diesel generator set (Prime Duty) comprising diesel engine and alternator of approved make, suitable for continuous operation and compliant with CPCB IV+ emission norms (latest CPCB standards). The DG set shall be complete with electronic governor, starting system, alternator, integral fuel tank, base frame, anti-vibration mounting pads, and all standard accessories required for safe and efficient operation. |
| 266 | OD70749/2026-2027:EXHAUST PIPES - Supplying and fixing exhaust gas piping of suitable dia, welded black M.S class 'B' pipe conforming to IS:3589 cut to required lengths and installed with necessary bends, supports, and clamps, anti-vibration mountings, insulation of exhaust system with mineral Wool / Rockwool, 50 mm thick wire mesh & aluminium cladding, etc. after applying one coat HR paint as per manufacturer recommendation, as required as per specifications. suitable rain cap for the top to avoid rainwater entry. The distance between the exhaust pipe at the top and the rain cap should be higher than the diameter of the pipe. The horizontal run of exhaust piping should slope downwards away from the engine to the condensate trap. Silencer should be installed with a drain plug at the bottom. Fixing shall be done with proper clamps, expansion bolts, and all other acessories as instructed by the Engineer, and the rate inclusive of all minor civil works required, bolts, clamps, etc as required for istallation. Support to exhaust piping should be done in such a manner that a load of exhaust piping is not exerted on the turbo charger and the vertical run of the pipes shall be provided with the indirect supporting method so that when the pipes are hot and expanded they will be lifted into the supports. Exhaust pipe height shall be 3m more than the top of any adjacent building within 10m radius of the exhaust for 100 kVA DG Set Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 24, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 11, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 17 daysAug 13, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 19 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender