Tender For special Repair To Bldg No T-221 And P-416 At Mil Station Bhusawal Under Ge(S) Ahilyanagar
Tender Value
43.90 Lakhs
Estimated cost
Bid Submission
12 Aug 2026
13 days left
EMD
88000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jalgaon → Maharashtra
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for special Repair To Bldg No T-221 And P-416 At Mil Station Bhusawal Under Ge(S) Ahilyanagar
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and as directed. |
| 2 | Demolition of reinforced cement concrete of any description and in any position (reinforcement cut to facilitate demolition) not otherwise specifically provided for complete all as specified and as directed. |
| 3 | M&L Reinforced cement concrete (Design mix) M-25 (20mm graded stone aggregate) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed. |
| 4 | M&L for PCC 1:4:8, type D2 (using 40mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and as directed. |
| 5 | M&L for brickwork with fly ash bricks, straight or curved on plan, exc 6 m mean radius, built in cement mortar 1:6 with and including demolition of existing brick work built in cement or cement lime mortar of any description complete all as specified and as directed. |
| 6 | Use and waste Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified.complete all as specified and as directed. |
| 7 | M & L for anti termite Treating to the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specified and as directed. |
| 8 | M & L for anti termite Treating the the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and as directed. |
| 9 | M & L for anti termite Treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall complete all as specified and as directed. |
| 10 | M & L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed. |
| 11 | S&F SS Grating with square frame (Grating thk- 1mm & frame thk- 1.5mm) of size 125mm (minimum) with/without waste-hole complete all as specified and directed. Note: Design of grating to be approved by Engineer-in-Charge. |
| 12 | S&F in repairs, rotational moulded polyethylene water storage tanks colour white (cylindrical vertical with closed top), 500 litres capacity, triple layered, hoisted and fixed in position including 20 mm dia ball valve, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed to iron pipe and connecting complete all as specified and as directed. |
| 13 | Taking up or down 15 mm bore dia GI steel tubing and connections complete all as specified and as directed. |
| 14 | S&F 15mm bore UPVC pipes Sch 40 including fittings, any length with fittings such as socket, elbow, bends, tees, reducer, union, caps plug, nipple etc complete laid in walls/ ceiling or laying in floor trench or fixed to walls complete all as specified and as directed. |
| 15 | Supplying and laying 16 mm outer dia of CPVC pipes SDR 11 & Brass CPVC SDR 11 fittings, any length with fittings such as socket, elbow, bends, tees, reducer, union, caps plug, nipple etc complete laid in walls/ ceiling or laying in floor trench or fixed to walls complete all as specified and as directed. |
| 16 | Taking up or down 20 mm bore dia GI steel tubing and connections complete all as specified and as directed. |
| 17 | S&F 20mm bore UPVC pipes Sch 40 including fittings, any length with fittings such as socket, elbow, bends, tees, reducer, union, caps plug, nipple etc complete laid in walls/ ceiling or laying in floor trench or fixed to walls complete all as specified and as directed. |
| 18 | S&F in repair Vitreous China, Squatting pan Orissa pattern size 580 x 440mm, white with integral foot rests (excluding flushing cistern and flush pipe) with Vitreous China ‘P’ or ‘S’ trap, front or back inlet including connection to trap and to flushing pipe, anti syphonage pipe, including PCC (1:2:4) type B-1 for fixing of WC and making good the floor to match the existing complete all as specified and as directed.Note: Cat No. S3010102 of CERA or equivalent model of makes specified |
| 19 | S&F in repairs, vitreous china wash down water closet (pedestal pattern) white, including connection to drain (or outgoing pipe) and flushing pipe, anti syphonage pipe, trap set and including white seat cover for pedestal pan with mild steel chromium plated aluminium hinging device, fixed to pan with suitable screws etc complete all as specified and as directed.Note: Cat No. S1053102 of CERA or equivalent model of makes specified. |
| 20 | S&F in repairs,Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.Note: Cat No F8030111AB of Cera or equivalent model of makes specified. |
| 21 | S&F in repairs 10 ltr capacity PVC valveless, syphonic action type flushing cistern, low level, white with inlet ball valve and handle including brackets complete all as specified and as directed.Make : Cat No. B1010110 of CERA or equivalent model of makes specified. |
| 22 | S&F vitreous china wash hand basin, white flat back of size 550 mm x 400 mm including brackets, 32 mm waste coupling brass chromium plated suitable for wash hand basins, with long screwed shanks and fly nuts and PVC waste pipe15mm dia, PVC connection pipe 450mm long complete all as specified and as directed.Note: Cat No. S2040141 of CERA or equivalent model of makes specified. |
| 23 | S&F in repairs, 15 mm bore pillar taps, cast copper alloy with capstan heads, fancy type, chromium plated screwed down high pressure with or without lettered 'HOT' or 'COLD' with long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as specified and as directed.Note: Cat No. F1015101 of CERA or equivalent model of makes specified. |
| 24 | S&F in repairs, bib tap 15mm dia, with wall flange and aerator screwed down for iron pipe or for brass ferrule complete all as specified and as directed.Make : Cat No. F1015151 of CERA or equivalent model of makes specified. |
| 25 | S & F in repairs, stop/ angle valves, 15mm dia, cast copper alloy, fancy type, chromium plated, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or unions complete all as specified and as directed.Make: Cat No. F1015201 of CERA or equivalent model of makes specified. |
| 26 | S & F in repairs, PVC connections, 15 mm size with PTMT nuts of length 600 mm complete all as specified and as directed. |
| 27 | S&F, Soap dish, chromium plated, fixed to plugs with chromium plated screws complete all as specified & as directed. |
| 28 | S&F in repair bevelled edge looking mirror 5.5mm thick of size 60cmx 45cm mounted on commercial plywood 6 mm thick including PVC beading all round and fixed to wooden plugs with chromium plated screws complete all as specified and as directed. |
| 29 | S&F in repairs wall mixer for mixing hot and cold water and bend for connecting to shower, 15 mm bore screwed for iron pipe and fixed complete all as specified and as directed.Make: Cat No. F1015401 of CERA or equivalent model of makes specified. |
| 30 | S&F in repair overhead shower rose 125mm size with 200mm long shower arm and wall flange complete all as specified & directed by Engr-in-charge.Make: Cat No. F7020111AB of CERA or equivalent model of makes specified. |
| 31 | S&F in repairs Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide, 60cm long with chromium plated bracket guard and railing complete all as specified and as directed. |
| 32 | S&F in repairs towel rail 60 cm long between flanges complete all as specified and as directed.Make : Cat No. F5015103CH of CERA or equivalent model of makes specified. |
| 33 | S&F in repairs, stainless steel sink with drain board made of 1mm thick sheet for kitchen with plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915 mm x 460 mm bowl size 410 mm x 350mm x 185 mm including CP waste coupling complete all as specified and as directed.Make: Cat No. SBSD 05 (RR) of JAYNA or Elegance Small of Nirali or equivalent model of makes specified. |
| 34 | Taking down chowkhats or frames with shutter (without taking out shutter from the frame), area n.exc 1.5 sqm each all as specified and as directed. |
| 35 | Taking down chowkhats or frames with shutter (without taking out shutter from the frame), area exc 1.5 sqm but not exc 4 sqm each all as specified and as directed. |
| 36 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65 x 125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. |
| 37 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. |
| 38 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 35 mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges 4 nos per leaf of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. |
| 39 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30 mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges 4 nos per leaf of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. |
| 40 | S&F 35 mm thick, second class hard wood, glazed and and skeleton shutters, factory made, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edge of framing plain, chamfered or rounded, fitted with cut and mitred beds for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.20 (a); supplied and fitted to chowkats all as specified and as directed. |
| 41 | S & F powder coated aluminum windows, three track, made out of aluminium sections including all necessary fittings, 5mm thick sheet glass, rubber/ neoprene beading, locking arrangements all as specified and as directed and comprising of following sections :- (a) Window frame: (i) Bottom-Section 20671 (Wt not less than 0.699 Kg/m) (ii) Top & Side - 20672 (Wt not less than 0.594 Kg/m)(b) Shutter: (i) Vertical (end)- 20669 (Wt not less than 0.548 Kg/m) (ii) Vertical (lock) - 20689 (Wt not less than 0.481 Kg/m) (iii) Bottom - 20718 (Wt not less than 0.263 Kg/m) (iv) Top - 20668 (Wt not less than 0.377 Kg/m)Note : Shade shall be as approved by Engineer-in-Charge. |
| 42 | S&F 100 mm long SS butt hinges, medium weight, cold rolled and fixed with screws/welded complete all as specified and as directed. |
| 43 | S&F 150 mm size extruded aluminium alloy handles fabricated type anodised and fixed complete all as specified and as directed. |
| 44 | S&F 200 mm size aluminium anodized barrel tower bolts of extruted section and fixed complete all as specified and as directed. |
| 45 | S&F 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed. |
| 46 | M&L for stainless steel wire cloth 0.36 nominal dia of wire and average width of aperture 1.40 mm and fixed with stanless steel staple to wooden/steel frames complete all as specified and as directed. Please Enable Macros to View BoQ information |
| 47 | M&L for stainless steel wire cloth 0.36 nominal dia of wire and average width of aperture 1.40 mm and fixed with stanless steel staple to wooden/steel frames complete all as specified and as directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 23, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 12, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 13 daysAug 14, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 15 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender