Tender For Establishment Of Honey Processing Unit At Chandsen Sub Project Stage-2 Malpura District Tonk
Tender Value
16.36 Lakhs
Estimated cost
Bid Submission
29 Jul 2026
2 days left
EMD
32720
Bank guarantee accepted
Document Fee
5000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Tonk → Rajasthan
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Establishment Of Honey Processing Unit At Chandsen Sub Project Stage-2 Malpura District Tonk
BOQ
| Sl. No. | Item Description |
| 1 | Excavation including loading, unloading, disposal and dressing of excavated earth within initial lead of 50m and lift up to 1.5m in dry or moist including dressing of excavated area, dewatering wherever required complete in all respect. Hard/Dense soil |
| 2 | Providing and Laying in position of Cement concrete Nominal mix (1:2:4) including leads of all construction materials, curing, compaction and finishing with rendering in cement sand mortar 1:3(1 cement :3coarse sand) and making good the joints excluding the cost of centering, shuttering and reinforcement. Well graded crusher broken stone aggregate of maximum size up to; 20 mm. |
| 3 | Random rubble stone masonary (using R.R. stone where 75% stones to be not less then 15cm in size in any direction and weighting not less then 23 kg.) for foundation including curing all leads of all construction materials including curing etc. complete.. In cement sand mortar 1:6 |
| 4 | Providing and laying Damp-proof course with cement concrete grade M-150 (1:2:4) mortar prepared with 1% solution of water-proof compound complete as per specification. 75mm thick. |
| 5 | Random rubble dry stone Kharanja under floor. |
| 6 | Brick masonry (using well burnt clay bricks of size 230 x 110 x 70 mm, class designation 75 as per specification) up to plinth including all leads of all construction materials including curing etc. In cement sand mortar 1:6complete.Add extra for superstructure brick masonry on |
| 7 | Cantering and shuttering for slabs, beams, lintels Columns, trough with or without caps and base including propping and remove. |
| 8 | Side shuttering including propping etc. complete (to achieve finish F2 for : Top or in abutments sluice wells etc. |
| 9 | Supplying of M.S. reinforcement including labour charges for bending binding and placing in position all reinforcement as per drawing including cost of binding wire and all leads and lifts using Tor or ribbed bars (IS :1786)Tor or ribbed bars (IS :1786-1985), |
| 10 | Providing and Laying in position of Cement concrete Nominal mix (1:1.5:3) including leads of all construction materials, curing, compaction and finishing with rendering in cement sand mortar 1:3 (1 cement : 3 coarse sand) and making good the joints excluding the cost of centering, shuttering and reinforcement. Well graded crusher broken stone aggregate of maximum size upto;(d)20mm |
| 11 | Plaster in cement sand morter 1:3 including racking of joints ,smoothfinishing &curing etc. complete including all leads of all construction material of thickness 12mm |
| 12 | Flush or ruled pointing on stone masonry including racking of joints and curing etc. complete including all leads of all construction materials in mortar ratio. (a) In Cement sand mortar 1:3. |
| 13 | Providing and fixing steel glazed doors windows and ventilator shutters of standard rolled steel section (IS 1038-1983) joints mitred and welded with steel lugs 13x3mm, 10cm. long embedded in cement concrete block 15x10x10cm. of 1:3:6 (1cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) or with wooden plugs and screws or rawl plugs and screws with fixing clips or with bolts and nuts as required including providing and fixing of plain glass panes 4mm thick with cooper glazing clips and special metal sash putty of approved make or metal beading with screws complete including priming coat of approval steel primer, excluding the cost of metal beading and other fitting except necessary hinges of pivots steel handles peg stay etc. as required : Windows side hung /Ventilators top or centre hung (openable) |
| 14 | Supplying and fixing rolling shutters of approved make, made of 80 x 1.25mm. M.S. laths interlocked together through their entire length and jointed together at the end by end locks mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete including cost of spring hooks, providing and fixing necessary 25.3cm. long wire springs grade No. 2 and M.S. top cover 1.25mm thick for rolling shutters as per design & IS 6248- 1979. (Clear openable area to be measured for payment). |
| 15 | Providing & fixing ball bearing for rolling shutters. |
| 16 | Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead and including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (upto any pitch in horizontal/ vertical or curved surfaces) excluding the cost of purlins, rafters and trusses and including cutting to size and shape whenever required. 10.1.1 1.00 mm thick with zinc coating not less than 275 gm/m2. |
| 17 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting (height upto 10 m) , fixing in position and applying a priming coat of approved steel primer all complete: |
| 18 | Kota stone slab flooring 25 mm thick over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) 11.18.1 For area of each slab from 901 to 2000 Sq.Cm. |
| 19 | Providing and fixing thermal insulation with Resin Bonded rock wool conforming to IS:8183, having density 48 kg/m3, 50 mm thick, fixed on the roof top with screws, rawel plug & washers and held and in position by criss crossing GI wire etc. complete as per directions of Engineer-in-charge. |
| 20 | Painting on G.S. sheet with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : New work (Two or more coats). |
| 21 | Providing and fixing Square bars or other flat welded to window, ventilatiors etc. |
| 22 | Colour washing of all shades to give an even shade including all scaffolding : New work (two or more coats) with a base coat of white washing with lime. |
| 23 | Wiring of light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) in recessed ISI marked MMS ( IS:9537 P - III ) virgin material PVC conduit & it's ISI marked (IS:3419-1988) accessories, round tiles, 1.2 mm thick Hot DippedGalvanized Modular Box with earth terminal, 10A Modular switch,Modular face plate with grid plate, 3 pin ceiling rose / Holder /3 way connector, screws, making connections, testing etc. as required. For specification of copper Conductor, Phenolic Laminated sheet's & Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07 For additional technical parameters of product / work refer |
| 24 | Short point (up to 3 mtr.) |
| 25 | Medium point (up to 6 mtr.) |
| 26 | Wiring of 3/5 pin 6 amp. Light plug point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade(IS:694) in recessed ISI marked MMS ( IS:9537 P - III ) PVC conduit & it's ISI marked (IS:3419- 1988)accessories, Hot Dipped Galvanized Modular box of 1.2 mm thick with earth terminal, 10 A modular switch, 3/5 pin 6 A modular socket, Modular face plate with grid plate, screws, making connections, testing etc. as required. For specification of copper Conductor, Phenolic Laminated sheet's & Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07 For additional technical parameters of product / work refer a. On board Item no. (1.3.1) |
| 27 | S&F following sizes (dia.) of ISI marked virgin material MMS ( IS:9537 P - III ) PVC conduit along with ISI marked (IS:3419-1988) accessories as required in recess including cutting the wall, covering conduit and making good the same as required. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR. PVC conduit 25mm. |
| 28 | Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor as per PWD specification for electrical Works with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from 99.90 % purity copper, class 5 stranding in acc. to IS:8130/IEC 60228 for lower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5, in existing surface or recessed PVC/ MS conduit/casing capping making connections with Copper Lugs of suitable size, Ferrules,testing etc. as required. OEM Must have its own in house NABL lab setup for all testing facilities for wires. For additional technical parameters of product / work refer |
| 29 | 2 x 2.5 sq. mm. + 1x1.5sqmm |
| 30 | 4.1.22 2 x 10.0 sq.mm |
| 31 | Providing & Fixing of Recessed/surface mounting heavy duty horizontal type Double Door ( Metal / Glazed )Distribution boardwith Metal end box made out from Galvanized steel / CRCA sheet not less then 1.2 mm thick conforming to IS-8623-1 & 3 / IEC 61439- 1 & 3, powder painted complete with reversible door (for double door DB only )100 amp. insulated copper bus bar/shorting link , copper neutral link, copper earth link , color coded interconnecting wire set of suitable rating and din bar,masking sheet, making internal DB terminations with copper lugs, Ferrules, detachable gland plate, including making connections, testing etc. as required. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test reports & All as per pre approved by Engineer in charge. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR . Metal door (single phase) IK-09 and IP-43 with Metal end box a. 4 Way (4+2) |
| 32 | Providing & Fixing of 240/415 V isolator ISI marked IS:13947-III/conforming to IEC 60947-3, suitable for AC22A utilization category, 4KV impulse withstand voltage, true contact indication, Red colour dolly / lever shall have single mould covering over all poles for operation , two position din rail mounting, minimum phase termination capacity of 35sq.mm. IP 20 contact protection and fitted in existing distribution board / sheet including making connections, testing etc. as required. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test reports & All as per pre approved by Engineer in charge.For additional technical parameters of product / work refer Double pole isolator 63 A rating |
| 33 | Providing & Fixing of 240/415 V AC MCB with positive isolation of 10 kA breaking capacity (B/ C/D tripping characteristic as per type of load and site requirement) 4 KV impulse withstand voltage, ISI marked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC 60947- 2, low watt losses, trip free mechanisum , energy limiting of class 3 as per IEC, minimum phase termination capacity of 35sq.mm. , conductor line load reversibility , IP 20 contact protection and fitted in existing distribution board/sheets, minimum electrical operation 20,000 upto 20 A rating and 10,000 upto 63 A, 5000 for 80 A & above rating including making connections, testing etc. as required. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test reports & All as per pre approved by Engineer in charge. For additional technical parameters of product / work refer a. 6 A to 32 A rating |
| 34 | Providing & Fixing of energy efficient /energy saving IP 20 LED direct retrofit Bulb in existing holder or fixture as required with system lumen efficacy ≥100 lm/Watt output ,pf 0.95 , CRI >70, minimum life time of minimum 25000 Burning Hours with , 70% of intial Lumen maintaned till life ends , CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin) , maximum power consumption should not more than the specified rating and Fixture shall be of BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) certificate / Report from OEM shall be submitted. All as per pre approved by engineer in charge . for additional technical parameters of product/ work, refer |
| 35 | 9 Watt (item no. 17.9.3) |
| 36 | 18/20 Watt (17.9.5) |
| 37 | Providing & Fixing of BEE Star rated copper wounded double ball bearing capacitor start, aluminium body & Metallic blade ceiling fan Conforming to all the performance requirements laid down in IS 374:2019 including all amendments, as applicable ; & Carry BIS licensing (i.e. ISI marking) with down rod up to 80 cm with secondary support safety cable ( steel rope) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer 1200 mm Sweep BEE 2 Star rated (service value >=4.5 to < 5 ) |
| 38 | Providing & Fixing of Heavy duty capacitor start, copper wound Double ball bearing 900/1400 RPM single phase Exhaust fan conforming to IS:2312 ISI marked in existing opening including making connections testing etc. as required. All as per preapproved by Engineer in charge. For additional technical parameters of products/ work , refer |
| 39 | P & F WVC Wash basin (Ist quality IS:2556 Mark) of approved make with C.I. brackets duly painted 1 No. 15 mm C.P. Pillar cock (IS:8934 Mark) & 32 mm C.P. brass waste coupling of approved make, P.V.C Waste pipe with PVC nut 32 mm complete including cutting & making good the wall .Size 510 mm x 400 mm |
| 40 | P & F G.I. pipes (Internal Work) with G.I. Fittings excluding union (IS:1239 Mark) & MS clamps including cutting and making good the walls and floors:15 mm dia nominal bore 'A' ClassPWD Building BSR 2022 TONK Item no. 2.1.1 AChap.S2 |
| 41 | P & F Bib Cock (IS : 8931 Mark), Superior quality of approved make: Brass 400 grm,15mm nominal bore.PWD Building BSR 2022 TONK Item no.2.7.1Chap.S2 |
| 42 | Supply & Fixing of Water + AFFF 6% Mechanical Foam type Fire Extinguisher (Stored Pressure type) conforming to IS:15683:2018 , Powder coated Internal & External Surface Deep drawn cylinder body of Mild Steel CR2 grade conforming to IS: 513, Squeeze grip Forged brass release valve with Inbuilt safety release device, Diaphragm Type, 0 to 25 bar range pressure gauge, 450 mm long EPDM discharge tube, QR code for Product Traceability including Fixing on wall with suitable Anchor Fasteners as required of following capacity. Test Certificates of all the Parameters along with Hydro test & Burst test (For Cylinder Body) Certificate from OEM / External NABL Accrediated Lab is to be submitted. All as per preapproved by Engineer in charge. For additional technical parameters of products/work, refer. |
| 43 | Description and Specification of 50 Kg/Hr. Bucket Heating tank 4 buckets (of 30 litres Capacity) SS 304 Tank on a stand of minimum 4\\" high. Pre Heating Tank: Honey heating tank and Honey Mixing tank. Capacity (Liters): 50 litres, SS 304, Gear Pump with a 1 HP Single Phase motor (Crompton or equivalent make). jacketed tanks, Stirrer inside for continuous stirring. Drain pipe for cleaning. SS 304 Storage Tanks 1 Nos 200 Litres Capacity 5 mm thickness on stand. With tapped Drain to clean Honey Heating (Heater)1 Nos make 3 KW Single Phase SS 304, Honey Moisture reduction tank 1 Nos. SS 304, Gear Pump motor (Crompton or equivalent make) 1HP, single phase, with pressure Honey Filtration 1 Set of: 3 (Three) Filter microns stages of filtration one receiving to heating tanks, after moisture reduction/ There are three filters the main filter (Filter Clothes 200 Microns and other two filters are made from Stainless steel 304 mesh (120 Square inch.) Processed Honey storage 1 Nos Capacity 200 litres, SS 304,5 mm thickness on stand Filling Machine Capacity 50 grams to 500 grams Single Nozzle. Air Compressor 150 Pound pressure All connecting piping between tanks of SS 304 Control panel with wiring up to supply power point (30 meters) and for each equipment Lab Equipment Refractometer for honey brix and moisture testing. Brix Scale 58-92, Refractive Index 58-92, Digital weighing Scale, Digital weighing Scale, Capacity 200 Kg. with 2 x 2 feet stainless steel platform and digital display. Digital weighing Scale, Capacity 5 Kg. with 1 x 1 feet max, stainless steel platform and digital display, waterproof loadcell, Along with one each of 1kg, 500 gm and 50 gms, 20 gms and 10 gm standard weight stones Induction sealing machine for Bottle scaling machine up to 100 mm Hand Pallet Truck: 1.5 Mt Capacity and 10 plastic pallets (1 X 0.8) meters Label Printing machine hand held 5 line, Handy Batch Coder Machine For MRP, Expiry Date Print hand held 5 line. Handy Batch Coder Machine For MRP, Expiry Date Print Plastic Pallets: 10 Nos Flat Top (1000 X 800 X 125 mm), injection moulded, static weight 1000 kg unified load, Dynamic 500 g min Material HDPE/PP Others: Transportation, Transit Insurance, 3 year warranty Insuranc after 1 year from installation, 3 year Annual Maintenance Contract after 1 year from installation, training 2 days, spares, tool box etc. Non BSR item approved by Office of the Chief Engineer, Water Resources, Rajasthan, Jaipur |
| 44 | Description and Specifications for Solar Unit 10 KW PV Panel make:- Reputed Indian MNRE Approved Make Panel: Polycrystalline / Monocrystalline Bifacial /Topcon Wattage: 540-620 WP(NDCR Inverter: Standard/Inverter, Inverter Type- Hybrid Inverter Capacity:-10 KW Battery: Li-PO4 battery suitable with solar system Structure: GI Standard (Height 6 Feet) Balance of System: Included, AC Cable- Polycah/Reputed-30meter DC Cable- Polycab/Reputed-200meter ACDB-1 nos IP rating IP65 or IP 66 capacity 10KW, Three Phase, Voltage Rating 415 V AC, Current rating 32A, UV Protected, Transparent Plycarbonate or ABS Box, AC Miniature Circuit Breaker (MCB); Surge Protection Device (SPD): A 3 Plle, AC 40kA Type 2 SPD; Terminal Blocks: Copper Terminal blocks for secure AC Connections. Cable Glands All Accessories Included: -Lugs, MC4 Connector, etc Earthing copper Electrode-3nos; Copper Bonded rods with a diameter of at least 40 mm and a length of 1-2 meters, Bentonite Chemical Earthing bag 10 Kg, Nut Bolt with Washer 1 set, Ring Lug 1 Nos. Earthing cable: 50 meter, 6 Sqmm dia, conduction material: Tinned Copper, Insulation material: PVC Colour: Yellow/Green; Spart Test KV 6(ac) Non Breakdown; Rated Temperature 70 Deg C, Rated Voltage AC 450/750 V, DC 1000 v, European CPR: nCca/ Dca/Eca. according tot EN50575 Certification of TUV/CE. Construction (2AWG) X 35n X mm2, Conductor Coinstruction 494 X 0.3 X 2mm, Conductor :8.8 mm, Resistance Max: 0.536 Ohms/Km, Curret Carring Capacity 218 A. Side shuttering including propping etc. complete (to achieve finish F 2 for : Top or intermediate bed plates, in between masonry or piers, abutments sluice wells etc. WRD Jaipur BSR 2023 Ch X Item 1B Pg 32 Lightening Arrestor - Inos, Solar Copper Lightning Arrester (up to 100 micron copper bonded), Solid rod with 14.2 mm diameter, Dimensions LXWXH 100X5X5 cm, Lightening arrester blase plate, item weight 12 Kg. On GI Stand Meters/ Net Metering- HPL/Equal Standard. Others: Transportation, Transit Insurance, 3-year warranty after 1 year from installation, 3-year Annual Maintenance Contract after 1 year from installation, Training 2 days, spares, tool box etc. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 24, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 29, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 2 daysJul 30, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 3 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender