Tender For Construction Of District Youth Skilling Entrepreneurship And Employment Centres At Churachandpur District , Manipur Under Part-1 Of Scheme For Special Assistance To State For Capital Investment Fy 2022-2023
Tender Value
6.58 Crore
Estimated cost
Bid Submission
30 Jul 2026
2 days left
EMD
13.17 Lakhs
Bank guarantee accepted
Document Fee
25000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Imphal West → Manipur
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Construction Of District Youth Skilling Entrepreneurship And Employment Centres At Churachandpur District , Manipur Under Part-1 Of Scheme For Special Assistance To State For Capital Investment Fy 2022-2023
BOQ
| Sl. No. | Item Description |
| 1 | (i) GROUND FLOOR |
| 2 | SH : EARTH WORK |
| 3 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan),including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil. |
| 4 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. |
| 5 | Supplying and filling in plinth with sandy soil under floors i/c watering, ramming consolidating and dressing complete |
| 6 | Providing and laying and compacting Granular Base/Sub base according to lines, graded and cross section by using naturally occurred sand gravel/conforming to IRC- Grade-II of MOST specification free from organic or other deterious constituent spread with mortar grader and compacted by rolling with power roller of 8-10 capacity in layers not exceeding 150mm (spread thickness) i/c rolling of the road surface to proper level and grade 30 cm width edging on both side etc. complete as directed by Engineer- in -charge. |
| 7 | SH : CONCRETE WORKS |
| 8 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :(a) 1:5:10 (1 cement : 5 kanhaighat coarse sand : 10 graded stone aggregate 40 mm nominal size) |
| 9 | b)1:2:4 (1 cement : 2 kanhaighat coarse sand : 4 graded stone aggregate 20 mm nominal size) |
| 10 | SH : R.C.C. WORKS |
| 11 | Providing and laying in position specified grade of reinforced cement concrete,excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :(a)1:1.5:3 (1 cement : 1.5 kanhaighat coarse sand : 3 graded stone aggregate 20 mm nominal size) |
| 12 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers,abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :(a)1:1.kanhaighat 5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) |
| 13 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level,excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 kanhaighat coarse sand : 3 graded stone aggregate 20 mm nominal size). |
| 14 | Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto & above plinth level.(b) Thermo- Mechanically Treated bars. |
| 15 | FORM WORKS |
| 16 | Centering and shuttering including strutting, propping etc. and removal of form for(a) Foundations, footings, bases of columns, etc. for mass concrete |
| 17 | (b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick |
| 18 | ( c ) Suspended floors, roofs, landings, balconies and access platform with water, proof ply 12mm thick |
| 19 | (d) Columns, Pillars, Piers, Abutments, Posts and Struts |
| 20 | (e) Edges of slabs and breaks in floors and walls Under 20 cm wide |
| 21 | (f) Stairs, (excluding landings ) except Spiral- staircase |
| 22 | BRICKS WORKS |
| 23 | Brick work with 1st class common burnt clay F.P.S. (non modular) bricks in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 kanhaighat coarse sand) |
| 24 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1cement :4 coarse sand) |
| 25 | WOOD WORKS |
| 26 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).(a)Local best quality teak wood |
| 27 | Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows i/c ISI marked MS butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for separately,, all complete as per direction of Engineer-in-charge. (a) Local best quality teak wood, 35 mm thick shutter |
| 28 | Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows( Area of opening for panel insers excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25mm to 40 mm thick), (a) Local best quality teak wood |
| 29 | Providing and fixing glazed shutters for door, windows and clerestory windows using 4 mm thick float glass panes including ISI marked MS pressed butt hinges bright finished of required sizes with necessary screws |
| 30 | Providing 40x5mm flat iron hold fast 40cm long i/c fixing to frames with 10mm dia bolts, nuts and wooden plugs and embedding to cement concrete block 30x10x15cm 1:3:6 (1 cement : 3 coarse sand: : 6 stone aggrt. 20mm nominal guage). |
| 31 | Providing and fixing aluminium sliding door bolts ISI marked (anodic coating not less than grade AC 10 as per IS: 1868)transparent or dyed to required colour or shade with nuts and screws etc. complete: (a) 300X16 mm |
| 32 | Providing and fixingaluminium tower bolt ,ISI mareked, anodised (anodic coating not less than grade AC 10 as per IS :1868) transparent or dyed to required colour or shade with necessary screws etc. complete:(a) 250X10 mm |
| 33 | (b) 150x10 mm |
| 34 | Providing and fixinng aluminium handles, ISI marked,anodised (anodic coating not less than grade AC 10 as per IS :1868) transparent or dyed to required colour or shande with necessary screws etc complte:. (a)125mm |
| 35 | (b) 100 mm |
| 36 | Providing and fixing stainless steel (grade 304 ) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, ( for payment purpose only weight of stainless steel members shall be considered e/c fixing accessories such as nuts, bolts, fasteners etc ) |
| 37 | SH : FLOORING |
| 38 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades,laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc.,complete. (a) Size of Tile 600x600 mm |
| 39 | Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 kanhaighat coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.(a) Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye orequivalent. |
| 40 | Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red, Brown laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Kanhaighat coarse sand) including pointing the joints with white cement and matching pigment etc., complete. |
| 41 | Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by themanufacture of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 Kanhaighat coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete |
| 42 | SH : FINISHING |
| 43 | 12mm cement plaster of mix 1:4 (1 cement : 4 kanhaighat coarse sand). |
| 44 | 15mm cement plaster on rough side of single or half brick wall of mix1:4 (1 cement : 4 kanhaighat coarse sand). |
| 45 | 15 mm cement plaster 1:3(1 cement:3 coarse sand)finished with a floating coat of neat cement on the roughside of single or half brick wall |
| 46 | Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface.(a)water thinnable cement primer |
| 47 | Providing and applying white cement based putty of average thickness 1mm of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 48 | Finishing walls with Acrylic Smooth exterior paint of required shade:- new work (two or more coat applied @ 1.67 ltr/10sqm over and i/c base coat of water proofing cement paint applied @2.20 kg/10sqm. |
| 49 | Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade.(a) two or more coats on new work. |
| 50 | Finishing walls with Deluxe Multi surface paint system for interiors and exteriors using primer as permanufacturers specifications (b)Painting steel work with Deluxe Multi Surface paint to give an even shade.Two or more coat applied @ 0.90 ltr/10sqm over an under coat of primer applied @ 0.80 ltr/10sqm of approved brand or manufacture. |
| 51 | Finishing walls with Deluxe Multi surface paint system for interiors and exteriors using primer as permanufacturers specifications (a) Painting wood work with Deluxe Multi Surface paint of required shade.Two or more coat applied @ 0.90 ltr/10sqm over an under coat of primer applied @ 0.75 ltr/10sqm of approved brand or manufacture. |
| 52 | Providing & fixing M.S. grills of required pattern in frames of window etc with M.S. flats, square or round bars etc i/c priming coat with approved steel primer all complete.(a) Fixed to openings/ wooden frames with rawl plugs screws etc. |
| 53 | MISCELLANEOUS |
| 54 | Making plinth protection 50 mm thick in cement concrete 1: 3 : 6 (1 cement : 3 coarse sand : 6 graded stone aggrt. of 20 mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand i/c finishing the top smooth. |
| 55 | 2nd class brick masonary 15x15cm open surface drain in c.m. 1: 5(1cem : 5 c/sand) i/c earth excavation 10cm bed c.c.1: 5 : 10 1cem : 5 c/sand :10gr.st.aggrt.40mm n/size i/c 12mm thick cement plaster 1: 3 (1cem : 3c/sand) with a floating coat of neat cement inside & outside as per standard design. |
| 56 | Providing and laying 60 mm thick factory made cement concrete interlocking paver block (Rubber Moulded) of M-30 grade made by block making machine with strong vibratory compaction and of approved size and design / shape laid in required colour and pattern over and including 50 mm thick compacted bed of Kanhaighat coarse sand, filling the joints with Kanhaighat coarse sand etc. all complete as per the direction of the Engineer-in-charge. |
| 57 | (ii) FIRST FLOOR |
| 58 | SH : R.C.C. WORKS |
| 59 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers,abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : (a)1:1.kanhaighat 5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) |
| 60 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level,excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 kanhaighat coarse sand : 3 graded stone aggregate 20 mmnominal size). |
| 61 | Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto & above plinth level.(b) Thermo- Mechanically Treated bars. |
| 62 | FORM WORKS |
| 63 | Centering and shuttering including strutting, propping etc. and removal of form for (b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick |
| 64 | ( c ) Suspended floors, roofs, landings, balconies and access platform with water, proof ply 12mm thick |
| 65 | (d) Columns, Pillars, Piers, Abutments, Posts and Struts |
| 66 | (f) Edges of slabs and breaks in floors and walls Under 20 cm wide |
| 67 | BRICKS WORKS |
| 68 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1cement :4 coarse sand) |
| 69 | WOOD WORKS |
| 70 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).(a)Local best quality teak wood |
| 71 | Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows i/c ISI marked MS butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for separately,, all complete as per direction of Engineer-in-charge. (a) Local best quality teak wood, 35 mm thick shutter |
| 72 | Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows( Area of opening for panel insers excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25mm to 40 mm thick), (a) Local best quality teak wood |
| 73 | Providing and fixing glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes i/c ISI marked MS pressed butt hinges bright finished of required sizes with necy screws (a) Local best quality teak wood 35mm thick |
| 74 | Providing 40x5mm flat iron hold fast 40cm long i/c fixing to frames with 10mm dia bolts, nuts and wooden plugs and embedding to cement concrete block 30x10x15cm 1:3:6 (1 cement : 3 coarse sand: : 6 stone aggrt. 20mm nominal guage). |
| 75 | Providing and fixing aluminium sliding door bolts ISI marked (anodic coating not less than grade AC 10 as per IS: 1868)transparent or dyed to required colour or shade with nuts and screws etc. complete: (a) 300X16 mm |
| 76 | Providing and fixingaluminium tower bolt ,ISI mareked, anodised (anodic coating not less than grade AC 10 as per IS :1868) transparent or dyed to required colour or shade with necessary screws etc. complete:(a) 250X10 mm |
| 77 | (b) 150x10 mm |
| 78 | Providing and fixinng aluminium handles, ISI marked,anodised (anodic coating not less than grade AC 10 as per IS :1868) transparent or dyed to required colour or shande with necessary screws etc complte:. (a)125mm |
| 79 | (b) 100 mm |
| 80 | STEEL WORK |
| 81 | Providing & fixing M.S. round holding down with nuts & washer plates completes. |
| 82 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(a) Electric resistance or induction butt welded tubes |
| 83 | P/F 1mm thick M.S.Sheet eaves board with ISA 25x25x4mm and flat 25x4mm with primer and painting complete as per direction of Engineer-in- Charge. |
| 84 | Providing & fixing M.S. grills of required pattern in frames of window etc with M.S. flats, square or round bars etc i/c priming coat with approved steel primer all complete.(a) Fixed to openings/ wooden frames with rawl plugs screws etc. |
| 85 | ROOFING & CEILING WORKS |
| 86 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trussesand including cutting to size and shape wherever required with (a)precoated galvanised iron profile sheets 0.50 mm thick. |
| 87 | Providing and fixing precoated galvanised steel sheet roofing accessories, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I seam bolts and nuts, G.I plain and bitumen washers complete : Ridges plain (500 - 600mm) (a) precoated galvanised iron profile sheets 0.50 mm thick. |
| 88 | Providing and fixing at all height false ceiling including providing and fixing of frame work made of special section, power pressed from MS sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS:277 and consisting of angle cleats of size 25 mm wide X 1.6 mm thick with flages of 27mm and 37 mm, at 1200 mm c/c, one flange fixed to the ceiling with dash fasterner 12.5mm dia x 50 mm long with 6mm dia bolts, other flange of cleat fixed to the angle hanger of 25x25x0.55 mm of reqd length with nut and bolts of reqd size and others end of the angle hanger fixed with intermediate GI channel 45x15x0.9mm running at the spacing of 1200 mm c/c, to which the ceiling section 0.5 mm thick bottom wedge of 80mm with tappered flanges of 26 mm ieach having clip of 10.5 mm at 450 mm c/c, shall be fixed ina direction perpendicular to thr GI intermediate channel with connecting clip made out of 2.64mm dia x 230 mm long GI wires at every junctionm i/c fixing perimeter channels 0.5 mm thick 27 mm height having flanges of 20 mm and 30 mm long. the perimeter of ceiling fixed to wall/ partition with the help of raw plug at 450 mm center, with 25 mm long drive-all screw |
| 89 | i/c joining and finishing to a flush finish of tapered and square edge of the board with reccommended jointing compound, jointing taps, finished with the jointing compounds in three layers covering upto 150 mm on both side of the joint and 2 coat of primer suitable for board, all as per manufacture's specification and also i/c the cost of making openings for light fitting, greens, diffuser, cut out made with frame of the perimeter channel suitably fixed, all complete as per drawings, and specification and direction of the Engineer-in-charge but e/c the cost of the painting with : i) Fully Perforated Gypsum Plaster Board of size 1200X2400X12.5 mm having approx. 15% perforated size and pattern as approved by Engineer-in-charge and as per manufacture specification, with all 4 side tapered and block by acoustical tissue with NRC value not less than 0.60. |
| 90 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades,laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc.,complete. (a) Size of Tile 600x600 mm |
| 91 | Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red, Brown laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Kanhaighat coarse sand) including pointing the joints with white cement and matching pigment etc., complete. |
| 92 | Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by themanufacture of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 Kanhaighat coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete |
| 93 | SH : FINISHING |
| 94 | 12mm cement plaster of mix 1:4 (1 cement : 4 kanhaighat coarse sand). |
| 95 | 15mm cement plaster on rough side of single or half brick wall of mix1:4 (1 cement : 4 kanhaighat coarse sand). |
| 96 | Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface.(a)water thinnable cement primer |
| 97 | Providing and applying white cement based putty of average thickness 1mm of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 98 | Finishing walls with Acrylic Smooth exterior paint of required shade:- new work (two or more coat applied @ 1.67 ltr/10sqm over and i/c base coat of water proofing cement paint applied @2.20 kg/10sqm. |
| 99 | Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade.(a) two or more coats on new work. |
| 100 | Finishing walls with Deluxe Multi surface paint system for interiors and exteriors using primer as permanufacturers specifications (b)Painting steel work with Deluxe Multi Surface paint to give an even shade.Two or more coat applied @ 0.90 ltr/10sqm over an under coat of primer applied @ 0.80 ltr/10sqm of approved brand or manufacture. |
| 101 | Finishing walls with Deluxe Multi surface paint system for interiors and exteriors using primer as permanufacturers specifications (a) Painting wood work with Deluxe Multi Surface paint of required shade.Two or more coat applied @ 0.90 ltr/10sqm over an under coat of primer applied @ 0.75 ltr/10sqm of approved brand or manufacture. |
| 102 | (iii) Water Supply & Sanitary Installation |
| 103 | Earth work in excavation by mechanical means (Hydraulic Excavator)/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed,within a lead of 50 m.(i) All kinds of soil. |
| 104 | Filling available excavated earth (excluding rock) in trenches, plinth,sides of foundations etc. in layers not exceeding 20cm in depth,consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. |
| 105 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering : All work upto plinth level (a) 1:3:6 (1 cem :3 Kanhaighat Coarse Sand:6 graded stone aggrt.40mm n/size). |
| 106 | (b) 1:2:4 (1 cem :2 Kanhaighat coarse sand:4 graded stone aggrt.20mm n/size). |
| 107 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement :1.5 Kanhaighat coarse sand:3 graded stone aggregate 20 mm nominal size.) |
| 108 | Reinforcement for R.C.C. work including straightening, cutting,bending, placing in position and binding all complete up to plinth level/Above Plinth level. ( a ) Thermo-Mechanically Treated bars |
| 109 | Centering and shuttering including strutting, propping etc. and removal of form for: |
| 110 | (b) Suspended floors, roofs, landings, balconies and access platform,with water proof ply 12mm thick. |
| 111 | (C) Edges of slab and breaks in floors and walls (i) Under 20cm wide |
| 112 | Brick work with Ist class common burnt clay F.P.S. (non modular)bricks in foundation and plinth in: (i) (1 Cem: 4 Kanhaighat C/Sand) |
| 113 | Half brick masonry with Ist class common burnt clay F.P.S. (non modular) bricks in foundation and plinth : (i) cement mortar 1:4 (1 cement : 4Local Kanhaighat coarse sand) |
| 114 | 15 mm cement plaster 1:3 (1 cement: 3 Kanhaighat coarse sand) finished with afloating coat of neat cement on the roughside of single or half brick wall. |
| 115 | Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms. |
| 116 | Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms |
| 117 | Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : (i) W.C. pan with ISI marked white solid plastic seat and lid. |
| 118 | Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make,including painting of fittings and brackets, cutting and making good the walls wherever required:- (a) (a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass |
| 119 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :(a) 15 mm nominal bore |
| 120 | P/F Brass full way valve with C.I. wheel (screwed end) (i) 25mm dia. |
| 121 | (ii) 32mm dia. |
| 122 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete |
| 123 | P/F C.I. Cover with frame (for manhole and chambers) (i) 600 mm x 450 mm (heavy duty) (38 Kg) |
| 124 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. (a) External Works.(i) 32mm dia. nominal outer dia Pipes |
| 125 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.(A) Internal Concealed work, including cutting chases and making good the wall etc.(i) 15 mm nominal outer dia Pipes |
| 126 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. (a) External Works.(i) 80mm dia. nominal outer dia Pipes |
| 127 | (iv) G/S 20 KL with Overhead Tank - 2 nos. |
| 128 | Earthwork in excavation foundation trenches or drains including dressing of sides and ramming of bottoms and including getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50 m. (a) Lift upto 1.5 m. ( a ) Hard/Dense soil. |
| 129 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm.in depth, consolidating each deposited layer by ramming and watering lead upto 50 metres lift upto 1.5 metre. |
| 130 | Providing and laying cement concrete works in foundation and plinth excluding the cost of centering & shuttering in (a) C.C. 1:3:6 (1 cement :3 kanhaighat coarse sand :6 graded stone aggrt. 40mm nominal size). |
| 131 | Providing and laying cement concrete works in foundation and plinth excluding the cost of centering & shuttering in (a) C.C. 1:2:4 (1 cement :2 kanhaighat coarse sand :4 graded stone aggrt. 40mm nominal size). |
| 132 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns,pillars, piers, abutments, posts and struts etc. up to floor five level,excluding cost of centering, shuttering, finishing and reinforcement :(a)1:1.5:3 (1 cement :1.5 coarse sand:3 graded stone aggregate 20 mm nominal size.) |
| 133 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement :1.5 coarse sand:3 graded stone aggregate 20 mm nominal size.) |
| 134 | Steel reinforcement for R.C.C. work including straightening, cutting,bending, placing in position and binding all complete.(a)Thermo-Mechanically Treated bars. |
| 135 | Providing form work i/c centering & shuttering so as to give a rough finish strutting and propping etc. height of propping and centering below supporting floor to ceiling not exceeding 4m and removal of the same for insitu reinforced concrete to and plain concrete work in. (using 12mm shuttering ply)(a) Foundation footings, bases of columns etc. and mass concrete. |
| 136 | Columns, pillars, posts and struts (square, rectangular or polygon in plan). |
| 137 | (b) Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof ply 12mm thick |
| 138 | Suspended floor, roofs landings and the like (i) floors etc. upto 200mm in thickness. |
| 139 | Edges of slab and breaks in floors and walls (i) Under 20cm wide |
| 140 | P/F C.I. Cover with frame (for manhole and chambers) (a) 600mm x450mm (heavy duty)(38 Kg) |
| 141 | Brick work with 1st class common burnt clay F.P.S. (non modular) bricks in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 kanhaighat coarse sand) |
| 142 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1cement :4 coarse sand) |
| 143 | 12mm cement plaster 1:4 (1 cement : 4 coarse sand). |
| 144 | 15mm cement plaster 1:4 (1 cement : 4 coarse sand). |
| 145 | 15 mm cement plaster 1:3(1 cement:3 kanhaighat coarse sand)finished with a floating coat of neat cement. |
| 146 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. (a) External Works.(i) 32mm dia. nominal outer dia Pipes |
| 147 | P/F Brass full way valve with C.I. wheel (screwed end) (i) 25mm dia. |
| 148 | Applying one coat of cement primer of approved quality on wall surface. |
| 149 | Finishing walls with textured exterior paint of required shade : (i) New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including base coat of water proofing cement paint applied @ 2.20kg/10 sqm. |
| 150 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 151 | Steel work welded in built up section/framed work including cutting,hoisting,fixing in position and applying a priming coatof approved steel primer using steel etc. as required.(a) In grating,frames,guard bar,railing,brackets,gates and similar works. |
| 152 | (v) Providing IEI |
| 153 | Wiring for light point/fan point/exhaust fan point/call bell point with 1.5mm2 FR PVC insulated copper conductor single core cable in PVC cassing capping with modular type switch, modular plate, suitable size GI-box and earthing the point with 1.5mm2 FR PVC insulated copper conductor single core cable etc.as reqd. |
| 154 | Group A |
| 155 | Group B |
| 156 | Group C |
| 157 | Wiring for light point/power plug with 2X4mm2 FR PVC insulated copper conductor single core cable in PVC cassing capping along with 1 No. 4mm2 FR PVC insulated copper conductor single core cable for loop earthing etc.as reqd. |
| 158 | Wiring for circuit/Sub-main wiring with earth wire with (the following sizes of) FR PVC ins.cu.cond single core cable in PVC cassing capping etc.as reqd. |
| 159 | 2X1.5mm2+1X1.5mm2 earth wire |
| 160 | 2X2.5mm2+1X2.5mm2 earth wire |
| 161 | 2X4mm2+1X4mm2 earth wire |
| 162 | 2X10mm2+1X10mm2 earth wire |
| 163 | Supply and fixing (following modular type switch/socket) on the existing switch box/cover i/c connection etc as reqd. |
| 164 | 5/6 amps switch |
| 165 | 15/16 amps switch |
| 166 | 3 pin 5/6 amps socket outlet |
| 167 | 6 pin 15/16 amps socket outlet |
| 168 | S/F 25 amp Air-Conditioner power plug point i/c modules metal box on surface or in recess 4-modules plate and cover in front, 25 amp modular starter 25 amp modular socket outlet and 25 amp plug i/c connection etc as reqd. |
| 169 | P/L 50mm2 four core pvc ins.(heavy duty) Al. cond. armoured cable of 1.IKV grade in size not exceedng 25mm2 direct in ground i/c excavation, sand cushioning protective covering and refilling the trench etc.as reqd. |
| 170 | S/F brass batten/angle holder i/c connection etc.as reqd. |
| 171 | S/F 12W LED bulb |
| 172 | SITC surface mounted LED Down Lighter with white powder coated Al. housing with integrated electronic driver 15 W 840 LHEAAGP6IA2W012 complete with connection as rqd. (Havell's) |
| 173 | S/F fan hook i/c bolt & nuts. |
| 174 | S/F 48\\"sweep (1200mm) AC ceiling fan complete with down rod,canopy, 3 (three) bladesetc.as reqd. (Make Bajaj/Usha/Crompton/Orient) |
| 175 | S/F stepped type electronic fan regulator on the existing modular plate sewitch box i/c connection but excluding modular plate etc. |
| 176 | Installation of exhaust fan upto 450mm sweep in the existing opening i/c making the hole to suit the size of the above fan, making good the damaged, connection testing commissioning etc. as reqd. |
| 177 | S/F 305mm sweep exhaust fan complete with accessories i/c connection etc. as reqd. |
| 178 | S/F call bell/buzzer suitable for DC/AC single phase 230V complete as reqd. |
| 179 | S/F bell push modular type complete as reqd. |
| 180 | SITC 50W LED 5000K energy saving IP 65 Flood Light luminaries with high power LED as light source Havell's JETACOMPECTOFL50W LED 757LTG complete with connection as rqd. (Havell's) |
| 181 | S/F 1.5 ton 5 stars inverter service split air conditioner with stabilizer in built including all accessories for maximum separation of 5 mts and connection as reqd. Make Samsung, Model No. AR18TV5PAWK. |
| 182 | Design, supply, installation testing and commissioning of L.T.Panel board of dust and vermin proof mounted with thickness of 16 SWG metal clad sheet with suitable for use at 3- Phase, 4 pole,50 Hz 415V fitted with the following switch gears of four way outgoing conforming to IS/IEC:60947-2, HSN Code 8537 :- |
| 183 | 1. 200 amp. TPN on load changeover switch - 1 No. |
| 184 | 2. 200 amp. TPN bus bar chamber - 1 No. |
| 185 | 3. 125 amp. TPN thermal adjustable MCCB - 4 Nos. |
| 186 | 4. Prewired module Ammeter, voltmeter with selector switch and indicator lamp (Digital) |
| 187 | S/F wall/floor mounted metal board of welded constn.fabricated with minimum 50mm X 50mm X6mm angle iron frame work with horizontal and vertical intermediate members of suitable angle/flat iron for mounting of switch gear i/c painting etc. |
| 188 | P/F 125 amp. TPN stand ground on load change over switch (Compact design) 415/500V including connection etc as reqd. |
| 189 | S/F bus bar chamber with 4 strips copper bus bar length 300mm suitable for 100 amp capacity complete with all accessories i/c connection earthing the body etc.as reqd. |
| 190 | S/F (following way) single pole and nuetral, sheet steel MCCB distributuion board, 240V on surface/recessed complete with tinned copper bus bar neutral bus bar, earth bar,din bar, hinged front sacrylic cover for the MCCB knobs detachable gland plate, interconnection, phosphatized and powder painted i/c earthing etc as reqd (but without MCB/RCCB/Isolator) (a) 2+4 way |
| 191 | S/F 5 amp to 32 amp rating 230V 'B' series MCB for lighting and other load of (following poles) in the existing MCB DB complete with connection testing and commissioning etc.as reqd. (a) Single pole |
| 192 | (a)10 amp MCB \\"C\\" Curve |
| 193 | (a)20 amp MCB \\"C\\" Curve |
| 194 | Supplying & fixing (following rating) double pole 240V isolator in existing MCB DB complete with connection testing & commissioning as reqd. (a) 40 amp |
| 195 | P/F 300x450x60mm(n/size) with permissible variation of plus minus 5mm in size wooden board complete with locking arrangement and painting etc. |
| 196 | Earthing with copper plate 600x600x6mm thick i/c accessories and providing masonary enclosure with copper plate having locking arrangement and watering pipes etc.(but without charcoal and salt complete as reqd.) |
| 197 | Extra for charcoal and salt for G.I.plates or copper plate earth electrode as reqd. |
| 198 | P/F 4.06mm dia.copper wire on surface or in recess for loop earthing etc.as reqd. |
| 199 | Supply, Installation,Testing & Commissioning of solar LED Street lamp All-in -One with in built SCC system wattage of 30W of make Crompton Greaves ltd code no. CSADEMP25/30CDL,140 Lumen/Watt high efficiency crystaline solar SPV panel and G.I. Tubular/Octagonal pole of 6 mt high including connection and muffing in RCC 1:3:6(1 cemt: 3 c/sand: 6 stone aggrt of 40 mm n/size) including centering, shutturing, earth work etc. as reqd. |
| 200 | S/F swaged type steel tubular pole 8 mt.long as per 410-SP-14 conforming to IS-2713 (Pt-II) 1980 with bracket in cement concrete 1:3:6 (1 cem.:3 c/sand : 6 gr. St. 40mm n/size) foundation i/c excavation and refilling etc. as reqd. |
| 201 | S/F L.T. cross arm 50X50X6mm - 2 wires |
| 202 | S/F back clamp for L.T. pole |
| 203 | S/F stay set complete with stay wire & stay insulator etc.as reqd. |
| 204 | Supply and drawing of AB cable of size (3x50+1x35)mm2 |
| 205 | Supplying & installation of dry powder(Stored Pressure) fire extinguisher suitable for fires involving combustible lide wood, paper, cloth etc. capacity: 4 kg (ISI marked). |
| 206 | Supplying & installation of carbon dioxide type fire extinguisher suitable for fires involving materials like oil, electric & delicate machineries) capacity: 4.5 kg (ISI marked). Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 24, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 30, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 2 daysJul 30, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 2 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender