Tender For Repair / Maintenance Of Sewage Pumps And Panels And Cleaning Of Sewage Ug Sumps And Installations And Allied Works In Army Area Jodhpur As Per Cpp Ser No 32
Tender Value
49 Lakhs
Estimated cost
Bid Submission
20 Aug 2026
5 days left
EMD
98000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jodhpur → Rajasthan
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repair / Maintenance Of Sewage Pumps And Panels And Cleaning Of Sewage Ug Sumps And Installations And Allied Works In Army Area Jodhpur As Per Cpp Ser No 32
Corrigendum
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 13-Aug-2026 | Bid Auto Extn Corrigendum | Bid Auto Extn Corrigendum | 20-Aug-2026 |
BOQ
| Sl. No. | Item Description |
| 1 | Lifting/ lowering of non clog sewage submersible pump set of the capacity 225 cum/hr, head 20 meter speed 1450 RPM Model No KRTK 150-315/234 UG1-S make KSB from the Raw Sewage sump of depth 40 feet_Lifting : Disconnection of outgoing delivery mains and eletrical connection from the panel and dewatering the STP main receiving sump with in the time period for easy working and should be provide suitable pumps for lifting of raw sewage water from 40 ft depth, pumps out let should be connected with existing header, after dewatering, lifting of unserviceable non clog sewage submersible pump set of any depth alongwith column pipe/ without column pipe, SWR rope including existing submersible cable and check the unserviceability,remove the sludge/ poly bags/ cement bags/any solid items from inside the pump bowel/impellor and make good working condition with all safetyes etc complete all as directed. Lowering :- Lowering the non clog sewage submersible pump after making operational condition alongwith column pipe/ without column pipe, SWR rope including existing submersible cable and all respective items here-in- above lifting and installation of pump motor in its original position, connections the as well as delivery main including electrical connectiion of both end i.e. with starter and motor terminals. Note :- Maint/break down work should be rectify at the earliest otherthan delay may be penalised Rs:1500/- per/Hour. |
| 2 | Cutting and taking out existing burnt out/unserviceable copper winding from the stator unit of non clog sewage submersible pump set Cleaning of slots and complete stator unit with using carbon tetra chloride (CTC Solution)/standers cleaner Material and labour for rewinding the motor with 'F' class super enamelled copper wire of existing size/gauge including providing bi-metallic thermal overload protection and all necessary insulating materials such as varnish, insulating paper, sleev, seal etc for 28 HP motor. |
| 3 | Supply and fixing of bearing to above make motor & pump |
| 4 | Supply and fixing of oil seal |
| 5 | Supply and fixing of Impeller stainless steel |
| 6 | Supply and fixing of Bearing sleeve |
| 7 | Supply and fixing of Hexagon head bolt |
| 8 | Supply and fixing of Cable duct with oil seal complete set |
| 9 | Supply and fixing of Screw and Head bolt |
| 10 | Material and labour for colling oil for Motor (ISO VG 68) |
| 11 | Material and Labour for repairing and servicing /cleaning complete of non clog sewage submersible pump set of the capacity 225 cum/hr, head 20 meter, speed 1450 RPM Model No KRTK 150-315/234 UG1-S make KSB with replacement of worn out /unserviceable parts and reassembling the same after complete repair with accessories such as nut, bolts, washers etc. Installation with proper alignment including testing, commissioning and all external part painted complete to the entire satisfaction of Engr-in-charge. Note:- All spare parts as required for repair/overhauling shall be measured and paid separately under relevant item of Schedule 'A' and the spares should be suitable to as per existing make and model number. |
| 12 | Taking out Air cooled twin lobe type UR-1150H V- belt driven air compressors complete with electric motor of capacity 60 HP from the foundation, opening of suction filter , suction silencer, V-pulley for machine, V-pulley for electric motor, V- belts, V- belts guard, safety valve (spring loaded type), NRV and pressure gauge etc and carrying out servicing to the blowers, pump with motor . |
| 13 | Supply and fixing of Air filter complete set for 60 hp air blower |
| 14 | Supply and fixing of V-belts as per existing |
| 15 | Supply and fixing of Air release safety valve suitable size |
| 16 | Supply and fixing of Pressure gauge as per existing |
| 17 | Material and labour for Engine/compressors oil |
| 18 | All as per item serial No. 4 here in above but capacity of compresser is suitable for 7.5 HP motor. |
| 19 | Taking out old unserviceable compressor motor of any make any type from sewage pump house and Material and labour for replacement of suitable bearings and rewinding comprising disconnection/ isolation of electric motor and transporting from site to repair work shop, dismantling, stripping out and removing old burnt winding wire, cleaning of slots etc. Rewinding complete with super enamelled copper winding wire of appropriate gauge including all necessary insulation material class-I, varnishing and heating as per requirment. Re-installing in position and reassembling the same after complete repair with accessories such as nut, bolts, washers etc. Installation with proper alignment including testing, commissioning complete to the entire satisfaction of Engr-in-charge of capacity of 60 HP electric motors 440 V 3 phase. |
| 20 | All as item serial no 11 but motor of capacity 7.5 HP Motor 440 V 3 phase |
| 21 | Lifting/ lowering of non clog sewage submersible pump / monoblock pump set of the capacity 3 HP to 12.5 HP from the sewage pump houses , arboriculture sumps & eco lake Lifting : Disconnection of outgoing delivery mains and eletrical connection from the panel and lifting of unserviceable non clog sewage submersible pump set of any depth alongwith column pipe, SWR rope including existing submersible cable and check the unserviceability,remove the sludge/ poly bags/ cement bags/any solid items from inside the pump bowel/impellor and make good working condition with all safetyes etc complete all as directed. Lowering :- Lowering the non clog sewage submersible pump after making operational condition alongwith column pipe, SWR rope including existing submersible cable and all respective items here-in- above lifting and installation of pump motor in its original position, connections the as well as delivery main including electrical connectiion of both end i.e. with starter and motor terminals. Note :- Note :- (a) Rate quoted against items deemed to be included for lifting /lowering. delay may be penalised Rs: 1500/- per/hour. |
| 22 | Material and Labour for repairing and servicing /cleaning complete of submersible pump set of the capacity 3.0,7.5 ,10.0 &12.5 HP with replacement of worn out /unserviceable parts and reassembling the same after complete repair with accessories such as nut, bolts, washers etc. Installation with proper alignment including testing, commissioning and all external part painted complete to the entire satisfaction of Engr-in-charge. Note:- All spare parts as required for repair/overhauling shall be measured and paid separately under relevant item of Schedule 'A' and the spares should be suitable to as per existing make and model No. |
| 23 | Cutting and taking out existing burnt out/unserviceable copper winding from the stator unit of non clog sewage submersible pump set Cleaning of slots and complete stator unit with using carbon tetra chloride (CTC Solution). Material and labour for rewinding the motor with 'F' class super enamelled copper wire of existing size/gauge including providing bi-metallic thermal overload protection and all necessary insulating materials such as varnish, insulating paper, sleev, seal etc for the capacity of 7.5 HP motor. |
| 24 | Cutting and taking out existing burnt out/unserviceable copper winding from the stator unit of non clog sewage submersible pump set Cleaning of slots and complete stator unit with using carbon tetra chloride (CTC Solution). Material and labour for rewinding the motor with 'F' class super enamelled copper wire of existing size/gauge including providing bi-metallic thermal overload protection and all necessary insulating materials such as varnish, insulating paper, sleev, seal etc for the capacity of 10 HP motor. |
| 25 | Cutting and taking out existing burnt out/unserviceable copper winding from the stator unit of non clog sewage submersible pump set Cleaning of slots and complete stator unit with using carbon tetra chloride (CTC Solution). Material and labour for rewinding the motor with 'F' class super enamelled copper wire of existing size/gauge including providing bi-metallic thermal overload protection and all necessary insulating materials such as varnish, insulating paper, sleev, seal etc for the capacity of 12.5 HP motor. |
| 26 | Supply and fixing of Bearing suitable to 7.5 hp, 10 hp & 12.5 hp. As per existing pump & motor |
| 27 | Supply and fixing of Oil seal suitable to 7.5 hp, 10 hp & 12.5 hp. As per existing pump & motor |
| 28 | Supply and fixing of Impeller stainless steel suitable to 7.5 hp, 10 hp & 12.5 hp. As per existing pump & motor |
| 29 | Supply and fixing of Impeller wear ring suitable to 7.5 hp, 10 hp & 12.5 hp. As per existing pump & motor |
| 30 | Supply and fixing of Bearing sleeve suitable to 7.5 hp, 10 hp & 12.5 hp. As per existing pump & motor |
| 31 | Supply and fixing of Cable duct suitable to 7.5 hp, 10 hp & 12.5 hp. As per existing pump & motor |
| 32 | Material and labour for colling oil for Motor (ISO VG 68) |
| 33 | Taking out old leaked/unserviceable butterfly valves of size 40, 50, 80 mm, 100, 150 ,200 and 250 mm from various location in Sewage Treatment plant, Sewage pump houses complete all as directed by EIC. |
| 34 | Suppy and install 50mm dia butterfly valve (wafer type) PN-1.6 with SS-304 Disc with standard case flaged type lever operated of confirming to IS-13095 complete. |
| 35 | Suppy and install 80mm dia butterfly valve (wafer type) PN-1.6 with SS-304 Disc with standard case flaged type lever operated of confirming to IS-13095 complete. |
| 36 | Suppy and install 100mm dia butterfly valve (wafer type) PN-1.6 with SS-304 Disc with standard case flaged type lever operated of confirming to IS-13095 complete. |
| 37 | Suppy and install 150mm dia butterfly valve (wafer type) PN-1.6 with SS-304 Disc with standard case flaged type lever operated of confirming to IS-13095 complete. |
| 38 | Suppy and install 200mm dia butterfly valve (wafer type) PN-1.6 with SS-304 Disc with standard case flaged type gear operated of confirming to IS-13095 complete. |
| 39 | M & L for Excavation in trenches not exc 1.5m width and n. exc 1.5m in depth and getting out for laying of pipes etc in any type of soil. |
| 40 | M & L for Returning filling in incl spreading levelling watering and well ramming in layers n.exc 25cm in any type of soil. |
| 41 | M & L for Removing excavated material n.exc 50m and depositing where directed at a level n. exc 1.5m above starting point. |
| 42 | Supply and fixing of PVC heavy duty flexible hose pipe of size 40mm dia |
| 43 | Supply and fixing of PVC heavy duty flexible hose pipe of size 50mm dia |
| 44 | Taking down existing old unserviceable cable of any size and in replacement supply, laying flexible flat PVC insulated PVC sheathed copper couductor stranded submersible cable,1100 volts grade 2.5 Sqmm 3 core including jointing material and connection work. |
| 45 | Taking down existing old unserviceable cable of any size and in replacement supply, laying flexible flat PVC insulated PVC sheathed copper couductor stranded submersible cable,1100 volts grade 4 Sqmm 3 core including jointing material and connection work. |
| 46 | Taking down existing old unserviceable cable of any size and in replacement supply, laying flexible flat PVC insulated PVC sheathed copper couductor stranded submersible cable,1100 volts grade 6 Sqmm 3 core including jointing material and connection work. |
| 47 | Taking down existing old unserviceable cable of any size and in replacement supply, laying flexible flat PVC insulated PVC sheathed copper couductor stranded submersible cable,1100 volts grade 10 Sqmm 3 core including jointing material and connection work. |
| 48 | Taking out any type, any size MCCB from panel as directed. |
| 49 | supply and fixing of MCCB 32 - 40 amp, 4/3 pole,415Volt, 25 KA including cable lugs of suitable size, complete testing, commissioning complete to the entire satisfaction of Engr-in-charge |
| 50 | supply and fixing of MCCB 63 amp, 4/3 pole,415Volt, 25 KA including cable lugs of suitable size, complete testing, commissioning complete to the entire satisfaction of Engr-in-charge |
| 51 | supply and fixing of MCCB 100 amp, 4/3 pole,415Volt, 25 KA including cable lugs of suitable size, complete testing, commissioning complete to the entire satisfaction of Engr-in-charge |
| 52 | supply and fixing of MCCB 125 amp, 4/3 pole,415Volt, 25 KA including cable lugs of suitable size, complete testing, commissioning complete to the entire satisfaction of Engr-in-charge |
| 53 | supply and fixing of MCCB 160 amp, 4/3 pole,415Volt, 25 KA including cable lugs of suitable size, complete testing, commissioning complete to the entire satisfaction of Engr-in-charge |
| 54 | supply and fixing of MCCB 200 amp, 4/3 pole,415Volt, 25 KA including cable lugs of suitable size, complete testing, commissioning complete to the entire satisfaction of Engr-in-charge |
| 55 | supply and fixing of MCCB 250 amp, 4/3 pole,415Volt, 25 KA including cable lugs of suitable size, complete testing, commissioning complete to the entire satisfaction of Engr-in-charge |
| 56 | Taking out burnt out contactor and in replacement supply and fixing for Power contactor mnx 18 ,415 Volt. , 4/ 3pole, including copper controlcable for internal wiring with pintype/u type/ring type lugs of suitable size,including operating relays to match the operational function of the contactor of the same all as directed and testing on completion of the work complete all as directed by EIC |
| 57 | Taking out burnt out contactor and in replacement supply and fixing for Power contactor mnx 32 ,415 Volt. , 4/ 3pole, including copper controlcable for internal wiring with pintype/u type/ring type lugs of suitable size,including operating relays to match the operational function of the contactor of the same all as directed and testing on completion of the work complete all as directed by EIC |
| 58 | Taking out burnt out contactor and in replacement supply and fixing for Power contactor mnx 40 ,415 Volt. , 4/ 3pole, including copper controlcable for internal wiring with pintype/u type/ring type lugs of suitable size,including operating relays to match the operational function of the contactor of the same all as directed and testing on completion of the work complete all as directed by EIC |
| 59 | Taking out burnt out contactor and in replacement supply and fixing for Power contactor mnx 50 ,415 Volt. , 4/ 3pole, including copper controlcable for internal wiring with pintype/u type/ring type lugs of suitable size,including operating relays to match the operational function of the contactor of the same all as directed and testing on completion of the work complete all as directed by EIC |
| 60 | Taking out burnt out contactor and in replacement supply and fixing for Power contactor mnx 70 ,415 Volt. , 4/ 3pole, including copper controlcable for internal wiring with pintype/u type/ring type lugs of suitable size,including operating relays to match the operational function of the contactor of the same all as directed and testing on completion of the work complete all as directed by EIC |
| 61 | Taking out burnt out contactor and in replacement supply and fixing for Power contactor mnx 90 ,415 Volt. , 4/ 3pole, including copper controlcable for internal wiring with pintype/u type/ring type lugs of suitable size,including operating relays to match the operational function of the contactor of the same all as directed and testing on completion of the work complete all as directed by EIC |
| 62 | Taking out burnt out contactor and in replacement supply and fixing for Power contactor mnx 110 ,415 Volt. , 4/ 3pole, including copper controlcable for internal wiring with pintype/u type/ring type lugs of suitable size,including operating relays to match the operational function of the contactor of the same all as directed and testing on completion of the work complete all as directed by EIC |
| 63 | Supply and fixing in repair of over load relay up to capacity 70 amp making all incoming and outgoing electric connection complete all as specified and directed. |
| 64 | Supply and fixing in repair of Multifunction meter 3 Ph to show pf,kw,kvar,Volt,Amp,F,Kva complete all as directed. |
| 65 | Supply and fixing in repair of VMR relay SM 800 complete all as directed. |
| 66 | Supply and fixing in repair of phase indicator as fitted at site including wiring complete all as directed. |
| 67 | Supply and fixing in repair of Push button switch as fitted at site including wiring complete all as directed. |
| 68 | M & L for spray painting for Lt panel at STP , SPH and eco lake different sizes (Note- rates of paint work included in rate) |
| 69 | Dismantling of unserviceable valves from different locations at sewage plant and in replacement Supply, installation, connecting and testing sluice valve 100 mm dia, ductile iron body (Long Body) Class PN-1.6 with flanged ends drilled suitable for the following bore of pipes, ISI marked (IS : 14846 : 2000), having Stainless Steel/brass spindle with iron wheel at top complete with nuts, bolts, washers, rubber gasket, etc all as specified and directed. |
| 70 | Dismantling of unserviceable valves from different locations at sewage plant and in replacement Supply, installation, connecting and testing sluice valve 150 mm dia, ductile iron body (Long Body) Class PN-1.6 with flanged ends drilled suitable for the following bore of pipes, ISI marked (IS : 14846 : 2000), having Stainless Steel/brass spindle with iron wheel at top complete with nuts, bolts, washers, rubber gasket, etc all as specified and directed. |
| 71 | Dismantling of unserviceable valves from different locations at sewage plant and in replacement Supply, installation, connecting and testing sluice valve 200 mm dia, ductile iron body (Long Body) Class PN-1.6 with flanged ends drilled suitable for the following bore of pipes, ISI marked (IS : 14846 : 2000), having Stainless Steel/brass spindle with iron wheel at top complete with nuts, bolts, washers, rubber gasket, etc all as specified and directed. |
| 72 | Dismantling of unserviceable valves from different locations at sewage plant and in replacement Supply, installation, connecting and testing sluice valve 250 mm dia, ductile iron body (Long Body) Class PN-1.6 with flanged ends drilled suitable for the following bore of pipes, ISI marked (IS : 14846 : 2000), having Stainless Steel/brass spindle with iron wheel at top complete with nuts, bolts, washers, rubber gasket, etc all as specified and directed. |
| 73 | Dismantling of unserviceable valves from different locations at sewage plant and in replacement Supply, installation, connecting and testing sluice valve 300 mm dia, ductile iron body (Long Body) Class PN-1.6 with flanged ends drilled suitable for the following bore of pipes, ISI marked (IS : 14846 : 2000), having Stainless Steel/brass spindle with iron wheel at top complete with nuts, bolts, washers, rubber gasket, etc all as specified and directed. |
| 74 | Taking out unserviceable non return valves from the pumping/distribution of raw/treated water line and removing from the site and in replacement supply, fixing and testing 100mm dia non return valve/reflux valve of 15 Kg/Cm2 body pressure and 10 kg/cm2 seat pressure suitable for 100 mm dia flanged type all as directed. |
| 75 | Taking out unserviceable non return valves from the pumping/distribution of raw/treated water line and removing from the site and in replacement supply, fixing and testing 150mm dia non return valve/reflux valve of 15 Kg/Cm2 body pressure and 10 kg/cm2 seat pressure suitable for 150 mm dia flanged type all as directed. |
| 76 | Taking out unserviceable non return valves from the pumping/distribution of raw/treated water line and removing from the site and in replacement supply, fixing and testing 200mm dia non return valve/reflux valve of 15 Kg/Cm2 body pressure and 10 kg/cm2 seat pressure suitable for 200 mm dia flanged type all as directed. |
| 77 | S & F round strand steel wire rope RHO/LHO/RHL/LHL conforming to IS: 2266/02 dia 15 mm 1770 N/mm² tensile and connected clamp nut bolts fixed complete all as per directed. |
| 78 | Taking out old submersible cable of any shape from the sewage pump to the LT panels and removing from the site and in replacement, supply and fix submersible cable PVC insulated and PVC sheathed multistranded flat copper conductor 7 core 2.5 Sqmm. |
| 79 | Taking out old submersible cable of any shape from the sewage pump to the LT panels and removing from the site and in replacement supply and fix submersible cable PVC insulated and PVC sheathed multistranded flat copper conductor 7 core 4 Sqmm. |
| 80 | Taking out unserviceable LED flood light and in replacement S & F LED flood light 100w 6500k IP66 & surge protection complete all as directed. |
| 81 | Taking out rusted steel sections from the FAB / Clarifier tube settler tanks by removing dual media filters , cutting the existing corroded, weaken portion from the existing welded structure and removing from the site. Supply, fabrication and connecting cross arms, bracings, supports, clamps and back plates fabricated from structural steel sections including nuts, bolts, washers, welding, bending cold or hot, drilling holes for bolts, in any shape or size as indicated or directed and inclusive of one primer coat, one under coat and one finishing coat of water proofing paint coat to the steel surface complete all as directed. |
| 82 | Taking out rusted steel fabricated drum sections from the Clarifier tube settler tanks including thrust bearing, bridge railing complete, moter etc complete all connected items as directed. |
| 83 | Supply and fixing new steel fabricated drum as per existing size made of 10mm thick steel section duly powder coated |
| 84 | Supply and fixing new thrust bearing set complete as per existing all as specified and directed by Engr-in-charge. |
| 85 | Repair and re-fixing existing clarifier bridge with connected all accessories complete as per existing all as specified and directed by Engr-in-charge. |
| 86 | Taking out complete tube setller media from calorifoculator sump carefully and cleaning all as directed by Engr-in-charge. |
| 87 | Dewatering and taking out inside sludge stainers sweeping and taking out sludge in consolidated position from calorifoculater sumps upto depth not exceeding 15 mtr including cleaning of internal wall surface and floor throughly to made it free from dirt by scrubbing and washing accumulated materials with water, including cleaning of floculator and sewage raw water chanels, suction discharge lines. After cleaning the following works should be needful (i) repair/ replacement/welding of damaged scrapper unit and water flow chanels with connected item works. (ii) repair/ replacement of damaged centre flow drum with connected item . (iii) repair of bridge rail leveling, gear box service , oil changing, replace of bearings and V belt as per site required and electric cable connection & functioning. (iv) should be two coat enamel painting of complete iron items of EIC. Note : (a) the contractor should be responsibulity of all safety features during the work ie hand gloves, mask, belt with rope etc and the Job should be done with in sepervision of contractor/ superviser of the contractor. (b)Any kind of risk during this job Deppt will not be responsible.. (c ) Iron & tube settler media was not deemed in the cost and is measured seperately in relevent sch A item. |
| 88 | Re-fixing of tube setller media on calorifoculator sump carefully complete as per existing as directed by Engr-in-charge. |
| 89 | Dewatering ,sweeping and taking out sludge in consolidated position from under ground sumps upto depth not exceeding 15 mtr including cleaning of internal wall surface and floor throughly to made it free from dirt by scrubbing and washing accumulated materials with water, including cleaning of suction lines inside wet sump and removing from site etc complete all as directed at site. Note : (a) the contractor should be responsibulity of all safety features during the work ie hand gloves, mask, belt with rope etc and the Job should be done with in sepervision of contractor/ superviser of the contractor. (b) Any kind of risk during this job Deppt will not be responsible. |
| 90 | Lifting/ lowering of submersible pump set of the capacity 55 LPS, head 45 mtr make KSB from the UG sump/open well of depth 30 feet Lifting : Disconnection of outgoing delivery mains and eletrical connection from the panel and lifting of unserviceable sewage submersible pump set of any depth alongwith column pipe, SWR rope including existing submersible cable and check the unserviceability,remove the sludge/any solid items from inside the pump bowel/impellor and make good working condition with all safetyes etc complete all as directed.Lowering :- Lowering the submersible pump after making operational condition alongwith column pipe, SWR rope including existing submersible cable and all respective items here-in- above lifting and installation of pump motor in its original position, connections the as well as delivery main including electrical connectiion of both end i.e. with starter and motor terminals. |
| 91 | Material and Labour for repairing and servicing /cleaning complete of submersible pump set of the capacity 55 LPS, head 45 meter, speed 1450 RPM,Make KSB with replacement of worn out /unserviceable parts and reassembling the same after complete repair with accessories such as nut, bolts, washers etc. Installation with proper alignment including testing, commissioning with two coats of suitable painting complete to the entire satisfaction of Engr-in-charge. Note:- All spare parts as required for repair/overhauling shall be measured and paid separately under relevant item of Schedule 'A' and the spares should be suitable to as per above refered model & make of KSB. |
| 92 | Cutting and taking out existing burnt out/unserviceable copper winding from the stator unit of submersible pump set Cleaning of slots and complete stator unit with using carbon tetra chloride (CTC Solution). Material and labour for rewinding the motor with 'F' class super enamelled copper wire of existing size/gauge including providing bi-metallic thermal overload protection and all necessary insulating materials such as varnish, insulating paper, sleev etc for 50 HP motor. |
| 93 | Supply and fixing suction cover (Heavy) for 50 hp submersible pump with stainer stainless steel addition as desired as per site requirement complete all as directed by Engr-in-charge. |
| 94 | Supply and fixing Half coupling pump for 50 hp submersible pump with stainer stainless steel addition as desired as per site requirement complete all as directed by Engr-in-charge. |
| 95 | Supply and fixing S.S Shaft (V Stg) for 50 hp submersible pump with stainer stainless steel addition as desired as per site requirement complete all as directed by Engr-in-charge. |
| 96 | Supply and fixing Neck Ring for 50 hp submersible pump with stainer stainless steel addition as desired as per site requirement complete all as directed by Engr-in-charge. |
| 97 | Supply and fixing S.S. Sleeve for 50 hp submersible pump with stainer stainless steel addition as desired as per site requirement complete all as directed by Engr-in-charge. |
| 98 | Supply and fixing coupling for 50 hp submersible pump with stainer stainless steel addition as desired as per site requirement complete all as directed by Engr-in-charge. |
| 99 | Supply and fixing top washer for 50 hp submersible pump with stainer stainless steel addition as desired as per site requirement complete all as directed by Engr-in-charge. |
| 100 | Supply and fixing key for shaft for 50 hp submersible pump with stainer stainless steel addition as desired as per site requirement complete all as directed by Engr-in-charge. |
| 101 | Supply and fixing bowl bush for 50 hp submersible pump with stainer stainless steel addition as desired as per site requirement complete all as directed by Engr-in-charge. |
| 102 | Supply and fixing coupling bush for 50 hp submersible pump with stainer stainless steel addition as desired as per site requirement complete all as directed by Engr-in-charge. |
| 103 | Supply and fixing pump bowl for 50 hp submersible pump with stainer stainless steel addition as desired as per site requirement complete all as directed by Engr-in-charge. |
| 104 | Supply and fixing discharge outlet for 50 hp submersible pump with stainer stainless steel addition as desired as per site requirement complete all as directed by Engr-in-charge. |
| 105 | Supply and fixing impeller for 50 hp submersible pump with stainer stainless steel addition as desired as per site requirement complete all as directed by Engr-in-charge. |
| 106 | M& L for servicing of Mud pump of capacity 5 HP by changing engine oil, air/oil filters and cleaning as per OEM instruction all as per direction of Engineer-in-charge. |
| 107 | M& L for servicing of Mud pump of capacity 15 HP by changing engine oil, air/oil filters and cleaning as per OEM instruction all as per direction of Engineer-in-charge. |
| 108 | M& L for Mud pump of capacity 15 HP by changing impeller, bearing, all types of pipe all as per direction of Engineer-in-charge. |
| 109 | M&L for taking out old unserviseable tyre of trolly mounted mud pump. |
| 110 | Supply and fixing of new tyre of size as per existing including new tube all as specified and directed by Engr-in-charge. |
| 111 | Supply and fixing of PVC heavy duty flexible hose pipe of size 100mm dia |
| 112 | Supply and fixing of male & female connector for PVC heavy duty flexible hose pipe of size 100mm dia |
| 113 | Material and labour for taking out old unserviceable centrifugal motor of any make any type from the treated water sump and for replacement of suitable rewinding comprising disconnection/ isolation of electric motor and transporting from site to repair work shop, dismantling, stripping out and removing old burnt winding wire, cleaning of slots etc. Rewinding complete with super enamelled copper winding wire of appropriate gauge including all necessary insulation material class-I, varnishing and heating as per requirment. Re-installing in position and reassembling the same after complete repair with accessories such as nut, bolts, washers etc. Installation with proper alignment including testing, commissioning complete to the entire satisfaction of Engr-in-charge for the 2/3 HP electric motors 440 V 3 phase capacity. |
| 114 | Material and labour for taking out old unserviceable centrifugal motor of any make any type from the treated water sump and for replacement of suitable rewinding comprising disconnection/ isolation of electric motor and transporting from site to repair work shop, dismantling, stripping out and removing old burnt winding wire, cleaning of slots etc. Rewinding complete with super enamelled copper winding wire of appropriate gauge including all necessary insulation material class-I, varnishing and heating as per requirment. Re-installing in position and reassembling the same after complete repair with accessories such as nut, bolts, washers etc. Installation with proper alignment including testing, commissioning complete to the entire satisfaction of Engr-in-charge for the 5HP electric motors 440 V 3 phase capacity. |
| 115 | Material and labour for taking out old unserviceable centrifugal motor of any make any type from the treated water sump and for replacement of suitable rewinding comprising disconnection/ isolation of electric motor and transporting from site to repair work shop, dismantling, stripping out and removing old burnt winding wire, cleaning of slots etc. Rewinding complete with super enamelled copper winding wire of appropriate gauge including all necessary insulation material class-I, varnishing and heating as per requirment. Re-installing in position and reassembling the same after complete repair with accessories such as nut, bolts, washers etc. Installation with proper alignment including testing, commissioning complete to the entire satisfaction of Engr-in-charge for the 7.5HP electric motors 440 V 3 phase capacity. |
| 116 | Material and labour for taking out old unserviceable centrifugal motor of any make any type from the treated water sump and for replacement of suitable rewinding comprising disconnection/ isolation of electric motor and transporting from site to repair work shop, dismantling, stripping out and removing old burnt winding wire, cleaning of slots etc. Rewinding complete with super enamelled copper winding wire of appropriate gauge including all necessary insulation material class-I, varnishing and heating as per requirment. Re-installing in position and reassembling the same after complete repair with accessories such as nut, bolts, washers etc. Installation with proper alignment including testing, commissioning complete to the entire satisfaction of Engr-in-charge for the 10HP electric motors 440 V 3 phase capacity. |
| 117 | Taking out unserviceable HDPE pipe from the trench includes removing from the site and in replacement supply, laying & testing in trenches high density polyethylene pipes (HDPE) of specification PE-100 PN-10, SDR-11, 100 mm bore conforming to IS 4984 of 2016 with all fittings and fixture such as tee, bend elbow if required to make the services functional complete all as directed . Note : - (a) All fittings like bend ,elbow,tee will be provided by contactor and nothing extra shall be admissible. |
| 118 | All as per serial item No 109 here-in-above but size of pipe 65mm bore. |
| 119 | All as per serial item No 109 here-in-above but size of pipe 50mm bore. |
| 120 | All as per ser item No 109 here-in-above but size of pipe 25mm bore. |
| 121 | Material and labour for taking out old unserviceable centrifugal submersible motor and areatar pump of any make any type from the treated water sump or Eco lake and replacement of suitable rewinding comprising disconnection/ isolation of electric motor and transporting from site to repair work shop, dismantling, stripping out and removing old burnt winding wire, cleaning of slots etc. Rewinding complete with super enamelled copper winding wire of appropriate gauge including all necessary insulation material class-I, varnishing and heating as per requirment. Re-installing in position and reassembling the same after complete repair with accessories such as nut, bolts, washers etc. Installation with proper alignment including testing, commissioning complete to the entire satisfaction of Engr-in-charge of (a) 12.5 HP electric motors 440 V 3 phase. |
| 122 | Material and labour for cleaning of FAB,sweeping and taking out sludge in consolidated position from FAB sump upto depth not exceeding 15 mtr including cleaning of internal wall surface and floor throughly to made it free from dirt by scrubbing and washing accumulated materials with water, including cleaning of suction lines inside wet sump and removing from site etc complete all as directed by Engr-in-charge at site. Note : Necessary safety equipment such as hand gloves, mask belt with rope and other safety items, any kind of risk during lifting of sludge will be solely responsibility of the contractor . |
| 123 | Material and labour for cleaning of CCT tank,sweeping and taking out sludge in consolidated position from CTT tank upto depth not exceeding 5 mtr including cleaning of internal wall surface and floor throughly to made it free from dirt by scrubbing and washing accumulated materials with water, including cleaning of suction lines inside wet sump and removing from site etc complete all as directed by Engr-in-charge at site. Note : Necessary safety equipment such as hand gloves, mask belt with rope and other safety items, any kind of risk during lifting of sludge will be solely responsibility of the contractor . |
| 124 | Material and labour for cleaning of FFT tank,sweeping and taking out sludge in consolidated position from FFT tank upto depth not exceeding 5 mtr including cleaning of internal wall surface and floor throughly to made it free from dirt by scrubbing and washing accumulated materials with water, including cleaning of suction lines inside wet sump and removing from site etc complete all as directed by Engr-in-charge at site. Note : Necessary safety equipment such as hand gloves, mask belt with rope and other safety items, any kind of risk during lifting of sludge will be solely responsibility of the contractor . |
| 125 | Material and labour for cleaning of treated water tank, sweeping and taking out sludge in consolidated position from treated water tank upto depth not exceeding 5 mtr including cleaning of internal wall surface and floor throughly to made it free from dirt by scrubbing and washing accumulated materials with water, including cleaning of suction lines inside wet sump and removing from site etc complete all as directed by Engr-in-charge at site. Note : Necessary safety equipment such as hand gloves, mask belt with rope and other safety items, any kind of risk during lifting of sludge will be solely responsibility of the contractor . |
| 126 | M&L PCC (1:2:4) type B-1 (using 20 mm graded stone aggregate) in support of pipes or foundation of pump complete all as directed. |
| 127 | Material and labour for cutting the road for laying of pipe and repair the same with road repair material (Patch mat) all as directed as site width of road cutting would be 0.45M. |
| 128 | Taking out old unserviceable foot valve and in replacement supply and fix of CI foot valve as per IS and complete are as size 50 mm dia |
| 129 | Taking out old unserviceable foot valve and in replacement supply and fix of CI foot valve as per IS and complete are as size 80 mm dia |
| 130 | M&L for galvanised iron pipe 20mm medium grade (ISI marked) with and including medium grade (ISI marked) fitting concealed or fixed to walls, ceiling or laid in floors including chase cuttings , making good to disturbed surfaces, GI clamps as per Specification and as directed with all fittings including taking down of old unserviceable pipes. |
| 131 | M&L for galvanised iron pipe 25mm medium grade (ISI marked) with and including medium grade (ISI marked) fitting concealed or fixed to walls, ceiling or laid in floors including chase cuttings , making good to disturbed surfaces, GI clamps as per Specification and as directed with all fittings including taking down of old unserviceable pipes. |
| 132 | M&L for galvanised iron pipe 50mm medium grade (ISI marked) with and including medium grade (ISI marked) fitting concealed or fixed to walls, ceiling or laid in floors including chase cuttings , making good to disturbed surfaces, GI clamps as per Specification and as directed with all fittings including taking down of old unserviceable pipes. |
| 133 | M&L for galvanised iron pipe 80mm medium grade (ISI marked) with and including medium grade (ISI marked) fitting concealed or fixed to walls, ceiling or laid in floors including chase cuttings , making good to disturbed surfaces, GI clamps as per Specification and as directed with all fittings including taking down of old unserviceable pipes. |
| 134 | Earthing complete with galvanized steel earth plate electrodes 600x600x6 mm thick buried directly in ground eath (earth pit not less 2.25 m deep below ground level) with top edge of the plate not less then 1.5 mtr below normal ground level connected to galvanized iron earthing strip 32mm x6mm thick by means of bolt nuts check nuts and washers of galvnised iron or steel all as specified & shown in electrical plate No.5 of MES SSR part-I connected to earth test point as specified and testing on completion including provision of 40 mm dia light grade pipe & watering pipe shall be 20 mm bore medium grade including all excavation & earth work in any type of soil incl PCC for pit (1:3:6) type C-1 with RCC cover in PCC(1:2:4) including charcoal , salt funnel GI pipe 40 mm dia light grade up to to 7.5 mtr length ,all as directed at site. |
| 135 | Dismantling of stone massonary valve chamber of any size and pattern and at any position and construction of valve chamber of size 900 x 600 x 1000mm with PCC foundation 1:4:8 type D2 using 40mm graded stone aggregate stone massonary built in cement mortar 1:6 with plastering of 10m thickness internally and 15mm thickness externally above and below grojnd level with PCC 1:2:4 type B1 using 20mm graded stone aggregate incl frame made of angles iron of size matches with the internal size of the valve chamber and chamber cover made of MS sheet of 3.0mm thickness incl MS hinge and painting the steel surfaces with two coats of synthetic enamel paint over a coat of sred oxide primer incl necessary earch work, excavation etc all as specified and directed by Engr-in-Charge. |
| 136 | Dismantling of stone massonary valve chamber of any size and pattern and at any position and construction of valve chamber of size 450 x 450 x 600mm with PCC foundation 1:4:8 type D2 using 40mm graded stone aggregate stone massonary built in cement mortar 1:6 with plastering of 10m thickness internally and 15mm thickness externally above and below grojnd level with PCC 1:2:4 type B1 using 20mm graded stone aggregate incl frame made of angles iron of size matches with the internal size of the valve chamber and chamber cover made of MS sheet of 3.0mm thickness incl MS hinge and painting the steel surfaces with two coats of synthetic enamel paint over a coat of sred oxide primer incl necessary earch work, excavation etc all as specified and directed by Engr-in-Charge. |
| 137 | All as per serial item no 128 above but of size and PCC bolck wall thickness 30 cm |
| 138 | Cleaning of ECO Lake of capacity 100 MLD by draining out water with the pump/motors of any capacity and quantity of water to be draining out to the central sewage line or existing nearby oxidation pond by pumping, the quantity of water to be draining out not less than 75 MLD, sweeping out accumulated sludge,dirt of any kind from the bottom of the lake, scrubbing walls with scrubber applying necessary anti oxident chemicals with proper safety arrangement to the workers . |
| 139 | Testing of STP water for TDS . BOD ,COD, PH , DO, Coliform or as directed by Engr-in-charge at receving inlet from any recognised LAB. |
| 140 | Testing of STP water for TDS . BOD ,COD, PH , DO, Coliform or as directed by Engr-in-charge at secondary treatment from any recognised LAB. |
| 141 | Testing of STP water for TDS . BOD ,COD, PH , DO, Coliform or as directed by Engr-in-charge at tertiary treatment from any recognised LAB. |
| 142 | Taking out burned MCB SPN 32/40 amp and in replacement S & F MCB SPN 32/40 amp, 240v 'B' series complete all as directed. |
| 143 | Taking out burned MCB SP 6 to 20 amp and in replacement S & F MCB SP 6 to 20 amp, 240v 'B' series complete all as directed. |
| 144 | Disconnecting of all electrical connection, M&L for prepraction of old painted surface with the help of paint remover,scrapper & fine ambery paper and painting with two coat of heat resistance paint with the help of spray gun over one coat of red oxide and writing SM No/ Machine No and connect back all electrical connections complete all as specified and directed on following Capicity Pump set (Motor+Pump+ Foundation Frame):- 3 - 5 HP. |
| 145 | Disconnecting of all electrical connection, M&L for prepraction of old painted surface with the help of paint remover,scrapper & fine ambery paper and painting with two coat of heat resistance paint with the help of spray gun over one coat of red oxide and writing SM No/ Machine No and connect back all electrical connections complete all as specified and directed on following Capicity Pump set (Motor+Pump+ Foundation Frame):- 10 - 12 HP, |
| 146 | Disconnecting of all electrical connection, M&L for prepraction of old painted surface with the help of paint remover,scrapper & fine ambery paper and painting with two coat of heat resistance paint with the help of spray gun over one coat of red oxide and writing SM No/ Machine No and connect back all electrical connections complete all as specified and directed on following Capicity Pump set (Motor+Pump+ Foundation Frame):- 50 - 60 HP, |
| 147 | M&L for in repair/rectification of leakage in existing STP rising/delivery DI Pipe Spigot/ socketed end including necessary earth work (i.e. excavation, removal & refilling, of trench), pumping out water from the ditch and rectify the defects by taking out of existing broken rubber ring or pipe hole and the same by using necessary additional rubber ring and iron Clamps detechable joints,leak repair clamp etc including testing, commissioning of DI pipe line complete all as directed. (Iron clamp, rubber ring & other arrangement for rectification of said breakdown is included in the cost of item . for the size of 200 mm bore. |
| 148 | M&L for in repair/rectification of leakage in existing STP rising/delivery DI Pipe Spigot/ socketed end including necessary earth work (i.e. excavation, removal & refilling, of trench), pumping out water from the ditch and rectify the defects by taking out of existing broken rubber ring or pipe hole and the same by using necessary additional rubber ring and iron Clamps detechable joints,leak repair clamp etc including testing, commissioning of DI pipe line complete all as directed. (Iron clamp, rubber ring & other arrangement for rectification of said breakdown is included in the cost of item . for the size of 250 mm bore. |
| 149 | Taking out old unserviceable gate valve and supply and fix new bronze globe valve with iron wheel head screwed both ends for iron pipe and fixed of size of 20 mm dia. |
| 150 | Taking out old unserviceable gate valve and supply and fix new bronze globe valve with iron wheel head screwed both ends for iron pipe and fixed of size of 25 mm dia. |
| 151 | Taking out old unserviceable gate valve and supply and fix new bronze globe valve with iron wheel head screwed both ends for iron pipe and fixed of size of 50 mm dia. |
| 152 | M & L for surface dressing including uprooting bushes/ grass etc all as directed by Engineer Incharge. |
| 153 | M&L for arresting leakge of HDPE pipe by fixing additional HDPE pipe upto 1.5mtr ,socket,tee or bend as per site requirement including earth work, detachable joint, rubber gasket,nut bolt etc as directed for 110/80mm bore pipe.Note :- Work shall be carried out in running condition of supply of water, therefore before undertake the work, requirement of material shall be ascertain, accordingly leakage shall be stopped promptly. |
| 154 | M&L for arresting leakge of HDPE pipe by fixing additional HDPE pipe upto 1.5mtr ,socket,tee or bend as per site requirement including earth work, detachable joint, rubber gasket,nut bolt etc as directed for 63/50mm bore pipe.Note :- Work shall be carried out in running condition of supply of water, therefore before undertake the work, requirement of material shall be ascertain, accordingly leakage shall be stopped promptly. |
| 155 | Taking out old & Supply and fixing, welding whereever required to shape in existing position vertical/horizental , connecting flanged end/welding in length of 3 mtr/6 mtr, MS pipe heavy duty testing after connecting complete all as directedon by inserting of new tees, branches etc all as specified and directed of size of 100 mm Note:- (Tee, joints shall be inclusive in the cost ). |
| 156 | Taking out old & Supply and fixing, welding whereever required to shape in existing position vertical/horizental , connecting flanged end/welding in length of 3 mtr/6 mtr, MS pipe heavy duty testing after connecting complete all as directedon by inserting of new tees, branches etc all as specified and directed of size of 150 mm Note:- (Tee, joints shall be inclusive in the cost ). |
| 157 | Taking out old & Supply and fixing, welding whereever required to shape in existing position vertical/horizental , connecting flanged end/welding in length of 3 mtr/6 mtr, MS pipe heavy duty testing after connecting complete all as directedon by inserting of new tees, branches etc all as specified and directed of size of 200 mm Note:- (Tee, joints shall be inclusive in the cost ). |
| 158 | Taking up raising/ delivery DI sewage water mains 150mm bore (including all fittings), with flanged or spigot and socket end with tyton joints/ gasket with nut bolts & washers of any size and relaying the same with using new gasket / tyton joint complete all as specified and as directed. Note :- During the execution of work if any damage in pipe line cntractor will replace with new pipe without any cost |
| 159 | Taking up raising/ delivery DI sewage water mains 200/250mm bore (including all fittings), with flanged or spigot and socket end with tyton joints/ gasket with nut bolts & washers of any size and relaying the same with using new gasket / tyton joint complete all as specified and as directed. Note :- During the execution of work if any damage in pipe line cntractor will replace with new pipe without any cost |
| 160 | M & L for taking up 250mm cast iron/HDPE/PVC water/sewage treated water mains (including all fittings), with spigot and socket ends and lead joints of any size all as specified and dirercted by Engr-in-Charge of following sizes :-. |
| 161 | Supply and lay 250mm DI pipe (STP treated water) centrifugally cast of class K-7 with spigot and socket ends/flanged end suitable for tyton joints/flanged joints including rubber gasket/rubber ring and other accessories like nut-bolts etc for the following sizes. |
| 162 | Material and labour for fixing DI specials such as bends(any type, radius and angle),tappers any type, (straight, bend, increasing, decreasing or double socket etc) tee pieces single branch, 'Y' junction, double branch, cross (all sockets or socket and spigot) collars, caps & plugs of sizes upto 300mm |
| 163 | Material and labour for cleaning of receiving sump at 0.5MLD STP ,sweeping and taking out sludge in consolidated position from receiving sump upto depth not exceeding 15 mtr including cleaning of internal wall surface and floor throughly to made it free from dirt by scrubbing and washing accumulated materials with water, including cleaning of suction lines inside wet sump and removing from site etc complete all as directed by Engr-in-charge at site. Note : Necessary tool & plant, hydra, JCB, safety equipment such as hand gloves, mask belt with rope and other safety items, any kind of risk during lifting of sludge will be solely responsibility of the contractor. Maint/break down work should be rectify at the earliest otherthan delay may be penalised Rs:1500/Hour. |
| 164 | Material and labour for cleaning of receiving sump at 9.5MLD STP ,sweeping and taking out sludge in consolidated position from receiving sump upto depth not exceeding 25 mtr including cleaning of internal wall surface and floor throughly to made it free from dirt by scrubbing and washing accumulated materials with water, including cleaning of suction lines inside wet sump and removing from site etc complete all as directed by Engr-in-charge at site. Note : Necessary tool & plant, hydra, JCB, safety equipment such as hand gloves, mask belt with rope and other safety items, any kind of risk during lifting of sludge will be solely responsibility of the contractor. Arrangement to stop seawage water pipeline 600mm dia and make temporary bypass pumping system. Maint/break down work should be rectify at the earliest otherthan delay may be penalised Rs:2500/Hour. |
| 165 | M&L for provision of sloped roof covered shed not less than 4.0 mtr height and covering area 7.0 mtr x 7.0 mtr for preventing out door equipment from rainfall/unwanted damage etc, shed to be fabricated out of steel structural sections, i.e. 80mm dia medium grade gi pie for vertical supports (8 nos) firmly grovoted two feet deep with 1:3:6 PCC work, and 50x50x5mm angle iron for horizontal supports and roof using Aluminium sheer thickness not less than 0.5mm thickness including necessary cutting, drilling, bending hot or cold, welding, suitable size of nut, bolt, 'J' hook and washers etc as required at site all as specified and directed by Engr-in-charge. |
| 166 | M&L for provision of sloped roof covered shed not less than 3.0 mtr height and covering area 4.0 mtr x 3.0 mtr for preventing out door equipment from rainfall/unwanted damage etc, shed to be fabricated out of steel structural sections, i.e. 50mm dia medium grade gi pie for vertical supports (4 nos) firmly grovoted two feet deep with 1:3:6 PCC work, and 50x50x5mm angle iron for horizontal supports and roof using Aluminium sheer thickness not less than 0.5mm thickness including necessary cutting, drilling, bending hot or cold, welding, suitable size of nut, bolt, 'J' hook and washers etc as required at site all as specified and directed by Engr-in-charge.Note - The contract sum shall be calculated by deducting the amount shown in Credit Schedule attached to this tender, from total amount of Schedule 'A'/BOQ. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 13, 2026
11:30 IST
Tender Published
Tender notice published.
Completed
Aug 20, 2026
18:00 IST
Corrigendum-1 Issued
Clarifications on tender conditions and amendments issued.
Upcoming · 5 daysAug 20, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 5 daysAug 22, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 7 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender