Tender For Work Of Installing Borewells At Various Locations In The Municipal Council Area
Tender Value
32.79 Lakhs
Estimated cost
Bid Submission
31 Jul 2026
0 days left
EMD
65580
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jaipur → Rajasthan
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Work Of Installing Borewells At Various Locations In The Municipal Council Area
BOQ
| Sl. No. | Item Description |
| 1 | Construction of tube-well from ground levels to accommodatehousing and assembly pipe of following sizes in all types of alluviumstrata by percussion/ rotary drilling method and with gravel as perIS:4097-1967 and packing as per IS:2800 (Part I -& II) 1979 asamended upto date (the work includes the cost of gravel & itsprimary packing and packing during development, lowering ofhousing & strainer assembly pipes, with supply and wrapping of coirrope, wherever necessary for arresting fine sand particles. The workwill not include cost of housing pipe and strainer pipe assembly anddevelopment work, but work would be completed after obtainingsand free water).Nominal bore 150mm dia |
| 2 | Construction of Tube-well upto 100 Meter depth and above in alltype of rocks by DTH system and over burden to accommodatecasing pipe of following sizes in all types of soils and over burdenincluding lowering of casing pipes but excluding cost of casing pipesas per IS : 2800 (Part I & II) 1979 specifications. The work would becompleted after obtaining sand free water. The tube well shouldhave a throughout bore as per nominal dia of casing pipe:150 mm dia Nominal bore |
| 3 | Supply of ERW M.S. black casing pipe ISI marked (IS: 4270/1992)of grade Fe410 of following nominal bore sizes at site of work.150 mm dia |
| 4 | Supply and fixing of M.S. clamp set of 50 ×6mm flat iron with nuts and bolts etc. for holding the riser pipe assembly of submersible pump set. |
| 5 | Development of tube well as per IS specification using suitable compressor to give sand free water for required yield of the gravel packed tube well. |
| 6 | Supply and fixing of tube well cover of M.S. sheet (6mm thick) withnuts and bolts complete for casing size:150 mm dia |
| 7 | P/Laying ISI marked P.V.C. insulated submersible cable confirmingto(IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire shouldbe made from 99.90 % purity copper, stranding in acc. toIS:8130/IEC 60228 for lower watt loss , oxygen free for lesschances of oxidization, insulation PVC type A/C/D , flame retardantas per IS 10810-53, better amperage rating as per IS:3961 part 5,existing pipe / open trench / Cable tray / on surface including makingconnection etc. as required. For additional technical parameters ofproduct / work refer Annexure 'A' attached with this BSR |
| 8 | Providing & Fixing of HDPE pipe Confirming to IS:4984:2021 forwater supply suitable for submersible & jet pump with requiredfittings ie socket, elbows, tee etc. complete in all respect. All as perpre approved by Engineer in-charge. For additional technicalparameters of products/ work , refer Annexure \\"A\\" attached withthis BSR .40 mm OD 6 kg / cm2 |
| 9 | SITC of Radial / mixed flow ISI marked water and anti-corrosiveliquid filled submersible motor pump sets suitable for 100/150mmdia borewell. The size of adopter fixed on top of the motor shouldexceed the top of coupler , for safegaurd the coupler. Theconstruction material of motor and pump should match IS: 8034 :2018 and IS: 9283 guideline. The radial flow pumpset shouldoperate at 5 star energy efficiency level of BEE and mixed flowpump set should operate at 3 star energy level of BEE,accompained by valid BEE certificate. Motor should be IE2 class asper IEC 60034-2-1: 2007, IEC 60034-30: 2008, & IS12615:2011with required accessories including making connection suitable forBore well. The job includes labour part of lowering of riser pipe G.I./H.D.P.E. with rope, cables & pump, installation of complete fittingand accessories, jointing of electrical cables up to Starter. All labourfor testing of submersible pumps set and supply of water to watermains, complete in all respect. OEM shall have submit NABL / CPRI/ ERDA accrediated lab type test certificate before execution. Allas per pre approved by Engineer in-charge. For additional technicalparameters of products/ work , refer Annexure \\"A\\" attached withthis BSR .100 mm diameter Submersible pump shall have following HPRating, phase, Head range, Discharge range respectively.5.0 HP, 1-Ø, (56 - 236)Mtr, (90 - 25) LPM Copper wound |
| 10 | SITC of Contactor OEM Fabricated DOL/Star-Delta Starter panelwith switchgear selection as per Type-2 Cordinatiom Chart andmade out from 1.6 mm thick powder coated CRCA sheet, enclosurecomprising of over load protection relay, short circuit & singlephasing protection, Illuminated ON / OFF push buttons, ammeter,voltmeter, indicating lamps etc. suitable for following rating motorscomplete in all respect. All as per pre approved by Engineer incharge. For additional technical parameters of products/ work ,refer Annexure \\"A\\" attached with this BSR .For single phase Submersible / Monoblock pump . 3.0 HP to 5.0 HP ( DOL starter ) |
| 11 | Providing and fixing 3 layer PP-R (Poly propylene Randomcopolymer) pipes SDR 7.4 U V stabilized & anti - microbial fusionwelded, having thermal stability for hot & cold water supply includingall PP - R plain & brass threaded polypropylene random fittings i/cfixing the pipe with clamps at 1.00 m spacing. This includes testingof joints complete as per direction of Engineer in-charge.Internal work - Exposed on wall PN - 16 Pipe, 25 mm OD |
| 12 | Providing & Fixing in position, MS fabrication work using angles, sqrtubes, c channels etc for various partition frame as per Design &Instructions & Complete in all aspects . including all materials labour,finishing etc complete |
| 13 | Providing and fixing PTMT bib cock of approved quality and colour.15mm nominal bore, 86 mm long. Weighing not less than 88 gms. |
| 14 | Providing & Laying of Polypropylene rope Confirming to IS:5175 forsubmersible pump of following sizes. complete in all respect. All asper pre approved by Engineer in-charge. For additional technicalparameters of products/ work , refer Annexure \\"A\\" attached withthis BSR .12mm (suitable up to 50 mm OD pipe) Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 23, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 31, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
TodayAug 03, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 3 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender