Tender For Provn Of 01 X Single Offr Accn At Officer Transit Facility Ch Awat Under Mil Stn Pithoragarh
Tender Value
34.80 Lakhs
Estimated cost
Bid Submission
13 Aug 2026
16 days left
EMD
69600
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Champawat → Uttarakhand
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Provn Of 01 X Single Offr Accn At Officer Transit Facility Ch Awat Under Mil Stn Pithoragarh
BOQ
| Sl. No. | Item Description |
| 1 | Surface excavation n exc 30 cm deep and averaging 15 cm and getting out in any type of soil complete all as specified. |
| 2 | Excavating over areas, n exc 1.5m deep and getting out in any type of soil complete all as specified and directed. |
| 3 | Excavation in trenches n exc 1.5m wide and n exc 1.50m in depth for foundation etc and getting out in any type of soil, complete all as specified and directed by Engineer-In- Charge. |
| 4 | Excavation in trenches in soft/lose soil n.exc. 1.5M wide & n exc 1.5M deep for laying of GI/CI pipe line & getting out including forming bottom surface all as specified and directed. |
| 5 | Excavation in trenches n.exc 1.5 mtr wide and n.exc 1.5 mtr in depth and getting out Soft/disintegrated rock complete all as specified and as directed |
| 6 | Returning filling in, incl spreading levelling watering and well ramming in layers n exc 25cm (after the pipes have been laid and tested) in anhy type of soil complete all as specified and directed by Engineer-In- Charge. |
| 7 | Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm in hard/ dense soil all as spd and directed |
| 8 | M&L for sand filling in trenches for cushioning of cable complete all as specified and directed. |
| 9 | Removing excavated material soil n.exc 50 m and depositing where directed at a level n.exc 1.5 mtr above the starting point all as directed. |
| 10 | Removing excavated material exceeding 250M but not exc 500m and depositing where directed. Complete all as specified and directed by Engineer-In- Charge. |
| 11 | M&L for hand packing (any thickness) at back of walls with broken stone or boulders and raising (or lowering) to the required level complete all as specified and directed. |
| 12 | M&L for hardcore broken stone boulders broken to guage n exec 63 mm all as spd and directed. |
| 13 | M&L for Treating the bottom and sides of excavation at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and as directed. |
| 14 | M&L for Treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured) |
| 15 | M&L for Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specifiedf and as directed |
| 16 | M&L for Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specifiedf and as directed |
| 17 | M&L for Treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall |
| 18 | M &L PCC 1:4:8 type D-2 (using 40 mm graded stone aggregate) as in foundation filling and mass concrete, coping of pole etc complete all as specified and directed. |
| 19 | M&L PCC 1:3:6 type C-2 (using 40mm graded stone aggregate) as in foundation of pole, stays etc. complete all as specified and as directed. |
| 20 | M/L PCC 1:3:6 type C2 ( using 40 mm graded stone aggragate) as in surface channel drain. Complete all as specified and directed |
| 21 | M&L PCC 1:2:4 type B-2 using 20mm graded stone aggregates as in foundation, posts filling and mass concrete complete all as specified and directed by Engineer-in-Charge. |
| 22 | M & L PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in coping including weathering, throating and necessary form work complete all as specified and directed. |
| 23 | M & L for Precast cement concrete block masonry with solid blocks, exc. 10 cm in width and setting in mortar, complete (Set in cement mortar 1:6) (Precast cement concrete) (Type C1 1:3:6 (20mm graded stone aggregate)) |
| 24 | M & L for providing precast cement concrete bonders (for stone walling) type B1 (1:2:4) using 20 mm graded stone aggregate, set in cement mortar 1:4 complete all as specified and directed. |
| 25 | M&L for providing pre cast RCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in cover slab and man hole covers etc complete all as specified and directed by Engineer-In- Charge. |
| 26 | M&L for PCC 1:2:4 type B-1 with 20 mm graded aggregate for coping of pole complete all as directed. |
| 27 | M&L RCC M-25 (Design Mix) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete, complete all as specified and as directed |
| 28 | M&L RCC M-25 (Design Mix) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed |
| 29 | M&L RCC M-25 (Design Mix) Beams, cantilevers, bressummers, lintels over 1.5m span, complete all as specified and as directed |
| 30 | M&L RCC M-25 (Design Mix) as in Columns, pillars, piers, posts and struts complete all as specified and as directed |
| 31 | Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete using extra cement, including forms, moulds mitred/ stoped ends etc. |
| 32 | Supply only liquid water proofing compound complete all as specified and directed by Engineer-In- Charge. |
| 33 | M&L for brick work with old size bricks, straight or curved on plan exc. 6m mean radius, built in CM (1:6) complete all as specified and directed. |
| 34 | M&L for brick work with sub class ‘B’ bricks straight or curved on plan in CM 1:4 as in half brick thick walls complete all as specified and as directed |
| 35 | M&L for brick work with old size full brick th in Honey comb wall, brick subclass ‘B’ burnt clay bricks, straight or curved on plan exc 6m mean radius, built in CM (1:4) complete all as specified and directed. |
| 36 | M & L for cutting chases, pinning in brick/PCC blocks wall in making good to facings where required and pointing in cement mortar 1:3 and cutting chases for concealed water tubing etc and making good complete all as specified and as directed |
| 37 | Material and labour for Bricks common burnt clay building bricks, sub-class ‘B’ designation 75 for protection of UG LT cable all as specified. |
| 38 | M&L for stone masonry walling of random rubble uncoursed, well bonded, bedded and solidly hearted built in CM 1:4 complete all as specified and as directed. |
| 39 | Extra over stone walling for hammer dressing with maximum depression on face form straight edge held against the surface n.exc 40mm in lime or sand stone dressing to face stone and dressing of face beds and joints of random rubble walling complete all as specified and directed. |
| 40 | M & L 16 to 18 mm thick granite (colour as approved by GE) stone slab machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing as in kitchen platform/dado/skirting /platform counter top WHB including cutting holes for oval shape /urinal partitions, door/window cills etc. including 20 mm thick cement screed bed 1:6 CM in horizontal or vertical surfaces including grinding the edges half round and polishing complete all as specified and directed by Engineer-In- Charge. |
| 41 | M&L Formwork (rough finished surface) to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) |
| 42 | M&L for formwork (rough finished surface) to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams;and similar work; vertical or to batter for rough finished surface |
| 43 | M&L Formwork (rough finished surface) to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers,lintels, antilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. |
| 44 | M&L for formwork (rough finished surface) to sides of pillars, posts, struts, piers, columns and stanchions square/rectangular for rough finished surface complete all as specified and as directed. |
| 45 | M&L for Formwork (rough finished surface) to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide complete all as specified and as directed. |
| 46 | S&F IInd class hard wood, 30mm thick skeleton shutters open rebated & prepared to receive, glass, gauge etc. (without sash bars), edge of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass etc, size of members of shutters as specified in Part I, Section 8, clause 8.24(a); supplied and fitted to chowkahts. Complete all as specified and directed. |
| 47 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid laminated door/ window/ Ceosetory windows & other Frames/ Chowkhat single or double rebate of size 125X65mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof,water/ moisture proof and fire retardant, and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. |
| 48 | S&F Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter (laminated both sides) of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture, proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter incl supply and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer- In- Charge. |
| 49 | S&F Aluminium annodised barrel tower bolt of extruded section and fixed 200 mm size with bright bolt complete all as specified and directed. |
| 50 | S & F 250mm Aluminium alloy anodised sliding door bolts with hasp,staple(bolt type)and fixing clips of sheet,cast or extruded section and fixing bolts and sliding bolts of extruded section or aluminium alloy and fixed. |
| 51 | S&F Butt hinges of size 100mm, heavy weight, cold rolled mild steel, and fixed complete all as specified and as directed. |
| 52 | S&F, aluminium handles 150mm size, cast type, anodised complete all as specified and directed. |
| 53 | S&F 150mm long floor door stopper of aluminum alloy body and tongue , anodized with hard drawn steel spring complete all as specified and directed |
| 54 | S&F door closer (aluminium extruded body) hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and as directed. |
| 55 | S&F galvanised mild steel wire cloth 0.56 mm nomonal dia of bar and 1.18 mm avrage width of aperture ,fixed with tined tacks or galvanised wire staples complete all as specified and as directed. |
| 56 | M&L mild steel TMT bars 10mm dia and over, cut to length, bent to shape required incl cranking, bending spirally for hoping for columns hooking ends and bindind with ms wire (annealed) not less than 0.9mm dia or securing with clips all as specified. |
| 57 | All as per item No. 56 here in before but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified and as directed. |
| 58 | S&F powder coated anodised aluminium window and ventilator shutters (powder coating of any colour, thickness or powder coating not less than 50 micron)Three track windows, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1no.) complete all as specified. |
| 59 | Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) windows (3 Track / Openable) for frame/ shutters /track of windows & ventilators, partitions etc including providing and fixing hinges/ pivots/roller incl fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per the directions of Engineer-in-charge |
| 60 | Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and as directed. |
| 61 | M&L 75mm thick PCC 1:3:6 type C-2, (20 mm graded stone aggregate)as plinth protection and finishing even and smooth without using extra cement incl making joints 12 mm wide of full depth of PCC at every 3 meters and at every change in direction and filling the same with sealing compund grade 'A' incl necessary formwork. Complete all as specified and directed. |
| 62 | M&L for PCC 75 mm thick 1:4:8 type D-2 (using 40 mm graded stone aggregate) as in sub base of floors, footings etc, complete all as specified and directed. |
| 63 | M & L for 25 mm thick PCC 1:2:4 type B-0, using 12.5 mm graded stone aggregate as in floors, to receive surface of tile complete all as specified and directed. |
| 64 | M & L, Glazed ceramic tiles in vertical surface 350x 250x 7mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10 mm thick rendering in CM1:4 set & jointed in neat cement slurry & pointed in coloured cement to match ,complete all as specified and directed. |
| 65 | M & L, non skid joint free coloured ceramic tiles 7 to 8 mm thick (Square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 Sqm, over and including 15 mm thick screed bed in CM 1:6 as in floor etc set & jointed in neat cement slurry and pointed in coloured cement to match the shade, including dismantling tile complete all as specified and directed |
| 66 | M&L Chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement and pigment including 15mm screed bed in CM 1:6, complete all as specefied |
| 67 | M&L for 15mm thick rendering on fair faces of brick/ concrete surfaces in CM 1:4 finished even and fair. Complete all as specified and directed. |
| 68 | M&L for rendering 5mm thick on fair faces of brick work or concrete surfaces. Complete all as specified and directed. |
| 69 | M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1 : 4 mixed with water proofing compound finished even and smooth without using extra cement complete all as specified and directed by Engineer-In- Charge. (Water proofing compound shall be measure and paid separatelly). |
| 70 | M&L for 15mm thick rendering in cement mortar 1:6 to on brick masonary wall surfaces or on other than fair faces of brick masonary finished even and fair without using extra cement, complete all as specified and directed. |
| 71 | M&L for Raised pointing to random or polygonal rubble, uncoursed or brought upto courses in CM 1:3 complete all as specified and as directed. |
| 72 | M&L for preparing new plastered surfaces of walls and applying two coats of Oil bound distemper on walls over a coat of primer, complete all as specified. |
| 73 | M&L for preparing new plastered ceiling surfaces and applying two coats of Oil bound distemper over a coat of primer, complete all as specified. |
| 74 | Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces. Complete all as specified and directed. |
| 75 | S&F sheet glass ordinary quality 4mm thick and glazing with oil putty or fixed with bead/ glazing pins in squares n.exc. 0.5 sqm each pane all corner of glass to be fixed with silicon complete all as specified and directed. |
| 76 | S & F GI tubing 40 mm dia light grade in protection of cable of difference dia laid in trench under road/foot path or fixed on pole with necessary clamps with bolts etc all as directed. |
| 77 | Supply and fix GI tubing 20mm dia , medium grade, ISI marked complete with all fittings, laid in trenches or laid under floors, fixed on walls with and providing clamps etc (including short length) complete all as specified & directed. |
| 78 | S&F tubes medium grade galvanized with all fittings & fixed complete to walls & ceiling or laid in floors 32 mm dia bore pipe (including in short length) complete all as specified and as directed |
| 79 | M&L for Cutting of GI Pipes line 40mm dia and reducing to required length before laying in position for insertion of new tees, branches etc complete all as specified & directed. |
| 80 | Supplying and laying of CPVC pipes (outer dia 20 mm) SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified. |
| 81 | S&F CPVC brass elbow for CPVC pipe size 20 mm complete all as specified and as directed. |
| 82 | S&F 500 litre capacity rotational moulded polythylene water storage tanks (cylindrical vertical with closed top ) hoisted and fixed in position, complete all as specified and directed. |
| 83 | S&F bib tap long body fancy type cast copper alloy chromium plated quarter turn handle screwed down screwed for iron pipe or brass ferrule or fixed for 15 mm dia bore pipe complete all as specified and as directed |
| 84 | S & F Brass CP wall mixer 15 mm bore (wall mounted type three way) for mixing hot and cold water screwed down for iron pipe and fixed complete all as specified and as directed |
| 85 | S & F 15 mm dia chromium plated angle cocks/stop valves, brass, screwed down, high pressure with crutch or butterfly handle, flench screwed both ends for iron pipe or for union complete all as specified & directed. |
| 86 | S&F Gun metal globe or gate valves with iron wheel head screwed both ends for iron pipe 20 mm bore and fixed as in repair complete all as specified and as directed |
| 87 | S&F 20mm ball brass valve, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed etc complete all as specified and as directed |
| 88 | S&F PVC connection of 45 cm length including brass nuts complete all as specified and as directed |
| 89 | S&F PVC (SWR) pipes 75 mm bore dia single socketed, in any length with rubber ring joints, laid in trenches or in floors or for weep holes |
| 90 | S&F in repairs, 110mm bore PVC(SWR) pipes single socketed , in any length with rubber ring joints, laid in trenches or in floors and vertical surfaces complete all as specified and directed. |
| 91 | S&F PVC (SWR) door bends 75 mm size any radius complete all as specified and as directed. |
| 92 | S&F PVC (SWR) bends, reducers 110 mm size any radius complete all as specified and as directed. |
| 93 | S & F PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and as directed. |
| 94 | S & F PVC (SWR) vent cowl size 75 mm complete all as specified and as directed. |
| 95 | S&f PVC (SWR) 'P’ trap 110 mm size complete all as specified and as directed. |
| 96 | S&F PVC (SWR) floor trap (outlet dia 75 mm ), plain with grating including jointing with solvent cement complete all as specified and as directed. |
| 97 | M & L for cement concrete 1:3:6 type C-2 for 150 mm dia in concrete bed to drain pipes including packing under and haunching against the sides of pipes etc complete all as specified and directed by Engineer-In- Charge |
| 98 | M & L for Salt-glazed stoneware drain pipes laid in trenches and jointed as specified complete all as specified and directed by Engineer-In- Charge. |
| 99 | S&F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect. Complete all as specified and directed. |
| 100 | S & F fancy type 125mm size square brass CP shower rose with or without swivel joints complete all as specified and as directed. |
| 101 | S&F Toilet paper holder with flat recessed type stainless steel Complete all as specified and directed. |
| 102 | S&F 600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cupwashers, Complete all as specified and directed. |
| 103 | Material and labour for XLPE insulated armoured heavy duty electric cable with aluminium conductor 1100 volts grade with cross sectional area 6 Sqmm, 2 core complete all as specified and as directed. |
| 104 | Material and labour for XLPE insulated armoured heavy duty electric cable with aluminium conductor 1100 volts grade with cross sectional area 16 Sqmm, 2 core complete all as specified and as directed. |
| 105 | Supply and fixing Energy saving & Enviroment friendly LED street light fittings made out of out door type, high pressure die cast anodized alluminium housing with Polycarbonate or Flat Glass Optical cover , system power equal or not less than 60 watt with corroision resistant including thermal management in multiple optics complete with IP 65/66 protection including street light bracket made out of 50 mm light grade GI tubing minimum 3 mtr long with suitable adapter to suit the opening of street light on one end alongwith integrated fabricated adapter round cup type with 4 Nos studs on outer side to fix the bracket on top of existing steel tubular pole one way,with necessary MS clamps with one coat of red oxide and two coats of aluminium paint upon fabricated adapter including nut, bolt, washers complete as specified and directed by engineer –in- charge. all as specified and direcetd. |
| 106 | Material and labour for point wiring for one light controlled by one way switch with 1.5 Sqmm PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable 1100 Volts grade drawn through and including rigid non metallic PVC concealed conduit (medium grade) of suitable dia along with 1.5 sqmm continuous PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable for earth continuity wire, connected to earth dolly and to be terminated in and including modular plate and modular sunken box for mounting switches, sockets, fan regulators etc including testing on completion complete including cutting chases for concealed conduit pinning in making good to facing and pointing in using cement mortar 1:3 and making good disturbed surface all as specified and as directed for one light point controlled by one switch. |
| 107 | All as per item No-106 here -in- before but for ceilinfg fan point controlled by one switch |
| 108 | All as per item No-106 here -in- before but for exhaust fan point controlled by one switch |
| 109 | All as per item No-106 here -in- before but for One 3 Pin, 05 /06 Amps socket outlet point on same board controlled by one, one way 5/06 Amps switch |
| 110 | All as per item No-106 here -in- before but forOne 3 pin, 05 /06 Amps socket outlet point on independent board controlled by one , one way 05/06 Amps switch |
| 111 | All as per serial item No 106 here in before but with 4 Sqmm nominal cross sectional area copper conductor cable for one 15 Amps socket outlet point on independent board with and including continuous earth wire of size 4 Sqmm nominal cross sectional area, single core, PVC insulated copper conductor cable, sheathed and connected to common earth and earth dolly complete all as specified and directed |
| 112 | Supply and fix in repairs factory made epoxy powder coated Distribution board SPN 12 ways (SPN MCB DB) with metal door (IP-43 protection) fabricated from minimum 1.6mm thick CRCA sheet and fixed flush to wall and suitable for universal mounting and including 200 Amp copper tinted bus bar, neutral bar, standard DIN rail, Earth bar and cable ties for cale management, top and bottom removable gland plates with Knockouts and suitable for one SPN/DP-MCB as incomer and SP MCBs outgoing complete all as specified and confirming to IS : 8623. |
| 113 | Material & labour for earthing complete with galvanised mild steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground (earth pit not less than 2.25mtr deep below ground level) with top edge of the plate not less than 1.5mtr below normal ground level steel earth plate connected with GI wire 04mm dia by means of lug, bolts, nuts, check nuts, washers of galvanised iron or steel GI protection pipe 15mm bore light grade all as shown in elect plate No.5 of part I connecting to main switch board / Main DB’s including excavation, earth work, salt and charcoal dust mixed and packed 150mm thick around GI earth plate, GI pipe medium grade 20mm nominal bore watering pipe GI sheet funnel wire mesh, concrete pit, RCC cover in PCC 1:2:4 type B1 duly reinforced with MS Bars 6mm dia at the rate of 150mm center to center both way with suitable lifting handle and pit / chamber in PCC 1:3:6 type C1 , Angle iron 40x40x5mm frame for pit cover including testing on completion complete all as specified and directed.Note- After completion of work if desired test result is not obtained the earthing to be redone with out any extra cost of department. |
| 114 | Supply and fix earting continuity conductor or main earting lead fixed to wall or batten or recess or chases or buried in ground or drawn in conduit pipe or fixed to pole or any other indicated situation for loop earthing as required 4mm dia galvanised iron or steel complete all specified and directed. |
| 115 | Supply install testing and commissioning of 1200mm sweep 230 volts AC ceiling fan ,rating confirming to IS 374:2019, 3 blade down rods, electronic regulator and accessories,min air delivery 210 CFM with service value 6.0 BEE , five star rated with brushless direct current motor (BLDC) including making connection with three core 1.5sqmm flexible copper cable upto ceiling rose complete including taking down old unserviceable ceiling fan and deposited to MES store yard all as directed. Make: Crompton model Entrust 50/ Havells model SS 390 metallic or equivalent in Usha/Bajaj |
| 116 | S&F Exhaust Fan PVC body, 250mm sweep, single phase, 230 volts 50 Hz AC,1400 RPM, energy saving, heavy duty totally enclosed, heavy duty motor with die-cast aluminiun rotor mounted on two ball bearings complete with louvers and shutters including cutting hole for fixing exhaust fan to wall and making good the disturbed surfaces (including making holes in wall,plastering, necessary brickwork and distempering) to match with the existing specification, connecting electrically using 3 core 0.75 Sq mm PVC insulated flexible copper conductor cable over all sheathed all as required at site and as directed. |
| 117 | Supply install and tesing water heater storage type (Geyser) single phase 230 V, 50 Hz, 5 star energy saving high density PUF insulation tank made of heavy duty mangesium anode rod with steel core to protect enamelled tank from rust & corrosion, vertical installation type 25 Ltr Cap 2000 Watt rated power, incoloy 800 glass coated heating element, inner tank coating of feroglas powder, tank made of ultra thick super cold rolled steel plates, rated pressure 0.8 MPa, IPX4 protection consist of safety valves, thermal cut off, thermostat, digital display and adjustable knob for setting of temperature. The temperature range 25 to 75 degreecelsius including connecting up and fixing arrangement on wall including providing hole fastners-04 Nos hot and cold water metallic flexible pipes 15 mm bore of adequate length as provided by OEM or required at site - 02 Nos non return valve 01 No and including necessary plumbing work, complete with intergated PRCD shock safe plug with all protection features as per OEM design and standard all as specified and directed. |
| 118 | Supply & fixing(in repair) MCB, SP, AC, 240 volts of 06 to 32 Amps capacity 10KA, 'C' series and making connections with suitable size of copper lugs complete all as specified & directed. |
| 119 | Supply & fixing(in repair) MCB, SPN, AC, 240 volts of 40 to 63 Amps capacity 10KA, 'C' series and making connections with suitable size of copper lugs complete all as specified & directed. |
| 120 | Material and labour for 2.5 Sqmm 3 core PVC heavy duty electric service cable with copper conductor 1100 volts grade complete all as specified and directed. |
| 121 | Supply and fixing of steel tubular swaged poles with two coat of aluminium paint ovar a coat of red oxide zinc chrome prime in externally exposed to view portion and black bituminous painting to intenal surface and portion embeded in concrete incl making five alternative strips 30 cm wide in different colour above ground level or plinth level incl marking of MES pole No in black paint complete with cast iron base plate, final tapper plug, bolts, nuts and screws as specified type 410 SP-31 (9.00 mtr long) and all as specified. |
| 122 | Supply and fix in replacement of Tube light fitting integrated type suitable for LED 20W indoor decorative aluminium extruded T5 LED batten complete with hosing with all accessories pre wired and making connection with three core copper flexible cable of size 23/0.0076 from ceiling rose to PVC connection to light fitting complete all as specified and directed. |
| 123 | Supply and fix in replacement of Tube light fitting integrated type suitable for LED 10W indoor decorative aluminium extruded T5 LED batten complete with hosing with all accessories pre wired and making connection with three core copper flexible cable of size 23/0.0076 from ceiling rose to PVC connection to light fitting complete all as specified and directed. |
| 124 | Supply & fixing switch modular flush type, 05/06 Amps single pole , one way 240 volts complete all as specified.. |
| 125 | Supply & fixing switch modular type, 15 /16 Amps single pole, one way 240 volts complete all as specified . |
| 126 | Supply & fixing modular outlet 3 pin, 05/06 Amps (2 -in-1 Multipurpose) flush type 240 volts complete all as specified. |
| 127 | Supply & fixing of modular outlet 3 pin, 15/16 Amps (2 -in-1 Multipurpose) flush type 240 volts complete all as specified. |
| 128 | Supply & fixing of ceiling rose surface bakelite 65x 50mm three terminals complete all as specified. |
| 129 | M & L for glazed vitrified tiles (GVT) 7 to 8 mm thick (square/ rectangular) of size 600 x 600 mm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match incl screed bed or bedding layer of mortar, 15 mm thick, in cement mortar 1:6,complete all as specified and directed. |
| 130 | M & L for glazed vitrified tiles (GVT) 7 to 8 mm thick (square/ rectangular) as in Skirting, riser etc (length of tiles not less than 600 mm) set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10 mm thick rendering in CM 1:4 complete all as specified and directed, |
| 131 | S&F coloured Aluminium Composite Panels (ACP) of interior grade for partitions,kitchen cabinet frame work, including necessary sealing. The composite panel should consist of 3mm thermoplastic core of LDPE sandwiched between 2 skins of 0.25mm thick aluminium sheet (alloy designation 310S) making a total panel thickness of 3mm, the sheet shall be fixed using GI brackets/stainless steel bolts and nuts/ screws etc complete with spring washers and cap nuts and all other necessary accessories all hardware shall corrosion resistant frame out of anodised aluminium member.Complete all as specified and directed |
| 132 | S&F PVC boards 18 mm thick any colour as in cabinets incl shelves, shutters and framework, fixed with screws and adhessive as per direction of Engr-in-Charge and manufacturer's instructions including piano hinges, magnet catcher, handles etc. |
| 133 | S&F stainless steel (Grade SS 202) decorative curtain rod of 25 mm bore incl fancy type brackets and finials.complete all as specified and as directed |
| 134 | S&F Oval type Wash Hand Basin (Counter Top) superior quality 550 x 400 mm size fitted over granite slab incl waste pipe coupling 150mm long complete all as specified and directed. |
| 135 | S&F Brass CP wash basin mixer (Long nose Elbow Operated)15mm bore dia for mixing Hot or Cold water screwed down for iron pipe and fixed all as specified and as directed. |
| 136 | S & F vitreous china wash down water closet (One piece) vortex flushing, white, including plastic seat cover and flushing pipe complete all as specified & directed. |
| 137 | M & L for water proofing treatment to non-accessible roof slab with APP based madified polymeric membrane as per manufacturers instructions with following course of description below:-(a) Applying a priming coat of bituminous primer @ 0.30 kg / sqm, till the surface is properly impregnated.(b) Providing APP based 5 layer polymeric membrane minimum weighing 3.6 kg / sqm and minimum 3 mm thick reinforced with polyester non-woven fabric (weight not less than 150 gms /sqm) centre core, laid on primed surface Fixed with hot molten bitumen of grade 85/25 @ 1.2 Kg / Sqm by forced applications as per manufacturers instructions with side over lap of 100 mm and end overlap of 150 mm. All overlap joints shall be sealed thoroughly by thermo fusing both the membrane layer (torching overlap by propane or butane gas torch) and sealing it with the help of hot trowel. The overlap joints shall be made as a monolithic layer. (c) Apply two coat of bituminous aluminium paint @ 0.20 Kg / Sqm over APP membrane. |
| 138 | M & L for junction box hot press moulded SMC of inside dimension size 250 x200x 100 mm and outside dimention 295 x 255 x 120 mm with locking arrangements consisting of necessary suitable arrangements for incoming & out going cables with cable glands & having aluminium bus bar 4 strips of 20x3mm for TPN on necessary epoxy base insulator and fixing of 6 Amp MCB SPN, including necessary 25x3mm flat iron clamps with nuts, bolts & washers all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 23, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 13, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 16 daysAug 20, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 23 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender