Tender For Construction of 352 Multi Storeyed Two Bedroom Apartments Adjoining Pocket-3, Sector-19B, Dwarka, Ph-Ii.Sub Head : Shade Work, Distempering & White Wash Of Remaining Areas, Stone Work And Connection Of Remaining Pvc Pipes Etc. At Mig Housi
Tender Value
28.54 Lakhs
Estimated cost
Bid Submission
30 Jul 2026
7 days left
EMD
57083
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Delhi → Delhi
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Construction of 352 Multi Storeyed Two Bedroom Apartments Adjoining Pocket-3, Sector-19B, Dwarka, Ph-Ii.Sub Head : Shade Work, Distempering & White Wash Of Remaining Areas, Stone Work And Connection Of Remaining Pvc Pipes Etc. At Mig Housing Sector-19B, Dwarka.Estimated Cost : 28,54,140/-
BOQ
| Sl. No. | Item Description |
| 1 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.(i) Single socketed pipes. (a) 110 mm diameter |
| 2 | Providing & fixing UV stabilised fiberglass reinforced plastic sheet roofing up to any pitch, including fixing with polymer coated ‘J’ or ‘L’ hooks, bolts & nuts 8 mm dia. G.I plain/bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovigs incorporating minimum 0.3% ultra-violet stabiliser in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall conform to IS 10192 and IS 12866.The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified.(a) 4 mm thick corrugated. |
| 3 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. (a) Hot finished seamless type tubes |
| 4 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 5 | Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.(a) 1.00 mm thick with zinc coating not less than 275 gm/m2 |
| 6 | Providing and applying 2.5 mm thick road marking strips (retro- reflective) of specified shade/ colour using hot thermoplastic material by fully/ semi automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour, T&P, cleaning the road surface of all dirt, seals, oil, grease and foreign material etc. complete as per direction of Engineer-in-charge and accordance with applicable specifications. |
| 7 | Providing and fixing wire mesh of opening size 75x25 mm or other suitable size including Cutting, Welding complete as per direction of Engineer-in-Charge. |
| 8 | Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications:(a) Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture |
| 9 | Distempering with 1st quality acrylic distemper (ready mixed) having VOC (Volatile Organic Compound) content less than 50 gram / litre, of approved brand and manufacturer including applying additional coats wherever required to achieve even shade and colour.(a) Old work (one or more coats) |
| 10 | White washing with lime to give an even shade:(a) Old work (two or more coats) |
| 11 | Providing and fixing panic bar / latch (Double point) fitted with a single body, Trim Latch & Lock on back side of the Panic Latch of reputed brand and manufacture to be approved by the Engineer-in-charge, all complete. |
| 12 | Providing and fixing heavy duty fire rated SS Door Closer, of make Yale/ Hafele/ Dorma or equivalent, as approved by the Engineer-in-charge. |
| 13 | Providing and fixing Yale/ Hafele/ Dorma or equivalent make fire rated D type SS pull handle of adequate size & as approved by the Engineer-in-charge. |
| 14 | Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to 1S: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters.(a) 80x1.25 mm M.S. laths with 1.25 mm thick top cover |
| 15 | Providing and fixing ball bearing for rolling shutters. |
| 16 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.(a) 25 mm nominal dia Pipes |
| 17 | Providing and Fixing of CPVC Brass FTA of size 40x40 mm compleate as per direction of Engineer-in-Charge. |
| 18 | Providing and Fixing of CPVC Ball Valve of 25 mm dia compleate as per direction of Engineer-in-Charge. |
| 19 | Providing and Fixing of Brass Compression Fitting of 25 mm dia compleate as per direction of Engineer-in-Charge. |
| 20 | Providing and Fixing of Brass Compression Fitting of 32 mm dia compleate as per direction of Engineer-in-Charge. |
| 21 | Providing and Fixing of CPVC Brass FTA of size 50x40 mm compleate as per direction of Engineer-in-Charge. |
| 22 | Providing and Fixing of CPVC Red Bush of size 40x32 mm compleate as per direction of Engineer-in-Charge. |
| 23 | Providing and fixing Black & Yellow PVC/Plastic heavy duty speed breaker/hump of size 350x250x50 mm with both side reflector having weight of each plate not less than 4 kg/m and including nails and adhesive complete as per direction of Engineer-in-Charge. |
| 24 | Providing and fixing sheet covering over expansion joints with iron screws as per design.(a) Non-asbestos 6 mm thick fibre cement board, Type-A, Category-lll as per 1S:14862:2000(i) 400 mm wide |
| 25 | Providing and fixing sheet covering over expansion joints with iron screws as per design.(a) Aluminium fluted strips 3.15 mm thick.(i) 400 mm wide |
| 26 | Providing and fixing Road Safety Convex Mirror of size 80 cm complete as per direction of Engineer-in-Charge. |
| 27 | Amount after applying 0.973 Multiplying Factor due to decrease in GST Rate i.e. on Rs. 29,35,983.00 |
| 28 | Add Cost Index (-) 0.09% i.e. on Rs.28,56,711.00 Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 22, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 30, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 7 daysJul 31, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 8 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender