Tender For Civil Interiors, Furnishing, And Accessories For Shifting Of Silchar Indane Divisional Office To Moinarbond Depot
Tender Value
Ref. Documents
Estimated cost
Bid Submission
29 Jul 2026
6 days left
EMD
Ref. Documents
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Cachar → Assam
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Civil Interiors, Furnishing, And Accessories For Shifting Of Silchar Indane Divisional Office To Moinarbond Depot
BOQ
| Sl. No. | Item Description |
| 1 | CIVIL AND SANITARY WORKS - TOILET ROOM I |
| 2 | Providing and laying Brick work with common burnt clay F.P.S (non Modular) bricks of class designation 7.5 in foundation & plinth |
| 3 | xii) Extra for providing and placing in position 2 Nos. 6mm dia. M.S. bars at every third course of half brick masonry |
| 4 | Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level |
| 5 | ii) RCC 1 Cement :1½ Coarse Sand: 3 Graded Stone Aggregate 20mm |
| 6 | Supply of Steel reinforcement for R.C.C. including straightening, cutting, bending, placing in position and binding all complete at all levels |
| 7 | ii) Thermo Mechanically Treated Bars of Fe- 500D grade or more, conforming to IS1786 |
| 8 | Providing and laying cement plaster on surfaces with Coarse sand including curing etc. |
| 9 | iii) 15mm cement plaster of mix 1:4 (1 cement: 4 coarse sand) on rough side of half or single brick wall |
| 10 | Providing and laying cement plaster on surfaces with fine sand including curing etc. |
| 11 | ii)12 mm cement plaster of mix 1:6 (1 cement: 6 fine sand) |
| 12 | Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10mm and down gauge) including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design in 75x75 mm deep chase |
| 13 | Providing & laying water proofing treatment in sunken portion of WCs, bathroom etc. by applying cement slurry mixed with water proofing cement compound consisting of applying : a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment & sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. |
| 14 | Providing & laying Ceramic Glazed floor tiles 300x300 mm or more (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours White, Ivory, Grey, Fume Red Brown, laid on 20mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand) jointing with grey cement slurry@ 3.3kg/sqm including pointing the joints with white cement and matching pigments etc. complete. |
| 15 | Providing & fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (minimum thickness of 5 mm) of approved make in all colours,shades except burgundy,bottle green,black of any size as approved by Engineer-in-Charge in skirting,risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade. |
| 16 | Finishing walls with water proofing cement paint of required shade with Two or more coats applied @ 3.84 kg/10 sqm: |
| 17 | Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I.cover with frame of 300 x300 mm size(inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design : |
| 18 | i) 100x100 mm size P type with common burnt clay bricks of class Designation 7.5 |
| 19 | Providing and fixing 100 mm sand cast Iron grating for gully trap. |
| 20 | Providing and fixing 3 layer PP-R (Poly propylene Random copolymer pipes confirming to IS 15801, UV stabilized & anti-microbial fusion welded, having thermal stability for hot & cold water supply, including all PP - R plain & brass threaded polypropylene random fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes testing of joints complete as/direction of Engg in Charge. Internal work – Exposed on wall |
| 21 | i) PN - 16 Pipe, 16 mm OD (SDR-7.4) |
| 22 | ii) PN - 16 Pipe, 20 mm OD (SDR-7.4) |
| 23 | Providing and fixing controlled flush, low level cistern made of vitreous china with all fittings complete. |
| 24 | i) 10 litre (full flush) capacity-white |
| 25 | Providing and fixing G.I. inlet connection for flush pipe connecting with W.C. pan. |
| 26 | WC (wall mounted) with fittings |
| 27 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required : |
| 28 | i) White Vitreous China Wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps |
| 29 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.Concealed work including cutting chases and making good the walls etc. |
| 30 | i) 15 mm nominal outer dia Pipes |
| 31 | ii) 20 mm nominal outer dia Pipes |
| 32 | iii) 25 mm nominal outer dia Pipes |
| 33 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS:13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion, Single socketed pipes. |
| 34 | i) 75 mm diameter |
| 35 | ii) 110 mm diameter |
| 36 | Providing & fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS:13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion. |
| 37 | ix) 87.5° Bend of 75 mm |
| 38 | x) 87.5° Bend of 110 mm |
| 39 | vii) Single tee without door of 75x75x75 mm |
| 40 | viii) Single tee without door of110x110x110 mm |
| 41 | Providing and fixing soil, waste and vent pipes : |
| 42 | ii) 100mm dia Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989. |
| 43 | iii) 75mm dia Sand cast iron S&S pipe as per IS: 1729 |
| 44 | Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size) inside plastering 12mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement complete as per standard design : |
| 45 | i) Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : with Common burnt clay bricks of class designation 7.5 |
| 46 | PROVIDING INTERNAL WIRING |
| 47 | ii) Wiring for light point/fan point/exhaust fan point/call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FR PVC insulated copper conductor single core cable etc as required. |
| 48 | i) 6\\" dia light duty, make Khaitan or equivalent |
| 49 | Supply and Fixing of Discrete LED (Light Emitting Diode) Tube lights of 18 Watt, having IP65 protection class with Pressure Die Cast Aluminium housing & with Polycarbonate diffuser of approved make or equivalent as per direction of Engineer in charge. The LED shall be operating under voltage range of 140-270V with power factor more than 0.9. CCT(Correlated Colour temperature) shall be 5700 Kelvin (5665 K +/- 355 K), CRI (Colour rendering index) not less than 65. LED efficacy should be minimum 100 lumens/watt. The driver shall be of constant volt & constant current type with internal surge protection. Each lot of Fittings shall have serial numbers and accompany LM79 / IS 16106 test reports and reference/batch nos of LEDs and fittings for verification at site. The supply of LED lighting shall be covered by a warranty of at least 72 months from the date of supply of the lighting and the LED light fitting shall be complete in all respects including LED, LED Driver, Electronic circuitory, Luminarie etc. |
| 50 | Supply and fixing of following Electrical fittings /fixtures |
| 51 | ii) 5 Amp modular type switch |
| 52 | Providing and fixing 600x450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 53 | Providing and fixing toilet paper holder : |
| 54 | i) C.P. brass |
| 55 | Providing and fixing 600x120x5mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets & guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete. |
| 56 | Providing and fixing factory made door frame (single rebate) made out of single piece extruded solid PVC foam profile with homogeneous fine cellular structure having smooth outer integral skin having 62mm width and 32mm thickness, frame will be mitred & Jointed with self driven self tapping screws of size 38mm x 4mm & PVC solvent cement, including fixing the frame to wall with suitable dia and length anchor fastener as per manufacturer's specification and direction of Engineer-in-charge. |
| 57 | Providing and fixing factory made 30mm thick door shutter made of solid PVC foam profile. The styles & rails shall be of size 75mm x 30mm having wall thickness 5mm. The styles, top & bottom rails shall have one side wall thickness of 15mm integrally extruded on the hinge side of the profile for better screw holding power. The styles and rails shall be reinforced with MS tubes of size 33mm x 17mm x 1mm painted with primer, all four corners of reinforcement to be welded or sealed. Solid PVC extruded bidding (push fit type) will be set inside the styles and rails with a cavity to receive single piece extruded 5mm PVC sheet as panel. The styles and rails shall be mitred cut and joint with help of PVC solvent cement and self tapping screws. Single piece extruded solid PVC lock rail of size 100mm x 30mm with wall thickness 5mm & 15 mm integrally extruded in the middle of the lock rail & fixed with styles with the help of PVC solvent cement & self driven self tapping screws of size 100mm x 8mm complete as per manufacturer's specifications and direction of Engineer-in-charge |
| 58 | ii) Decorative finish (both side wood grained finish) |
| 59 | Providing & fixing IS:12817 marked stainless steel butt hinges (heavy weight) 100x60x2.50 mm with stainless steel screws etc. complete : |
| 60 | Providing & fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : |
| 61 | i) 200x10 mm |
| 62 | Providing & fixing chrome plated brass100mm mortise latch with one dead bolt with 6 levers & a pair of lever handles with necessary screws etc. complete (best make of approved quality). |
| 63 | PARTITIONS, DOORS, GLAZING, CEILING AND ALLIED WORKS For 2 Cabins other than LIC |
| 64 | Providing & fixing partition upto ceiling height consisting of G.I. frame & required board including providing & fixing of frame work made of special section power pressed/ roll form GI sheet with zinc coating 120gm/sqm(both side inclusive) consisting of floor and ceiling channel 50mm wide having equal flanges of 32mm & 0.50mm thick fixed to the floor & ceiling at the spacing of 610mm centre to centre with dash fastener of 12.5mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48mm wide having one flange of 34 mm and other flange 36mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610mm centre to centre by 6mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, Galvanised M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each with Zinc Coating of 120gm/sqm (both sides inclusive) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corner (25 mmx 25 mm x 0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture's specification and direction of engineer in charge all complete |
| 65 | i) 75 mm overall thickness partition with 12.5 mm thick double skin fire rated glass reinforced gypsum (GRG) plaster board conforming to IS: 2095: part 3:1996 (Board With BIS Certification Marks). |
| 66 | ii) 75mm overall thickness partition with 12.5 mm thick double skin tapered edged plain Gypsum plaster board conforming to IS:2095: part-I:2011 (Board With BIS Certification Marks). |
| 67 | Providing and fixing powder coated aluminium work (minimum thickness of powder coating 50 micron) consisting of tee/angle sections, of approved make conforming to IS : 733 in frames of false ceiling including aluminium angle cleats with necessary C.P. brass/ stainless steel sunk screws, aluminium perimeter angles fixed to wall with rawl plugs @ 450 mm centre to centre and fixing the frame work to G.I. level adjusting hangers 6 mm dia. with necessary cadmium plated machine screws all complete as per approved architectural drawings and direction of the Engineer-in-charge (level adjusting hangers, ceiling cleats and expansion hold fasteners to be paid for separately). |
| 68 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions,at top, bottom & sides with with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/panelling, C.P. brass/stainless steel screws including fixing all complete as per drawing & the directions of Engineer-in-charge. (Cost of glazing or panels to be paid for separately) |
| 69 | iii) For shutters of doors, windows & ventilators with Powder coated aluminium sections including providing fixing hinges/ pivots & making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) |
| 70 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item): |
| 71 | ii) With float glass panes of 5.0 mm thickness (weight not less than 12.5kg/sqm) |
| 72 | Extra for providing frosted glass panes 4 mm thick instead of ordinary float glass panes 4 mm thick in doors, windows and clerestory window shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured) |
| 73 | Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer with double speed adjustment with necessary accessories and screws etc. complete. |
| 74 | Providing & fixing chrome plated brass100mm mortise latch with one dead bolt with 6 levers & a pair of lever handles with necessary screws etc. complete (best make of approved quality). |
| 75 | Providing and fixing Brass 100mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete. |
| 76 | Providing & fixing IS:12817 marked stainless steel butt hinges (heavy weight) 100x60x2.50 mm with stainless steel screws etc. complete : |
| 77 | Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS:1868) transparent or dyed to required colour or shade with nuts & screws etc. complete: |
| 78 | i) 300x16 mm |
| 79 | Demolishing brick work manually/mechanical means including stacking of serviceable material & disposal of unserviceable material outside premises at an unobjectionable place as / direction of Engg-in-charge |
| 80 | For Conference Room |
| 81 | 100 kg, having proper glass to glass lock & 25 mm dia and 600 mm long SS matt finish handle selected by owner/Engineer in charge. Use of S.S. 304 Top/Bottom/Corner patch fittings to make & set partitions with fully glazed door. Pull Handle with Back to Back installation on Glass. Gaskets to prevent the contact between glass and metal. Outside Key operation with high security key and thumb turn from inside. Integral locking facility. Material:-Stainless Steel Grade 304. MAKES (HARDWARES) 1.,,OZONE OGL-PR-11-3 Mtrs SSS or approved equivalent make Fixed Glazing Profile basic rate per 3 mtr pcs 5862.00 Rs 2.,,KICH brand double cylinder 100 kg Floor Spring - FS112S (BASIC RATE 7347.00 RS EACH) OR Ozone FS-8400 or approved equivalent make standard Heavy Duty Double Cylinder Floor Spring O Door weight approx.100Kg. o Door width approx. 1000mm o Installation dimension: Length-306mm, Width-108mm, Height-40mm 3.,,Ozone OFS-ACC-GDP or approved equivalent make - Stainless Steel Pivot o Top pivot with 15mm diameter pin o Wear resistant SS 304 pivot pin o Finish SSS or KICH BRAND or approved equivalent make TOP PIVOT SET FOR GLASS DOOR PFP1S (BASIC RATE 320 RS EACH) 4.,,Ozone OPF-2 or approved equivalent make Top Patch o Variable pivot point of 55 or 65mm o With SS 304 cover o Finish: SSS or KICH BRAND or approved equivalent make TOP PATCH PF11S ((BASIC RATE 2100 RS EACH) 5. KICH BRAND or approved equivalent make BOTTOM PATCH PF12S ((BASIC RATE 1365 RS EACH. 6. KICH brand or approved equivalent make SS 316 grade Pull Handle set with lock of size 38mm *1125mm (c/c) * 1500mm (L) Include floor dust socket) (Satin finish) BASIC RATE 9870 RS EACH ) . GLASS: - Ashai, Saint Gobain or approved equivalent make, Hardware:- Ozone, KICH, Dorma, Geze or approved equivalent make All makes to be approved by Engineer in charge. Glass joints are with all necessary proper adhesive like clear silicon & finished by proper cleaning. Complete as per details given in approved drawing and as per instructions & approved by Engineer in charge. Contractor has to provide all necessary cut outs for Electrical works & no extra payment shall be made for it. Amount shall be paid only for the Partition between the False Ceiling & Flooring. Contractor have to use green certified product and submit certificate. |
| 82 | Providing frosted film of approved make i.e. 3M, Garware on 12 mm thick toughened glass doors / partition by mechanical/manual means and making approved design/pattern/logo all complete as per direction of engineer incharge. |
| 83 | Providing & fixing, in position concealed GI section for wall panelling with board of reqd. thickness fixed on the 'W' profile (0.55mm thick) having a knurled web of 51.55mm and two flanges of 26mm each with lips of 10.55 mm placed @ 610mm C/C in perimeter channel having one flange of 20mm and another flange of 30mm with thickness of 0.55mm & web of length 27mm. Perimeter channel is fixed on the floor and the ceiling with the nylon sleeves @ 610mm C/C with fully threaded self- tapping drive wall screws. Board is fixed to the W' profile with 25mm countersunk ribbed head screws @ 200mm C/C. all complete as per drawing & directions of engineer-in-charge. The joints of the boards finished with specially formulated jointing compound and 48mm wide jointing tape to provide seamless finish with; |
| 84 | ii) 12.5mm thick Gypsum plaster board conforming to IS:2095 (Part-1) :2011 (Board with BIS Certification Marks) |
| 85 | Providing and fixing 12mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminium doors, windows shutters and partition frames with C.P. brass/stainless steel screws etc. complete as per directions of Engineer in charge |
| 86 | ii) Pre-laminated particle board with decorative lamination on both sides |
| 87 | Providing and fixing cup board shutters 25mm thick, with Pre-laminated flat pressed 3 layer particle board or graded wood particle board IS: 12823 marked exterior grade (Grade l Type ll) having one side decorative lamination and other side balancing lamination including IInd class teak wood lipping of 25mm wide x12 mm thick with necessary screws & bright finished stainless steel piano hinges complete as per direction of the Engineer-in-Charge |
| 88 | Providing and fixing 12mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminium doors, windows shutters and partition frames with C.P. brass/stainless steel screws etc. complete as per directions of Engineer in charge |
| 89 | ii) Pre-laminated particle board with decorative lamination on both sides |
| 90 | False Ceiling Works |
| 91 | Providing and fixing 6 mm dia. G.I. level adjusting hangers (upto 1200mm length) fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40x3mm size 60mm long and stainless steel expandable dash fastener 12.5 mm dia. and 50mm long complete as per direction of Engineer-in-charge. |
| 92 | Providing & Fixing 15mm thick densified tegular edged eco friendly light weight calcium silicate false ceiling tiles of approved texture spintone/cosmos / Hexa or equivalent) of size 595 x 595 mm in true horizontal level suspended on inter locking metal grid of hot dipped galvanised steel sections (galvanising @ 120 grams per sqm including both side) consisting of main 'T' runner suitably spaced at joints to get required length and of size 24x38mm made from 0.33mm thick (minimum) sheet, spaced 1200mm centre to centre, and cross \\"T\\" of size 24x28mm made out of 0.33mm (Minimum) sheet, 1200mm long spaced between main'T' at 600mm centre to centre to form a grid of 1200x600mm and secondary cross 'T' of length 600mm and size 24 x28mm made of 0.33mm thick (Minimum) sheet to be inter locked at middle of the 1200x 600mm panel to from grid of size 600x600mm resting on periphery walls / partitions on Perimeter wall angle pre- coated steel of size(24x24X3000mm made of 0.40mm thick (minimum) sheet with the help of rawl plugs at 450mm centre to centre with 25mm long dry wall screws @ 230mm interval and laying 15mm thick densified edges calcium silicate ceiling tiles of approved texture (Spintone/Cosmos/hexa) in the grid including,cutting/ making opening for services like diffusers, grills,light fittings, fixtures, smoke detectors etc., wherever required, Main 'T' runners to be suspended from ceiling using G.I. slotted cleats of size 25x35x1.6mm ceiling with 12.5 mm dia and 50mm long dash fasteners, 4mm G.I. adjustable rods with galvanised steel level clips of size 85x30x0.8 mm spaced at 1200mm centre to centre along main'T', bottom exposed with 24mm of all T-sections shall be pre-painted with polyester baked paint for all heights,as per specifications,drawings & as directed by engineer-in- charge. Note :- Only calcium silicate false ceiling area will be measured from wall to wall. No deduction shall be made for exposed frames /opening (cut outs) having area less than 0.30 sqm.The calcium silicate tile shall have NRC value of 0.50(Minimum), light reflection > 85%, non - combustible as per B.S. 476 part IV, 100% humidity resistance & also having thermal conductivity<0.043 w/mK |
| 93 | Providing & fixing at all height FALSE CEILING including providing & fixing of frame work made of special sections power pressed from M.S. sheets and galvanised with zinc coating 120gsm/sqm as per IS : 277 and consisting of angle cleats of size 25mm wide x 1.6mm thick with flanges of 27mm and 37mm at 1200mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5mm dia x 50mm long with 6mm dia bolts ,other flange of cleat fixed to the angle hangers of 25x10x0.5mm of required length, and with nut and bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x 0.9mm running at the spacing of 1200mm centre to centre to which the ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26mm each having clips of 10.5mm at 450mm centre to centre shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64mm diax230mm long G.I. wire at every junction including fixing the perimeter channels 0.5mm thick 27mm high having flanges of 20mm & 30mm long, the perimeter of ceiling fixed to wall partition with the help of rawl plugs at 450mm centre to centre with 25 mm long drive-all screws @ 230mm interval including jointing & fixing of gypsum board of ceiling section & perimeter channel with the help of dry wall screws of size 3.5x25mm at 230mm centre to centre including jointing and finishing to a flush finish of tapered & square edges of the board with recommended jointing compoud. Jointing tapes, finishing with jointing compoud in 3 layers covering upto 150 mm on both sides of joint & 2 coats of primer suitable for board, all as per manufacturer specification and also including the cost of making openings for light fittings, grills, diffusers, cut outs made with frame of perimeter channels suitably fixed, complete as per drawing & specification and direction of the Engineer in Charge but excluding the cost of painting with: |
| 94 | i) 12.5mm thick tapered edge fire resistant GYPSUM BOARD conforming to IS:2095- PART-I:2011 (board with BIS Certification marks) |
| 95 | WALL FINISHING & PAINTING FOR EXISTING WALLS |
| 96 | Providing and applying plaster of Paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete |
| 97 | Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : |
| 98 | Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade with 2 or more coats |
| 99 | Providing and fixing of Wallpaper of app |
| 100 | PANTRY - CIVIL AND ALLIED WORKS |
| 101 | Providing & fixing partition upto ceiling height consisting of G.I. frame & required board including providing & fixing of frame work made of special section power pressed/ roll form GI sheet with zinc coating 120gm/sqm(both side inclusive) consisting of floor and ceiling channel 50mm wide having equal flanges of 32mm & 0.50mm thick fixed to the floor & ceiling at the spacing of 610mm centre to centre with dash fastener of 12.5mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48mm wide having one flange of 34 mm and other flange 36mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610mm centre to centre by 6mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, Galvanised M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each with Zinc Coating of 120gm/sqm (both sides inclusive) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corner (25 mmx 25 mm x 0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture's specification and direction of engineer in charge all complete |
| 102 | ii) 75mm overall thickness partition with 12.5 mm thick double skin tapered edged plain Gypsum plaster board conforming to IS:2095: part-I:2011 (Board With BIS Certification Marks). |
| 103 | Providing and fixing 12mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminium doors, windows shutters and partition frames with C.P. brass/stainless steel screws etc. complete as per directions of Engineer in charge |
| 104 | i) Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side |
| 105 | Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level |
| 106 | ii) RCC 1 Cement :1½ Coarse Sand: 3 Graded Stone Aggregate 20mm |
| 107 | Supply of Steel reinforcement for R.C.C. including straightening, cutting, bending, placing in position and binding all complete at all levels |
| 108 | ii) Thermo Mechanically Treated Bars of Fe- 500D grade or more, conforming to IS1786 |
| 109 | Providing and laying Brick work with common burnt clay F.P.S (non Modular) bricks of class designation 7.5 in foundation & plinth |
| 110 | Providing and laying cement plaster on surfaces with Coarse sand including curing etc. |
| 111 | i) 12mm Cement plaster of mix 1:4 (1 cement: 4 coarse sand) |
| 112 | Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10mm and down gauge) including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design in 75x75 mm deep chase |
| 113 | Providing and fixing 18mm thick gang saw cut mirror polished premoulded and prepolished, machine cut for kitchen platforms, vanity counters, sills, facias, Pump Island & similar locations of required size, approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding & polishing to edge to give high gloss finish etc. complete at all levels. |
| 114 | iv) Granite of any colour and shade having Area of slab over 0.50 sqm |
| 115 | iii) Granite of any colour and shade having Area of slab upto 0.50 sqm |
| 116 | Extra for providing edge moulding to 18mm Granite/ marble stone counters,Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in- Charge. |
| 117 | ii) Granite work |
| 118 | Extra for providing opening of required size & shape for wash basins/ kitchen sink in kitchen platform, vanity counters & similar location in marble/Granite/stone work including necessary holes for pillar taps etc.including rubbing and polishing of cut edges etc.complete |
| 119 | Providing & fixing ISI mark flush door shutters conforming to IS:2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains/cross bands & face veneers on both faces of shutters |
| 120 | i) 35mm thick including ISI marked Stainless Steel butt hinges with necessary screws. |
| 121 | Providing and fixing factory made door frame (single rebate) made out of single piece extruded solid PVC foam profile with homogeneous fine cellular structure having smooth outer integral skin having 62mm width and 32mm thickness, frame will be mitred & Jointed with self driven self tapping screws of size 38mm x 4mm & PVC solvent cement, including fixing the frame to wall with suitable dia and length anchor fastener as per manufacturer's specification and direction of Engineer-in-charge. |
| 122 | Providing & fixing IS:12817 marked stainless steel butt hinges (heavy weight) 100x60x2.50 mm with stainless steel screws etc. complete : |
| 123 | ii) With Semi rigid pipe of 40 mm dia |
| 124 | ii) PN - 16 Pipe, 20 mm OD (SDR-7.4) |
| 125 | i) PN - 16 Pipe, 16 mm OD (SDR-7.4) |
| 126 | PROVIDING INTERNAL WIRING |
| 127 | ii) Wiring for light point/fan point/exhaust fan point/call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FR PVC insulated copper conductor single core cable etc as required. |
| 128 | iii) Wiring for light/ power plug with 2X4 sq. mm FR PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit along with 1 No 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required. with modular switch, modular plate, suitable GI box |
| 129 | Supply and Fixing of Discrete LED (Light Emitting Diode) Tube lights of 18 Watt, having IP65 protection class with Pressure Die Cast Aluminium housing & with Polycarbonate diffuser of approved make or equivalent as per direction of Engineer in charge. The LED shall be operating under voltage range of 140-270V with power factor more than 0.9. CCT(Correlated Colour temperature) shall be 5700 Kelvin (5665 K +/- 355 K), CRI (Colour rendering index) not less than 65. LED efficacy should be minimum 100 lumens/watt. The driver shall be of constant volt & constant current type with internal surge protection. Each lot of Fittings shall have serial numbers and accompany LM79 / IS 16106 test reports and reference/batch nos of LEDs and fittings for verification at site. The supply of LED lighting shall be covered by a warranty of at least 72 months from the date of supply of the lighting and the LED light fitting shall be complete in all respects including LED, LED Driver, Electronic circuitory, Luminarie etc. |
| 130 | Supply and fixing of following Electrical fittings /fixtures |
| 131 | ii) 5 Amp modular type switch |
| 132 | iv) 15Amp modular type switch |
| 133 | v) 15Amp modular type 6 pin socket |
| 134 | Electrical Chimney |
| 135 | ELECTRICAL WORKS |
| 136 | PROVIDING INTERNAL WIRING |
| 137 | ii) Wiring for light point/fan point/exhaust fan point/call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FR PVC insulated copper conductor single core cable etc as required. |
| 138 | Supplying, drawing sub-main/power wiring with PVC insulated Copper 1100 V grade FRLS type through heavy duty rigid PVC conduit either on wall or in concealed. The job include terminations at both ends through proper jointing materials all complete for the following Make of Insulated wires shall be as per approved make |
| 139 | iii) 2 x 4 sq mm + 1 x 4 sq mm earth wire |
| 140 | SWITCHES, FUSES, MCBS, ELCBS ETC Supply and fixing of Modular switch frame with inner and outer face plates and accessories as per following details of approved including flush metal boxes/surface mounting boxes, plates, etc. all complete as per manufacturer's specification and direction of Engineer In-charge. |
| 141 | vii) 6A Modular Switch |
| 142 | viii) 15 A Modular switch |
| 143 | ix) 6A, 3 Pin Modular Socket |
| 144 | x) 15 A 6 Pin Modular socket |
| 145 | i) 1or 2 module frame |
| 146 | ii) 3 module frame |
| 147 | iv) 6 module frame |
| 148 | Supplying and fixing of following MCBs with necessery inter connections on existing DB, Panel board etc. |
| 149 | i) Upto 32A SP MCB |
| 150 | Supply and installation of MCB distribution board having Double door complete with tinned cu bus bar, neutral bus bar, earth bar, din bar, interconnection, earthing etc. without incoming isolator and MCBs |
| 151 | i) 2+4 way SPN |
| 152 | Supply and Fixing of Discrete LED (Light Emitting Diode) Tube lights of 18 Watt, having IP65 protection class with Pressure Die Cast Aluminium housing & with Polycarbonate diffuser of approved make or equivalent as per direction of Engineer in charge. The LED shall be operating under voltage range of 140-270V with power factor more than 0.9. CCT(Correlated Colour temperature) shall be 5700 Kelvin (5665 K +/- 355 K), CRI (Colour rendering index) not less than 65. LED efficacy should be minimum 100 lumens/watt. The driver shall be of constant volt & constant current type with internal surge protection. Each lot of Fittings shall have serial numbers and accompany LM79 / IS 16106 test reports and reference/batch nos of LEDs and fittings for verification at site. The supply of LED lighting shall be covered by a warranty of at least 72 months from the date of supply of the lighting and the LED light fitting shall be complete in all respects including LED, LED Driver, Electronic circuitory, Luminarie etc. |
| 153 | PROVISION OF EARTHING |
| 154 | ii) Providing earthing with 80 mm dia,3.0 M long GI (Heavy duty) perforated pipe as per IS:3043 (with latest ammendment) including providing suitable earth bus for interconnection, providing a mixture of salt & charcoal, making earth pit chamber with chequered plate cover as per standard Drwng. etc. all complete as per specification & direction of Engineer-In-charge |
| 155 | STORAGE UNIT |
| 156 | Providing and fixing Modular Laminated Free standing storage made in 19mm thk postformed laminated shutters with bull nose edge with all SS snap hinges, handles, locks etc as reqd. Shutter size varies between 375mm - 450mm width & height as per storage height. Depth of storage between 375mm-500mm as required (for files, folders coats etc) with select shelves duly adjustable as reqd on metal stud supports with sleeves set in at intervals of every 35mm, as per the following: structure of storage made in 19 mm thick commercial board board & finished in 1 mm thick laminate everywhere (outer side /innerside). Teak / maple edge margin to all edges, including laminated skirting in approved shade with all hardware, magnetic catchers, tower bolts, etc complete as per drawings. (Front area to be measured) Using Aluminium extruded Gchannel handle. |
| 157 | AV - CONFERENCE ROOM |
| 158 | 85\\" LED Display TV |
| 159 | Supply and installation of Conference Table in Conference Room of 15 seater of colour as per instructions of Engineer in-Charge |
| 160 | Transportation of valve/equipment weigh |
| 161 | Transportation ofv alve/equipment weight |
| 162 | CAR PARKING SHED |
| 163 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30 cm in depth, 1.5m in width as well as 10 sqm on plan) including taking out and disposal of excavated earth within or outside site to unobjectionable place and lift upto 1.5m, as directed by Engineer-in-charge. Disposed earth to be levelled and neatly dressed. Extra for levelling & neatly dressing of disposed soil completely to be paid separately as per item no. MPLCN00600 |
| 164 | i) All kinds of Soil |
| 165 | Supplying and filling in plinth with sand within specified grading zone of fine aggregates specified in table 3.1, clause 3.1.3 of attached specifications under floors, etc. in layers not exceeding 20cm in depth, each deposited layer to be compacted by ramming including watering, consolidating and dressing complete. |
| 166 | i) Local Fine Sand within grading zone IV |
| 167 | Supply and laying of water bound macadam of 100 mm consolidated thickness for subbase with 90 to 45 mm stone aggregate,11.2mm size screenings, chippings of stone and murrum spreading, watering and consolidating in camber with power roller complete as/specifications. |
| 168 | Supply and laying of water bound macadam in layers, each of 75 mm thick (consolidated) with 63 mm to 45 mm stone aggregate. Each layer shall be consolidated by power roller after watering, spreading chippings of stone and murrum complete as per specifications. Item includes supply of murrum 6 mm thick, watering and rolling with power roller complete with preparation of surface. Rate per Layer |
| 169 | Providing and laying Bitumen Penetration Macadam with hard stone aggregate of quality, size and grading as specified, with bitumen of suitable penetration grade including required key aggregate as specified spreading coarse aggregate with the help of self propelled/ tipper tail mounted aggregate spreader and applying bitumen by a pressure distributor and then spreading key aggregate with the help of aggregate spreader complete, including consolidation with road roller of minimum 8 to 10 tonne capacity to achieve specified values of compaction and surface accuracy : |
| 170 | i) For 50mm compacted thickness using coarse aggregate of size 50-20 mm graded @ 0.60 cum per 10 sqm key aggregate of size 12.5 mm graded @ 0.15 cum per 10 sqm. With paving asphalt grade VG-10 @ 50 kg/10 sqm. |
| 171 | Providing & laying Bituminous concrete using crushed stone aggregates of specified grading,premixed with bituminous binder and filler, transporting the hot mix to work site by tippers, laying with paver finisher equipped with electronic sensor to the required grade, level & alignment & rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction & density as/specification complete and as per directions of Engineer-in-Charge |
| 172 | i) 40/50 mm compacted thickness with bitumen of grade VG-30 @5.5% (percentage by weight of total mix) and lime filler @ 3% (percentage by weight of Aggregate) prepared in Batch or Drum Type Hot Mix Plant of 100-120/60-90 TPH capacity. |
| 173 | Providing and laying in position cement concrete of specified grade excluding cost of centering & shuttering. All work up to plinth level: |
| 174 | v) 1:3:6(1 Cement : 3 Coarse Sand : 6 Graded stone aggregate of 20mm) |
| 175 | iii) 1:2:4(1 Cement : 2 Coarse Sand :4 Graded stone aggregate of 20mm) |
| 176 | Centering and shuttering including strutting, propping etc. and removal of form work for: |
| 177 | Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level |
| 178 | ii) RCC 1 Cement :1½ Coarse Sand: 3 Graded Stone Aggregate 20mm |
| 179 | Providing & Laying Reinforced cement concrete work in walls (Any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level UP TO FLOOR V LEVEL excluding cost of centering, shuttering, finishing and reinforcement : |
| 180 | ii) RCC 1 Cement :1½ Coarse Sand: 3 Graded Stone Aggregate 20mm |
| 181 | Supply of Steel reinforcement for R.C.C. including straightening, cutting, bending, placing in position and binding all complete at all levels |
| 182 | ii) Thermo Mechanically Treated Bars of Fe- 500D grade or more, conforming to IS1786 |
| 183 | Centering and shuttering including strutting, propping etc. and removal of form for : |
| 184 | iii) Suspended floors,roofs,landings,balconies, access platform and Shelves (Cast in situ) |
| 185 | Carriage charge for disposal of earth by mechanical means, including loading, transporting, stacking, unloading to approved municipal dumping ground / unobjectionable place as per direction of Engineer- in-Charge beyond IOCL Premises for all leads and including all lifts. |
| 186 | ii) Distance > 1 km< 3 km |
| 187 | Structural steel work riveted,bolted or welded in built up sections, trusses & framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete: |
| 188 | Steel work in built up tubular (round,square or rectangular hollow tubes etc) trusses etc. including cutting,hoisting fixing in position and applying a priming coat of approved steel primer, including welded and bolted with special shaped washers etc. complete. |
| 189 | i) Hot finished welded type tubes |
| 190 | Providing and fixing Klippon Galvalume steel profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) of Cold rolled steel confirming to IS:513-2008 of base metal thickness 0.50 mm, having Yield Stress of Min. 275 MPa. Steel surface shall have hot dip metallic coating of Al-Zinc alloy comprising 55% Alluminium, 43.5% Zinc and 1.5% Silicon as per the ASTM-A792M, with total mass of coating on both sides shall be 150 gms/sqm. The steel shall have organic coating with Silicon Modified Polyester (SMP) /Super Durable Polyester (SDP) paint on continuous coil coating line. The thickness of coating on top side shall be 20-25 Microns (i.e. 15-18 microns SMP /SDP paint over 5-7 microns epoxy primer) and back side 8-10 Microns SMP/SDP paint over epoxy primer. Total Coated Thickness (TCT) shall be 0.58 MM. Sheet shall have protective guard film of thickness of 25 microns minimum to avoid scratches while transportation and should be supplied in single length up to 6m or as desired by Engineer-in-charge. |
| 191 | i) Profile Sheet for roofing |
| 192 | Supplying and fixing MS foundation bolts with necessary GI nuts and washers of specified sizes,all conforming to relevant Indian Standards and as approved by Engineer-in-charge : |
| 193 | ii) 16mm dia x 400mm long with 75 mm dia x 5 mm thick plate |
| 194 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade with two or more coats over an under coat of suitable shade with ordinary paint of approved brand and manufacture. |
| 195 | Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars & disposal of unserviceable material outside site to an unobjectionable place as/ direction of Engineer-in-charge |
| 196 | Extra for cutting reinforcement bars manually/ by mechanical means in R.C.C. or R.B. work (Payment shall be made on the cross sectional area of R.C.C. or R.B. work) as per direction of Engineer-in-charge. |
| 197 | Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars & disposal of unserviceable material outside site to an unobjectionable place as/ direction of Engineer-in-charge |
| 198 | Centering and shuttering including strutting, propping etc. and removal of form for : |
| 199 | v) Columns, Pillars, Piers, Abutments, Posts and Struts. |
| 200 | TELEPHONE SYSTEM |
| 201 | Supply, installation, testing and commissioning of Indoor TelephoneDistribution J.B. made out of 2.03 mm (14 gauge) sheet steel, with oneanti-rust coat of primer, with two finished coats of approved epoxypaint, with Krone type terminals with hinged lockable door, detachablegland plate at the bottom/top complete with termination and connectionsof incoming/outgoing cables, including all labour and materials, as perspecifications of this tender and directions of Engineer-in-Charge,,,,,, |
| 202 | TDJB Flush mounting type with an additional cable pull box at bottom foreasy termination of cable suitable for 1 nos 20 Pair incomingcable(s) and 20 nos 1 Pair outgoing cable(s) |
| 203 | Supply, installation, connection, testing and commissioning of followingplug - in type sockets for Telephones extensions including supply of sheet boxes with covers connection of socket and plug, including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge. - Flush Mounting Type. |
| 204 | Wiring with (No. of wires given below) 660 V grade, 0.63 mm dia.annealed tinned copper conductor, PVC insulated twin flat wire as perrelevant IS in already laid surface/concealed conduit from TDJB onwardsto telephone sockets including supply of Wires, termination andconnection, including all labour and materials, as per approveddrawings, specifications of this tender and directions ofEngineer-in-Charge. |
| 205 | 1 No. twin flat wire. |
| 206 | Supply of Standard Table Top Model - Analog Phones with Digital Display |
| 207 | Supply of IP based Desktop phone Min 3\\" monochrome display, sensitive soft keys with LED, 3 audio keys (Mute/Speaker/Headset) with LED, 16 free programmable feature keys with LED, IEEE 802.3af PoE, Class 2, 10/100/1000 Base T. |
| 208 | MISCLANNEOUS WORKS |
| 209 | Providing and fixing Wooden panelling for wall & columns as per drawings, design & specifications. The frame work shall be made of pine wood of size 50x25 thick in both horizontal and vertical direction at 600 mm c/c spacing. All framework to be painted with fire-resistant & anti termite paint. The framework shall be covered with single layer 12mm thick BWR plywood (FSC certified) on one side 3 mm thick laminate of approved make , shade & pattern shall be fixed over the ply with necessary adhesive .Actual seen surface area. From FFL to maximum height will be measured and paid. Rate shall be inclusive of all associated hardware ,cut-outs for lights/switches,adhisives etc. All complete (As per drawings, and as directed by Engineer-In-Charge at site) |
| 210 | Providing & Fixing of \\"Rechargeable Exit Signage\\" with inbuilt Ni-Cd rechargeable battery 16 to 24Hrs recharging period & back-up facility. |
| 211 | Supply and fitting of notice board with glass door - 900mm X 600mm |
| 212 | Indian Oil Logo, Assam Oil Division Logo and Role of Honor Plaque |
| 213 | Supply, Fabrication, Packaging , Transportation, Erection, Installation and commissioning of lettering of 8 mm thick opal white acrylic letter UV2 protected as per design including the structural required for fixing of the letters. |
| 214 | iii) Brick work in Cement mortar 1:4 (1 cement: 4 coarse sand) in superstructure in all shapes & sizes in superstructure ABOVE PLINTH & UP TO FLOOR V LEVEL |
| 215 | TRANSPORTATION OF EXISTING OFFICE FURNTIURE AND RECORDS |
| 216 | x) Half brick masonry with common burnt clay F.P.S.(non modular) brick of class designation 7.5 in Cement mortar 1:4 (1 cement:4 coarse sand in superstructure ABOVE PLINTH level & UP TO FLOOR V LEVEL |
| 217 | Providing & fixing chrome plated brass100mm mortise latch with one dead bolt with 6 levers & a pair of lever handles with necessary screws etc. complete (best make of approved quality). |
| 218 | ii) Sink with drain board 510x1040 mm bowl depth 225mm |
| 219 | i) Foundations,footings,bases of column |
| 220 | Finishing with Epoxy paint, 2 or more coats at all locations on steel work prepared & applied as per manufacturer's specifications including appropriate priming coat,preparation of surface, etc. |
| 221 | Providing and applying plaster of Paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 22, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 29, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 6 daysJul 30, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 7 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender