Tender For Improvement Of Lift Irrigation Scheme Lower Kothipura In Tehsil Sadar District Bilaspur (Sh: Laying Jointing And Testing Of Hdpe Pipe And Construction of Reinforced Cement Concrete Outlets).Estimated Amount- 402730/- Emd- 8055/- Time- Two
Tender Value
4.02 Lakhs
Estimated cost
Bid Submission
31 Jul 2026
4 days left
EMD
8055
Bank guarantee accepted
Document Fee
350
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Bilaspur → Himachal Pradesh
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Improvement Of Lift Irrigation Scheme Lower Kothipura In Tehsil Sadar District Bilaspur (Sh: Laying Jointing And Testing Of Hdpe Pipe And Construction of Reinforced Cement Concrete Outlets).Estimated Amount- 402730/- Emd- 8055/- Time- Two Months
BOQ
| Sl. No. | Item Description |
| 1 | Excavation in foundation trenches etc. in earth work in all kinds of soil such as pick work, jumper work, blasting work in soft/hard rock, chiseling wedging out of rock where blasting is prohibited saturated soil including bailing/pumping out of water, stacking the excavated soil in all leads and lifts clear from the edge of excavation and then returning the stacked soil in 15cm layers, when required into sides of foundation etc, consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth as directed within all leads and lifts |
| 2 | Laying jointing and testing in trenches HDPE pipe of following diameter and classes as per IS: 4984-1995 grade PE-80 class PN-4.00 and jointing the pipes through push type compression joints by hydraulically operated machine complete with butt (heat) fusion welded joints with necessary fittings such as bends, tees, reducers etc, fabricated in accordance with IS: 8360 and IS: 8008 with latest amendements and shall be provided as per site conditions. The flanging of the pipes shall be made as and where required conforming to IS: code 8008 and 7634, stud ends shall be fussion welded on pipes & flanges shall be provided with slip on covered by epoxy coating/plastic powder. The flanges should be conform to ANSI B 16.5 with necessary nuts and bolts (Earth work in trenches to be measured and paid for separately) in all leads and lifts and to the entire satisfaction of the Engineer-in-charge. |
| 3 | 110mm dia HDPE pipe PE-80 PN-4.00 |
| 4 | 125mm dia HDPE pipe PE-80 PN-4.00 |
| 5 | 140mm dia HDPE pipe PE-80 PN-4,00 |
| 6 | Providing and laying cement concrete 1:3.6 (1cement: 3sand: 6 graded stone agg. 40mm nominal size) and curing complete excluding the cost of form work in foundation and plinth in all leads and lifts and to the enitre satisfaction of the Engineer-in-charge |
| 7 | Providing and laying cement concrete 1:1.5:3 (1cement: 1.5 sand:3 graded stone aggregate 20mm nominal size) and curing complete excluding the cost of form work and reinforcement for reinforced concrete work in:- |
| 8 | Foundation footings base of columns and the like and mass concrete and to the entire satisfaction of the Engineer-in-charge. |
| 9 | Wall any thickness but not less than 0.1mtr thickness attached pilasters, buttresses, plinth and string courses etc. from top of foundation level up to floor two level and to the entire satisfaction of the Engineer-in-charge |
| 10 | Providing laying of tor steel reinforcement for RCC work including bending binding cutting and placing in position complete in all depths and heights and to the entire satisfaction of the Engineer-in-charge. |
| 11 | Providing form work with steel plates 3.15mm thick welded with angle iron in frame 30x30x5mm so as to give a fair finish including centering shuttering, strutting and propping etc. with wooden battens and ballies, height of propping and centering below supporting floor two ceiling not exceeding 4 mtr and removal of the same for in-situ reinforcedconcrete and plain concrete working:- |
| 12 | Vertical surfaces such as walls (any thickness) partitions and the like including attached pilasters buttresses, plinth and string courses and the like and to the entire satisfaction of the Engineer-in-charge. |
| 13 | Providing and fixing cast iron Alfa valve of superior quality \\"VV make in all leads and lifts and to the enitre satisfaction of the Engineer-in-charge |
| 14 | 100 mm dia |
| 15 | 150 mm dia Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 22, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 31, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 4 daysJul 31, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 4 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender