Tender For Providing Upvc Partition And Instrument Wash Scrub Sink Arrangements In Second Floor Dialysis Ward In Critical Care Block Building In Tirunelveli Medical College Hospital At Tirunelveli District
Tender Value
5.95 Lakhs
Estimated cost
Bid Submission
05 Aug 2026
13 days left
EMD
5950
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Tirunelveli → Tamil Nadu
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Providing Upvc Partition And Instrument Wash Scrub Sink Arrangements In Second Floor Dialysis Ward In Critical Care Block Building In Tirunelveli Medical College Hospital At Tirunelveli District
BOQ
| Sl. No. | Item Description |
| 1 | The supply and installation of uPVC partitions with doors shall utilize uPVC profile sections with an outer wall thickness of 2.30mm (±0.2mm), featuring an outer frame of 74mm x 60mm x 56mm, a shutter of 104mm x 60mm x 66mm, a mullion of 72mm x 60mm x 36mm, a glazing bead of 35mm x 18mm, a 20mm multi-chambered hollow uPVC panel section of 150mm x 20mm, and a uPVC panel bead of 19mm x 16mm. All profiles of frames, sash, and mullion shall be reinforced, where required, with 1mm thick GI steel sections. The door will be equipped with 3D hinges for enhanced weight holding capacity, and security devices such as multipoint lock systems with a cylinder lock facilitated handle, all compliant with relevant specifications and departmental directives. Glazing or uPVC panels shall be 5mm thick Plain Toughened or uPVC panel grip, held by TPE (Grey) weather-sealed gaskets. All corners and mullion joints of the frame and sash shall be mitred cut and fusion welded without mechanical joints, with all welded joints neatly trimmed to a grooved nib finish, ensuring the finished products are free from sharp edges. The complete units shall be fixed into pre-finished openings by drilling and fastening through the outer frame using high-quality fasteners, and silicon sealant shall be applied to fill the gap between the wall and the frame for a leak- proof installation and completion etc., Complete and as directed by the department officers. |
| 2 | Providing UPVC (Un-Plasticized Polyvinyl Chloride) Door: Providing and fixing casement doors fabricated from un- plasticized polyvinyl chloride (uPVC) sections.Profiles: The profiles should be three chamber system which provides high insulation properties with outer frame 60mm x 55mm with an outer wall thickness of 2.4mm. The window unit should be designed with all corner joints mitred and fusion welded. Windows should be steel reinforced with 25 x 24 x 25mm steel reinforcement with a thickness of 1mm to have dimensional stability. The sash should be of 60 x 102mm. The mullion should be of 60 x 74mm. The profiles should have co-extruded seals.Hardware: All the hardware like friction stays, handles should be screwed with self tapping screws. The handles, locks should be designed so that they cannot be released from outside.Glazing: The window system should be glazed with 5mm plain float glass / 6mm bison lamInstallation: The profiles should be cut to length and welded 45 degrees. The window should be designed such that the water drainage does not pass through the reinforcement chamber. The window system should be fixed directly to the plastered brick wall using self expanding nylon plug and driving ms electroplated screws into plug. |
| 3 | Supplying and fixing of stainless steel SS 304 grade wash tub of overall size of 1.35 x 0.65 x 1.20m. The wash tub will be of depth 0.65m. The top width of the wash tub is 0.60m and bottom width of wash tub is 0.30m. The balanced bottom portion is covered by SS 304 grade stainless steel plate with SS screws. The tub fixed into the wall by using stainless steel angles of size 25 x25mm x 1.6mm. The rate including 2Nos of Stainless Steel Elbow action tap 15mm tap, 1 No of 40mm stainless steel waste cup, Dismantling the masonry (or) concrete wall and redoing the same to its original condition folding charges, transporting, Installation charges etc complete. |
| 4 | Supplying and fixing of stainless steel SS 304 grade wash tub of overall size of 0.75 x 0.65 x 1.20m. The wash tub will be of depth 0.65m. The top width of the wash tub is 0.60m and bottom width of wash tub is 0.30m. The balanced bottom portion is covered by SS 304 grade stainless steel plate with SS screws. The tub fixed into the wall by using stainless steel angles of size 25 x25mm x 1.6mm. The rate including 1No of Stainless Steel Elbow action tap 15mm tap, 1 No of 40mm stainless steel waste cup, Dismantling the masonry (or) concrete wall and redoing the same to its original condition folding charges, transporting, Installation charges etc complete. |
| 5 | Supplying, laying and jointing CPVC pipes of Standard Dimension Ratio-11 (Pressure class 1) conforming to IS:15778 - 2007 of approved quality and best variety of the following dia including cutting and fixing CPVC specials using CPVC adhesives (Solvent Cement) (but excluding cost of such specials) and fixing into wall with teak wood plugs, CPVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications and as directed by the departmental officers. (The CPVC pipes shall be got approved by Executive Engineer before use on works). |
| 6 | External water supply above ground level - 25mm dia CPVC pipe |
| 7 | External water supply below ground level - 32mm dia CPVC pipe |
| 8 | Supplying and fixing in position first quality and approved variety of Gun metal Gate Valve / Wheel Valve with BIS make of the following dia including cost of shellac, thread balls, etc., complete complying with standard specifications (for both internal and external water supply arrangements). The valves to be used on work shall be got approved by the Executive Engineer before use on work. |
| 9 | 25mm dia Gate valve |
| 10 | 32mm dia Gate valve |
| 11 | GST Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 21, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 05, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 13 daysAug 06, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 14 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender