Tender for Tender for Construction Of An Indoor Stadium On The Land Situated Behind The Sports Ground Of Government School, Behror As Per Nit
Tender Value
3.64 Crore
Estimated cost
Bid Submission
10 Aug 2026
18 days left
EMD
7.28 Lakhs
Bank guarantee accepted
Document Fee
2360
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Alwar → Rajasthan
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Construction Of An Indoor Stadium On The Land Situated Behind The Sports Ground Of Government School, Behror As Per Nit
BOQ
| Sl. No. | Item Description |
| 1 | Excavating trenches of required width for pipe cables, etc. including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 Mtr. including taking out the excavated soil, and then returning the soil as required in layers not exceeding 20cm in depth including consolidating each deposited layer by ramming, watering etc. and disposal of surplus excavated soil as directed within a lead of 50 Mtr.: All kinds of soil Pipes cables, etc. exceeding 80mm dia but not exceeding 300mm dia. |
| 2 | Earth work in excavation by mechanical means (Hydraulic Excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter. All kinds of soils |
| 3 | Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level. M10 grade Nominal Mix 1: 3: 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) |
| 4 | Random Rubble stone masonry for with hard stone in foundation and plinth in Cement Sand mortar above 30 CM thick wall in: Cement Mortar 1:6 ( 1-Cement : 6-Sand). |
| 5 | Random rubble dry stone Kharanja under floor. |
| 6 | Providing and laying in position Ready mix concrete manufactured in fully automatic Batching Plant and transported to site in transit mixer for having continous agitated mixer, manufactured as per approved mix design of specified grade of RCC work including pumping of R.M.C. from transit mixer to site of laying , exculding the cost of centering, shuttering and reinforcement with all lead and lift including cost of admixtures in recommended portion as per IS 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer in charge. All works upto floor V floor M20 grade Design Mix by using cement as per codal provision. |
| 7 | Centering and Shuttering with plywood or steel sheets including strutting, propping bracing both ways and removal of formwork for foundation , footings, strap beam, raft , bases of columns etc. |
| 8 | Centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel props and removal of formwork for upto floor five level for : Walls (any thickness) including attached pilasters, buttresses plinth and string course. |
| 9 | Centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel props and removal of formwork for upto floor five level for : Columns, pillars, posts and struts etc. |
| 10 | Providing and fabricating reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor five level. ('Original producers' who manufacture billet directly from iron ores and roll the bilets to produce steel conforming to IS:1786) Thermo-mechanically Treated bars (Conforming of relevent IS code) |
| 11 | Brick work with F.P.S. bricks of class designation 75 in superstructure above plinth level upto floor V level in all shapes and sizes in : Cement mortar 1 : 4 (1 cement : 4 coarse sand) |
| 12 | Half brick masonry in Superstructure , above plinth level upto floor V level using bricks of designation 75 Cement mortar 1 : 4 (1 cement : 4 coarse sand) |
| 13 | Carriage of Earth sand, line, morrum etc. including loading, unloading complete with all lead. |
| 14 | Filling available excavated earth (excluding rock) in trenches, plinth side of foundation etc. in layers not exceeding 20 cm. in depth, consolidating each deposited layer by ramming and watering including lead up to 50 meter and with all lift. |
| 15 | Plaster on new Surface on wall in cement sand mortar 1 : 3 including racing of joints etc. complete fine finish : 20 mm thick |
| 16 | Providing and fixing steel gate, grating , and grills made of angles, tees, square bars, flats,or black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide |
| 17 | Providing and fixing aluminum work for doors ,windows, ventilators and partition with extruded built up standard tubular / appropriate Z sections and other sections of approved make conforming to IS :733 and IS :1285, fixed with rawl plugs and screws or with fixing clips ,or with expansion hold fasteners including necessary filling up of gap. at junctions , at top ,bottom and sides with required PVC/neoprene felt etc. Aluminium section shall be smooth ,rust free, straight ,mitered and jointed mechanically wherever required including cleat angle Aluminium snap beading for glazing /paneling , C.P. brass/ stainless steel screws Al. Tower bolt & Al. handle & Al. Aldrop etc.,all complete as per architectural drawings and the directions of Engineer- in – charge .(Glazing and paneling to be paid for separately). For fixed portion Powder coating aluminum ( minimum thickness of powder coating 50 micron) |
| 18 | Providing and fixing aluminum work for doors ,windows, ventilators and partition with extruded built up standard tubular / appropriate Z sections and other sections of approved make conforming to IS :733 and IS :1285, fixed with rawl plugs and screws or with fixing clips ,or with expansion hold fasteners including necessary filling up of gap. at junctions , at top ,bottom and sides with required PVC/neoprene felt etc. Aluminium section shall be smooth ,rust free, straight ,mitered and jointed mechanically wherever required including cleat angle Aluminium snap beading for glazing /paneling , C.P. brass/ stainless steel screws Al. Tower bolt & Al. handle & Al. Aldrop etc.,all complete as per architectural drawings and the directions of Engineer- in – charge .(Glazing and paneling to be paid for separately). For shutters builtup standard tubular sections of openable doors ,windows & ventilators including providing & fixing hinges / rollers etc. and making provision for fixing of fittings wherever required (lockes shall be paid for separately). Powder coating aluminum ( minimum thickness of powder coating 50 micron) |
| 19 | Providing and fixing double action hydraulic floor spring of approved brand and manufacture IS : 6315 marked, for doors including cost of cutting floors as required, embedding in floors and cover plates with brass pivot and single piece M.S. With stainless steel cover plate |
| 20 | Providing and fixing 100mm brass locks (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete. |
| 21 | Filling the gap upto 5 mm depth and 5 mm width in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete. |
| 22 | Providing and fixing aluminium U shape handle of size 100mm with SS screws etc. Complete as per direction of Engineer-in-charge Powder coated minimum thickness 50 micron aluminium |
| 23 | Providing and fixing expanded grill made of aluminum as per design and drawing having members section of size 7.5mm x 6.0mm and opening of size 102mm x 99mm to aluminum window/vent with required screws, Y and H aluminium section (as per drawing) at the ends and middle joints respectively complete in all respect as per direction of engineer in charge. Powder coating aluminum ( minimum thickness of powder coating 50 micron) |
| 24 | Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade including all scaffolding: Two or more coats on new work including prepartion of base with primer, putty, lippy etc complete in all respect. |
| 25 | Painting exterior surface of Wall with 100% acrylic exterior paint of approved brand and manufacture to give an even shade with two or more coats including prepartion of base with sand papering, primer, putty, etc complete in all respect including scaffolding and safety provision New Work |
| 26 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work |
| 27 | Add extra for providing richer mixes respectively at all floor levels Providing M-30 grade concrete by using cement as per codal provision instead of M-20 grade design mix. |
| 28 | Interlocking Concrete Block Pavement with M-30 Grade 0.30 Mtr x 0.30Mtr x 0.15 Mtr Edge Blocks (measurements shall be made inner toinner side of edge blocks) Providing and Laying of Interlocking M-30 grade Concrete Block Pavements having thickness 60 mm as per drawings and as per IS 15658:2006.and materials conforming to MoRTH Specification Clause 602 with M-30 Grade 0.30 Mtr x 0.30 Mtr x 0.15 Mtr Edge Blocks. Category 'B' : Dentated only two side like I,Z,T shape as per IRC:SP:63-2004 |
| 29 | Supply of stacking of good earth at site complete including loading unloading & transporation etc |
| 30 | Providing and applying white cement based putty over plastered surface to prepare the surface even and smooth complete New Plastered Surface (three or more coats) |
| 31 | Extra for providing toughened glass panes instead of ordinaryfloat glass panes in doors, windows and clerestory windowshutters. (Area of opening for glass panes excluding portioninside rebate shall be measured). |
| 32 | Providing and injection Chloropyrifos Emulsifiable concentrate 20% with 1% concentration for PRECONSTRUCTIONAL Anti termite treatment as per IS 6313 part III as amended from time to time and creating a continuous chemical barrier under and around the column pits, wall trenches, basement excavation, top surface of plinth filling, junction of wall and floor along the external perimeter of building expansion joints, over the top surface of consolidated earth of which aproch is to be laid surrounding of pipes and conduits etc. complete as per specification (Plinth floor area only shall be measured for payment). |
| 33 | Supplying chemical emulsion in sealed containers including delivery as specified. Chlorpyriphos/Lindane emulsifiable concentrate of 20% |
| 34 | Earth work in surface excavation not exceeding 30cm. in depth but exceeding 1.5 meter in width as well as10 Sqm on plan including disposal of excavated earth up to 50 Mtr. and lift up to 1.5 Mtr. disposed soil to be levelled and neatly dressed:All kinds of soil |
| 35 | Providing and fixing sun control film, thickness of film 1 Mil Visible Light Transmittance 4-24% & Solar Energy Transmittance 42-51% & Total solar Energy rejection 37-43%of approved colour and shade , complete in all respect , at all level , as directed by engineer- in -charge. |
| 36 | P&F rigid PVC Pipe (IS:4985 mark) class II/ (4 Kg. /Cm2.) approved quality /make including joining the pipe with solvent cement rubber ring and lubricant. 110 mm dia |
| 37 | P&F rigid PVC Pipe (IS:4985 mark) class II/ (4 Kg. /Cm2.) approved quality /make including joining the pipe with solvent cement rubber ring and lubricant. 160 mm dia |
| 38 | P & F European type white glazed vitreous china 1st quality W.C pan (IS : 2556 Mark) with P or S trap including cutting and making good the wall and floor |
| 39 | P & F water closet Seat Covers with brass hinges complete : Solid PVC (IS 2548 marked) grade-I Black for EWC. |
| 40 | P & F C.P. lugs for toilet seat cover. |
| 41 | P & F Low level Flushing Cistern of 10 litres capacity (IS : 2556 mark) of approved make with complete fittings C.I. brackets duly painted, brass ball cock with ball (IS: 1703 mark) complete including cutting and making good the wall: PVC with PVC bend and superior internal fittings as per IS : 7231 . |
| 42 | P & F WVC Wash basin (Ist quality IS:2556 Mark) of approved make with C.I. brackets duly painted 1 No. 15 mm C.P. Pillar cock (IS:8934 Mark) & 32 mm C.P. brass waste coupling of approved make, P.V.C Waste pipe with PVC nut 32 mm complete including cutting & making good the wall : Size 510 mm x 400 mm |
| 43 | P & F Grating of approved quality/make: Synthetic Material(PTMT) of approved quality/make size 150mm dia. |
| 44 | P & F Extension Pipe for bib cocks of approved quality/make. C.P. brass of Heavy & Superior quality 150 X 15mm. |
| 45 | P & F Jet spray for water closet with C.P. Copper Tube flange of approved make. |
| 46 | Providing & fixing C.P.flange for 15mm dia taps. |
| 47 | P & F G.I. pipes (Internal Work) with G.I. Fittings excluding union (IS:1239 Mark) & MS clamps including cutting and making good the walls and floors: Exposed on wall 'B' Class |
| 48 | 15 mm dia nominal bore. |
| 49 | 20 mm dia nominal bore. |
| 50 | Concealed pipe in wall including painting with anticorrosive bitumen paint 'B' Class |
| 51 | 15 mm dia nominal bore. |
| 52 | 20 mm dia nominal bore. |
| 53 | P & F Pilllar Cocks (IS :8931 : 1993 Mark) of superior quality and approved make: C.P. Pillar cock, Swan-neck with casted spout, 15mm nominal bore. |
| 54 | P & F Bib Cock (IS : 8931 Mark), Superior quality of approved make: Long nose, 15mm nominal bore weight not less than 810 gm |
| 55 | P & F Stop Cock (IS :8931 Mark), superior quality & of approved make: (-do-) Concealed Stop Cock 15mm. |
| 56 | P & F Inlet Connection (Angle Valves) Superior quality, of approved make, for Wash basin, Gyser etc. C.P. Inlet connection 15mm.Brass (IS : 8931 marked) |
| 57 | P & F PVC Storage Tank ISI Marked (IS : 12701) indicating the BIS license No), of approved make with cover, 25mm dia 1M long G.I. over-flow pipe & 25 Cm. long wash out pipe with plug & socket, including making connection etc., complete of approved design: 1000 litres capacity. |
| 58 | P & F Ist quality WVC Urinal (IS:2556 mark) with 25 mm dia G.I. waste pipe, dome couplings, concealed iron brackets or screws etc. complete. Flat Back (large) or half stall size 590x375x390 mm. |
| 59 | P & F C.P. brass Urinal Flush pipe set complete with flanged brackets of approved make. For 2 unirals |
| 60 | P & F Marble Urinal Partition slab both sides polished of approved design cut from marble size 900x600mm. Makrana II quality marble having light spots. |
| 61 | P & F Square-mouth gully trap `A` grade (IS :marked) of approved make complete with C.I. grating, frame & Cover masonary chamber in C.M. 1:6, 100mm thick C.C. 1:5:10 base concrete, 40mm thick C.C.M-15 grade coping, 12mm thick cement plaster in CM 1:3 complete as per approved design & type.Trap size 225 X 150 mm, 15 Kg. C.I. cover with frame Internal Chamber size 450 X 450mm. |
| 62 | Construction of manhole in all type of soil inner size 90 X 60 Cm. 300 mm thick masonry in CM 1:6, 10 Cm. thick cement concrete 1:5:10 in foundation, 20 mm thick inside plaster in CM 1:6, finished with floating neat cement, 50mm thick M-15 grade C.C. flooring, making channels, 80mm thick stone slab covering with 40mm thick M-15 grade C.C. flooring, Cement cover with frame of 450mm dia, earthwork etc. complete as per design including disposal of surplus earth within 50 mtr. lead. Depth up to 0.5 M |
| 63 | Construction of septic Tank in all types of soil with 40 Cm .thick masonry in CM 1:6, 15 Cm thick C.C bed of 1:5:10, M-15 grade C.C floor & RCC slab covering with M15 grade c.c. floor, 50 mm thick stone slab partition walls, 20 mm thick plaster in CM 1:6 finished with neat floating cement, 4 Nos stone foot rests of approved design ,two No. 450 mm dia each Ferro cement cover with frame, earth work etc. complete as per approved drawing including disposal of surplus earth within a lead of 50 mtr:- Size 400 x140x150 cm.(for 50 users) with 115 mm thick RCC (M-20) slab with Tor steel reinforcement 10mm ϕ @15 cm c/c bothways including shuttering complete in all respect. |
| 64 | Add extra if RCC slab of designed thickness & reinforcement is proivded on manhole in place of stone slab ( actual area of RCC slab to be measured). |
| 65 | Providing and fixing unplasticized Poly Vinyl Chloride (UPVC) SWR pipes type `B' for sciland waste dischareg system (IS : 13592: 1992 marked) of approved quality/ make. 100 mm Dia |
| 66 | Coupler |
| 67 | Bend 87.5 Dg. |
| 68 | Bend 45 Dg. |
| 69 | Door Bend 87.5Dg. |
| 70 | Single `Y' with Door |
| 71 | Socket Plugs |
| 72 | Pipe Clip |
| 73 | WC Connector |
| 74 | WC connector (Bend) with ring |
| 75 | Single Tee |
| 76 | Multi Floor Trap |
| 77 | Gully Trap 160mm |
| 78 | Nahni Trap with Jali 4\\" |
| 79 | Vent Cowel 100mm |
| 80 | Providing & Laying P.V.C. / XLPE insulated & P.V.C. sheathed Un-armoured Copper cable confirming to IS:1554 P-I / IS :7098 P - I of 1.1 KV with electrolytic grade Copper made of copper rods confirming to IS 613-1964, of purity >99.7 %, Inner / outer sheath confirming to IS:5831 in existing RCC / Hume / Stoneware / PVC pipe/ open duct/cable trench / Cable tray (with cable tie) including testing etc. as required of following size. OEM must have it's own in house NABL accrediated Laboratory for testing procedure as per IS:10810 For additional technical parameters of product / work refer Annexure 'A' attached with this BSR |
| 81 | 2 core 1.5 sq mm |
| 82 | 3 core 2.5 Sq. mm |
| 83 | 3 core 4.0 Sq. mm |
| 84 | 4 core 6.0 Sq. mm |
| 85 | 4 core 16.0 Sq. mm |
| 86 | Providing & Laying P.V.C. / XLPE insulated & P.V.C. sheathed Arrmoured Aluminium cable confirming to IS:1554 P-I / IS :7098 P - I of 1.1 KV with H4- Grade electrolytic aluminium conductor confirming to IS 8130 of purity >99.6 %, round / flat strip armouring of cables, Inner / outer sheath confirming to IS:5831 in existing RCC / Hume / Stoneware / PVC pipe/ open duct/cable trench / Cable tray(with cable tie) including testing etc. as required of following size. OEM must have it's own in house NABL accrediated Laboratory for testing procedure as per IS:10810.For additional technical parameters of product / work refer Annexure 'A' attached with this BSR 3.5 core 120.0 Sq. mm |
| 87 | Supply and installation of spike of M.S. rod 20mm dia 3.0mtr. long for earthing of (tower/pole) drive into earth by mechanical means sturcture connection the spike with cross arm top hamper PCC pole, lattics tower to earth etc. complete as per technical specification of DISCOM. |
| 88 | Providing & Fixing of 240/415 V AC MCB with positive isolation of 10 kA breaking capacity (B/ C/D tripping characteristic as per type of load and site requirement) 4 KV impulse withstand voltage, ISI marked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC 60947-2, low watt losses, trip free mechanisum , energy limiting of class 3 as per IEC, minimum phase termination capacity of 35sq.mm. , conductor line load reversibility , IP 20 contact protection and fitted in existing distribution board/sheets, minimum electrical operation 20,000 upto 20 A rating and 10,000 upto 63 A, 5000 for 80 A & above rating including making connections, testing etc. as required. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test reports & All as per pre approved by Engineer in charge. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR 100 A rating Single pole MCB (With B/C curve tripping Characteristics) |
| 89 | Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor as per PWD specification for electrical Works with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from 99.90 % purity copper, class 5 stranding in acc. to IS:8130/IEC 60228 for lower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5, in existing surface or recessed PVC/ MS conduit/casing capping making connections with Copper Lugs of suitable size, Ferrules,testing etc. as required. OEM Must have its own in house NABL lab setup for all testing facilities for wires. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR |
| 90 | 2 x 1.5 sq.mm |
| 91 | 2 x 4.0 sq.mm |
| 92 | 2 x 2.5 sq. mm. + 1x1.5sqmm |
| 93 | 1 x 1.5 sq.mm |
| 94 | S&F following sizes (dia.) of ISI marked virgin material MMS ( IS:9537 P - III ) PVC conduit along with ISI marked (IS:3419-1988) accessories as required in recess including cutting the wall, covering conduit and making good the same as required. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR 25mm |
| 95 | Providing & Fixing of Recessed/surface mounting heavy duty horizontal type Double Door ( Metal / Glazed )Distribution board with Metal end box made out from Galvanized steel / CRCA sheet not less then 1.2 mm thick conforming to IS-8623-1 & 3 / IEC 61439- 1 & 3, powder painted complete with reversible door (for double door DB only )100 amp. insulated copper bus bar/shorting link , copper neutral link, copper earth link , color coded interconnecting wire set of suitable rating and din bar,masking sheet, making internal DB terminations with copper lugs, Ferrules, detachable gland plate, including making connections, testing etc. as required. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test reports & All as per pre approved by Engineer in charge. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR |
| 96 | Metal door (single phase) IK-09 and IP-43 with Metal end box 12 Way (12+2) |
| 97 | Metal door (Three phase) IK-09 and IP-43 with Metal end box 12 Way |
| 98 | SITC of 3 /4 pole current limiting Moulded case circuit breaker (MCCB) made of flame retardent & heat resistant material having following current rating, short circuit breaking capacity at 440/415 V, 50 Hz; O/L & S/C settings , conforming to IS/IEC 60947 P -2 :2003 with front face and centralised adjustable, trip free mechanisum, true contact position indicator, line load interchangeability, designed for both horizontal & vertical mounting without any adverse effect on electrical performance, suitable for operation upto 55 degree and without derating upto 40 degree, pollution degree 3, having positive isolation capability, push (test) to trip, trip time less then 10 ms under s/c condition, Breaking capacity Ics = 100% Icu. U imp =8 KV, rated insulation voltage 690 V. provision for UVR , shunt trip , earth fault trip, door interlock, pad lock & rotary handle , including making connections etc. as required.OEM shall have submit NABL / CPRI / ERDA accrediated lab type test certificate before execution All as per pre approved by Engineer in charge. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR 4 pole MCCB With Thermal Magnetic release |
| 99 | 125 Amp , 25 kA, adjustable O/L & adjustable S/C setting, |
| 100 | 160 Amp , 25 kA, adjustable O/L & adjustable S/C setting, |
| 101 | Plate Earthing as per IS:3043 with Hot dipped G.I. Earth plate of size 600mm x 600mm x 6.0mm by embodying 3 to 4 mtr. below the ground level with 20 mm dia. G.I. 'B' class watering Pipe ,including all accessories like nut, bolts, reducer, nipple, wire meshed funnel, and Heavy duty weather proof poly-propylene earth pit chamber with lockable Jam free lid suitable for safe working load 5000 Kg or more of size Top Dia. 225 to 260 mm, Bottom Dia 300 to 350 mm. and Height 250 to 300 mm. and embodying the pipe complete with alternate layers salt and coke/ charcoal, testing of earth resistance for value of 5 ohms or less as required & must record by engineer in charge during site visit and ensure to enter in measurment book.All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR . |
| 102 | Supply & Laying following size earth wire in horizontal or vertical run in ground/surface/recess including riveting, soldering, saddles, making connection with GI/Cu purity purity >95% thimble etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR 6 SWG G.I. ( Hot Dipped ) Wire |
| 103 | Providing & Fixing of of Double ball bearing, copper wounded capacitor start single phase metallic blade fresh air fan, in existing opening including cost of hardware , flexible 3 core copper conductor ,making connections, testing etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR 300 mm sweep |
| 104 | Providing & Fixing of 450 mm Sweep Oscillating type Wall mounting / Pedestal type fans with Three speed, ON and OFF position, Sintered Iron bush oil impregnated, with metal front and back 120 or more ribs guard; Three no. Aluminium blades, minimum Air delivery 100 Cum. / Minute , Minimum Service Value 1.11 Cum./min/watt, noise level should be <= 75 dB, power consumption <= 120 watts, motor protection through thermal overload protection device, including fixing with anchor bolts, making connection testing etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR Wall mounting type with Adjustable Vertical Angle |
| 105 | Providing & Fixing of energy efficient /energy saving IP 20 LED direct retrofit Bulb in existing holder or fixture as required with system lumen efficacy ≥100 lm/Watt output ,pf 0.95 , CRI >70, minimum life time of minimum 25000 Burning Hours with , 70% of intial Lumen maintaned till life ends , CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin) , maximum power consumption should not more than the specified rating and Fixture shall be of BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) certificate / Report from OEM shall be submitted. All as per pre approved by engineer in charge . for additional technical parameters of product/ work, refer Annexure \\"A\\" attacheded with this BSR 18/20 Watt |
| 106 | Wiring of light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) in recessed ISI marked MMS ( IS:9537 P - III ) virgin material PVC conduit & it's ISI marked (IS:3419-1988) accessories, round tiles, 1.2 mm thick Hot Dipped Galvanized Modular Box with earth terminal, 10A Modular switch,Modular face plate with grid plate, 3 pin ceiling rose / Holder /3 way connector, screws, making connections, testing etc. as required. For specification of copper Conductor, Phenolic Laminated sheet's & Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07 For additional technical parameters of product / work refer Annexure 'A' attached with this BSR |
| 107 | Short point (up to 3 mtr.) |
| 108 | Medium point (up to 6 mtr.) |
| 109 | Long point (up to 10 mtr.) |
| 110 | Supply , Installation, Testing and Comissioning of Inverter type Air Cooled Hi Wall split type Air conditioners with latest star rating system as per BEE amended upto date complete with Indoor unit(IDU), Out door unit (ODU), surface / concealed copper Refrigerant piping with insulation (closed cell elastomeric nitrile rubber tubular pipe section) upto 3 Mtr (IDU to ODU), copper power cable upto 3.5 Mtr (IDU to ODU), R-32/R-410 Green Refrigerant, wireless Remote control, suitable for working between 230V +/- 10% with low & high voltage cutoff and 50 hz , single phase AC supply capable of performing cooling, dehumidification, air circulation of following capacity with Scroll / rotary compressor. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR 2.0 TR ISEER not less then 4.6 |
| 111 | Supply & fixing MS powder coated stand suitable for 1.0/1.5/ 2.0 Tr outdoor type of Split AC. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR . |
| 112 | Supply, Fixing and testing of following capacity ISO certified company made wall mounted stabilizer having output voltage variation from 200 V to 250 V(+/-5%) with input voltage variation from 170 V to 260 V, time delay facility from 2 to 4 minute and high cutoff at 270 V with providing of 16 Amp /20 Amp Industrial plug top making connection etc complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR 5KVA |
| 113 | Providing and laying M30 grade controlled cement concrete pavements including mixing and vibrations concrete with necessary needle vibrators and surface with screed board vibrating complete in all respect with 20/25 mm stone aggregate (crusher broken) including anti-skid textured finish to required camber/ super elevation and grade including curing etc. as per specification with cement concrete M-30 grade including cost of Steel frame work for sides of C.C. pavement consisting of M. S. channels flats and angles with required steel pegs ( some of them may left embedded in concrete/ including providing frame work) |
| 114 | Extra for vacuum processed concrete including cost of equipments labour etc. |
| 115 | Consultancy work for the development Indore stadium City. It includes preparation of Architectural, Structural, Electrical, Plumbing, Sanitary Design & Drawings etc. required for the construction of following Buildings in the stadium:The consultancy work includes Vetting of structural design & drawings from IIT/NIT/Govt. Engineering College. Provide working drawing and As built drawings. All work done as per direction of Engineer in charge. |
| 116 | Providing & fixing Self supported truss less roof system using Base Metal of Cold Rolled Structural Quality Steel Sheets of min. grade D-350 Mpa yield strength ( as per ASTM A-792) having Base Galvalume Coating of AZ 150,150 gms/sqm including fabrication, panel formation, mechanical sealing and erection with proper provision of skylight, hangers, turbo ventilator exhaust system, anchoring with RCC gutter Beams etc complete in all respect as per manufacturer's specification and direction of Engineer-in-charge (excluding cost of skyligh, turbo ventilator exhaust & RCC gutter beams) For BMT of 1.60 mm |
| 117 | 30 mm Thick Interlocking Modular Sports Mat :----Providing, supplying, transporting, laying, fitting, and commissioning of 30 mm thick interlocking modular sports mats complete in all respects for indoor sports facilities wrestling . Technical Specifications :-- MaterialHigh-density EVA Foam/Tatami-type sports mat.Non-toxic, odor-free, eco-friendly material.Water-resistant and moisture-resistant.Anti-skid textured surface.DimensionsStandard tile size: 1000 mm × 1000 mm (±5%).Thickness: 30 mm.Performance RequirementsExcellent shock absorption and impact resistance.Comfortable cushioning for sports and training activities.High wear resistance and durability.Physical PropertiesDensity: Minimum 90 kg/m³.Compression resistance suitable for sports applications.Anti-slip surface finish.Easy to clean and maintain.Color approved by the Engineer-in-Charge.Mats shall be laid uniformly with tight interlocking joints.Finished surface shall be free from gaps, unevenness, and visible defects.Manufacturer's test certificate shall be submitted.Material shall be free from cracks, warping, deformation, or manufacturing defects. Warranty Minimum 1 year warranty against manufacturing defects and premature failure. |
| 118 | Wrestling Court PVC Flooring:-- Providing, Supplying and Installing PVC Wrestling Mat Flooring System for Indoor Sports Hall.The work shall include supply, transportation, laying, fixing, testing and commissioning of a complete wrestling mat flooring system conforming to the latest standards of Wrestling Federation of India (WFI) / United World Wrestling (UWW).Technical Specifications :--Sports-grade homogeneous PVC sheet.Thickness: Minimum 6 mm.Anti-skid embossed surface finish.Wear-resistant, anti-bacterial and anti-fungal properties.Easy to clean and maintain.Shock Absorbing LayerHigh-density EVA/XPE foam. Thickness: Minimum 70 mm.Density: Minimum 90 kg/m³.Uniform cushioning and impact absorption.Excellent shock absorption.High dimensional stability.Tear and puncture resistance.Non-toxic and environmentally safe material.Fire-retardant properties.Minimum 5-year warranty against manufacturing defects, delamination and premature wear. |
| 119 | Boxing Court EVA Foam Flooring : Providing, Supplying and Installing 25 mm Thick High-Density EVA Foam Flooring System for Boxing Court.The work shall include supply, transportation, laying, fixing and installation of high-density EVA foam flooring complete in all respects.MaterialEthylene Vinyl Acetate (EVA) closed-cell foam.Free from harmful substances and suitable for indoor sports applications.ThicknessMinimum 25 mm uniform thickness.DensityMinimum 90 kg/m³.High resilience and excellent impact absorption characteristics.Closed-cell structure.High shock absorption and energy dissipation.Moisture resistant and non-water absorbent.Anti-fungal and anti-bacterial.Good dimensional stability and durability.Non-toxic and odorless.WarrantyMinimum 3 years against manufacturing defects. |
| 120 | Heavy-Duty PVC Flooring for Boxing CourtName of WorkProviding, supplying and laying heavy-duty PVC sports flooring system for Boxing Court/Training Area complete in all respects.The work shall include supply, transportation, laying, fixing, testing and commissioning of heavy-duty PVC sports flooring over shock-absorbing underlayer, including all accessories, adhesives, joint treatment and finishing as required.PVC Sports FlooringMaterial: Sports-grade heavy-duty homogeneous/multi-layer PVC sheet.Thickness: Minimum 8 mm.Surface Finish: Anti-skid embossed texture.Wear Layer: Factory-finished wear-resistant layer.Properties:Abrasion resistantAnti-fungal and anti-bacterialMoisture resistantUV stabilizedFire retardantEasy to clean and maintainMinimum 5 years warranty against manufacturing defects, delamination, cracking and premature wear. |
| 121 | Supply of movable badminton poles:--- providing of movable badminton poles made of 47 mm X 47 mm MS pipe, 65 to 70 kg counter weight on each side, the wheels diameter 100 mm , complete with rubber feet to protect the playing surface and grip on floor, poles are powder coated or spray painted. It includes supply and fixing of Garware badminton net size 6.10 m in length and 0.76 m height, color black, tournament quality |
| 122 | Providing &fixing (BWF Approved) multi layered PVC sports floor covering material available in sheets 1.8 m wide with a compact closed cell foam backing, glass fibre reinforcement, vinyl performance layer, embossed PVC wear layer and printed wood design protected by a transparent wood grain embossed wear layer, having standard BS EN 429 sports flooring, with properties of friction, shock absorption, vertical deformation and resistance to rolling load with special treatment have vertical ball behaviour, no wax no polish for life, sure clean and glass fibre grid reinforcement, having thickness not less than 7.00mm having standard EN428 with wear layer 0.65mm/0.8 having standard EN 429, 4.48kgs/m2, ASTM 7-410 art weight as per standard EN 430 (i.e. 3.39kgs/m2) available sheet size width 1.8mtr and length 15m covering surface area 27 sqm. As per standard BS EN 429 having technical characteristics of Friction 108 (Pass), Shock absorption 30% (Pass), Vertical Deformation (Pass), Vertical Ball Behaviour>98 (Pass), Resistance to rolling load (Pass). Sound insulation ENISO717-2 pass, Resistance to indentation test method Shao A (Pass). As per standard impact resistance DIN18032 (PASS) BWF Approved including fixing with Pidilite SR-998 Rubber Adhesive over existing smooth levelled & completely smooth and moisture free hard cement concrete surface including jointing with electric welding machine with matching welding rods for perfect joints including line marking with Vapoured Epoxy paint as per manufacture specifications complete work should be done as per direction and entire satisfaction of engineer in charge. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 21, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 10, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 18 daysAug 11, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 19 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender