Tender For Construction of Balance Work I.E. Lecture Theatre, Examination Hall Including Under Pass For Students In Parking Block Opposite To Auditorium Block At Medical College Igmc Shimla.
Tender Value
Ref. Documents
Estimated cost
Bid Submission
28 Jul 2026
1 days left
EMD
9.65 Lakhs
Bank guarantee accepted
Document Fee
7000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Shimla → Himachal Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Construction of Balance Work I.E. Lecture Theatre, Examination Hall Including Under Pass For Students In Parking Block Opposite To Auditorium Block At Medical College Igmc Shimla.
BOQ
| Sl. No. | Item Description |
| 1 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge.Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) |
| 2 | Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as perdirection of Engineer - in- charge. |
| 3 | Dismantling steel work in single sections including dismembering and stacking within 50 metres lead in: Channels, angles, tees and flats |
| 4 | Earth work in foundation or cutting by mechanical means (Hydraulic excavator)/ manual means in all heights and depths in all kinds of soil including saturated soils comprising of pick work, jumper work and blasting work both in soft and hard rock with chiesling and wedging out of rock (where blasting is prohibited and their intermediate classifications soils including dewatering where ever required, setting out to required lines, levels as shown on the drawing and directed by the Engineer-in-charge at site, according to the CPWD specification and sorting out useful and unuseful material and transportation of the unuseful material for disposing of all surplus earth at dumping site including prescribed dumping charges (which will be arranged by the contractor himself at his own cost within MC area or out site on private land) to the satisfaction of Engineer-in-Charge through all modes of transportation including head load, animal load or mechanical means along with its levelling fine dressing and with all kinds of labour machineries, tools equipments and safety measures and incidentals necessary to complete the work wise mechanical means and labour (if required) all useful material such as stones,shingles aggregate and slates shall be properly stacked at site to the meximum possible extent in all leads and lifts through all modes of transportation and used/removed as per the direction of Engineer-in-charge. Any loss to the public and private property during the course of execution and disposal of serviceable and unserviceable materials shall be the absolute responsibility of the contractor and shall have to be duly compensated by him in all respect including all incidental charges:- :- All kinds of soil. |
| 5 | Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 6 | Centering and shuttering including strutting, propping etc. and removal of form for : Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 7 | Centering and shuttering including strutting, propping etc. and removal of form for : Suspended floors, roofs, landings, balconies and access platform complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 8 | Centering and shuttering including strutting, propping etc. and removal of form for :Lintels, beams, plinth beams, girders, bressumers and cantilevers complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 9 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand) : 8 graded stone aggregate 40 mm nominal size) complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 10 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand) : 6 graded stone aggregate 20 mm nominal size) complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 11 | Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. All works upto plinth level |
| 12 | Providing and applying shotcrete concrete of nominal mix 1:1.5:3 (cement : fine sand : coarse aggregate) using approved materials, applied pneumatically under pressure on prepared surfaces, including cleaning of surface, removal of loose material, wetting, machine mixing, conveying, spraying through hose and nozzle, finishing to required line, level and thickness, curing complete, including cost of all labour, materials, machinery, compressor, scaffolding, tools, plants, wastage and rebound loss, complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 13 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete Thermo- echanicallyTreated bars of gradeFe-500D or more.complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 14 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in super structure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:4 (1 cement : 4 coarse sand) complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 15 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:3 (1 cement :3 coarse sand) complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 16 | Stone soling hand packed under floor of selected hard stone as per the directions of Er. In Charge including all kinds of leads, lifts and all kinds of leads, lifts etc.complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 17 | Stone filling behind abutment, wing wall and return wall complete as per drawings, Design & technical specification Clause 1204.3.8 complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 18 | Providing weepholes in Brick masonry / stone masonry / plain / reinforced concrete abutment, wingwall, return wall with 100mm dia PVC pipe extending through the full width of the structures with slope of 1(V):20(H) towards drawing face complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 19 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately). 1st class Deodar wood. |
| 20 | Providing and fixing flush door shutters interior grade, commercial type, core of black-board construction with frame of first class hard wood and well matched commercial ply veneering with vertical grains of cross bands andface veneers on both faces of shutters. 40 mm thick including black enamelled M.S. butt hinges. complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 21 | Providing and fixing bright finished brass handles with screws etc. complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.: 125 mm |
| 22 | Providing and fixing bright finished brass handles with screws etc. complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.: 100 mm |
| 23 | Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. : 250x10 mm |
| 24 | Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. : 200x10 mm |
| 25 | Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. : 300x16 mm |
| 26 | Providing and fixing bright finished brass 100 mm mortice latch and lock, ISI marked, with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868) aluminium lever handles of approved quality with necessary screws etc. complete.complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 27 | Providing and fixing bright finished brass hard drawn hooks and eyes : complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. 300 mm |
| 28 | Providing and fixing150 mm bright finished floor brass door stopper with rubber cushion, necessary brass screws etc. to suit shutter thickness complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 29 | Providing built up UPVC casement windows profile specifications:- Zendoe series: Outer frame-12601 (70 mm x64 mm). Sash-12617 (70mmx70 mm) Z Mullion - 3086 (70 mm x 50 mm), Coupling-12358 (70mm) including shutters with chember thickness 2.60 mm and Gl frame thickness 1.20 to 2.00 mm and 6 mm + 12 mm +6 mm DGU toughned glass gap filled with argon gas fixed with thermoplastic elastomer (TPE) gasket, Wire mesh panels grills - George bars etc, complete including Zinc alloy casement handle, Friction Stay/2D hinges/ butt hinges, espag multipoint locking system, locking strickers complete in all leads and lifts complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 30 | Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. : 5.5 mm thick glass panes |
| 31 | Providing and fixing double glazed hermetically sealed glazing in aluminium windows, ventilators and partition etc. with 6 mm thick clear float glass both side, having 12 mm air gap, including providing EPDM gasket, perforated aluminium spacers, desiccants, sealant (Both primary and secondary sealant) etc.complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 32 | Filling the gap in between aluminium/ stone/ wood frame and adjacent RCC/Brick/ Stone/ wood/ Ceramic/ Gypsum work by providing weather/structural non sag elastomeric PU sealant over backer rod of approved quality as per architectural drawings complete including carriage of materials in all leads and lift as per direction of Engineer in Charge., complying to ASTM C920, DIN 18540- F & ISO 11600 Upto 5 mm depth and 5 mm width |
| 33 | Providing and fixing casement handle made of zinc alloyed (white powder coated) for uPVC casement window with necessary screws etc. complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 34 | Providing and fixing zinc alloyed (white powder coated) touch lock for uPVC sliding window with necessary screws etc. complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 35 | Providing and fixing plain lining with necessary screws/nuts & bolts/ nails, including a coat of approved primer on one face, and fixed on wooden /steel frame work, complete as per direction of Engineer-in- charge (Frame work shall be paid for separately). 12mm thick commercial ply conforming to IS : 1328 BWR type complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 36 | Providing and fixing thermal insulation with Resin Bonded Fibre glass wool conforming to IS: 8183 having density 24 kg/m3, 50 mm thick, wrapped in 200G Virgin Polythene Bags fixed to wall with screw, rawel plug & washers and held in position by criss crossing GI wire etc. complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 37 | Providing and fixing of ACOUSTICAL PANEL wall 18 mm thick HDMR (High Density Moisture Resistant) board of approved make and quality, conforming to relevant IS standards, fixed on G.I studs 600x600mm centre to centre 2400mm X 50mm web thickness 0.5mm, flanges 15 & 50mm fully knurled giving it high strength, hot dipped galvanized steel with 120GSM zinc coating specially designed for Acoustic vibration management and long life complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 38 | Providing and Fixing of ACOUSTICAL PANEL‘Wooden Slats’ wall 2430*131 mm with thickness of 16 mm MDF backed with acoustical Fleece providing sound absorption of NRC 0.70 tested as per IS:8225-1987 (Equivalent to ISO: 354-1985 & ASTM 423-90).To be installed with 15mm Aluminium profile conforms to Aluminium Alloy 6063-T 6.Temper As per BS:1474-1987 and G.I Lock in clips on the back of tongue and Groove system. The density per panel is 750-800 kg/m3.The panels come with tongue & groove for seamless patterns,2-14mm / 28-4 mm Groove and visible panel. Wooden slats are made from acoustical fibreboard with linear perforations for excellent uniformity. The perpendicular holes are available on the back of panel which are covered by black acoustical fleece. INSTALLATION Chord’s ‘Wooden Slats’ can be installed on G.I studs 600x600mm centre to centre 2400mm X 50mm web thickness 0.5mm, flanges 15 & 50mm fully knurled giving it high strength, hot dipped galvanized steel with 120GSM zinc coating specially designed for Acoustic vibration management and long life with a backing of 1000 GSM Acoustic Wool tested as per Fire Retardant ASTMD 635-1991/Insulation and IS 15061 2002 for excellent results.complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 39 | Product: Stretch Fabric NRC 1.0 Full System Providing and fixing of ACOUSTICAL wall PANEL “Stretch Fabric full System” with ’Aphony Fibrette’ 600x1200x20mm tile made with wood fibre 1mm width cement composites tile. Fabric colour as per Architect/Client choice. Acoustical infill of 300 GSM absorb wool thickness 10mm which is adhered to the acoustical panel on the front side. Then 12mm Vinyl tracks are screw fixed on the 8 mm thick and 50mm wide ply strips. Then the fabric is stretched over the Vinyl tracks. The installed system should provide NRC of 1.0. Aphony fibrette Anti Bacterial test as per JIS-Z2801-2010. to be installed on G.I studs 600x600mm centre to centre 2400mm X 50mm web thickness 0.5mm, flanges 15 & 50mm fully knurled giving it high strength, hot dipped galvanized steel with 120GSM zinc coating specially designed for Acoustic vibration management and long life with a backing of 1000 GSM absorb wool tested as per Fire Retardant ASTMD 635-1991/Insulation and IS 15061 2002 for excellent results.complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 40 | Providing and fixing composite glass wool wall panels of size 2400 × 1220 × 15 mm for lining to ceiling only, made of glass wool of minimum density 24 kg/m³, faced with factory-laminated aluminium foil / black tissue, fixed directly to existing ceiling surface with approved adhesive and GI insulation pins, including cutting, placing, joint alignment, sealing joints with aluminium tape, complete in all respects as per approved drawings, manufacturer’s specifications, and direction of Engineer-in-Charge. |
| 41 | Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality.complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. 1.0 mm thick |
| 42 | Providing and fixing plain lining with tongued and groved jointing and screws (frame work and cover fillets to be measured and paid for separately with. 1st class indian teak wood. complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. 20mm thick |
| 43 | Providing and fixing T-15 PPGI pre painted galvanised perforated metal tiled false ceiling of specified materials of size 595x595 mm and 0.5 mm thick with 8 mm drop; made of GI sheet having galvanizing of 100 gms/ sqm (both sides inclusive) and 20% perforation area having NRC (Noise Reduction Coefficient ) of 0.5, electro statically polyester powder coated after bending and perforation, and backed with a coloured acoustic fleece 5.-60 micron.in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections consisting of main \\"T\\" runner with suitably spaced joints to get required length and sheet, spaced at requer distance center to center and cross \\"T\\" spaced between main \\"T\\" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross \\"T\\" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main \\"T\\" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long bullet fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. GI Metal Ceiling Lay in perforated Tegular edge global white color tiles of size 595x595 mm and 0.5 mm thick with 8 mm drop; made of GI sheet having galvanizing of 100 gms/ sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holes and having NRC (Noise Reduction Coefficient ) of 0.5, electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation, and backed with a black Glass fiber acoustical fleece.complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 44 | Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system of structural glazing (with open joints) for linear as well as curvilinear portions of the building for all heights and all levels, including: (a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design. (b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (No 0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc.(c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium item.s The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete, as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places.complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 45 | Providing and fixing wooden plank ceiling with tongued and grooved jointing and wood screws (frame work and cover fillets to be measured and paid for separately)First class indian teak wood.complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. 20 mm thick |
| 46 | Providing and fixing composite glass wool false ceiling made of minimum 25 mm thick glass wool slabs (density 24 kg/m³), faced with factory-laminated aluminium foil / tissue, laid over and including GI frame system comprising of GI perimeter channel (0.55 mm thick) fixed to wall with dash fasteners, GI intermediate channel (0.90 mm thick) suspended from soffit with GI hangers / adjustable rods, complete with connecting clips, screws, anchors, and including cut-outs for light fixtures, AC diffusers, complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 47 | Providing and Fixing 15 mm thick densified tegular edged eco friendly light weight calcium silicate false ceiling tiles of approved texture of size 595 x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanised steel sections (galvanising @120 grams per sqm including both side) consisting of main ‘T’ runner suitably spaced at joints to get required length and of size 24x38 mm made from 0.33 mm thick (minimum) sheet, spaced 1200 mm centre to centre, and cross “T” of size 24x28 mm made out of 0.33 mm (Minimum) sheet, 1200 mm long spaced between main’T’ at 600 mm centre to centre to form a grid of 1200x600 mm and secondary cross ‘T’ of length 600 mm and size 24 x28 mm made of 0.33 mm thick (Minimum) sheet to be inter locked at middle of the 1200x 600 mm panel to from grid of size 600x600 mm, resting on periphery walls /partitions on a Perimeter wall angle pre coated steel of size(24x24X3000 mm made of 0.40 mm thick (minimum) sheet with the help of rawl plugs at 450 mm centre to centre with 25 mm long dry wall screws @ 230 mm interval and laying 15 mm thick densified edges calicum silicate ceiling tiles of approved texture in the grid, including, cutting/ making opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc., wherever required. Main ‘T’ runners to be suspended from ceiling using G.I. slotted cleats of size 25x35x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm G.I. adjustable rods with galvanised steel level clips of size 85 x 30 x 0.8 mm, spaced at 1200 mm centre to centre along main ‘T’, bottom exposed with 24 mm of all Tsections shall be pre painted with polyster baked paint, for all heights, as per specifications, drawings and as directed by Engineer-in Charge. Note :- Only calcium silicate false ceiling area will be measured from wall to wall. No deduction shall be made for exposed frames/ opening (cut outs) having area less than 0.30 sqm.The calcium silicate ceiling tile shall have NRC value of 0.50 (Minimum), light reflection > 85%, non- combustible as per B.S. 476 part IV, 100% humidity resistance and also having thermal conductivity <0.043 w/ mK complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 48 | Providing and fixing plain square edged cover fillets (beading) 60mmx12mm section with wood screws in ceiling and lining including mitring at junctions. complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. 1st class indian teak wood. |
| 49 | Providing and fixing plain square edged cover fillets (beading) 50mmx12mm section, with wood screws in ceiling and lining including mitring at junction. 1st class deodar wood. |
| 50 | Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.: Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. |
| 51 | Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all comcomplete including carriage of materials in all leads and lift as per direction of Engineer in Charge. : crips grey |
| 52 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. Size of Tile 1200x1800 mm |
| 53 | Providing and laying ANTISKID vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc.complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.Size of Tile 600x600 mm |
| 54 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 55 | Stone tile work for wall lining upto 10 m height with special adhesive over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand), including pointing in white cement with an admixture of pigment to match the stone shade. 8 mm thick (mirror polished and machine cut edge)complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. Granite stone of any colour and shade |
| 56 | Stone granite tile work for wall lining upto 10 m height with special adhesive over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand), including pointing inwhite cement with an admixture of pigment to match the stone shade. 8 mm thick (mirror polished and machine cut edge) complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. crips grey |
| 57 | Providing edge moulding to18 mm thick marble stone counters, Vanitiesetc., including machine polishing to edge to give high gloss finish etc. complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.. Granite work |
| 58 | Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. 25 mm thick |
| 59 | Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 60 | Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. 40 mmthick C.C. paver block of M-30 grade with approved color design and pattern. |
| 61 | Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand.complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.. 60 mmthick C.C. paver block of M-30 grade with approved color design and pattern. |
| 62 | Providing and fixing in wall lining medium density fibre board IS: 14587:1998 marked, Pre-laminated one side decorative lamination and other side balancing lamination, with necessary fixing arrangement and screws etc.complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. 18 mm thick. |
| 63 | Fixing of Silent board in the thickness of 22mm made of 3 Compressed Wood Fiber Cement Composites 1200Kg/m. The silent board will be directly mechanically screwed on Sound Proof Ply 8 mm along with sealant and dampner tape in order to properly seal floor with joints epoxy acoustic sealant and dampner tape will be used to avoid any sound leakage. complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. To be installed with the help of hardware. |
| 64 | Providing and fixing 6 mm thick heavy-duty homogeneous PVC flooring of approved make and shade, laid over prepared, smooth and level sub-base using approved adhesive, including cutting, fitting, matching patterns, rolling with heavy roller to remove air pockets, finishing the joints, and all necessary materials, labour, tools and tackles, complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 65 | Structural steel work in single section, fixed with or without connecting plate,including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 66 | Providing and fixing 18 mm thick High Pressure Compact Laminate (HPL) toilet cubicle partitions of approved make (Marimo or equivalent), manufactured from high-density solid grade laminate, waterproof, termite-proof, anti-bacterial and scratch-resistant, comprising partition panels, doors and pilasters complete with SS 304 grade satin finish hardware including hinges, thumb turn lock with emergency release, coat hook, door stopper, indicator bolt, adjustable pedestal feet, top rail, aluminium/U-channel sections, all necessary fittings, fixtures, cutting, drilling, sealing, fixing with approved fasteners and making good the adjoining surfaces, complete in all respects as directed by the Engineer-in-Charge. |
| 67 | Providing and fixing factory manufactured acoustic door complete with door frame, acoustic door shutter, mineral wool/rockwool insulated core, perimeter acoustic seals, automatic drop seal at bottom, SS hinges, mortice lock, door closer, all necessary hardware and fittings, finished with decorative laminate/veneer on both faces, complete in all respects as per approved drawings and directions of the Engineer-in-Charge. |
| 68 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 69 | Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer. complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.M.S. tube |
| 70 | Providing and fixing 75 mm x 60 mm rounded hand rails in straight length complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.1st class deodar wood. |
| 71 | Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6 mm, with 40 mm dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer. |
| 72 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.63 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 73 | Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+ 0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 1518 microns using self drilling/ self tapping screws complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. : Ridges plain (500 - 600mm) |
| 74 | Providing valleys of 90 cm wide overall in plain G.S. sheet fixed with polymer coated J, or L hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete : 1.60 mm thick with zinc coating not less than 350 gm/m²complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 75 | Providing and fixing 15 cm wide, 45 cm overall semi-circular plain G.S. sheet gutter with iron brackets 40x3mm size, bolts, nuts and washers etc., including making necessary connections with rain water pipes complete. 0.63 mm thick with zinc coating not less than 275 gm/m² complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 76 | Providing and fixing M.S. BP Sheet 2mm thick in eaves board/facia/soffits/ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instruction of Engineer-in-charge (Base members of steel work shall be measured & paid separtely)complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 77 | Providing and fixing HPL Sheets 6mm thick in eaves ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instruction of Engineer-in-charge (Base members of steel work shall be measured & paid separtely)complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 78 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. 110mm dia pipes |
| 79 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.110 mm |
| 80 | 15 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement : 5 coarse sand) finished with a top layer 6 mm thick cement plaster 1:6 (1 cement : 6 fine sand).complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 81 | 6 mm cement plaster to ceiling. (a) in cement mortar 1:3 (1cement:3 mortar)complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 82 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 83 | Applying priming coat on new concrete/masonry/asbestos cement/ plastered surfaces after and including preparing the surface by thoroughly cleaning oil,grease,dirt and other foreign matter and sand papering as required with : complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. Readymixed primer |
| 84 | Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives. New work (Two or more coats applied @ 1.43 litre/ 10 sqm. Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm.complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 85 | Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr /10 sqm complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 86 | Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 87 | French spirit polishing : Filling: Applying matching wood filler/putty to seal all pores, cracks, and nail holes, followed by fine sanding. Sealing: Applying of high-quality wood sealer, including intermediate fine scuffing between coats to achieve a non-porous base. complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. One or more coats on old work |
| 88 | Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufacture complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 89 | Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earthwith lead upto 50 metres complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.. |
| 90 | Supplying Laying, spreading and compacting stone aggregate of specified sizes to WBM specifications in uniform thickness, hand picking, rolling with 3 wheeled road/vibratory roller 8-10 tonne capacity in stages to proper grade and camber, applying and brooming requisite type of screening / binding material to fill up interstices of coarse aggregate, watering and compacting to the required density . 90 mm to 45 mm size stone aggregate G I complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 91 | Supplying Laying, spreading and compacting stone aggregate of specified sizes to WBM specifications in uniform thickness, hand picking, rolling with 3 wheeled road/vibratory roller 8-10 tonne capacity in stages to proper grade and camber, applying and brooming requisite type of screening / binding material to fill up interstices of coarse aggregate, watering and compacting to the required density 63 mm to 45 mm size stone aggregate G II complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 92 | Supplying Laying, spreading and compacting stone aggregate of specified sizes to WBM specifications in uniform thickness, hand picking, rolling with 3 wheeled road/vibratory roller 8-10 tonne capacity in stages to proper grade and camber, applying and brooming requisite type of screening / binding material to fill up interstices of coarse aggregate, watering and compacting to the required density . 53 mm to 22.4 mm size stone aggregate GIII complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 93 | Providing and applying tack coat using bitumen emulsion conforming to IS:8887, using emulsion pressure distributer including preparing the surface & cleaning with mechanical broom. On W.B.M / W.M.M. @ 0.4kg/sqm complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 94 | Providing and laying bituminous macadam using crushed stone aggregates of specified grading premixed with bituminous binder, transported to site by tippers, laid over a previously prepared surface with paver finisher equiped with electronic sensor to the required grade, level and alignment and rolling with smooth wheeled, vibratory and tandem rollers as per specifications to achieve the desired compaction and density, complete as per specificatons and directions of Engineer-in-Charge. 50 to 100 mm average compacted thickness with bitumen of grade VG-10 @ 3.50% (percentage by weight of total mix) prepared in Batch Type Hot Mix Plant of 100-120 TPH capacity.complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 95 | Providing and laying Bituminous concrete using crushed stone aggregates of specified grading, premixed with bituminous binder and filler, transporting the hot mix to work site by tippers, laying with paver finisher equiped with electronic sensor to the required grade, level and alignment and rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction and density as per specification, complete and as per directions of Engineer-in-Charge. 40/50 mm compacted thickness with bitumen of grade VG-10 @ 5.5% (percentage by weight of total mix) and lime filler @ 3% (percentage by weight of Aggregate) prepared in Batch Type Hot Mix Plant of 100-120 TPH capacity.complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 96 | Providing and fixing Polyethelene-Aluminium- Polyethelene PE-AL- PE Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 metre spacing. This includes testing of joints complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.. 1216 (16 mm OD) pipe |
| 97 | Providing and fixing Polyethelene-Aluminium- Polyethelene PE-AL- PE Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 metre spacing. This includes testing of joints complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.. 2025 (25 mm OD) pipe |
| 98 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. External work 20 mm nominal outer dia Pipes |
| 99 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.. External work 32 mm nominal outer dia Pipes |
| 100 | Providing and fixing Polyethelene-Aluminium-Polyethelene PE-AL-PE Composite tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 101 | Providing and fixing high pressure PVC Pipe of Kitec Multi Layer of composit pressure spigot and socket, waste and ventilating pipes ISI marked with collar and clamps including fixing with approved adhesive etc. complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.. 75mm |
| 102 | Providing and fixing high pressure PVC Pipe of Kitec Multi Layer of composit pressure spigot and socket, waste and ventilating pipes ISI marked with collar and clamps including fixing with approved adhesive etc. complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. 110mm |
| 103 | Providing and fixing PVC holder bat clamps of approved design PVC pipes embedded in and including cement concrete blocks 10*10*10cm (ten into ten into ten centimeter) of 1:2:4 (one cement isto two sand isto four graded stone aggregate 20mm (twenty millimeter) nominal size) and cost of cutting holes and making good the wall etc. as per HP.PWD / CPWD specification complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. 75mm |
| 104 | Providing and fixing PVC holder bat clamps of approved design PVC pipes embedded in and including cement concrete blocks 10*10*10cm (ten into ten into ten centimeter) of 1:2:4 (one cement isto two sand isto four graded stone aggregate 20mm (twenty millimeter) nominal size) and cost of cutting holes and making good the wall etc. complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. 110mm |
| 105 | Providing and fixing PVC ISI marked floor traps of self-cleaning design including fixing with approved adhesive complete including cost of cutting and making good the walls and the floors: complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.,(a) 110x 90 mm(one hundred ten into ninety milimeter. |
| 106 | Providing and fixing PVC single equal branch with oval access door , ISI marked insertion rubber washer 3 mm thick bolts and nuts complete including fixing with approved adhesive etc. complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.. 75mm |
| 107 | Providing and fixing PVC single equal branch with oval access door , ISI marked insertion rubber washer 3 mm thick bolts and nuts complete including fixing with approved adhesive etc. complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.. 110mm |
| 108 | Providing and fixing PVC door bend with oval acces door, insertion rubber washer 3 mm thick bolts and nuts ISI marked complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. 75mm |
| 109 | Providing and fixing PVC door bend with oval acces door, insertion rubber washer 3 mm thick bolts and nuts ISI marked complete including fixing with approved adhesive etc. complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.110mm |
| 110 | Providing and fixing PVC door tee ISI marked including fixing with approved adhesive etc. complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.. 75mm |
| 111 | Providing and fixing PVC door tee ISI marked including fixing with approved adhesive etc. complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.. 110mm |
| 112 | Providing and fixing PVC collars ISI marked including fixing with approved adhesive etc. complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.. 75mm |
| 113 | Providing and fixing PVC collars ISI marked including fixing with approved adhesive etc. complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.. 110mm |
| 114 | Providing and fixing PVC plain bend ISI marked including fixing with approved adhesive etc. complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.. 75mm |
| 115 | Providing and fixing PVC plain bend ISI marked including fixing with approved adhesive etc. complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.. 110mm |
| 116 | Providing and fixing PVC. 110mm size 'P' or 'S' Snow Cat. No. S9030101 White trap for water closet (squatting pan) including jointing the trap with the pan and and PVC pipe with approved adhesive etc. complete. (a) 110 mm dia |
| 117 | Providing and fixing PVC cowl complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.75mm |
| 118 | Providing and fixing PVC cowl complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.110mm |
| 119 | Providing and fixing vitreous wash water closet ( European Type - WC pan) Jaquar SLS-WHT-6751P180PPZ Bowl with Cistern for Coupled WC with PP Soft Close Seat Cover, Hinges, Dual Flush Cistern Fitting, Fixing Accessories and Accessories Set, Size: 375x650x790 mm, P Trap-180 mm complete in all respect, with integral 'p' trap including jointing the trap with soil pipe in cement mortar 1:1 ( one cement, one sand) (with cistern, seat cover and flush fitting) Star White complete including carriage of materials in all leads and lift as per direction of Engineer in Charge..( snow white) |
| 120 | Providing and fixing wash basin with built in counter Jaquar FNS-WHT-40801 Half pedestal basin Wall Hung Basin with Fixing Accessories Size: 620x480x185 mmFNS-WHT-40305 Half pedestal with Fixing Accessories for FNS-WHT-40801 Set (MRP) or equivalent series of Hindware /Jaquar complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 121 | Providing and fixing white vitreous china Flat back urinal Jaquar URS-WHT-13253NUrinal (Back Inlet) with Fixing Accessories, Size: 385x325x635 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required : Single half stall urinal with 5 litre P.V.C. automatic flushing cistern complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 122 | Providing and fixing Jaquar SNR-51085K Exposed Part Kit of Urinal Sensor Consisting of Wall Flange with Sensor Eye & (4 X 1.5V AA) Batteries complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 123 | Specifications: Curved shaped urinal partition with frosted glass Glass: 8mm / 10mm Finish: JSE-CHR-110UC450X H: 900 W: 45Chrom BSP thread and shapes, weighing not less than 60 gms.complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 124 | Providing and fixing steel sink of Cera REMY Handmade single bowl sink 304 grade stainless steel Size: 510 x 430 mm (20\\" x 17\\") Bowl Size: 460 x 380 mm (18\\" x 15\\") Depth: 230 mm (9”) Installation: Undermount Cat. No. B4711504 Satin finish Installation: Over-mountequivalent Nirali/ Diamond make of approved design size: a) complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 125 | Providing and fixing Jaquar QUEEN’S QQP-7307PM Sink Mixer with Short Swinging Spout (Wall Mounted Model) with Connecting Legs & Wall Flanges PRIME or equivalent series of Jaquar/ make with 450mm braided connection pipe complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 126 | Providind and fixing Jaquar SNR-15019PMEB Opal Prime Sensor Faucet for Wash Basin (9V transformer) Faucet for Wash Basin Tap (Battery Operated) for table top wash basins with tap hole make with aerator complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 127 | Providing and fixing Jaquar ORP-10037PM Bib Cock with Wall Flange with wall flange and aerator complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 128 | Providing and fixing C.P. brass chain and rubber plug complete for sink or wash basin:complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. 32 mm dia |
| 129 | Providing and fixing bottel trap Jaquar ALD-769L300x190 Bottle Trap 32mm Size with 300mm & 190mm Long Wall Connection Pipes & Wall Flange or equivalent or equivalent series of Cera /Jaquar including carriage of material upto all leads and lifts and as per the direction of Engineer -in-charge |
| 130 | Providing and fixing CP brass waste coupling Jaquar ALD-729 Click Clack Waste 32mm Size Half Thread With 80 mm Height for wash basin or sink Cera make or equivalent series of Cera /Jaquar 32 mm dia with half thread 32mm complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 131 | Providing and fixing P.V.C. waste pipe CERA Outlet connection pipe for single bowl sink without overflow B4811503 of approved make for wash basin and sink complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 132 | Providing & Fixing in position Jaquar ALD-573 Hand Shower (Health Faucet) with 8mm Dia, 1 Meter Long Flexible Tube & Wall Hook Also available or equivelent make complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 133 | Providing and fixing C.P.Brass Jaquar CPA-1111L450 Single Towel Rail 450mm Long or equivalent series of Cera /Jaquar complete with C.P. Brass brackets fixed to wooden plugs with C.P. Brass (600mmx20mm). including carriage of material up to all leads and lifts and as per direction of Engineer incharge. |
| 134 | Providing and fixing C.P.Brass Jaquar CPA-1121RD Towel Ring Round with Round Flange or equivalent series of Cera /Jaquar complete with C.P. Brass brackets fixed to wooden plugs with C.P. Brass (600mmx20mm). complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 135 | Providing and fixing CP brass liquid soap dispenser Jaquar ACN 1135N Soap Dispenser with Glass Bottle r make or or equivalent series of Cera /Jaquar with CP brass brackets fixed to wooden cleats with CP brass screws including carriage of material up to all leads and lifts and as per direction of Engineer incharge. |
| 136 | Providing and fixing CERA SHELF MIRROR 800 x 600 mm 5 mm thick glass mirror with double coat for protection and longevity, 5mm clear glass shelf with stainless steel rail and silver plating on the back for better reflection Cat. No. B3510149 of superior glass mounted on 6mm thick A.C. sheet or ply wood sheet and fixed to wooden plugs with C.P. brass screws and washer including carriage of materials within all leads and lifts :- |
| 137 | Providing and fixing Corner Glass shelves Jaquar ACN-1173 Corner Glass Shelf (with Bracket) Cera /Jaquar complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 138 | Providing and fixing CP brass soap dish make Jaquar AQN-7733 Soap Dish (Polycarbonate) equivalent series of Cera /Jaquar with CP brass brackets fixed to wooden cleats with CP brass screws complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 139 | Providing and fixing C.P. Paper Holder Jaquar CPA-1151 Toilet Roll Holder or equivalent series of Jaquar/ Cera make complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 140 | Providing and fixing Stainless Steel Jaquar WAC-SAP-BR0600CSN Grab Bar 692 mm Long or equivalent series of Jaquar/ Cera make 350mm long complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 141 | Providing and fixing Jaquar WAC-SAP-BG0800CSN U shape Grab Bar Vertical Swing or equivalent series of Jaquar/ Cera make 350mm long complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 142 | Providing and fixing Jaquar FUS-29083K Exposed Part Kit of Concealed Stop Cock & Flush Cock with Fitting Sleeve, Operating Lever & Adjustable Wall Flange with Seal (compatible with ALD-083, ALD-089 or ALD-081) Make or equivalent series of Jaquar/ Cera make with flange including carriage of material to all leads and lifts and as per direction of Engineer incharge. |
| 143 | Providing and fixing P.V.C connection Jaquar ALD-805B 450mm Long Braided Hose with Two 15mm Nuts & Rubber Washers Without Nipple (Suitable for Geysers) length with brass unions 300/450mm length complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 144 | Providing and fixing 100mm dia C.P. Grating including carriage of material up to all leads and lifts and as per direction of Engineer incharge. |
| 145 | Providing and fixing G.I. Union (ISI Mark)complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. i) 15 mm dia |
| 146 | 20 mm dia complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 147 | 25 mm dia complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 21, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 28, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 1 dayJul 28, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 1 dayTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender