Tender For Renovation Of Damaged Drill Shed Size(90X30) At 7Th Bn Tsr, Hqr. Sangkumabari, J Uijala, Sepahijala, Tripura
Tender Value
Ref. Documents
Estimated cost
Bid Submission
10 Aug 2026
16 days left
EMD
28499
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Sepahijala → Tripura
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Renovation Of Damaged Drill Shed Size(90X30) At 7Th Bn Tsr, Hqr. Sangkumabari, J Uijala, Sepahijala, Tripura
BOQ
| Sl. No. | Item Description |
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m widh or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. all kinds of soil. |
| 2 | Supplying and filling in plinth, under floor, foundations etc. with sand (fine) from local quarry with all lifts including spreading in horizontal layers, watering, grading to required slop, ramming, consolidating and compacting each layer by using plate compactor or by any suitable method complete. |
| 3 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering. All work upto plinth level: (i) 1:3:6 ( 1 Cement: 3 fine sand: 6 graded well burnt brick aggregate 40 mm nominal size). |
| 4 | (ii) 1:1 1/2 : 3 ( 1 Cement: 1 1/2 fine sand : 3 graded well burnt brick aggregate 20 mm nominal size) |
| 5 | Centering shuttering including strutting, propping etc. and removal of form work for : (i) Columns, Pillars, Piers, Abutments, Posts and Struts with wooden plank. |
| 6 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. (i) Hot finished welded type tubes. |
| 7 | Dismantling old plaster or pointing, raking out joints, cleaning and preparing the surface for re-plastering or re-pointing including disposal of rubbish to the dumping ground with all leads and lifts etc. competed as per direction of the Engineer-in-charge. |
| 8 | 12 mm cement plaster of mix in/c. neat cement punning (i) Cement mortar 1:4 (1 Cement : 4 fine sand) |
| 9 | Supply & installation of pre-painted Galvalume sheets for roofing/cladding (size, shape and pitch of corrugation as approved by Engineer-in-charge) in 550mpa steel grade, made out of Cold Rolled Steel coated with Zinc-Aluminium alloy coating of 43.5%Zn, 55%Al and 1.5% Silicon confirming to ASTM A792/A792M and AS1397, Alloy coating AZ150/AZ70, colour coated with high quality Polyester coating, top coated of modified polyester of 20 micron, back side coat of 5 micron, having epoxy primer coat of 5 micron on both side. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/ self tapping screws of size (5.5 x 55mm) with EPDM washers filled with white lead complete upto any pitch in horizontal/ vertical or curved surfaces excluding the cost of purlins, rafters and trusses and including cutting of size and shape wherever required and as per direction of Engineer-in-charge. (i) 0.50mm thickness. |
| 10 | Supply & installation of pre-painted Galvalume sheets roofing accessories in 550mpa steel grade, made out of Cold rolled steel coated with Zine Aluminium alloy coating of 43.5% Zn, 55% Al and 1.5% Silicon confirming to AASTM A792/A792M and AS1397, Alloy coating AZ150/AZ70, colour coated with high quality polyester coating, top coated of modified polyester of 20 micron, back side coat of 5 micron, having epoxy primer coat of 5 micron on both side etc. complete as per direction of Engineer-in-charge. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation, Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation. The sheet shall be fixed using self drilling/ self tapping screws with EPDM washers complete for Ridges/Valley/Gutter/Flashing of width 610mm : (a) 0.40mm thickness. |
| 11 | Providing and fixing PVC false ceiling providing SPUF 142-D-01 (Different design 10 mm thick 150mm width and necessary length) approved colour concealed type paneled carrier T section (EWUF 106:40X63.5 mm and L section EWUF 405:40X68 mm) with necessary screws, hold fast, wooden beading and M.S pipe structured 48 mm dia @ 1200 mm c/c including cutting holes and making good walls etc. complete as per direction of Engineer-in-charge. |
| 12 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade [Payment shall be made after submission of Test Certificate issued by the Manufacture]: Two or more coats on new work. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 20, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 10, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 16 daysAug 10, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 16 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender