Tender For Providing Of Hard Standing Pathway With Inter Locking Tiles At Kiari And Special Repair To Bldg No. T-212, T-220, T-221, T-793, P-21, P-61 And Bldg No. T-280 At Karu Under Ge 860 Ews
Tender Value
48.38 Lakhs
Estimated cost
Bid Submission
10 Aug 2026
10 days left
EMD
97000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
leh → Ladakh
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Providing Of Hard Standing Pathway With Inter Locking Tiles At Kiari And Special Repair To Bldg No. T-212, T-220, T-221, T-793, P-21, P-61 And Bldg No. T-280 At Karu Under Ge 860 Ews
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling of wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards/slabs blankets any thickness, including cover fillets complete all as specified and directed by Engr-in Charge |
| 2 | M&L 9 mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with nails to timber frame work in walls complete all as specified and as directed by E-in charge . |
| 3 | M&L 9 mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with nails to timber frame work in Ceiling complete all as specified and as directed by E-in charge . |
| 4 | S&F grid false ceiling GI system powder coated prelude (main runner section 32x24x0.30x3600mm, cross tee 25x24x0.30x1200mm, wall angle 24x24x0.40x3000mm and including providing and fixing PVC pre-laminated in frontside and aluminium foil backed gypsum tile board of size 595 x 595 x 8-9mm fixed in ceiling frame work with necessary fastening GI wire and cleats complete all as specified and directed by Engr-in-Charge. |
| 5 | Dismantling of timber fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section frame workcomplete all as specified and as directed by E-in charge . |
| 6 | M&L second class hard wood timber scantling plain fillets square, rectangular or triangular in section, clean sawn, secured with nails or brads, sectional area exc. 13 Sq cm n.exc 25 Sq cm secured with nails or brads.complete all as specified and as directed by E-in charge . |
| 7 | M&L second class hard wood timber scantling bullnosed, splayed,chamfered or rounded on one edge or face, secured with nails or brads, sectional area exc. 3 Sq cm n.exc 6 Sq cm secured with nails or brads.complete all as specified and as directed by E-in charge . |
| 8 | S&F in repair for SDC Laminated flooring 8mm thick of any coloured, manufactured by Direct Pressure Laminated (DPL) wherein the empty Abrasive aluminium oxide overlay alongwith metamine impregnated decorated film is directly fused with the back with flooring locking profile in designed with double click locking system on the length and single locking width alongwith desire locking strength laid over 1mm thick foam base, complete including removal of existing flooring, all as directed by the Engr-in-Charge. |
| 9 | Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof covering or wall etc complete all as specified and directed by Engr-in-Charge. |
| 10 | M&L for Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet .50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and directed by Engr-in-Charge. |
| 11 | M&L for Pre- painted galvatume aluminum zinc coating GI based plain steel sheet .50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and directed by Engr-in-Charge. |
| 12 | Dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing) removing dismantled tile and rubbish off the premises complete all as specified and directed by Engr-in-Charge. |
| 13 | M&L Non - skid Ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with 15 mm CM 1:4 sceed bed complete all as specified and directed by Engr-in-Charge. |
| 14 | M&L for coloured Glazed ceramic tiles in vertical surface 450 x300 mm with 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including 10 mm thick backing finished even and rough to receive tiles in CM 1:3 complete all as specified and directed by Engr-in-Charge. Make : Somany |
| 15 | Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, laid 1:4 CM in floors etc. 15 mm set and jointed in neat cement slurry and pointed in white or coloured cement to match |
| 16 | Taking down chowkhats or frame exc 1.50 sqm each but n exc 4 sqm each with shutters (without taking off shutters from the frame) complete all as specified and directed by Engr-in Charge |
| 17 | Taking down chowkats or frame not exc 1.5 sqm each with shutters without taking off shutters from the frames complete all as specified and as directed by Engr-in-Charge |
| 18 | S&F poweder coated aluminium windows with sliding shutters and frame made with aluminium section with and including glass/particle board 12mm thick (as specified below) Aluminium sections shall be of size as given below:- Frame : 44.5x44.5x1.60mm thick Top/bottom rail; 90x44.5mmx1.60mm thick side style/rails of shutter-44.5x44.5mmx1.60mm thick Glass : 5mm thick plain glass with rubber gasket with aluminium beading . Aluminium fitting such as peg stay, aluminium hinges, aluminium handle 100mm long, aluminium tower bolt 100mm long and making good of wall surface with matching to existing surface, complete all as specified and as directed by Engr-in-Charge. |
| 19 | S&F poweder coated aluminium glazed door complete with shutter size of style top rail and lock rail 83x45x1.60mm thick and bottom rail 114x44x1.60mm thick and door frame size 63x38x1.60 mm including aluminium mongry fitting, hinges, tower bolt, handle, lock etc all necessary fittings and glazing with 5mm thick tinted glass/12mm thick pre laminated particle board complete including rubber lining at sides for air locking with complete all as speicified and as directed by Engr in Charge. |
| 20 | S&F for 2nd Class hard wood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed |
| 21 | S&F plain 2nd class hardwood 35mm thick framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and as directed. |
| 22 | S&F 100mm Butt hinges, medium weight, cold rolled mild steel, and fixed complete all as specified and directed |
| 23 | S&F 150mm Aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed |
| 24 | S&F 150mm Aluminium handles, cast type, anodised complete all as specified and directed |
| 25 | M&L for two coat of synthetic enamel (ordinary tint each coat) over a coat priming with pink primer on new or previously untreated wooden surfacecomplete all as specified and directed by Engr in Charge |
| 26 | S&F aluminum body door closer (extruded section) hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed by Engr-in-Charge. |
| 27 | Hacking out old broken glass (any thickness, size, quality or description) from from metal frame including punching or drilling out old glazing pins/spring clips and providing, complete all as specified and directed by Engr-in-Charge. |
| 28 | S&F of 4mm thick sheet glass, ordinary quality and glazing with oil putty and glazing pins in square n exc 0.5 sqm in each pane complete all as specified and directed by Engr-in-Charge. |
| 29 | S&Fin repair Vitreous China wash basin, white, pedestal type flat back, size 580x450irun include waste pipe, chain and plug and porcelain stopper but including brackets complete all as specified and directed by Engr-in-Charge |
| 30 | S&F in repairs vitreous china water closet (squatt pan) orrisa pattern 580x440 mm size pan white with front or back inlet with integral 'foot rests including provn of lime concrete bedding including connections to 'flushing cistern/pipe including 100mm PVC 'P' trap complete all as specified and directed by Engr-in-Charge |
| 31 | S&F in repair vitreous China wash down (EWC) water closet pan (pedestal pattern), white (excluding flushing cistern and flush pipe) including seat cover for pedestal pattern complete all as specified and directed by Engr-in-Charge. (Make : Jaquar/Cera) |
| 32 | S&F in repair PVC 10 Ltrs valve less, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete with 32 mm dia flush pipe connecting to squatt pattern etc. ISI approved etc complete all as specified and directed by Engr-in-Charge. |
| 33 | S&F in repairs PVC connections 15mm size with PTMT nuts of length 450 mm complete all as specified and directed by Engr-in-Charge |
| 34 | S&F in repair 15 mm bore bib tap brass chromium plated fancy type with crutch or butterfly handle screwed down, screwed for iron pipe complete all as specified and directed. |
| 35 | S&F in repairs 15mm bore pillar taps CP brass chromium plated fancy type screwed down high pressure with chromium plated screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed. |
| 36 | S&F in repairs 15 mm bore stop valves, cast copper alloy, fancy type, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed. |
| 37 | S&F in repairs 32 mm dia bore waste fittings brass chromium plated fixed to wash hand basin, sinks with long screwed shanks and fly nuts flange and bedded in red lead cement and other end fixed complete all as specified and directed. |
| 38 | Demolition and breaking up drain pipes (salt glazed ware, PVC or re-inforced concrete) set in cement mortar internal dia of pipe 100mm complete all as specified and directed by Engr-in-Charge. |
| 39 | S&F 110mm dia bore PVC (SWR) pipes single socketed in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed by Engr-in-Charge. |
| 40 | M&L PCC 1:3:6 type C-2 as in 110mm bore of pipe in concrete bed to drain pipes including packing under and haunching against the sides of pips after they are laid and tested complete all as specified and directed by Engr-in-Charge. |
| 41 | Taking up or down 20 mm dia steel tubing and connections, complete all as specified and as directed by the Engr-in-Charge |
| 42 | Taking up or down 25 mm dia steel tubing and connections,complete all as specified and as directed by the Engr-in-Charge |
| 43 | S&F 3 layer PP-R Polypropyene ransom copolymer outer dia of pipe 20 mm pipes SDR 7.4 (PN-16) UV stablized and anti microbial fusionwelded having thermal stavility for hot & cold water supply including all PPR plain & brass threaded polypropylene random fittings fixed complete to walls, celling or in floors etc complete all as specified and directed by the Engineer -in-Charge |
| 44 | S&F 3 layer PP-R Polypropyene ransom copolymer outer dia of pipe 25 mm pipes SDR 7.4 (PN-16) UV stablized and anti microbial fusionwelded having thermal stavility for hot & cold water supply including all PPR plain & brass threaded polypropylene random fittings fixed complete to walls, celling or in floors etc complete all as specified and directed by the Engineer -in-Charge |
| 45 | S&F floor trap of PVC 75 mm out let dia with grating and jointed to waste pipe as spfd.complete all as specified and directed by engr-in-charge |
| 46 | M&L for PVC (SWR) 110 mm gully trap setting joining with solvent cement complete all as specified and directed. |
| 47 | Dismantling water tanks exc 500 Ltr & n exc 1000 Ltr complete all as specified and directed by Engr in Charge |
| 48 | S&F rotantional moulded polythylene water storage tanks 750 ltr capacity (cylindrical vertical with closed top ) hoisted and fixed in posplinition complete with ball valve of high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball and screwd for iron pipe 20mm bore omplete all as specified and directed. |
| 49 | S&F in repair 25 mm bore Gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed.complete all as specified and directed by engr-in-charge. |
| 50 | Demolition of Brickwork / concrete block or stone/ boulder masonry, built in cement mortar complete all as specified and directed by Engr-in-Charge. |
| 51 | M&L Pre-cast cement concrete block masonry with solid blocks, exc. 10 cm in width and setting in mortar, complete type C1 1:3:6 (20 mm graded agg) set in CM 1:4 completed all as specified and directed by Engr-in-charge . |
| 52 | M&L Rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 is to be finished even and smooth with out using extra cement complete all as specified and directed by Engr-in-Charge. |
| 53 | Taking down cement plaster on brick or stone etc including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed by Engr-in-Charge. |
| 54 | M&L Rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 is to be finished even and smooth with out using extra cement complete all as specified and directed by Engr-in-Charge. |
| 55 | M&L for preparing new surfaces of plastered or unplastered and applying two coat of cement base paint over chalk whiting complete all as specified and directed by Engr-in-Charge. (Note : Ladders, scaffolding will be provided by Contractor where required) |
| 56 | M&L for preparing new surfaces of plastered or unplastered and applying three coat of white wash complete all as specified and directed by Engr-in-Charge. (Note : Ladders, scaffolding will be provided by Contractor where required) |
| 57 | M&L for preparation of new or previously untreated wooden surfaces of any description not otherwise described over 10cm in width or girth and applying two coats of synthetic enamel paint (1st grade quality) over a coat of pink primer complete all as specified and directed by Engr-in-Charge. |
| 58 | Demolition of cement concrete (Unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed by Engr-in-Charge. |
| 59 | M&L for 75 mm thick Cement concrete type C-2, 1:3:6 (20mm graded crushed stone aggregate) as in floor plinth protection, finishing cement concrete surface even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge. |
| 60 | S&F M&L for readymade soft wood wall /Ceiling panelling in strips of 100 mm width 10mm thickness having lounge and groove fixing arrangements fixed to wooden frame work(Size of frame work 1.2X1.2 C/C included ) as per manufacturers instruction including polishing complete all as specified and as directed by Engr-in- Charge .Note : if necassary size of the frame work/ wall paneling will be changed as per site requirement without any cost different complete all as specified and directed by Engr-in-Charge. |
| 61 | S&F for 30mm thick 2nd class hardwood Plain, framed, panelled door shutters(any number of panels), with panels of timber flat on both sides(feather edged), veneered particle board medium density, wood particle board with commercial face veneers, supplied and fitted to chowkats complete all as specified and directed by Engr-in-Charge. |
| 62 | S&F 200 mm long Aluminium, anodised, barrel tower bolt, fixed with screws complete all as specified and directed by Engr-in-Charge. |
| 63 | S&F 150 mm size, Aluminium anodised handles fabricated type polished complete all as specified and directed by Engr-in-Charge. |
| 64 | S&F of 250 mm long, aluminium alloy,anodised,sliding door bolts, with hasp, staple ( bolt type) and fixing clip of sheet, cast or extruded section and fixing bolt and sliding bolts of extruded section section or cast aluminium alloy complete all as specified and directed by Engr-in-Charge. |
| 65 | S&F in repair sinks made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.complete all as specified and directed by Engr-in-Charge. |
| 66 | Demolition Stone slabs and tiles Laid beded and pointed cement mortar of any description or thickness in floors, aprons etc. all as specified and directed by Engr-in Charge. |
| 67 | M&L Granite 25 mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and Providing edge moulding to 18-20mm thick granite stone of counters vanities etc. including machine polishing to edge to give high gloss finish etc. complete all as specified and directed by Engr-in-Charge. |
| 68 | M&L Providing edge moulding to 18-20mm thick granite stone of counters vanities etc. including machine polishing to edge to give high gloss finish etc. complete all as specified and directed by Engr-in-Charge. |
| 69 | M&L for preparation/removal of old painted steel surfaces and applying two coat of synthetic enamel paint on surface of any description over 10cm width or girth complete all as specified and directed by Engr-in-Charge. |
| 70 | S&F 110mm dia bore PVC (SWR) bends complete all as specified and directed.complete all as specified and directed by Engr-in-Charge. |
| 71 | Surface dressing n.exc 15cm deep in soft/loose soil. |
| 72 | M&L for Hardcor of guage n exc 63mm, deposited, spread and levelled in layers n exc. 15cm thick, watered and rammed to a true surface complete all as specified and directed. |
| 73 | M&L for cement concrete 1:3:6 100mm thick type C-2 using 40mm graded stone aggregate over rammed earth as in sub base to receive floor finish etc complete all as specified. |
| 74 | Providing and laying 80mm thick factory made chamferred edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine said and cutting of paver block as per required size and pattern, finishing and sweeping extra sand complete. |
| 75 | M&L for Providing, cement concrete in roof kerbs or mud stops, rounded or chamfered on edges type B1 1:2:4 (20mm graded aggregate). |
| 76 | Taking down carefully alluminium / copper point wiring complete for light, fan, socket or power point etc with fittings fixtures such as ceiling rose, holders, electric fittings, switchs, sockets, aluminium conductor cable with and incl wooden batten or FR PVC conduit and its accessories such as wooden gutties, rawl plugs, GI screws, aluminium clips, nails etc complete and removing the material from site and making good the disturbed surface of wall / floor/ ceiling etc as original i.e. brick work, plastering, white washing, OBD etc as required, complete all as specified and directed. |
| 77 | M&L point wiring complete with single core FRLS PVC insulated, unsheathed, multi stranded copper conductor cables 1.5 Sqmm 1100 volts grade, with and incl 1.5 Sqmm FRLS PVC insulated, unsheathed, multi stranded copper conductor cables as continuous earth wire connected to metallic bodies of luminaries / fans etc at one end and to common earth dolly at other end, complete wiring drawn through & PVC casing and capping of 25 mm and above (as per conductor run ) medium grade, ISI marked, incl all accessories & fittings / junction boxes / inspection covers etc, with and incl surface PVC Boxes of suitable size fixes with wall surface, Gang box for top cover suitable for fixing of piano type switches / sockets etc, complete all as specified and directed |
| 78 | Description all as per item No. 77.00 here-in-before but with One light / bell / buzzer / exhaust fan point controlled by one no, 1-way, 5 Amps switch. |
| 79 | Description all as per item No. 77.00 here-in-before but with One socket outlet 3 pin, 5 Amps on independent board, controlled by one no 5 Amp switch. |
| 80 | Description all as per item No. 77.00 here-in-before but with 2.5 sq mm FRLS copper wire with 1.5 Sqmm FRLS copper earth wire for indpendent 15 Amp point. |
| 81 | S&F in repalcement, of Switch piano type, single pole, one way, 5 amps, 230 volts, complete all as specified and directed. |
| 82 | S&F in repalcement, of Switch Socket combination, two-in-one, 5 pin, 5 Amp, universal type, 230 volts, complete all as specified and directed. |
| 83 | S&F in repalcement, of Switch Socket combination, 6 pin, 5/15 Amp, multipurpose shutter type, 230 volts, complete all as specified and directed. |
| 84 | S&F in repalcement, of Ceiling rose, two to three terminals, bakelite body, 230 volts, complete all as specified and directed. |
| 85 | Supply and fixing LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete. |
| 86 | S&F in replacement LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal anagement in multiple optics complete with IP 65/66 protection complete all as directed by Engr-in-Charge at site including necessary fixing arrangement like bracket, clamps and nuts and bolts. |
| 87 | S&F in replacement Lamps Holder PVC/ polycabonate by with back plate angular type |
| 88 | S&F LED bulb 9W for fixing with lamp holder |
| 89 | S&F in replacement exhaust fans made of sturdy Engineering plastic AC single phase 230/ 240 V of size 250 mm sweep with louvre complete in cluding making hole in the wall and making good the disturbed surfaces complete all as directed by EIC at site |
| 90 | S&F in replacement of DB, Single Door, made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, SPN 4 way, 240 volts with bus bar rating 200 Amps, dust and vermin proof, suitable for incorporation of MCB’s and isolators etc and making all necessary connections, duly flush of wall surface, complete all as specified and directed. |
| 91 | S&F in replacement of MCB, C Curve type, 10 kA, 40 to 63 Amp, SPN with over load and short circuit protection, complete all as directed. Make : Schneider Elect / Legrand / C&S / Hager |
| 92 | S&F in replacement of MCB, C Curve type, 10 kA, 6 to 32 Amp, Single Pole with over load and short circuit protection, complete all as directed. |
| 93 | Supply and laying XLPE insulated, armoured, heavy duty electric cable, with stranded aluminum conductor 1100 V grade nominal cross sectional area 10 Sqmm, 2 core laid in trenches, ducts, drawn through pipes across the road/path/along poles/wall/floors/equipment etc including jointing and testing complete all as specified and directed by the Engr-in-Charge |
| 94 | Excavation in trenches not exceeding 1.5m and not exceeding 1.5m in depth for laying of electric cable and getting out in hard and dense soil, complete all as specified and as directed by the Engr-in-Charge. |
| 95 | Returning, filling in excavated soil, including leveling, watering and well ramming in layers not exceeding 25 cm thick complete all as specified and as directed by the Engr-in-Charge. |
| 96 | Removing excavated material (soil) not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and as directed by the Engr-in-Charge. |
| 97 | Material and labour for un-reinforced pre-cast concrete cable covers, class LV type-1, flat size 250mm x 150mm x 40mm thick complete all as specified. |
| 98 | Material and labour for sand cushioning to under ground electric cable all as per clause No 19.75 of MES SSR Part-I (1991) |
| 99 | M&L for earthing with galvanized steel earth plate electrode of size 600 x 600 x 6 mm buried directly in ground earth pit not less than 2.25 mtr below of normal ground level with top edge of earth plate should not less than 1.5 mtr below normal ground level and connected to galvanized iron earth lead wire of size 4 mm dia by means of bolts, nuts, washers of galvanized iron or steel all as shown in electrical plate No.3 of MES SSR Part I connecting to earthing test point on completion with and including 15 mm bore GI light grade protection pipe (7.5 mtr long) for earth lead GI lead wire 4mm dia (7.5 mtr long), PCC pit with cover in PCC 1:2:4 type B-1 reinforced with 8 mm dia tor bars @ 80mm C/C, 20mm dia medium grade watering pipe with funnel, wire mesh, common salt, charcoal, necessary excavation and earth work, complete all as specified and directed. Please Enable Macros to View BoQ information |
| 100 | M&L for earthing with galvanized steel earth plate electrode of size 600 x 600 x 6 mm buried directly in ground earth pit not less than 2.25 mtr below of normal ground level with top edge of earth plate should not less than 1.5 mtr below normal ground level and connected to galvanized iron earth lead wire of size 4 mm dia by means of bolts, nuts, washers of galvanized iron or steel all as shown in electrical plate No.3 of MES SSR Part I connecting to earthing test point on completion with and including 15 mm bore GI light grade protection pipe (7.5 mtr long) for earth lead GI lead wire 4mm dia (7.5 mtr long), PCC pit with cover in PCC 1:2:4 type B-1 reinforced with 8 mm dia tor bars @ 80mm C/C, 20mm dia medium grade watering pipe with funnel, wire mesh, common salt, charcoal, necessary excavation and earth work, complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 20, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 10, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 10 daysAug 12, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 12 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender