Tender For Hvac System For College Lab Block /Library Block At Skims Mch Bemina.(In Selected Areas)
Tender Value
3.56 Crore
Estimated cost
Bid Submission
10 Aug 2026
18 days left
EMD
Ref. Documents
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Budgam → Jammu and Kashmir
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Hvac System For College Lab Block /Library Block At Skims Mch Bemina.(In Selected Areas)
BOQ
| Sl. No. | Item Description |
| 1 | AIR COOLED SCREW HEAT PUMP (REVERSIBLE TYPE) For Space Cooling and Heating |
| 2 | Supply, Installation, Testing, & Commissioning of AHRI certified Reversible Air Cooled Screw Heat Pump having Single/Multiple twin rotor screw compressors not less than 321kW actual capacity for heating and not less than 130 TR actual capacity for cooling at the parameter mentioned below.Rest of the specifications as per Annexure B of the E-NIT |
| 3 | Water Pumps Set Set with VFD & Microprocessor Panel, sensor, transformer, controller, star Delta Starters for primary and secondary pumps etc.Supply, installation, testing and commissioning of End Suction Back pull out centrifugal pumps complete with motor, base frame, vibration isolators, drain valves and other accessories. Specifications as per Annexure B of the E-NIT. |
| 4 | Chilled Water Primary Pumps Set (2w + 1S) (with VFD & Microprocessor Panel, sensor, transformer, controller, star Delta Starters for primary and secondary pumps etc.) for Space heating / coolingWater flow rate : 240-340 USGPM for Space heating / coolingHead : 40 ftRPM : 1450 |
| 5 | Secondary Hot water pumps (with VFD & Microprocessor Panel, sensor, transformer, controller, star Delta Starters for primary and secondary pumps etc.) for Space heating / cooling ( (2w + 1S) Water flow rate :240-340 USGPM for Space coolingHead : 115ftRPMP :1450 |
| 6 | CHILLED WATER PIPES AND VALVES |
| 7 | Supplying, laying/ fixing, testing and commissioning of following nominal sizes of Hot / chilled water piping plumbing inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with fire retardant quality expanded polystrene moulded pipe section of density 20 kg/cu.m after a thick coat of cold setting adhesive (CPRX compound) wrapping with 500g polythene faced hessain and finally applying 0.63mm aluminium sheet cladding complete with type3 , grade 1 roofing felts trip(as per IS:1322 as amended up to date ) at joints repairing of damage to building etc. as per specifications and as required complete in all respect.Specifications as per Annexure B of the e-NIT. |
| 8 | 150mm dia (75mm insulation) |
| 9 | 125mm dia.(50 mm insulation) |
| 10 | INUSLATED VALVE |
| 11 | Supplying, fixing, testing and commissioning of following valves, strainers, gauges in the chilled water plumbing duly insulated to the same specifications as the connected piping and adequately supported as perspecifications |
| 12 | BUTTERFLY VALVE (MANUAL) with C I body SS Disc, Nitrile Rubber Seal & O- Ring PN 16 pressure rating forchilled water/hot water circulation as specified |
| 13 | 150 mm dia |
| 14 | 125 mm dia |
| 15 | BALANCING VALVE WITH BUILT IN MEASURING FACILITY with C I body flanged construction with EPDM coated disc with long pitch with protected out pipe insulation & PN 16 pressure rating for chilled / hot water circulation as specified. |
| 16 | 125 mm dia |
| 17 | NON - RETURN VALVE with dual plate of C I body SS plates vulcanized NBR seal flanged end & PN 16 pressurerating for chilled / hot water circulation including insulation as specified. |
| 18 | 125 mm dia |
| 19 | Y - STRAINER of Ductile CI Body flanged ends with stainless steel strainer for chilled / hot water circulationincluding insulation as specified. |
| 20 | 125 mm dia |
| 21 | Providing & Fixing in position the industrial type pressure guages with gun metal/brass valves compelete asrequired |
| 22 | Providing & Fixing in position the mercury in glass with industrial type thermometers. |
| 23 | Providing and fixing in position the following Flexible coupling (with conrtol rods) for the chilled/Hot waterpumps. |
| 24 | 125 mm dia |
| 25 | Providing and fixing in position the following water flow switch as per specifications: |
| 26 | 32 mm dia |
| 27 | Providing and fixing in position the following Drain Valves (For Drain) duly insulated as per specifications anddrawings |
| 28 | 25 mm dia |
| 29 | Expansion Tank |
| 30 | Providing, Supplying, Installing, Testing and Commissioning of Automatic Pressure Maintenance (Pressurization) Unit complete with Pressurized Expansion Tank for closed loop HVAC Chilled water/Heating Water system, including pumps, control panel, expansion vessel, piping, valves, insrumentation, accessories and all associated works complete in all respects. Rest of the specifications as per Annexure B of the e-NIT |
| 31 | Supply ,Installation, Testing and Commissioning of Raw Water Feed Pump complete with electric motor of requisit capacity with inlet and outlet valves installed on suitable base frame . Having Head 25 m or above and Discharge 400 LPM ( Mim) , 1450/2900 rpm |
| 32 | Supplying, laying/ fixing, testing and commissioning of following nominal sizes of Hot / chilled water piping plumbing inside the building. Rest of the specifications as per Annexure B of the e-NIT |
| 33 | 125mm dia.(50mm insulation) |
| 34 | 100mm dia.(50mm insulation) |
| 35 | 80mm dia.(50mm insulation) |
| 36 | 65mm dia.(50mm insulation) |
| 37 | 50mm dia.(50mm insulation) |
| 38 | 40mm dia.(50mm insulation) |
| 39 | 32mm dia.(50mm insulation) |
| 40 | 25mm dia.(50mm insulation) |
| 41 | INUSLATED VALVE |
| 42 | Supplying, fixing, testing and commissioning of following valves, strainers, gauges in the chilled water plumbing duly insulated to the same specifications as the connected piping and adequately supported as perspecifications |
| 43 | BUTTERFLY VALVE (MANUAL) with C I body SS Disc, Nitrile Rubber Seal & O- Ring PN 16 pressure rating forchilled water/hot water circulation as specified |
| 44 | 100 mm dia |
| 45 | 80 mm dia |
| 46 | 65 mm dia |
| 47 | 50 mm dia |
| 48 | Y - STRAINER of Ductile CI Body flanged ends with stainless steel strainer for chilled / hot water circulationincluding insulation as specified. |
| 49 | 50 mm dia |
| 50 | 40 mm dia |
| 51 | Providing & Fixing in position the industrial type pressure guages with gun metal/brass valves compelete asrequired |
| 52 | Providing & Fixing in position the mercury in glass with industrial type thermometers. |
| 53 | AIR DISTRIBUTION DUCT ( FOR VENETILATION)Supplying, installation, balancing and commissioning of fabricated at site GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers,supports, bends, transitions, reducers, end caps, collars etc as required complete in all respect inconfirmation with IS : 655 and approved drawings and specifications of following sheet thickness complete as required. |
| 54 | Thickness 0.63 mm sheet |
| 55 | Thickness 0.80 mm sheet |
| 56 | AIR DISTRIBUTION DUCT ( FOR AIRCONDITIONING)Supplying, installation, balancing and commissioning of fabricated at site GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers,supports, bends, transitions, reducers, end caps, collars etc as required complete in all respect inconfirmation with IS : 655 and approved drawings and specifications of following sheet thickness complete as required. |
| 57 | Thickness 0.63 mm sheet |
| 58 | Thickness 0.80 mm sheet |
| 59 | Supplying and fixing of 19 mm thick duly laminated aluminium foil of mat finish closed cell nitrile rubber (Class O) insulation on existing duct after applying suitable adhesive for nitrile rubber. The joints shall be sealed with 50 mm wide and 3 mm thick self adhesive nitrile rubber tape insulation. Complete as per specs and as required |
| 60 | Supplying, installation, testing and commissioning of GI volume control duct damper complete with neoprene rubber gaskets, nuts, bolts, screws linkages, flanges etc in confirmation to SMACNA/IS and as per specifications complete etc. as required. |
| 61 | SUPPLY / RETURN AIR DIFFUSERS |
| 62 | Supplying, Fixing, installation, testing and commissioning of supply air diffusers of powder coated aluminium with aluminium volume control dampers with anti smudge ring & removable core in confirmation to SMACNA/IS and as per specifications complete etc. as required. |
| 63 | Supplying, Fixing, installation, testing and commissioning of Return air diffusers of powder coated aluminium without volume control dampers with anti smudge ring & removable core inconfirmation to SMACNA/IS and as per specifications complete etc. as required. |
| 64 | SUPPLY / RETURN AIR GRILLES |
| 65 | Supplying, Fixing, installation, testing and commissioning of powder coated extruded aluminium Supply Air Grills with aluminium volume control dampers in confirmation to SMACNA/IS and as per specifications complete etc. as required. |
| 66 | Supplying & fixing of powder coated extruded aluminium Return Air Grills with louvers but without volume control dampers complete in confirmation to SMACNA/IS and as per specifications complete etc. as required. |
| 67 | FIRE DAMPERS |
| 68 | Supplying, Fixing, testing and commissioning of fire dampers of minimum 90 minutes fire rated in supply air duct/main branch and return air path as and where required of required sizes i/c control wiring, the damper shall be motorized and spring return so as to close the damper in the event of power failure automatically and open the same in case of power being restored. The spring return action shall be inbuilt mechanism and not externally mounted. The damper shall also be closed in the event of fire signal and, inconfirmation to IS and as per specifications complete etc. as required.. |
| 69 | Fire damper |
| 70 | Actuator |
| 71 | Air Handling Units |
| 72 | Supplying, Installation, Testing and commissioning of factory built ceiling mounted chilled/hot water double skin type horizontal air handling units made of 25mm thick panels consisting of pre plasticized G.I. casing of thickness 0.8mm outside layer and 0.8 mm inside layer with polyurethane foam (PUF) insulation factory injected between them by injection moulding machine, complete with blower section with blower suitable for static pressure as required, minimum 2 bend GSS/PVC eliminators, cooling/heating coil section with aluminium finned copper tubes (tubes thickness not less than 0.4mm) cooling/heating coil of 4 row deep, filter section with 50mm thick metal viscous/ washable synthetic type air prefilters, rest as per Annexure B of the e-NIT |
| 73 | 6000 CFM (CS) AHU, 30 KW heating capacity, 4 row deep heating/Cooling coil, 50 mm Static Pressure with 3 Phase motor(VFD Driven) as per OEM recommendation with requsite control panel consisting of mammul and auto on/off selector switch with requisite capacity of MCCBS phase sequencer, single phase preventer , digital Amp meter and indiction on/off lamps. The job also includes the providing and fixing of 4 core 4sqmm cable from Ahu to control panel. |
| 74 | 5500 CFM (CS) AHU, 28 KW heating capacity, 4 row deep heating coil, 50 mm Static Pressure with 3 Phase motor (VFD Driven) as per OEM recommendation with requsite control panel consisting of mammul and auto on/off selector switch with requisite capacity of MCCBS phase sequencer, single phase preventer , digital Amp meter and indiction on/off lamps. The job also includes the providing and fixing of 4 core 4sqmm cable from Ahu to control panel. |
| 75 | 4500 CFM (CS) AHU, 22 KW heating capacity, 4 row deep heating coil, 50 mm Static Pressure with 3 Phase motor (VFD Driven) as per OEM recommendation with requsite control panel consisting of mammul and auto on/off selector switch with requisite capacity of MCCBS phase sequencer, single phase preventer , digital Amp meter and indiction on/off lamps. The job also includes the providing and fixing of 4 core 4sqmm cable from Ahu to control panel. |
| 76 | 4000 CFM (CS) AHU, 20 KW heating capacity, 4 row deep heating coil, 50 mm Static Pressure with 3 Phase motor (VFD Driven) as per OEM recommendation with requsite control panel consisting of mammul and auto on/off selector switch with requisite capacity of MCCBS phase sequencer, single phase preventer , digital Amp meter and indiction on/off lamps. The job also includes the providing and fixing of 4 core 4sqmm cable from Ahu to control panel. |
| 77 | 3500CFM (CS) AHU, 18KW heating capacity, 4 row deep heating coil, 50 mm Static Pressure with 3 Phase motor as per OEM recommendation with requsite control panel consisting of mammul and auto on/off selector switch with requisite capacity of MCCBS phase sequencer, single phase preventer , digital Amp meter and indiction on/off lamps. The job also includes the providing and fixing of 4 core 4sqmm cable from Ahu to control panel. |
| 78 | 2500 CFM (CS) AHU, 15 KW heating capacity, 4 row deep heating coil, 50 mm Static Pressure with 3 Phasemotor (VFD Driven) as per OEM recommendation with requsite control panel consisting of mammul and auto on/off selector switch with requisite capacity of MCCBS phase sequencer, single phase preventer , digital Amp meter and indiction on/off lamps. The job also includes the providing and fixing of 4 core 4sqmm cable from Ahu to control panel. |
| 79 | 2000 CFM (CS) AHU, 9.5 KW heating capacity, 4 row deep heating coil, 50 mm Static Pressure with 3 Phase motor as per OEM recommendation with requsite control panel consisting of mammul and auto on/off selector switch with requisite capacity of MCCBS phase sequencer, single phase preventer , digital Amp meter and indiction on/off lamps. The job also includes the providing and fixing of 4 core 4sqmm cable from Ahu to control panel. |
| 80 | 1800 CFM (CS) AHU, 9 KW heating capacity, 4 row deep heating coil, 50 mm Static Pressure with 3 Phase motor (VFD Driven) as per OEM recommendation with requsite control panel consisting of mammul and auto on/off selector switch with requisite capacity of MCCBS phase sequencer, single phase preventer , digital Amp meter and indiction on/off lamps. The job also includes the providing and fixing of 4 core 4sqmm cable from Ahu to control panel. |
| 81 | Duty : Floor Smoke Extraction (First to Seventh Floor)Air Quantity : 5000 CFM Static Pressure : 20 mm wgMotor rating : as per OEM recommendation |
| 82 | Duty : Make Up Air Supply (First to Seventh Floor)Air Quantity : 4,000 CFMStatic Pressure : 20 mm wgMotor Rating : as per OEM recommendation |
| 83 | INLINE FANSSupply, installation, testing and commissioning of inline ducted Fans as shown in drawings. Fan motor shall be suitable forsingle phase, 50 Hz AC supply. The capacity of the fan given as under:-Air Quantity : 550 CFM Static Pressure : 20 mm wgMotor rating : as per OEM recommendation Location : First to Seventh Floor |
| 84 | Air Quantity : 450 CFMMotor rating : as per OEM recommendationStatic Pressure : 20 mm wg Location : First to Seventh Floor |
| 85 | Air Quantity : 100 CFMStatic Pressure : 5 mm wgMotor rating : as per OEM recommendation Location : First to Sixth Floor |
| 86 | Supply, installation, testing and commissioning of cooling thermostats for various Air Handling Units and Fan Coil Units as per specifications including all accessaries ,mountings,wiring between thermostat & unit, terminations etc. |
| 87 | Proportional thermostats for Air Handling Units |
| 88 | Supply,Installation Testing and Commissioning of PICB Valves with electronic,modulating,2 way control device,adjustableto 51 different setting within the range of valve size. |
| 89 | 32-17 USGPM |
| 90 | 16-09 USGPM |
| 91 | Providing and fixing in position the following Ball Valves with Strainer duly insulated as per specifications and drawings |
| 92 | 40 mm dia |
| 93 | 32 mm dia |
| 94 | 25 mm dia |
| 95 | Providing and fixing in position the following Ball Valves without strainer duly insulated as per specifications and drawings |
| 96 | 40 mm dia |
| 97 | 32 mm dia |
| 98 | 25 mm dia |
| 99 | Providing and fixing in position the following Drain Valves (For Drain) duly insulataed as per specifications and drawings |
| 100 | 40 mm dia |
| 101 | 32 mm dia |
| 102 | Providing and fixing in position the following Purge Valves duly insulataed as per specifications and drawings |
| 103 | 25 mm dia |
| 104 | DRIAN PIPE |
| 105 | Providing and fixing in position the following GI medium class cut to required length and installed with screw joints including the necessary fittings (bends, tees, unions, sockets etc) duly insulated with 25 mm thick TF quality thermocolepipe section as per specifications. |
| 106 | 32 mm dia |
| 107 | 25 mm dia |
| 108 | Supply, installation and balancing of extruded aluminium powder coated air louvers complete with aluminium wire meshbirdscreen & volume conrtol dampers as per specifications. |
| 109 | Fresh air louvers |
| 110 | Exhaust air louvers(without volume control dampers) |
| 111 | Supply and fixing of Acoustic lining with fibre glass wool density shall be 32 Kg/ m3,inside the ducts as per specificationsand as shown on drawings. |
| 112 | 25 mm thick |
| 113 | Providing and lying inposition cement concreate of specified grade including the cost of centring and shuttering - all work up to plinth level. 1:2:4 ( 1 cement: 2 coase sand: 4 gradeed stone aggrigate 20 mm nominal size stone) |
| 114 | Supplying, installation ,testing and commissioning ofHigh wall Fan Coil Unit comprising of two 2 rows deepchilled water cooling coil, centrifugal blowers,fractional horsepower (FHP) motor , synthetic fibrefilters, insulated & extended condensate drain pan,casing, coil piping connections, condensate drainpiping connections & wiring. Fan coil units shall besuitable for operation on 220 + 10% Volts, 50Hz,single phase power supply of following sizes &capacities. As directed by Engineer-in-charge. |
| 115 | 2.0 TR nominal capacity with 800 Cfm air quantity. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 21, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 10, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 18 daysAug 11, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 19 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender