Tender For As & As And Repairs To P-23 Buildings At 7N Det Under Ge Tirunelveli (Tender Id: 2026_Mes_ _1)
Tender Value
1.44 Crore
Estimated cost
Bid Submission
13 Aug 2026
12 days left
EMD
2.19 Lakhs
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
tirunelveli → Tamil Nadu
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For As & As And Repairs To P-23 Buildings At 7N Det Under Ge Tirunelveli (Tender Id: 2026_Mes_ _1)
BOQ
| Sl. No. | Item Description |
| 1 | Sch A Part I (B/R items )Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish removed outside the Defence land complete all as specified. |
| 2 | Material and labour for vitrified ceramic light shade coloured tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match including screed bed or bedding layer of mortar 15 mm thick in CM 1:6 complete all as specified. |
| 3 | All as per item No.2 above but in vertical surfaces and jointed in neat cement slurry and pointed in coloured cement to match including backing coat 10mm thick in CM 1:4 on brick walls for skirting/DADO complete all as specified and as directed. |
| 4 | Material and labour for non - skid Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors set and jointed in neat cement slurry and pointed in coloured cement to match including screed bed or bedding layer of mortar 15 mm thick in CM 1:6 complete all as specified. |
| 5 | Material and labour for 450x350x7mm thick glazed coloured ceramic tiles in vertical surfaces set and jointed in neat cement slurry pointed in coloured cement to match over rendering 10 mm thick on fair faces of brick work in CM (1:4) complete all as specified and directed. |
| 6 | Material and labour for PCC 1:2:4 type B0, 25mm thk using 12.5mm aggregate as in sub base complete all as specified and as directed. |
| 7 | Material and labour for chequered Cement concrete tiles 30cm x 30cm x25mm thick, with grey cement and pigment set, jointed and pointed in neat cement slurry in floors, including Screed bed or bedding layer of mortar 15mm thick in CM (1:6) for laying floor finishes complete all as specified and directed. |
| 8 | Material and labour for Machine cut pre polished kota stone slab flooring 20-25mm thick over cement screed base 15mm thick in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed. |
| 9 | Material and labour for Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed including 10mm thick rendering in CM 1:4 etc complete all as specified and as directed. |
| 10 | Material and labour for 20mm thick Granite (of any type) tiles machine cut, in skirting/dado/vertical surfaces laid over cement screed and jointed with grey cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing laid over and including 10mm thick screed bed or bedding layer of mortar in CM 1:4 complete all as specified and directed. |
| 11 | Cutting chases,not exc 10 cm girth, on brick walls pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; for concealed water tubing and making good, cutting complete all as specified and directed. |
| 12 | Supply and fixing 20mm bore CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including taking down old existing steel tubing and connections of 15mm bore complete all as specified and as directed. |
| 13 | Supply and fixing 25mm bore CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including taking down old existing steel tubing and connections of 20mm bore complete all as specified and as directed. |
| 14 | Supply and fixing in repair vitreous China wash down water closet pan (pedestal pattern) white,incl. P or S Trap , connection to drain and flushing pipe including seat cover for pedestal pan complete all as specified and as directed. |
| 15 | Supply and fixing in repairs Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified. |
| 16 | Supply and fixing in repair vitreous China squatting pan of pattern 'long pan', size 580mm white with 'P' or 'S' trap, front or back inlet and foot rests, any pattern including connection to drain and flushing pipe complete all as specified and as directed. |
| 17 | Supply and fixing in repairs vitreous China wash basin white, flat back, size 550X400 mm including cutting for pinning in ends of brackets, complete all as specified and as directed. |
| 18 | Supply and fixing in repairs 10 litre capacity PVC low level flushing cistern with all accessories fixed with WC including syphon pipe, PVC flushing pipe complete all as specified and directed. |
| 19 | Supply and fixing in repairs 15mm dia bore stop cock/angle cock, but fancy type chromium plated screwed down high pressure, with crutch or butterfly handle screwed both ends for iron pipe on for unions complete all as specified and directed. |
| 20 | All as per item No. 19 above but chromium plated with long shank and cup (Concealed type) all as specified and as directed. |
| 21 | Supply and fixing PVC connection 15mm dia and 450mm long with PTMT nuts complete all as specified and directed. |
| 22 | Supply and fixing in repairs bib taps cast copper alloy, fancy type 15mm dia bore, chromium plated, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed all as specified and as directed. |
| 23 | Supply and fixing in repairs brass chromium plated shower rose 125 mm size fixed to 15mm pipe, revolving type complete all as specified and directed. |
| 24 | Supply and fixing in repair grating square 150mm size of PTMT(minimum 100 gms) complete all as specified and directed. |
| 25 | Supply and fixing in repairs pillar taps,cast copper alloy, fancy type 15mm dia bore, chromium plated, screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed. |
| 26 | Supply and fixing in repairs 5.50mm thick of size 600*450 mm bevelled edge mirror of selected quality glass and fixed to walls using hidden studs complete all as specified and directed. |
| 27 | Supply and Fix in repair Vitreous China bowl Urinal , flat back, size of 465 x 355 x 265mm white (minimum), with grating and union for discharge pipe including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs brass screws pointing around urinal for discharge pipe complete all as specified and directed. |
| 28 | Supply and fixing in repair 75 mm dia PVC (SWR) Floor trap with grating including jointing with solvent cement complete all as specified and directed. |
| 29 | Supply and fixing in repair 110mm dia PVC (SWR) Gully trap setting and jointing with solvent cement complete all as specified and directed. |
| 30 | Supply and fixing rotational moulded polyethylene water storage tanks 1000 litres capacity (White colour), three layer (cylindrical or vertical with closed top) hoisted and fixed in position, including dismantling the existing one including supply and fixing 20 mm dia CPVC pipe medium grade, washout pipe 450 mm long with plug and 20 mm dia CPVC pipe medium grade overflow pipe 600 mm long with connected fittings, with 20mm dia bore Ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (Minimum weight 20 mm - 210 gms) and 20 mm dia gun metal, globe or gate valves, with iron head, screwed both ends for iron pipe complete all as specified and directed complete all as specified and directed. |
| 31 | Supply and fixing in repairs Towel rail 600 mm long of PTMT fixed with including chromium plated brass screws and wooden/plastic cleats (minimum weight 190 gms) all as specified and as directed. |
| 32 | Taking down old door or window or cup board Chowkhats or frames n.exc 1.50sqm each with shutters but without taking off shutters from the frames including 15mm thk plastering to jambs in CM 1:6 complete all as specified and directed. |
| 33 | Taking down door or window or cupboard Chowkhats of frames of size exc 1.5sq.m but n exc 4sqm each with shutters (Without taking of shutters from the frame) including 15mm thk plastering to jambs in CM 1:6 complete all as specified and directed. |
| 34 | Supply and fixing factory made uPVC white colour Casement door with 3D hinges made of (big series) frame 67 x 64 mm & sash 67 x 110 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws, etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality complete all as specified and directed by Engineer-inCharge. (Glass shall be paid separately) Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. |
| 35 | Providing and fixing factory made uPVC white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories. (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net Opening will be measured for payment purpose.) (A) Area not exceeding 2.00 sqm each |
| 36 | Providing and fixing factory made uPVG white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories. (B) Area exceeding 2.00 sqm each (Note for item 35& 36: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net Opening will be measured for payment purpose.) |
| 37 | Supply and fixing factory made uPVC white colour fixed glazed window/ventilator made of (small series) frame 47 x 50 mm mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area upto 0.75 sqm.) comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Glass shall be paid separately). Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. |
| 38 | Providing and fixing factory made uPVC white colour casement (Openable) window made of extruded profiles with wall thickness of 2.3mm ( + – 0.2mm). Window profile with hollow section with multi chamber, frame (60mm x 58mm), sash (60mm x 73mm), T profile (One vertical length in between two shutters) (60mm x 74mm), Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket 1.2 +– 0.2mm thick, galvanized steel Frame (28mm x 21.5mm), sash (31mm x 27.5mm). T profile (27mm x 17mm) to be inserted in required profile, frame will be fixed to the wall with 8 mm x 100mm long fasteners. Hardware: [casement handle made of zinc alloyed (white powder coated), But Hinges of' zinc alloyed (white powder coated), transmission gear made of mild steel with multi point locking system] and 5mm thick glazing with selected quality glass. Area n exe 1Sqm (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net opening will be measured for payment purpose.) |
| 39 | Supply and fixing factory made uPVC white colour Casement mesh door with 3D hinges made of (big series) frame 67 x 64 mm & sash 67 x 110 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws, etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality complete all as specified and directed by Engineer-inCharge. (Mesh shall be paid separately) Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. |
| 40 | Supply and fixing powder coated aluminium frame for doors, windows, ventilators, partitions with one or more rebates including anodised aluminium snap beading, stainless steel screws joining cleat for fixing etc complete all as specified and as directed |
| 41 | Supply and fixing powder coated (minimum thickness of powder coating 50 micron) Anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading screws etc. complete all as specified. |
| 42 | Supply and fix aluminium wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed. |
| 43 | Supply and fixing powder coated Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section weighing 2kg/Sqm around the opening, all complete as per requirement and direction of Engineer-in- charge. |
| 44 | Supply and fixing 4mm thick sheet glass frosted on one side ordinary quality fixing with necessary rubber gasket and beadings etc. in squares exc 0.50 sqm in each pane for window complete all as specified and as directed. |
| 45 | Supply and fixing 4.8mm thick sheet glass frosted on one side ordinary quality fixing with necessary rubber gasket and beadings etc in squares exc 0.50 sqm in each pane complete all as specified and as directed. |
| 46 | Supply and fixing Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site with particle board core as per specification & drawing complete all as specified and as directed. |
| 47 | Supply and fixing Factory made Solid PVC Door Frames of size 50mm*47mm made out of 5mm single side prelam PVC sheet used instead of Plain colour PVC sheet & edges will be painted to match with prelam sheet reinforced with M.S. Square tube, supplying & fixing in opening as per specification & drawing complete all as specified and as directed. |
| 48 | Supply and fixing 100mm stainless steel butt hinges medium weight including screws all as specified and as directed. |
| 49 | Supply and fixing aluminium anodised 200mm barrel tower bolts of extruded section complete all as specified and directed. |
| 50 | Supply and fixing aluminium handle 125mm cast type anodised complete all as specified and directed. |
| 51 | Supply and fixing 250mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed. |
| 52 | Supply and fixing MS flat iron as in hold fast clamps articles conforming to Fe 410 or Fe 310 complete all as specified and as directed. |
| 53 | Material and labour for PCC 1:3:6 type C1 (20mm graded aggregate) as in bed blocks for hold fast including necessary formwork complete all as specified and directed. |
| 54 | Supply and fixing 110mm dia PVC (SWR) vent cowl complete all as specified and as directed. |
| 55 | Taking down cement plaster of any description on bricks or stone walls , RCC ceiling etc, including raking out joints, hacking for keys, scrubbing down with water etc, all as specified and as directed. |
| 56 | Demolition of Brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and as directed. |
| 57 | Material and labour for 15 mm thick cement plaster in two coats 5mm thk in CM 1:4 with WPC over 10mm thk in CM 1:6 on brick wall or concrete surface and finish the surface fair and even complete all as specified and directed.Note: WPC will be measured and paid seperately as supply only under relevent items. |
| 58 | Material and labour for Preparation of new plastered surface of wall and applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces all as specified and as directed . |
| 59 | Material and labour for 10 mm thick cement plaster in CM (1:6) on brick wall and finish the surface even and smooth without using extra cement complete all as specified and directed. |
| 60 | Material and labour for preparation of new plastered wall surfaces and applying two coats of oil bound distemper over a coat of primer and 1mm thick wall care putty complete all as specified and as directed . |
| 61 | Material and labour for 10 mm thick cement plaster in CM (1:3) on ceiling and finish the surface even and smooth without using extra cement complete all as specified and directed. |
| 62 | Material and labour for preparation of newly plastered ceiling surfaces and applying two coats of oil bound distemper over a coat of primer all as specified and as directed. |
| 63 | Material and labour for complete removal of existing painted wall surfaces and applying two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over in camouflage pattern all as specified and as directed. |
| 64 | Material and labour for complete removal of existing painted wall surfaces and applying two coats of Oil bound distemper over a coat of primer over 1mm thk wall care putty complete all as specified and as directed. |
| 65 | Material and labour for complete removal of existing painted ceiling surfaces and applying two coats of Oil bound distemper over a coat of primer complete all as specified and as directed. |
| 66 | Material and labour for preparation of old painted wood or wood based surfaces over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed. |
| 67 | Material and labour for preparation of old painted steel/roof surfaces any description over 10cm girth and applying one finishing coat of synthetic enamel paint complete all as specified and as directed. |
| 68 | Taking down eaves gutter and rainwater (any size or pattern) including all fittings,heads,shoes,bends,swan necks etc. and cleaning or refixing or removal to store (measured over all fixed along the centre line over fittings and accessories) |
| 69 | Supply and fixing 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints, sealed with adhesive suitable for PVC pipes and fixed to walls including all scaffoldings arrangement complete all as specified and as specified. |
| 70 | Supply and fixing 110mm dia PVC (SWR) bends any radius at any height including scaffolding complete all as specified and as directed. |
| 71 | Supply and fixing 75mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints, sealed with adhesive suitable for PVC pipes and fixed to walls including all scaffoldings arrangement complete all as specified and as specified. |
| 72 | Supply and fixing 75mm dia PVC (SWR) bends any radius at any height including scaffolding complete all as specified and as directed. |
| 73 | Demolition of cement concrete in below or above ground floor & paving n exe 15cm thk unreinforced complete all as directed and as specified. |
| 74 | Material and labour for 75mm thk cement concrete type C1 1:3:6 (20mm graded aggregate) as in plinth protection finished even and fair without using extra cement complete all as specified and as directed. |
| 75 | Demolition of reinforced cement concrete as in roofs, floors, beams, staircase, landing, chajjas and similar suspended work all as specified and as directed. |
| 76 | Material and labour for RCC type B1 1:2:4 using 20mm graded aggregate as in chajja, fascia, fins complete all as specified and as directed. |
| 77 | Formwork to challah hoods, chajjas, trough and similar items including edges for fair finished surfaces all as specified and as directed. |
| 78 | Material and labour for TMT bars 10mm and over cut to length, bend to shape required including cranking, hooking ends and binding with and including MS wire (annealed) not less than 0.90mm dia complete all as specified and directed. |
| 79 | Material and labour for post constructional anti termite treatment along external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear meter including drilling and plugging holes etc. in apron complete all as specified and as directed. |
| 80 | Material and labour for anti termite treatment of soil under existing floor using emulsion @ one litre per hole, 300 mm apart including drilling and plugging 12 mm dia hole with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floors complete all as specified and as directed. |
| 81 | Material and labour for complete removal of existing roof treatment from roof slab including taking down existing cement mortar, cleaning of the rubbish and disposal of the same to a distance n exc 250 m ,providing screed bed or bedding layer of mortar 15mm thick in CM 1:4 with water proofing compound @ 3% of weight of cement and brushing neat cement slurry with 3.0 kg of cement per sqm complete all as specified and as directed. |
| 82 | Supply only integral water proofing compound |
| 83 | Material and labour for providing APP based membrane roof treatment in layers with the following course of treatment from bottom to top :- (a) Applying bituminous primer @ 0.30 Lit/Sqm over plastered surfaces of roof slab including parapet wall. (b) APP based polymeric membrane minimum weighing 3 kg/sqm and minimum 3mm thick reinforced with polyester non wove fabric (wt. not less than 150 gms/sqm) laid on primed surface by torch application . Polymeric membrane shall be taken to a height of 45 cm (minimum) and then inserted inside the groove of parapet wall and shall be finished by a membrane flashing. (c) Surfaces to be painted with bituminous aluminium paintNote: (i) The work in respect of water proofing treatment shall be carried out only by authorised / approved applicator of the manufacturers / firms of APP membrane. The contractor shall produce the evidence in support of work carried out by the authorised applicator as approved by manufacturers / firms before claiming payment. (ii) Laying APP based polymeric membrane shall be done by torch on method or as per manufacturers instructions. (iii) A minimum overlap of 100 mm and 75 mm should be made at the end and side of the polymeric membrane respectively and sealed overlaps and joints as per manufacturers instructions. (iv) Coved fillets in PCC(1:2:4) type B-0 using 12.5mm graded stone aggregate, of radius 75mm shall be provided at the junction of roof and parapet wall/mumty/chimney/other vertical surfaces. |
| 84 | Material and labour for Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:3 complete all as specified and as directed. |
| 85 | Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and as directed. |
| 86 | Material and labour for RCC M-30 (Design mix) using 20mm graded aggregate on slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed |
| 87 | Providing 30mm thick PVC flush door shutter consisting of frame made out of MS Tubes of 19 gauge thickness and size of 20 mm x 40 mm for stiles as well as top, bottom and lock rail. MS Frame shall have a coat of metal primer of approved make & manufacturer. The inside panel shall consist of 20mm thick multichamber hollow PVC section of 1 mm wall thickness bonded using solvent cement / cynoacrylate adhesive with 5mm (+-0.25) thick plain PVC sheet of Density 600Kg / CBM manufactured by an ISO 9001-2015 certified company on both side of inside panel. All the four edges of the panel to be sealed with lipping of 10mm thick and 20 mm wide PVC Sheet batten (made by sticking 2 Nos PVC Sheets of 5 mm (+-.25) thickness using PVC Solvent cement adhesive. Door edge lipping to be painted with PVC ink of matching colour of plain / pre laminated PVC of door 20 mm thick (5mm x 4 Nos) thick PVC Sheet to be given for lock provision of lock height. Door to be fixed with frame with 3 Nos SS Butt hinges of size 100 mm x 25 mm x 2 mm and 50 mm long steel screws drilled suitable to pass through both the wall of MS Tube other Hardware should be fixed with 25 x 8 mm size steel screws etc. complete as per direction of Engr-in-Charge manufacturer's specification and drawings. |
| 88 | Surface excavation n.exc (not exceeding) 30cm deep and averaging 15cm deep and getting out in soft loose soil complete all as specified and as directed. |
| 89 | Material and labour for Hard core using broken stone or boulders of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and as directed. |
| 90 | Material and labour for cement concrete 100 mm thick type D2 1:4:8 using 40 mm graded aggregate as in sub base in floor complete all as specified and as directed. |
| 91 | Material and labour for Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and as directed. |
| 92 | Excavating in post holes (or similar holes) each n exc 0.5cum, getting out, returning, filling in soft soil and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering, and removing surplus soil to a distance n exc 50m and making good surface complete all as specified and as directed. |
| 93 | Material and Labour for PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in foundation complete all as specified and as directed. |
| 94 | Material and Labour for PCC 1:2:4 type B-1 using 20mm graded stone aggregate as in foundation, filling mass concrete complete all as specified and as directed. |
| 95 | Material and labour for Brick work with sub class 'B' brick straight or curved on plan exc 6m mean radius and built in CM 1:4 complete all as specified and as directed. |
| 96 | Supply and fixing rolled sections as in main and cross beam, hip and jack rafter purlins where connected to common rafter and running rails and guides for sliding door, fixed with angle cleats or other connecting plates etc conforming to Fe 410-W (Gde-E-250) complete all as specified and directed. |
| 97 | Supply and fixing Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel, hollow or flat sections) including distance pieces, cleats with Fe 410 -W (Gde E- 250) quality A etc. complete all as specified and as directed. |
| 98 | Supply and fixing Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment with Fe 410 -W (Gde E- 250) quality A complete all as specified and as directed. |
| 99 | Material and labour for preparing new or previously untreated steel surface of any description, over 10cm in width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed. |
| 100 | Supply and fixing pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.5mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and as directed. |
| 101 | Supply and fixing pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.5mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and as directed. |
| 102 | Supply and fixing 2mm thk Fibre glass reinforced translucent corrugated sheeting with two corrugations side lap fixed with coach screw and washer in roof, wall (bend to shape) etc. complete all as specified and as directed. |
| 103 | Supply and fixing Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing including locking arrangement complete all as specified and as directed. |
| 104 | Supply and fixing in repairs 32mm dia Low density polyethylene pipes(LDPE) of pressure rating 6 kg/ cm2 on wall complete all as specified and as directed. |
| 105 | Supply and fixing sign board made of 2mm thick acrylic sheet, coloured with reflective stickers and fixed in position with screws on supports with desired letters as directed by Engr In Charge. |
| 106 | Supply and fixing in repairs Harrison curtain rails with brackets, mild steel, chromium plated, stops, rollers etc. complete all as specified and as directed. |
| 107 | Supply and fixing in repairs Waste coupling along with pipe of PTMT (half or full threaded) (Minimum weight 32mm -45gms) for urinals complete all as specified and as directed. |
| 108 | Material and labour for 12mm thk prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and as directed. |
| 109 | Earth work in excavation by mechanical means (Hydraulic excavator) over areas (not exceeding 1.5m in depth including getting out in all kind of soil and disposal of excavated earth lead up to 50 m and lift up to 1.5m,complete all as specified and directed by Engineer-in charge |
| 110 | Earth work in excavation by mechanical means (Hydraulic excavator) over areas (exceeding 1.5m in depth) including getting out in all kinds of soil and disposal of excavated earth lead upto 50 m and lift upto 1.5m, complete all as specified and directed by Engineer-in charge |
| 111 | Material and labour for cement concrete 1:3:6 Type C2 (using 40mm graded coarse aggregate) in mass concrete complete all as specified and directed by Engineer-in charge |
| 112 | Formwork to sides of concrete, foundations, footing, bases of columns, raft and raft beams, sides of soffits (if any) of foundation and plinth beams ; and similar work; vertical or to batter complete all as specified and directed by Engineer-in charge |
| 113 | Formwork to faces of walls and similar work; vertical or to batter complete all as specified and directed by Engineer-in charge |
| 114 | Material and labour for RCC M-30 (Design mix) using 20mm graded aggregate in foundations, including rafts, footing, foundation beams; plinth beams; bases for columns, etc; basement slabs, under reamed piles and mass concrete complete all as specified and directed by Engineer-in charge |
| 115 | Material and labour for RCC M-30 (Design mix) using 20mm graded aggregate in walls, retaining walls, basement walls, ballast walls and the like; any thickness; above top of footing; including attached pilasters and buttresses complete all as specified and directed by Engineer-in charge |
| 116 | Material and labour for RCC M-30 (Design mix) using 20mm graded aggregate as in slab supported on wall, beams and columns in floors, roofs, landing, balconies, canopies, deck slabs and in shelves complete all as specified and directed by Engineer-in charge |
| 117 | Material and labour for rendering 20mm thick on fair faces of brick work or concrete surfaces in CM 1 : 4 mixed with WPC @ 3 % by the weight of cement and finished even and smooth without using extra cement complete all as specified and directed.Note: WPC will be measured and paid for seperately under relevant item |
| 118 | Material and labour for cement concrete 1:3:6 Type C2 (using 20mm graded coarse aggregate) 75 mm thick in padding complete all as specified and directed by Engineer-in charge |
| 119 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in any type of soil complete all as specified and directed by Engineer-in charge |
| 120 | Demolition of cement concrete reinforced cover slabs of man holes etc n.exc 15 cm thick all as specified & directed. |
| 121 | Material and labour for pre cast reinforced cement concrete manhole cover 1:2:4, type B1, (Using 20mm graded stone aggregate) set in CM 1:4 complete including necessary formwork complete all as specified and as directed. |
| 122 | Supply and fixing mild steel TMT bars 6mm to 8mm dia cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engineer-in charge |
| 123 | Excavation in trenches, not exceeding 1.5 M wide, and not exceeding 1.5 M in depth for foundation etc and getting out in soft soil all as specified. |
| 124 | Removing excavated material to a distance n.exc 50m & depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and directed by Engineer-in charge |
| 125 | Material and labour for Plain cement concrete 1:3:6 type C2 (using 40mm graded granite stone aggregate) as in concrete bed to drain pipes for 150 mm dia including packing under and haunching against the sides of pipes after they are laid and tested complete all as specified and directed. |
| 126 | Demolition and breaking up SWG drain pipe of 150mm dia set in cement concrete as in trenches as directed by Engr-in-charge. |
| 127 | Material and labour for 150mm dia Reinforced concrete pipes, class NP2, laid and jointed complete with collars as specified and as directed by Engr-in-Charge |
| 128 | Material and labour for Rendering 15mm thick in CM 1:4 on fair faces of brick work or concrete wall surfaces finished fair and even all as specified and directed. |
| 129 | Material and labour for PCC (1:2:4), type B2 using 40mm aggregates in haunching, surface channel & drains complete all as specified & directed. |
| 130 | Material and labour for Plain cement concrete 1:3:6 type C2 (using 40mm graded stone aggregate) in surface channels and drains complete all as specified and directed. |
| 131 | Material and labour for providing cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate cast in situ as in copings and the like including weathering, slightly rounded or chamfered or chamfered angles and throating including use of form work as necessary all as specified and as directed. |
| 132 | Material and labour for Forming fair finish drain or channel 30cm inner girth in cement concrete using extra cement complete all as specified and as directed. |
| 133 | Removing excavated material/soil to a distance not exc 250 mtr but n exc 500 m away and depositing as directed at a level not exceeding 1.5 mtr above the starting point, complete all as specified and directed by Engr-in-charge. |
| 134 | Sch A Part II (E/M portion) |
| 135 | Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc., removing materials to store for keeping in safe custody for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors etc. complete all as specified and as directed by the Engineer-in-Charge. |
| 136 | Material and labour for point wiring with three single core 1100 V grade conforming to IS-694 PVC insulated sheathed FRLS cables of size 1.5 Sqmm multi-stranded copper conductor for phase, neutral & earth drawn through and including rigid PVC conduit and conduit accessories fixed on concealed including cutting of walls and making good to disturbed surfaces in wall/ floor/ ceiling, etc., where required complete with sheet metal sunken box including modular cover plates and frame and connecting earth wire to metal boxes and common earth dolly all as specified and directed for the following :- |
| 137 | One light point, controlled by one switch |
| 138 | One fan point, controlled by one switch |
| 139 | One 6 Amps socket point on independent board |
| 140 | One 6 Amps socket point on same board with other switches |
| 141 | All as per item No. 136 above but with three run of 4.0 Sqmm PVC insulated sheathed FRLS cables for 16 amps independent socket. |
| 142 | Supply and fixing ceiling rose in replacement, surface Bakelite, 65x50mm, two to three terminals all as specified and as directed by the Engineer-in-Charge |
| 143 | Supply and fix modular switch single pole one way 6 A 240 Volts complete. |
| 144 | Supply and fix modular switch single pole one way 16 A 240 Volts complete. |
| 145 | Supply and fix modular socket 6A, 2/3 pin combined 2 module complete all as specified and as directed. |
| 146 | Supply and fix modular socket 6A/16A, 2/3 pin combined 2 module complete all as specified and as directed. |
| 147 | Supply and fix stepped type electronic fan regulator 120W, 2 module complete all as specified and as directed. |
| 148 | Material and labour for sub main wiring with two runs of single core 6 sqmm multi stranded copper conductor PVC insulated unsheathed cable 1100 volts grade and one run of 6 sqmm multi stranded copper conductor cable as earth continuity conductor drawn into and including non-metallic rigid concealed PVC conduit of 25 mm dia including taking down old existing sub main wiring complete all as specified and directed.Note: Three runs of 6 Sqmm cable and one run of 25 mm conduit will be measured as one unit length. |
| 149 | Material and labour for sub main wiring with two runs of single core 4 sqmm multi stranded copper conductor PVC insulated unsheathed cable 1100 volts grade and one run of 4 sqmm multi stranded copper conductor cable as earth continuity conductor drawn into and including non-metallic rigid concealed PVC conduit of 25 mm dia including taking down old existing sub main wiring complete all as specified and directed.Note: Three runs of 4 Sqmm cable and one run of 25 mm conduit will be measured as one unit length. |
| 150 | Supply and fix sheet metal enclosure powder coated double door for distribution board, SPN 12 way, 240 V with box insertion marks, circuit identification label, neutral link, earth link, etc., including, disconnecting electric connections, dismantling old unserviceable DBs for taking into credit complete all as specified and as directed. |
| 151 | Supply and fix sheet metal enclosure powder coated double door for distribution board, TPN 4 way 415V, with circuit identification label, neutral link, earth link, etc., including, disconnecting electric connections, dismantling old unserviceable DBs for taking into credit complete all as specified and as directed. |
| 152 | Supply and fix sheet metal enclosure powder coated double door for distribution board, VTPN 4 way 415V, IP54, with neutral link, earth link, etc., including, disconnecting electric connections, dismantling old unserviceable DBs for taking into credit complete all as specified and as directed. |
| 153 | Supply and fix MCB TP 50A / 63 A, C curve including removing old unserviceable MCB for taking into credit complete all as specified and as directed. |
| 154 | Supply and fix MCB TPN 100A, C curve including removing old unserviceable MCB for taking into credit complete all as specified and as directed. |
| 155 | Supply and fix MCCB four pole 415 volts 50 Hz, 125A, with rupturing capacity 25 KA complete all as specified and as directed including taking down old unserviceable MCCB for taking into credit complete all as specified and as directed by the Engineer-in-Charge. |
| 156 | Supply and fix sheet metal enclosures with two pin and earth socket & plug top with MCB SP 20A, 240 volts, complete with one single MCB 20 Amps, 240 volts (for AC) including taking down old unserviceable sheet metal enclosures complete all as specified and directed. |
| 157 | Supply and fix in replacement MCB SPN 40 A, C curve, 10 kA complete all as specified and as directed. |
| 158 | Supply and fix in replacement MCB SP 6 A to 32 A, B curve, 10 kA complete all as specified and as directed. |
| 159 | Supply and fix in replacement MCB SP 40A, B curve, 10 kA complete all as specified and as directed. |
| 160 | Supply and fix LED batten 20W with decorative end cap with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable of suitable size complete all as specified and directed |
| 161 | Supply and fix in repairs GI bracket made out of 32 mm dia GI pipe, medium grade of length 1.2 mtr long bent to an angle of 135 degree including two coats of aluminium paint over a coat of zinc chromate primer along with clamps, bolts, nuts etc complete all as specified. |
| 162 | Supply and fixing energy saving LED security light fittings, 35 Watts or nearest higher wattage, with in-built electronic driver, IP 66 class of protection with versatile pressure die-cast aluminium body, toughened glass cover with silicon gaskets and energy efficient LED and connecting up light fitting with copper conductor cable of suitable size from junction box to connector block including all accessories and taking down old unserviceable fitting for taking into credit complete all as specified and as directed. Please Enable Macros to View BoQ information |
| 163 | Supply and fixing energy saving LED security light fittings, 35 Watts or nearest higher wattage, with in-built electronic driver, IP 66 class of protection with versatile pressure die-cast aluminium body, toughened glass cover with silicon gaskets and energy efficient LED and connecting up light fitting with copper conductor cable of suitable size from junction box to connector block including all accessories and taking down old unserviceable fitting for taking into credit complete all as specified and as directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 17, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 13, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 12 daysAug 15, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 14 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender