Tender For Special Repair To Building No. Ta-159/0/10, T-822, T-310, T-280, Ta-158/09 And Constr Of Toilet Block With Sockage Pit At Karu Under Age Br-I Under Ge 860 Ews
Tender Value
47.93 Lakhs
Estimated cost
Bid Submission
07 Aug 2026
11 days left
EMD
96000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
karu → Ladakh
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Special Repair To Building No. Ta-159/0/10, T-822, T-310, T-280, Ta-158/09 And Constr Of Toilet Block With Sockage Pit At Karu Under Age Br-I Under Ge 860 Ews
Corrigendum
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 25-Jul-2026 | Revised BOQ | BOQ | 07-Aug-2026 |
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling of boarding in wall/ceiling, any description, fixed in any position with nails or screws complete all as specified and directed by Engr-in Charge |
| 2 | S&F Gl frame work for seamless wall/ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre. with necessary fastening GI wire and cleats including 12 mm thick Gypsum board fixed in wall/ceiling with screw as per manufacturer instruction including plaster of paris putty of 2 mm thick and two coats of distempering with Ist quality acrylic distemper ( ready Mixed ) having VOC content less than 50 gms/ ltrs, of approved manufacturer , of required shade and colour complete over a coat of primer complete all as specified and directed by Engr-in-Charge. |
| 3 | S&F of coloured PVC designer modular wall cladding 5 to 6 mm thick with air gap, installed with necessary fixing GI channel or frame with end joints on edges ( designed colour patterns as per directed by Engr - in- charge). The frame work will be fixed to wall using aluminium screws complete all as specified and as directed by Engr-in- Charge .Note : if necassary size of the frame work/ wall paneling will be changed as per site requirement. |
| 4 | M&L for 9mm thick pre-laminated particle board, interior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination fixed with screws/nails to timber frame work in wall/ceiling portion all as specified and directed by Engr-in-Charge. |
| 5 | Dismantling of timber fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section frame work complete all as specified and directed by Engr in Charge |
| 6 | M&L second class hard wood timber scantling plain fillets square, rectangular or triangular in section, clean sawn, secured with nails or brads, sectional area exc. 13 Sq cm n.exc 25 Sq cm secured with nails or brads.complete all as specified and directed by Engr in Charge |
| 7 | M&L for 2nd class soft wood fillets sectional area exc 3 and n exc 6 sqcm rectangular or triangular in section but bullnosed, splayed, chamfered or rounded on one edge of face, secured with nails or brads, complete all as specified and as directed by Engr-in-Charge. |
| 8 | Hacking out old broken glass (any thickness, size, quality or description) from from metal frame including punching or drilling out old glazing pins/spring clips and providing, complete all as specified and directed by Engr-in-Charge. |
| 9 | S&F of 4mm thick sheet glass, ordinary quality and glazing with oil putty and glazing pins in square n exc 0.5 sq. m in each pane complete all as specified and directed by Engr-in-Charge. |
| 10 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing dismantled tile and rubbish off the premises complete all as specified and directed by Engr-in-Charge. |
| 11 | M&L Glazed ceramic coloured tiles in vertical surface 450X 300X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match and joint free including 10 mm thick baking coat in CM 1:3. for laying floor finishes receiving floor tiles complete all as specified and directed by Engr-in-Charge. |
| 12 | S&F in repair Veneered decorative plywood of 12mm thick, grade 1 (with BWR resin) with decorative face veneers on both faces; fixed with screws to timber frame work work complete all as specified and directed by Engr-in-Charge. |
| 13 | S&F in repair Rim latch with two levers, of brass body. stove enamelled finish; with brass knob or lever handle and fixed complete all as specified and directed by Engr-in-Charge. |
| 14 | S&F in repair Continuous (piano) hinges width of 30mm, Brass, bright finish or electrogalvanised complete all as specified and directed by Engr-in-Charge. |
| 15 | S&F in repair Magnetic catches, and brass body and striking plate including letting in and fixed complete all as specified and directed by Engr-in-Charge. |
| 16 | Dismantling post or struts (wood, steel or RCC) any section incl taking out embedded portion in concrete, brick work, masonry etc and making good disturbed ground complete all as specified and directed by Engr-in-Charge. |
| 17 | Excavating in post holes (or similar holes) in hard/dense soil each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, complete all as specified and directed by Engr-in-Charge. |
| 18 | M&L Cement concrete type C2 1:3:6 (40mm graded aggregate) in foundations, post hole, filling and mass concrete etc complete all as specified and directed by Engr-in-Charge. |
| 19 | Dismantling wrought iron or mild steel work of any description not otherwise provided for Complete all as specified and as directed by Engr-in-charge. |
| 20 | S&F of mild steel work in angle iron posts & struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe – 290 Gde E -165complete all as specified and directed by Engr-in-Charge. |
| 21 | S&F Rolled MS Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc conforming to Fe-290 Gde E-165), complete all as specified and directed. |
| 22 | Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof covering or wall etc complete all as specified and directed by Engr-in-Charge. |
| 23 | S&F Galvanised corrugated mild steel sheeting 0.63mm thick with two corrugation side lap, fixed withL-type or J-type or cranked hook bolts and washers as in roofs, walls etc complete all as directed by Engr-in-Charge. |
| 24 | S&F 0.63mm thick Plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed), with grade of zinc coating 275 as complete all as specified and direct by Engineer-in-Charge. |
| 25 | M & L for two coat of synthetic enamel paint of approved tint on steel and iron surfaces of any description over 10 cm width or girth not otherwise described including preparing new zinc(or galvanised) surfaces to receive painting by coating with mordant solution incl washing and cleaning, etc. over a coat of red oxide complete all as specified and directed. |
| 26 | M&L for false ceiling 6 mm thick veneered decorative plywood ,grade 1 (with BWR resin) with decoretive face veneers on one faces ; fixed with screws to timber frame works complete as directed by E-in charge . |
| 27 | M&L Non - skid Ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.36 sqm, in floors 1:4 CM 15 mm. etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with 15 mm CM 1:4 sceed bed complete all as specified and directed by Engr-in-Charge. |
| 28 | Demolition of cement concrete (Unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and as directed. |
| 29 | M&L for 75 mm thick Cement concrete type C-2, 1:3:6 (20mm graded crushed stone aggregate) as in floor plinth protection, finishing cement concrete surface even and smooth without using extra cement complete all as specified and directed. |
| 30 | M&L for Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet .50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and directed by Engr-in-Charge. |
| 31 | M&L for Pre- painted galvatume aluminum zinc coating GI based plain steel sheet .50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and directed by Engr-in-Charge. |
| 32 | S&F in repair Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle,Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge. |
| 33 | S&F Sheet glass of size 5.5 mm thick ordinary quality and glazing with with beads fixed with metal panel pins/neoprene beadings, size of pane/ partition n exc 0.5 sq. m in each. |
| 34 | M&L 9 mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with nails to timber frame work in Ceiling and Ceiling complete all as specified and as directed by E-in charge .(Note : 1. Ladders, scaffolding will be provided by Contractor where required. |
| 35 | S&F in repair for SDC Laminated flooring 8mm thick of any coloured, manufactured by Direct Pressure Laminated (DPL) wherein the empty Abrasive aluminium oxide overlay alongwith metamine impregnated decorated film is directly fused with the back with flooring locking profile in designed with double click locking system on the length and single locking width alongwith desire locking strength laid over 1mm thick foam base, complete including removal of existing flooring, all as directed by the Engr-in-Charge. |
| 36 | Taking down chowkhats or frame exc 1.50 sqm each but n exc 4 sqm each with shutters (without taking off shutters from the frame) complete all as specified and directed by Engr-in Charge |
| 37 | S&F for 2nd Class hard wood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified and directed |
| 38 | S&F 35 mm thick Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed by Engr in Charge |
| 39 | M&L for preparation of new or previously untreated wooden surfaces of any description not otherwise described over 10cm in width or girth and applying two coats of synthetic enamel paint (1st grade quality) over a coat of pink primer complete all as specified and directed by Engr-in-Charge. |
| 40 | S&F 100 mm Butt hinges, medium weight, cold rolled mild steel, and fixed complete all as specified and directed by engr in charge |
| 41 | S&F 200mm Aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed by engr in charge |
| 42 | S&F 150mm Aluminium handles, cast type, anodised complete all as specified and directed by engr in charge |
| 43 | S&F 150mm Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed by engr in charge |
| 44 | S&F 250 mm Aluminium alloy, anodised,sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixedcomplete all as specified and directed by engr in charge |
| 45 | Supply and fixing 3 mm sheet glass thick ordinary quality and glazing with oil putty in squares n. exc 0.5 Sqm in each pane complete all as specified and directed by Engr-in-charge. |
| 46 | M&L 600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and as directed by Engr-in-Charge |
| 47 | S&F M&L for readymade soft wood wall /Ceiling panelling in strips of 100 mm width 10mm thickness having lounge and groove fixing arrangements fixed to wooden frame work(Size of frame work 1.2X1.2 C/C included ) as per manufacturers instruction including polishing complete all as specified and as directed by Engr-in- Charge .Note : if necassary size of the frame work/ wall paneling will be changed as per site requirement without any cost different complete all as specified and directed by Engr-in-Charge. |
| 48 | S&F for 30mm thick 2nd class hardwood Plain, framed, panelled door shutters(any number of panels), with panels of timber flat on both sides(feather edged), veneered particle board medium density, wood particle board with commercial face veneers, supplied and fitted to chowkats complete all as specified and directed by Engr-in-Charge. |
| 49 | S&F in repair sinks made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.complete all as specified and directed by Engr-in-Charge. |
| 50 | Demolition Stone slabs and tiles Laid beded and pointed cement mortar of any description or thickness in floors, aprons etc. all as specified and directed by Engr-in Charge. |
| 51 | M&L Granite 25 mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and Providing edge moulding to 18-20mm thick granite stone of counters vanities etc. including machine polishing to edge to give high gloss finish etc. complete all as specified and directed by Engr-in-Charge. |
| 52 | M&L Providing edge moulding to 18-20mm thick granite stone of counters vanities etc. including machine polishing to edge to give high gloss finish etc. complete all as specified and directed by Engr-in-Charge. |
| 53 | M&L for preparation/removal of old painted steel surfaces and applying two coat of synthetic enamel paint on surface of any description over 10cm width or girth complete all as specified and directed by Engr-in-Charge. |
| 54 | Demolition and breaking up drain pipes (salt glazed ware, PVC or re-inforced concrete) set in cement mortar internal dia of pipe 100mm complete all as specified and directed by Engr-in-Charge. |
| 55 | S&F 110mm dia bore PVC (SWR) pipes single socketed in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed by Engr-in-Charge. |
| 56 | M&L PCC 1:3:6 type C-2 as in 110mm bore of pipe in concrete bed to drain pipes including packing under and haunching against the sides of pips after they are laid and tested complete all as specified and directed by Engr-in-Charge. |
| 57 | S&F 110mm dia bore PVC (SWR) bends complete all as specified and directed.complete all as specified and directed by Engr-in-Charge. |
| 58 | S&F for Stainless steel pressed handles 100 mm size complete fixed complete all as specified and directed. |
| 59 | M&L Non - skid coloured Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and joint free including 15 mm thick screed bedding in CM 1:4. for laying floor finishes receiving floor tiles complete all as specified and directed by Engr-in-Charge. |
| 60 | S&F in repair for 15 mm bore chromium plated fancy type Bib taps, cast copper alloy with crutch or above butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed (minimum weight 575 grams) complete all as specified and directed. |
| 61 | Demolition of stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles, complete all as specified and directed by Engr-in-Charge. |
| 62 | M&L Pre-cast cement concrete block masonry type C1 1:3:6 (20mm graded aggregate) with solid blocks, 10cm in thick and, setting in cement mortar 1:4 complete all as Specified and directed by Engr-in-Charge. |
| 63 | Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out Hard /Dense Soil. complete all as specified and directed by Engr-in-Charge. |
| 64 | Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and getting out in hard/dense soil complete all as specified and directed by Engr-in-Charge. |
| 65 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm. complete all as specified and directed by Engr-in-Charge. |
| 66 | Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed by Engr-in-Charge. |
| 67 | M & L for Cement concrete type D-2, 1:4:8 (Using 40mm graded stone aggregate) in foundations, filling and mass concrete complete all as specified and directed by Engr-in-Charge. |
| 68 | M & L for RCC 1:2:4, Type B0 (Using 12.5 mm graded stone aggregate) nominal mix in footing,plinth beam complete all as specified and directed by Engr-in-Charge. |
| 69 | M&L Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter flat rough finished surface of concrete omplete all as specified and directed by Engr-in-Charge. |
| 70 | M&L for RCC 1:2:4, Type B0 (Using 12.5 mm graded stone aggregate) nominal mix Columns, pillars, piers, posts and struts complete all as specified and directed by Engr-in-Charge. |
| 71 | M&L Formwork to sides of pillars, posts, struts, piers, columns and stanchions for fair finished surface square, rectangular complete all as specified and directed by Engr-in-Charge. |
| 72 | M&L for RCC 1:2:4, Type B0 (Using 12.5 mm graded stone aggregate) nominal mix Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed by Engr-in-Charge. |
| 73 | M&L Formwork flat and fair finished to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels beam, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc complete all as specified and directed by Engr-in-Charge. |
| 74 | M & L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engr-in-Charge. |
| 75 | M & L for 6 to 8 mm dia Mild steel TMT bar in stirrups, spacers and binders complete all as specified and directed by Engr-in-Charge. |
| 76 | M&L Pre-cast cement concrete block masonry type C1 1:3:6 (20mm graded aggregate) with solid blocks, exc. 10cm in width and, setting in cement mortar 1:6 complete all as Specified. |
| 77 | M&L Pre-cast cement concrete block masonry type C1 1:3:6 (20mm graded aggregate) with solid blocks, 10cm in thick and, setting in cement mortar 1:4 complete all as Specified. |
| 78 | S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing |
| 79 | S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing |
| 80 | S&F aluminium anodised window and ventilator shutter, side hung type without sash bars aiuminium section weighting 0.55 kg/m including nessary joint cleats, glazing clips, ruber neoprene packing, aluminium snap beading screw anodised alumimium fittings such as peg stays 150mm long (1 No), hinges type B-21 100mm long (02 Nos), suitable handle (01 No), complete all as specified and directed. |
| 81 | S&F of 4mm thick figured glass, pin head type and glazing with oil putty and glazing pins in square n exc 0.5 sq. m in each pane complete all as specified and directed by Engr-in-Charge. |
| 82 | S&F Aluminium alloy barrel tower bolt of extruded type 150 mm long complete all as specified and directed by Engr-in-Charge. |
| 83 | M&L for two coat of synthetic enamel paint over a coat of red oxide on new steel surfaces of any description, not otherwise described over 10cm width or girth etc complete all as specified and directed by Engr-in-Charge. |
| 84 | M & L for Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 10 cm thick, watered and rammed to a true surface complete all as specified and directed by Engr-in-Charge. |
| 85 | M & L for 100mm thick Cement concrete type D- 2, 1:4:8 (Using 40mm graded stone aggregate) in sub base complete all as specified and directed by Engr-in-Charge. |
| 86 | M & L for 10 mm thick rendering in cm (1:6) on fair faces of brick work or concrete surface (Internal Plaster ) finished the surface even & smooth without using extra cement, complete all as specified and directed by Engr-in-Charge. |
| 87 | M & L for 15 mm thick rendering in cm (1:4) on fair faces of brick work or concrete surface finished the surface even & smooth without using extra cement, complete all as specified and directed by Engr-in-Charge. |
| 88 | Supply only water proofing compound (integral) all as specified & directed. |
| 89 | M & L for 25mm thick Cement concrete type B- 2, 1:2:4 (Using 20mm graded stone aggregate) in floor to recive tile complete all as specified and directed by Engr-in-Charge. |
| 90 | M & L for preparation of newly plastered wall / pillasters / vertical surface and applying two coats of cement base paint over a coat of alkali resistance primer complete all as specified and directed by Engr-in-Charge. |
| 91 | M&L preparation of new plastered or unplastered surfaces and applying two coats of oil bound distemper on wall over a coat of alkali resistant primer complete all as specified and darected. |
| 92 | S&F vitreous china water closet (squatt pan) orrisa pattern 580x440 mm (IWC) size pan white with front or back inlet with integral 'foot rests including provn of lime concrete bedding including connections to 'flushing cistern/pipe complete all as specified and directed including 100mm CI 'P' trap etc complete all as specified and directed by Engr-in-Charge. |
| 93 | S&F PVC 10 Ltrs valve less, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete with 32 mm dia flush pipe connecting to squatt pattern etc. ISI approved etc complete all as specified and directed by Engr-in-Charge. |
| 94 | M&L Vitreous China Urinal, full stall type, white (excluding flushing cistern, flush pipe and waste pipe) with urinal spreader,waste coupling and brackets including fixing etc complete all as specified and directed by Engr-in-Charge. |
| 95 | S&F 20mm 3-layer PP-R Polypropylene random copolymer) concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc complete all as specified and directed by Engr-in-Charge. |
| 96 | S&F rotational moulded polythylene water storage tanks 1000 ltrs ( cylindrical vertical with closed top) hoisted and fixed in position all specified complete all as specified and directed by Engr-in-Charge. |
| 97 | S&F 20mm PP-R gate valves (Brass insert), as per requirment of the site complete all as specified and directed by Engr-in-Charge. |
| 98 | S&F angle stop valves 15mm bore chromium plated, cast copper alloy screwed down high pressure with capstan head handle screwed both ends for iron pipe or for union complete all as specified and directed by Engr-in-Charge. |
| 99 | S&F PVC connection 15 mm bore 450mm long with screwed socket of brass on both ends and rubber washer.complete all as specified and directed by Engr-in-Charge. |
| 100 | S&F of plain flexible PVC waste pipe of 32mm dia, 800mm long complete all as specified and directed by Engr-in-Charge. |
| 101 | M&L Providing, cement concrete in roof kerbs or mud stops, rounded or chamfered on edges (above wall for coping) Type C 1 1:3:6 (20mm graded aggregate) complete all as specified and directed by Engr-in-Charge. |
| 102 | M&L Concrete bed 1:4:8 type D-2 to drain pipes incl packing under and haunching against the sides of pipes after they are laid and tested bore of pipe in 110 mm.complete all as specified and directed by Engr in Charge. |
| 103 | M&L 75MM dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, complete all as specified and directed by Engr-in-Charge. |
| 104 | S&F 110mm dia bore PVC (SWR) junction single, (single T) equal or unequal complete all as specified and directed by Engr-in-Charge. |
| 105 | S&F 75mm dia PVC (SWR) floor trap plain with grating including jointing to waste pipe fixed in solvent cement or cement concrete 1:2:4 type B1 complete all as specified and directed by Engr-in-Charge. |
| 106 | Excavation over areas n.exc 1.5m deep and and getting out in hard/dense soil, complete al |
| 107 | Excavation over areas exc 1.5m deep and n.exc 3.00 m deep and getting out in hard/dense soil |
| 108 | M & L for Walling of random rubble uncoursed, well bonded, bedded and solidly hearted, built in CM 1:4 complete all as specified and directed |
| 109 | M & L for Walling of random rubble stone masonary, uncoursed, well bonded, bedded and solidly hearted, laid dry complete all as specified and directed |
| 110 | M & L for rough finished Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) all as specified and directed. |
| 111 | Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roof n.exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10 cm but n.exc 20 cm wide. |
| 112 | M & L for TMT bars 10mm dia and over (12mm), cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips |
| 113 | M & L for providing RCC type B-1 1:2:4 using 20 mm graded aggregate in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like all as specified and directed. |
| 114 | M & L for precast cement concrete 1:2:4 type B-1 using 20mm graded aggregate as in cover slab for manhole set in CM 1:4 including necessary form work complete all as specified and directed by Engr in Charge. |
| 115 | M&L 75 MM dia PVC (SWR) vent cowl for Vent Pipe complete all as specified and directed by Engr-in-Charge. |
| 116 | Taking down carefully alluminium / copper point wiring complete for light, fan, socket or power point etc with fittings fixtures such as ceiling rose, holders, electric fittings, switchs, sockets, aluminium conductor cable with and incl wooden batten or FR PVC conduit and its accessories such as wooden gutties, rawl plugs, GI screws, aluminium clips, nails etc complete and removing the material from site and making good the disturbed surface of wall / floor/ ceiling etc as original i.e. brick work, plastering, white washing, OBD etc as required, complete all as specified and directed by Engr-in Charge. Please Enable Macros to View BoQ information |
| 117 | Taking down carefully alluminium / copper point wiring complete for light, fan, socket or power point etc with fittings fixtures such as ceiling rose, holders, electric fittings, switchs, sockets, aluminium conductor cable with and incl wooden batten or FR PVC conduit and its accessories such as wooden gutties, rawl plugs, GI screws, aluminium clips, nails etc complete and removing the material from site and making good the disturbed surface of wall / floor/ ceiling etc as original i.e. brick work, plastering, white washing, OBD etc as required, complete all as specified and directed by Engr-in Charge. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 25, 2026
11:30 IST
Tender Published
Tender notice published.
Completed
Aug 07, 2026
18:00 IST
Corrigendum-1 Issued
Clarifications on tender conditions and amendments issued.
Upcoming · 11 daysAug 07, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 11 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender