Tender For Repair Maintenance Of Ceiling Fans, Exhaust Fan, Wall Mounting Fan And Desert Coolers Under Of Ge (Army) No.1 Jodhpur
Tender Value
35 Lakhs
Estimated cost
Bid Submission
08 Aug 2026
7 days left
EMD
70000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jodhpur → Rajasthan
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repair Maintenance Of Ceiling Fans, Exhaust Fan, Wall Mounting Fan And Desert Coolers Under Of Ge (Army) No.1 Jodhpur
BOQ
| Sl. No. | Item Description |
| 1 | M&L for (in existing location and position) taking out and refixing after repairs, including rewinding of Desert Cooler fan motor of any make, 3 speed,1400 RPM of capacity 1/5 HP with super enameled copper winding wire of appropriate size (as per existing) incl Bush/Shaft/Ball bearing as per existing make/model, complete all as specified and directed. |
| 2 | S&F in replacement of oil filled capacitor 4.00 MFD for desert cooler fan motor, complete all as specified and directed. |
| 3 | M&L in replacement of bottom tank and top ( in existing location and position) of approx size - 750 X 750 X 200 mm ( as per existing ) for Desert Cooler made out of 18 gauge PGI sheet with and including two coats of synthetic enamel painting over one coat of red oxide primer on the new surfaces to match with existing surface outside and inside surface with approved quality paint including leakage testing, complete all as specified and directed. |
| 4 | M&L ( in existing location and position ) in replacement of front grill ( as per existing )( horizontal and vertical members moveable) of the Desert Cooler made out of 20 gauge PGI sheet with Name plate, complete all as specified and directed. |
| 5 | Supply and fix in relacement ( in existing location and position) three speed selector switch, complete all as specified and directed. |
| 6 | M&L in replacement of side supporting columns to be fabricated out of 18 gauge PGI sheet of size 80x80x800 mm with and including necessary nut, bolts etc., complete all as specified and directed. |
| 7 | M&L in replacement of side/rear panel made out of 20 gauge PGI Sheet with suitable handles with and including two coats of synthetic enamel paint over one coat of red oxide primer to match with the existing desert cooler, complete all as specified and directed. |
| 8 | M&L for painting to old steel surfaces of Desert cooler capacity up to 5000 Cft with one coat of synthetic enamel spray paint hammer tone paint of approved colour over one coat of red oxide primer on external surface and one coat of anti corrosive black paint inside the Body tank and side grills over a coat of red oxide primer complete including scraping/rubbing with wire brush on old surface of Desert cooler and writing of MES No etc complete at site or at E/M store yard all as specified and directed by Engineer-in-Charge . |
| 9 | M&L in replacement of Desert Cooler fan motor capacity 1/5 HP three speed, 1400 RPM single phase with aluminium fan blade, bracket supporting stand, complete all as specified and directed. |
| 10 | M&L in replacement of submersible pump of discharge head 2.5 Mtr 220-240 Volts AC Supply single phase 40 watt, complete all as specified and directed. |
| 11 | M&L in replacement of Wood wool pad for Desert Cooler of size 500 x 550 x30 mm (set of three pads) superior quality including binding properly with GI wire of 16 SWG complete all as directed by Engr-in-Charge . |
| 12 | Material and labour in replacement of MS weld wire mesh having apparture size 25 mm and fitted in side grills/rear complete all as directed by Engr-in-Charge. |
| 13 | M&L in replacement of Wood wool pad Heavy duty for Desert Cooler of suitable size (set of three pads) superior quality including binding properly with GI wire of 16 SWG with grill complete all as directed by Engr-in-Charge . |
| 14 | M&L in replacement of PVC insulated and PVC sheathed cable copper conductor 3 core 1.0 Sqmm cross sectional area superior quality complete all as directed by Engr-in-Charge. |
| 15 | Material and labour in replacement of PVC water distribution cup of one inlet and 3 outlets fixed with MS nuts and bolts complete (as per sample) all as directed by Engr-in-Charge . |
| 16 | M&L in replacement of PVC elbow suitable for desert cooler (as per sample) all as directed by Engr-in-Charge . |
| 17 | M&L in replacement of PVC pipe 15 mm dia heavy duty for Desert Cooler Pump complete all as directed by Engr-in-Charge . |
| 18 | M&L for painting to desert cooler stand with two coats of synthetic enameled paint of approved colour over a coat of red oxide primer including preparation of old surfaces complete all as specified and directed by Engineer-in Charge. |
| 19 | M&L in replacement of motor fixing ring (not less than 25 mm width ) for desert cooler eight screw / clip type(asper sample) complete all as directed by Engr-in-Charge . |
| 20 | M&L for taking down desert cooler installed at ground floor safely , including cleaning inside , outside , motor oilng sevicing and pump servicing including putting up in same location and position complete all as directed. NOTE: Replacement of any spare parts shall be measured and paid separately under respective item of schedule 'A'. |
| 21 | All as per item No. 20.00 here-in-above but desert cooler installed at first floor |
| 22 | All as per item No. 20.00 here-in-above but desert cooler installed at Second floor |
| 23 | M&L for framed brackets for cooler stand as shown in Drg No CEJZ/TD/72/2015 sheet1/1 of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc.. n exc 10 kg each brackets, conforming to Fe.290.Gde-E-165 (Brackets over 10 kg each to be measured under 'Structural Steel') and used for step/stairs, including M&L for steel rack bolt / fastner 100 mm long 12 mm dia - 4 Nos for fixing stand, complete all as specified and as directed |
| 24 | S&F in existing location and position PTMT stop cock 15 mm dia high pressure screwed for iron pipe, complete all as specified and as directed. |
| 25 | S&F in existing location and position PTMT Ball valves 15 mm dia high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe, complete all as specified and as directed. |
| 26 | M&L for wiring for circuit / sub main wiring alongwith earth wire with the following sizes of FR LSH PVC insulated , multistranded copper conductor cable ,( 2 X 1.5 Sq mm + 1X 1.5 Sqmm ), single core drawn in and including PVC casing capping 25 mm width , to be fixed on surface/ ceiling, complete all as specified and directed |
| 27 | S&F in replacement of 3 Pin Plug Top 06Amps ISI Marked 230 Volts, complete all as specified and directed. |
| 28 | M&L in replacement of PVC Connection pipe ISI Marked 300mm long heavy duty, complete all as specified and as directed. |
| 29 | M&L in replacement of PVC stop cock ISI Marked heavy duty, complete all as specified and as directed |
| 30 | S&F in replacement PVC moulded box of switch socket combination of cap - 6 Amp, complete all as specified and as directed. Please Enable Macros to View BoQ information |
| 31 | S&F in replacement PVC moulded box of switch socket combination of cap - 6 Amp, complete all as specified and as directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 18, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 08, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 7 daysAug 17, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 16 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender