Tender For Repair/ Maintenance To Iron Gate, Rolling Shutter, Aluminium Partition And Joinery Work In 512 Abws And Otm Accn In Zone B And C Area Under Age B/R-I Under Ge (Central) Khadki.
Tender Value
40 Lakhs
Estimated cost
Bid Submission
10 Aug 2026
20 days left
EMD
80000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Pune → Maharashtra
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repair/ Maintenance To Iron Gate, Rolling Shutter, Aluminium Partition And Joinery Work In 512 Abws And Otm Accn In Zone B And C Area Under Age B/R-I Under Ge (Central) Khadki.
BOQ
| Sl. No. | Item Description |
| 1 | Taking down cement plaster on brick wall, stone wall and concrete surfaces etc including raking out joints, hacking for key, scrubbing down with water at any heights by using necessary equipments complete all as specified and directed. |
| 2 | Material and labour for 15mm thick rendering on brick /concrete or dubbed surface in CM 1:3 with water proofing compound finishing even & fair without using extra cement complete all as specified and as directed. NOTE :- Liquid water proofing compound shall be measured & paid separetely |
| 3 | Material and labour for rendering/plastering 10 mm thick in cement mortar (1:6) on fair faces of brick wall or concrete surfaces finished even and smooth without using extra cement complete all as specified and as directed. |
| 4 | Material and labour for rendering 5 mm thick on concrete surfaces as in ceiling in CM 1:3, finished even and smooth without using extra cement complete all as specified and as directed. |
| 5 | Material and labour for preparation of new plastered wall surfaces of any description and applying two coats of cement base paint including Priming plastered and other surfaces with alkali resistant primer complete all as specified and as directed. NOTE :- (i) filling of cracks if any, holes and dents are includes in the same rates (ii) Proper curing with water to be done before and after application of 1st coat.(iii) height upto 4 Storey |
| 6 | Material and labour for preparation of new plastered surfaces of wall surfaces levelling/edging the disturbed places/edges using necessary filling compound of Birla/JK wall care putty to obtain smooth regular/even finish using sand paper and applying two coat of oil bound distemper upto height 10 mtr etc complete all as specified and as directed. |
| 7 | Material and labour for preparation of new plastered surfaces of ceiling, chhajjas, roof projection, facia, fins, parapet etc and applying three coats of white wash complete all as specified and as directed. |
| 8 | Material and labour for rendering 10mm thick on concrete surfaces/brick wall in cement mortar 1:3 finishing even and smooth without using extra cement with water profing compound to chhajjas, roof projection, facia, fins, parapet etc. and similar likes upto height 10 mtr including necessary scaffolding, ladder, formwork complete all as specified and as directed. NOTE :- Water proofing compound shall be measured & paid separetely |
| 9 | Supply only liquid water proofing compound complete all as specified and as directed. |
| 10 | Material and labour for complete removal of existing treatment on wall surfaces of any description plastered or unplastered surfaces of wall and applying two coats of cement base paint including Priming plastered and other surfaces with alkali resistant primer complete all as specified and as directed. NOTE :- (i) filling of cracks, holes and dents are includes in the same rates (ii) Proper curing with water to be done before and after application of 1st coat.(iii) height upto 04 storey |
| 11 | Material and labour for preparation of old plasterd or unplastered surfaces of ceiling and applying one coat of oil bound destemper complete all as specified and as directed. |
| 12 | Material and labour for complete removal of existing treatment on wall surfaces of any description plasterd or unplastered surfaces of wall and applying two coat of oil bound destemper, including thin layer of wall care putty, Priming plastered and other surfaces with alkali resistant primer complete all as specified and as directed |
| 13 | Material and labour for preparation of old painted wooden surfaces of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint any tint all as specified and as directed. |
| 14 | Material and labour for preparation of old painted steel surfaces of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint of any tint all as specified and as directed. |
| 15 | Material and labour for complete removal of existing treatment & washing rubbing down and stopping of distempered and painted surfaces incl preparation of old undecorated surface of walls for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces, complete all as specified and as directed |
| 16 | Demolition of Brickwork or stone/boulder masonry, built in cement/cement lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as directed. |
| 17 | Material and labour for Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, Modular bricks in cement mortar 1:4 complete all as specified and as directed. |
| 18 | Taking down chowkhat or frame n. exc 1.5 Sqm each but with shutter (without taking off shutter from the frame) complete all as specified and as directed. |
| 19 | Taking down chowkhat or frame exc. 1.5 Sqm but n. exc 4 Sqm each but with shutter (without taking off shutter from the frame) complete all as specified and as directed. |
| 20 | Taking down shutter of any description exceeding 1 Sqm but n. exc 2 Sqm each complete all as specified and as directed. |
| 21 | Taking down shutter of any description but exceeding 2 Sqm each complete all as specified and as directed. |
| 22 | Supply and fix pressed steel frames of size 105x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, tarring back of chowkhats & holdfast etc, complete all as specified and as directed. |
| 23 | Supply and fix pressed steel frames of size 125x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, tarring back of chowkhats & holdfast etc, complete all as specified and as directed. |
| 24 | Supply and fix 2nd class HW plain solid straight chowkhats/frame wrought framed rebated on the solid, rounded or chamfered put together with glue pinned at joints complete all as specified and directed |
| 25 | Material and labour for providing cement concrete type B-1 (1:2:4) (using 20mm graded aggregate) as in pressed steel door frame (backfill), complete all as specified and as directed. |
| 26 | Supply and fix factory made solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. square tube etc complete all as specified and as directed. |
| 27 | Supply and fix factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame etc complete all as specified and as directed. |
| 28 | Supply and fix for 35mm thick 2nd class hard wood factory maid plain, framed paneled shutter (two panel) with lock rail and panel of 9mm BWP commercial ply or 12mm venered partical board with commercial veneering on both side faces. The size of rail and stile as per ISI 1003 (Part-I), kiln seasoned and chemically pressure treated (factory made shutter) complete all as specified and as directed. |
| 29 | Supply and fix for 30mm thick flush shutter, solid core construction, with block board core plywood face panels, commercial type on both sides, chemically treated against termite infestation, complete all as specified and as directed. |
| 30 | Supply and fix 30 mm thick 2nd class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) supplied and fitted to chowkats as specified in SSR-I, complete all as specified and as directed. |
| 31 | Material and labour for 18/19mm thick Prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work including external teak wood lipping, 6mm thick fixed with nails around the partical board etc in repair complete all as specified and as directed. |
| 32 | Supply and fix in repair Steel rolling shutters, 1mm thick, with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete: push pull or manual type with bevel gear box and crank handle type, including dismantling,Thickness of laths in mm 1.0, complete all as specified and directed. |
| 33 | Supply and fix in repair Steel rolling shutters, with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete: gear operated type with bevel gear box and crank handle type, including dismantling,Thickness of laths in mm 1.0, complete all as specified and directed. |
| 34 | Supply and fix for aluminum alloy powder coated door shutters partly panelled partly glazed shutter having door frame made out of alumunium anodised section of size 100 x 44.45 x 2.00 mm thick and shutters made out of bottom rail of tube section 114 x 44.45 x 2.00 mm thick and top rail, middle rail, styles of tube section 85 x 44.45 x 2.00mm thick, using 5 mm thick tinted glass of selected quality of required size fixed with rubber beading, aluminium clip, glazing plate and 6-8 mm dia anchor rod and 12 mmm thick both side prelaminated particle board including fixed aluminium anodised 2 nos 125 mm circular handle, 200 mm long tower bolts -2 Nos, Door Stopper 2 Nos, One No lock 4 lever (ISI), vertical type of 65 mm with triplicate key, bush and including 3 Nos aluminium butt hinges, double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, making good of wall surface to match with existing surface complete door frame fixed to wall with 8 Nos rawl plugs 150mm, complete all as specified and as directed.NOTE :- Particle board and glass is included in this item and no extra payment shall be made for the same. |
| 35 | Supply and fix aluminium powder coated window sliding type (3 track) with frame size 100x35x1.2mm thick and shutter frame size 39.40x17.70x1.2mm thick with and including two glass shutter and one mesh shutter including necessary jointing cleats, glazing clips, rubber packing, powder coated aluminium snap beading screws with and including 4mm thick tinted float glass and 0.36mm dia apperture 1.4mm SS wire mesh and fittings etc, complete all as specified and as directed. |
| 36 | Supply and fix aluminium louvered ventilators of section size 80mm x 20mm x 1.50mm including 5mm thick frosted glass fixed in half portion and adjustable type louvers in another half and stainless steel wire mesh fixed type on out side frame etc. complete all as specified and as directed. |
| 37 | Material and labour for preparation of New wooden surfaces of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint any tint over pink primer all as specified and as directed. |
| 38 | Material and labour for preparation of New steel surfaces of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint of any tint over primer red oxide, zinc crome all as specified and as directed. |
| 39 | Supply and fix butt hinges, 100mm long, extruded aluminium alloy with galvanised mild steel hinge pin, complete all as specified and as directed. |
| 40 | Supply and fix 140mm size floor door stopper of aluminium alloy body and tongue with hard drawn steel spring, fixed in floor for aluminium/wooden door, complete all as specified and as directed. |
| 41 | Supply and fix aluminium alloy, anodised, sliding door bolt 250mm long, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy 12mm dia, complete all as specified and as directed. |
| 42 | Supply and fix 300mm long mild steel ordinary rat tail rod pattern springs, including roller and roller plate complete all as specified and as directed. |
| 43 | Supply and fix extruded aluminium alloy handles, fabricated type, anodised of size 150 mm complete all as specified and as directed. |
| 44 | Supply and fix, aluminium anodised, barrel tower bolts of extruded section with length of bolt 200 mm and fixed complete all as specified and directed |
| 45 | Supply and fix in repair Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples etc complete all as specified and as directed. |
| 46 | Hacking out old broken glass (any thickness, size, quality or description) from wooden/steel frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads, complete all as specified and as directed. |
| 47 | Supply and fix plain sheet glass 4mm thick, ordinary quality, not exc 0.50 Sqm in each pane fixed to aluminium door/window and steel window/frame with oil putty and securing pins, spring clips etc complete all as specified and as directed. |
| 48 | Supply and fix in repairs for Harrison rails mild steeel , chromium plated with fixing brackets stops rollers (both side) etc, complete all as specified and as directed. |
| 49 | Supply and fix in repair Aluminium (Die cast) door closure hydrauically regulated, designation, No-2, universal type suitable for door shutter of 701 to 850mm in width and of weight between 36 to 60Kg and fixed, complete all as specified and as directed. |
| 50 | Supply and fix in repair double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and as directed. |
| 51 | Supply and fix in repair brass mortice lock vertical type 100mm size, 4 lever fixed in aluminium shutter, complete all as specified and as directed. |
| 52 | Supply and fix in repairs Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed bore dia pipe in 15mm complete all as specified and as directed. |
| 53 | Supply and fix in repairs ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed bore dia pipe in 20mm complete all as specified and as directed. |
| 54 | Supply and fix in repairs 20mm dia gun metal,globe or gate valve with iron wheel head screwed both ends for iron pipe and fixed complete all as specified and directed. |
| 55 | Material and labour for disconnecting of existing PVC tank of capacity exc 250 Ltr & n. exc 500 Ltrs for cleaning including setting aside temporarily and refixing later in same position for water supply to enable water proofing treatement of roof slab beneath the tank in following laid down process all as specifed and directed. (a) Dewatering & removing all settled silt,scale & dust from inside from tanks using coconut brush manually and applying bleaching powder and allowed to rest 1 hour. (b) Cleaning & rinsing the tank using fresh water to wash out complete and allowed to dry for 30 mins. (c) Writing letters of 7 cm height using synthetic enamel paint (white colour) to mention date of cleaning incl rubbing out old letters written over the tank. (d) Re-fixing the tank with fitting as required in same position or raised/lower height after cleaning of water (as may necessary) complete all as specified and as directed. |
| 56 | Material and labour for disconnecting of existing PVC tank of capacity exc 500 Ltr & n. exc 1000 Ltrs for cleaning including setting aside temporarily and refixing later in same position for water supply to enable water proofing treatement of roof slab beneath the tank in following laid down process all as specifed and directed. (a) Dewatering & removing all settled silt,scale & dust from inside from tanks using coconut brush manually and applying bleaching powder and allowed to rest 1 hour. (b) Cleaning & rinsing the tank using fresh water to wash out complete and allowed to dry for 30 mins. (c) Writing letters of 7 cm height using synthetic enamel paint (white colour) to mention date of cleaning incl rubbing out old letters written over the tank. (d) Re-fixing the tank with fitting as required in same position or raised/lower height after cleaning of water (as may necessary) complete all as specified and as directed. |
| 57 | Removing old tar felt, all loose dirt,old roof tiles,including taking down cement plaster cleaning the concrete surface including removal & cleaning of vegetation, fungus,moss small trees etc from the roof top with wire brush, removing the strips of lightening conductor including refixing the same after repair work and applying neat cement slurry @ 1.5Kg/Sqm complete all as specified and as directed. |
| 58 | Material and labour for rendering 10 mm thick on existing concrete surfaces of roof in CM (1:4) mixed with water proofing compound @ 3% by weight of cement, finishing even and smooth without using extra cement with and including water proofing treatment over RCC slab, complete all as specified and as directed.NOTE :- Water proofing compound paid separately |
| 59 | Material and labour for applying oil bound bitumen primer @ 0.3 kg/Sqm,over RCC slab, and providing and laying APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application complete all as specified and applying two coat of solar reflective aluminium paint on membrane surfaces @ 100ml/Sqm complete all as specified and as directed . |
| 60 | Dismantaling floor hearth or wall tiling/china moisac including cement mortar bedding (but not backing ) , removing serviceable tiles to store and rubbish off the premises, including removal debris material out of defence land complete all as specified and as directed. |
| 61 | Material and labour vetrified ceremic tiles 10 mm thick, in LIGHT SHADE, (Square/rectangular) polished, area of each tile not exceeding 0.36 sqm, in floors etc. set & jointed in neat cement slurry and pointed in coloured cement to match coloured tiles laid over and including 15 mm thick screed bed or bedding layer in CM (1:6) complete all as specfied and as directed. |
| 62 | Material and labour for vitriefied ceramic tiles 10mm thick LIGHT SHADE(square/rectangular) polished area of each tiles not exceeding 0.36 sqm as in vertical surfaces such as dados/skirting etc set and jointed in neat cement slury and in coloured cement to match Coloured on incl plaster (backing coat) 1:4 CM 10mm thick complete all as specified and as directed. |
| 63 | Material and labour for glazed ceramic coloured tiles of size 450 x 300 x 6 to 7 mm,450x350 or 350x250, 300x600mm 6 to 7mm thick on vertical surface such as skirting/dado etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tile with & including rendering 10 mm thick cement plaster in cement mortar 1:4 finished rough to fix tiles complete all as specified and as directed. |
| 64 | Material and labour non skid coloured ceramic tiles 7 to 8mm thick square/ rectangular area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm as in floor etc set and jointed in neat cement slurry and pointed in white cement with pigment to match, laid over and including 15mm thick cement screed bed in cement mortar 1:6 complete all as specified and as directed. |
| 65 | Demolition of cement concrete in ground floor and paving not exc 15cm thickness (below or above ground level) complete all as specified and as directed. |
| 66 | Material and labour 75 mm thick PCC 1:3:6 type C-2 using 40mm graded aggregate as in plinth protection finishing even & fair without using extra cement laid in bays with construction, 6mm thick joints should be filled with bitumen mastic filling comprising of one part of heated bitumen 80/100 gde and three part of sand ( all by weight) complete all as specified and as directed. |
| 67 | Material and labour 25mm thick PCC 1:4:8 type D2 (using 40mm graded stone aggregate) as in sub base complete all as specified and as directed. |
| 68 | Demolition of stone slabs and tiles of any description or thickness in floors aprons etc laid dry or laid dry and pointed all as specified and as directed. |
| 69 | Material and labour for Granite 20mm thick work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms, vertical surface of wall and like laid over and including 12mm thick screed bed or bedding layer cement mortar (1:3) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including dismantling and removing the debris outside the defence land complete all as specified and as directed. |
| 70 | Material and labour for rounding to edges of granite stone slabs one edge such as in counter type WHB platform etc. to the entire satsfaction of Engineer-in-Charge, complete all as specified and as directed. |
| 71 | Supply and fix in repairs 15mm bore tubes, 'medium grade' galvanised, with all fitting and fixed complete to wall and ceiling or laid in floors including necessary cutting chasing into wall/concealed including taking down old steel tubing etc complete all as specified and as directed. |
| 72 | Supply and fix in repairs 20mm bore tubes, 'medium grade' galvanised, with all fitting and fixed complete to wall and ceiling or laid in floors including necessary cutting chasing into wall/concealed including taking down old steel tubing etc complete all as specified and as directed. |
| 73 | Supply and fix in repair for vitreous china squatting pan, orissa pattern, size 580 x 440mm white, with integral foot rests (excluding flushing cistern and flush pipe) including 'P' or 'S' trap & PVC flushing bend fixed complete all as specified and as directed. |
| 74 | Supply and fix in repairs for vitreous china wash down water closet pan, pedestal pattern, white, including PVC flush pipe fixed complete including connection to existing cistern complete all as specified and as directed. |
| 75 | Supply and fix in repairs for plastic water closet seat white closed pattern with flat bottom and cover and mild steel chromium plated hinging device any type (as per site requirement any type any size), ISI marked fixed complete all as specified and as directed. |
| 76 | Supply and fix in repairs for vitreous china wash basin, white, flat back size 550x400 excluding taps, waste chain and plug and porecelain stopper but including bracket any size and waste coupling of PTMT, including cutting for and pinning in ends of bracket or erecting stand execlusive of fixing of supply and waste pipe etc fixed complete all as specified and as directed. |
| 77 | Supply and fix in repair Sinks with drainage board made of stainless steel 1mm thick, kitchen or laboratory with plugs, washers and waste ; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x355mm x165mm complete all as specified and as directed. |
| 78 | Supply and fix in repair Rotational moulded polythylene water storage tanks 1000 liters capacity (three layered), ISI marked cylindrical vertical with closed top including 3 Nos GI check nuts and tank nipple of 20mm bore for inlet and outlet, 20mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball hoisted and fixed in position all as specifed in SSR Part I complete all as specified and as directed. |
| 79 | Supply and fix in repair rotational moulded polythylene water storage tanks 500 liters capacity (three layered), ISI marked cylindrical vertical with closed top including 3 Nos GI check nuts and tank nipple of 20mm bore for inlet and outlet, 20mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball hoisted and fixed in position all as specifed in SSR Part I complete all as specified and as directed. |
| 80 | Supply and fix in repairs for PVC waste pipe 32mm dia, complete with 80cm long flexible for WHB/Urinals fixed all as specified and as directed. |
| 81 | Supply and fix in repair PVC connection 600 mm long, 15mm size with PTMT nuts complete all as specified and as directed. |
| 82 | Supply and fix in repairs bib tap, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed 15mm bore complete all as specified and as directed. |
| 83 | Supply and fix in repair Health faucet (ABS body) mild steel chromium plated suitable for 15mm dia pipe with 1.25 mtr long flexible tube and ABS wall hook including making connection and fixed in position complete all as specified and as directed. |
| 84 | Supply and fix in repairs 15 mm bore bib tap 2 In 1 cast copper alloy, chromium plated, long body fancy type with capstan headed, screwed down, screwed for iron pipe complete all as specified and directed. |
| 85 | Supply and fix in repairs for fancy pillar taps, chromium plated, screwed down high pressure, with or without lettered Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe and fixed for 15mm bore etc complete all as specified and as directed. |
| 86 | Supply and fix in repairs stop valve / angle valve fancy type cast copper alloy chromium plated screwed down high pressure with capstan heads screwed both ends for iron pipe or for union and fixed 15mm bore complete all as specified and as directed. |
| 87 | Supply and fix in repairs 10 ltr PVC valve less symphonic action type flushing cistern, low level white with inlet ball valve float and handle with flush pipe complete all as specified and as directed. |
| 88 | Taking down eaves gutters and rainwater pipes (any size or pattern ), including all fittings, heads, shoes, bends, swan necks etc. including cleaning or refixing or removal to store complete all as specified and as directed. |
| 89 | Supply and fix 110 mm dia PVC (SWR ) pipes Single socketed in any length with rubber rings ljoits fixed to walls complete all as specified and as directed. |
| 90 | Supply and fix PVC (SWR) pipes 75mm bore single socketed in any length with rubber ring joints laid in floors, trenches complete all as specified and as directed. |
| 91 | Supply and fix 110 mm dia PVC (SWR ) branches piece, double (double Y) equal or unequal with access doorrubber rings joints fixed to walls complete all as specified and as directed. |
| 92 | Supply and fix PVC (SWR) branch pieces, single (equal or un equal), ordinary or inverted (spigot or socket type) or with parralled branches of 110 mm dia with access door complete all as specified and directed. |
| 93 | Supply and fix 110 mm dia PVC (SWR ) bends any radius with access door complete all as specified and as directed. |
| 94 | Supply and fix 75 mm dia PVC (SWR ) bends any radius with access door complete all as specified and as directed. |
| 95 | Material and labour for 100mm dia cast iron floor trap plain with grating including jointing and fixed with cement concrete type B-1 (1:2:4) complete all as specified and as directed. |
| 96 | Supply and fix for PVC floor trap 75mm complete all as specified and as directed. |
| 97 | Dismantling wroght iron or mild steel work of any description not oterwise provide for complete all as specified and directed |
| 98 | Supply and fix framed work as in doors or gates of angle or other section with gusset plates, rails, braces etc complete drilled for fixing of steel gate sheeting or other covering, doors, etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, runing rails and guides ) and hanging also fastning and fixing complete all as specified and as directed. confirming to FE-290 ( Gde E-165). |
| 99 | Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets including E- Grid frame work complete all as specified and as directed. |
| 100 | Supply and fix in repair E-board 'Everest' make 600x600x4mm thick white prelaminated sett embosed reinforced designed ceiling board tiles of approved texture at any height laid on Hot dipped Galvanised iron imposed grid with 24mm wide T-section exposed flanges which shall be powder coated white. The frame work shall comprise of main runner made from 0.33mm thick GS sheet and of size 24x32x3000mm and spaced at 1200mm centers securely fixed to the structural soffits by approved hangers at 1200mm maximum centers. Hangers of GI wire 2mm dia to be fixed by approved rawl plug, level adjusters and screws etc. The last hanger at the end of each main runner shall not be greater than 450mm from adjacent wall. Flush fitting of 1200mm long cross tee (with double stitching) to be interlocked between main runners at 600mm center to form 1200x600mm modules cross tee longer than 600mm to be supported independently. 600x600mm modules to be formed by fitting 600mm long cross Tee centrally between the 1200mm cross tee. Tee, Perimeter wall angle shall be of 0.45mm thick GS sheet of size 19x19mm and 300mm long of white colour all as per manufacture instruction, including taking down wall/ceiling boards(fibre, pulp insulation etc) or inslutation boards any thickness incl fillets complete all as directed. |
| 101 | Supply and fix in repairs 5mm thick PVC sheet fillet of width 35mm for wall panelling inclusive of fixing on to wall to make PVC Frame as per specification and drawing complete all as specified and as directed. |
| 102 | Supply and fix in repair solid PVC wall lining consisting of 5mm thick Plain colour PVC sheet and single side prelam PVC sheet used inclusive of solvent cement and fixing at site on PVC frame including 5mm thick sheet fillet of width 35mm as per specifications and drawing, complete all as specified and as directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 18, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 10, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 20 daysAug 12, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 22 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender