Tender For Repair & Rewinding Of Submersible Pump Set And Monoblock Centrifugal Motor Pump Sets Under Sub Div Dausa City
Tender Value
4 Lakhs
Estimated cost
Bid Submission
27 Jul 2026
6 days left
EMD
8000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Dausa → Rajasthan
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repair & Rewinding Of Submersible Pump Set And Monoblock Centrifugal Motor Pump Sets Under Sub Div Dausa City
BOQ
| Sl. No. | Item Description |
| 1 | Repair Rewinding of Submersible motor includes full servicing and rewinding (wherever required) as per manufacturer's specification and to the satisfaction of Engineer Incharge. It includes the replacement of minor parts such as bushes (oil seal bush) Nut Bolts, washers, cable seal, gland ring, vent plug, water drain plug, etc. complete job |
| 2 | Above 5HP to 7.5 HP V-6 |
| 3 | Above 7-5 HP to 10 HP V-6 |
| 4 | Motor opening cable jointing & refitting charges when rewinding is not required. V-6 |
| 5 | Providing & Replacement of G.M./S.S. Bushes for all types of motors (per set of 4Nos.) including cost of sleeves V-6 |
| 6 | Providing & Replacement of thrust bearing for all types of motor. It includes cost of all components connected with thrust bearing. V-6 |
| 7 | Replacement of thrust plate for all types of motors V-6 |
| 8 | PART (B): SCHEDULE OF SPARES & REPAIR OF SUBMERSIBLE PUMP : |
| 9 | Supply and fixing spare parts for repair of pump set including cost of opening refitting, servicing, and machining, if required. It also includes the cost of nut bolt, studs, washer packing, keys etc. complete. |
| 10 | Providing & fixing of GM neck rings parts on impeller. |
| 11 | Plain Type V-6 |
| 12 | Providing & Fixing of GM/SS bush per piece |
| 13 | Plain Type V-6 |
| 14 | Providing & replacement of Nylon Impeller |
| 15 | Plain Type V-6 |
| 16 | Pump opening & fixing including machining & all finishing work for desired performance |
| 17 | Plain Type V-6 |
| 18 | Monoblock Pump Set |
| 19 | Rewinding of three phase squirrel cage induction motor of HSC pump sets including all necessary material and of the same characteristics as original with required size of super enamelled copper wire (excluding cost of copper wire) 'E' class insulation material and testing of motor on no load but to be guaranteed against testing on load at site, including making electric connection at site of installation of motor with starter, alignment with pump sets and transportation to and fro from installation site complete as per direction of engineer in charge at site. |
| 20 | Above 45.00 HP but upto 50.00 HP |
| 21 | SUPPLY & FIXING OF SPARE PARTS HSC PUMP SETS (MOTOR + PUMP) |
| 22 | Connection Plates |
| 23 | 30 HP to 50 HP |
| 24 | G.M./SS Gland Guide Bush |
| 25 | 30 HP to 50 HP |
| 26 | Shaft with Sleeve Chuck Nut |
| 27 | 30 HP to 50 HP |
| 28 | JOB WORK FOR REPAIR OF PUMP MOTOR |
| 29 | Bearing Housing (rebuilding, turning & finishing) |
| 30 | 30 HP to 50 HP |
| 31 | Bearing Cap (rebuilding, turning & finishing) |
| 32 | 30 HP to 50 HP |
| 33 | Impeller Reconditioning for all type of Pump |
| 34 | 30 HP to 50 HP |
| 35 | Coupling with stud and rubber bush |
| 36 | 30 HP to 50 HP |
| 37 | Supply & Fixing of tyre coupling sets according to relevant IS code in Centrifugal couple pump sets of approved make Unit. This job also included re-alignment of centrifugal couple pump set after fixing of tyre coupling set as per directed by Engineer-in charge.Type 16 Nos. set |
| 38 | Supplying of super enamal copper wire suitable for rewinding of induction motor (only procured for motor rewinding) |
| 39 | Routine maintenance of centrifugal coupled pump and motor including opening, cleaning, greasing and refitting / changing of ball bearing if required, gland refilling and replacing all rusted studs, replacing rubber bushes & coupling nut & bolts for coupling pulley, tightening all nut & bolts of foundation, baseplate, pump & motor etc. Checking & correcting alignment of pump & motor including necessary materials i.e. grease, nut & bolts, studs, washers, gland packing and rubber bushes etc. work done at site complete job |
| 40 | Above 30 HP and up to 50 HP Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 20, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 27, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 6 daysJul 28, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 7 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender