Tender For special Repair To Bldg No T-618, T-677 And Allied Wks Near Mt Park (Guest Toom) And Certain Revenue And Minor Work At Cijw School Vairengte Mil Stn
Tender Value
45.10 Lakhs
Estimated cost
Bid Submission
10 Aug 2026
10 days left
EMD
90200
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Kolasib → Mizoram
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for special Repair To Bldg No T-618, T-677 And Allied Wks Near Mt Park (Guest Toom) And Certain Revenue And Minor Work At Cijw School Vairengte Mil Stn
BOQ
| Sl. No. | Item Description |
| 1 | B & R Division Items |
| 2 | Demolition of un-reinforced cement concrete in ground floor and paving not exceeding 15 cm thick (below or above ground level) complete all as specified and directed. |
| 3 | Demolition of reinforced cement concrete in roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work complete all as specified and directed. |
| 4 | Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, pillars etc. complete all as specified and as directed. |
| 5 | Dismantling floor, hearth or wall tilling including cement mortar bedding (but not backing) removing serviceable tiles to stores and rubbish off the premises. |
| 6 | Demolition of reed lathing, single or double including battens and plaster or chiken wire lathing all as specified. |
| 7 | Dismantling plain or corrugated steel sheeting, any gauge or any thickness as in roof covering, wall cladding, etc.including all necessary staging / scaffolding, etc. as required complete all as specified and as directed. |
| 8 | Dismantling of timber scantling 40 Sqcm and over in section, in any position in unframed work complete all as specified and directed. |
| 9 | Dismantling wall and ceiling boards (fibre, pulb, insulation etc) or insulation boards slabs/blankets any thickness including cover fillets all as specified and as directed. |
| 10 | Dismantling boarding any description fixed in any position with nails all as specified. |
| 11 | Dismantling SGW/asbestos cement/PVC pipe 50/75/100 mm dia including clamps complete all as specified and directed. |
| 12 | Dismantling of 75mm bore cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches, if required complete all as specified and directed. |
| 13 | Taking down chowkhats or frame with shutters (without taking off shutters from frame) each not exceeding 1.50 Sqm each complete all as specified. |
| 14 | Taking down Chowkhats or frames with shutters exceeding 1.5 Sqm but not exceeding 4 Sqm each (without taking off shutters from the frame) complete all as specified. |
| 15 | Taking up or down 15mm bore GI steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed. |
| 16 | Taking up or down 20mm bore GI steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed. |
| 17 | Excavating in trenches, n exc 1.50 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out soft/ loose type of soil complete all as specified and directed. |
| 18 | Returning, filling in trenches including spreading, leveling watering and ramming in layers not exceeding 25cm all as specified. |
| 19 | Removing of surplus soil not exceeding 50 m and deposited where directed at a level not exceeding 1.50m above the starting point all as specified. |
| 20 | Excavating in post holes (or similar holes) each n exc 0.50cum getting out returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, as insoft/ loose type of soil complete all as specified and directed. |
| 21 | M & L for PCC (1:4:8), Type D2 using 40 mm graded stone aggregate as in foundations, sub-base,filling and mass concrete complete all as specified. |
| 22 | M & L for 75mm thick cement concrete 1:3:6 type C2 (using 40mm graded stone aggregate) as in plinth protection finished even and fair without using extra cement laid in panels and joints filled with bituminous mastic filling with 1 part of bitumen and 3 part of sand complete all as specified and directed. |
| 23 | M & L for 75mm thick cement concrete 1:3:6 type C1 (using 20mm graded stone aggregate) as in sub base to floors/path and pavement complete all as specified and directed. |
| 24 | M & L Plain Cement concrete (1:3:6), type C-0 using 12.5mm graded stone aggregate as in filling of hallow steel chowkhats, bed block, fixing of holdfast and similar likes including necessary formwork complete all as specified. |
| 25 | Use and waste formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter rough finished flat surfaces of concrete complete all as specified and as directed. |
| 26 | Use and waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions for rough finished flat surfaces of concrete all as specified and directed. |
| 27 | Use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed |
| 28 | Use and waste Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide all as specified and directed. |
| 29 | M & L for Reinforced Cement Concrete M-25 (design mix) using 20 mm graded aggregate as in foundation including rafts, footings, foundation beams, plinth beams, bases for columns etc complete all as specified and directed. |
| 30 | M & L for Reinforced Cement Concrete M-25 (design mix) using 20 mm graded aggregate as in column, pillars, piers, posts, and struts complete all as specified and directed. |
| 31 | M & L for Reinforced Cement Concrete M-25 (design mix) using 20 mm graded aggregate as in beams, cantilever, lintels over 1.5m complete all as specified and directed. |
| 32 | M & L for Reinforced Cement Concrete M-25 (design mix) using 20 mm graded aggregate as in slab supported on walls, beams and columns in floors, roof landig balconies, canopies, deck slab and shelves and like complete all as specified and directed. |
| 33 | M & L for Reinforced Cement Concrete M-25 (design mix) using 20 mm graded aggregate as in cill band and similar items like complete all as specified and directed. |
| 34 | M & L for Mild Steel TMT Bar 10mm dia and over, cut to length bend to shape as required including cranking, hooking etc and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed. |
| 35 | M & L for Mild Steel TMT Bar 6mm to 8mm dia and over, cut to length bend to shape as required including cranking, hooking etc and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed. |
| 36 | M & L for Mild Steel TMT Bar 6mm dia and over up to 10 mm dia as in stirrups, spacers and binders as required including cranking, hooking etc and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed |
| 37 | M & L for brickwork with subclass 'B' or locally available best quality old size bricks, straight or curved on plan exc 6 m mean raduis, built in CM (1:6) complete all as specified and directed. |
| 38 | M & L for brick work in cement mortar (1:4) straight or curved on plan to any radius with locally available Subclass ‘B’ old size best quality bricks in half brick thick wall complete all as specified . |
| 39 | M & L for 15 mm thick rendering in cement mortar 1:6 on fair faces of brick wall or concrete surfaces, finished the surfaces even and fair without using extra cement complete all as specified. |
| 40 | M & L for 15 mm thick rendering in cement mortar 1:4 on fair faces of brick wall or concrete surfaces, finished the surfaces even and fair without using extra cement complete all as specified. |
| 41 | M & L for 10 mm thick rendering cement mortar 1:4 on fair faces of brick on vertical surface of walls to receive wall tiles complete all as specified. |
| 42 | Supply only integral water proffing compound complete all as specified. |
| 43 | M & L light vitrified ceramic tiles coloured 7 to 8mm thick (square/ rectangular) area of each tile not exceeding 0.36 sqm, as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile over including 15 mm thick screed bed or bedding layers in cement mortar 1:6 for tile over brushing with neat cement slurry as specified |
| 44 | M & L light vitrified ceramic tiles coloured ceramic tiles 8 to 10 mm thick ( square/rectangular) area of each tiles exc 0.18 sqm but not exc 0.36 sqm as in vertical surfaces of skirting/bdado etc over 10 mm thick rendering in cm (1:4) as backing coat for tile complete all as specified. |
| 45 | M & L Non Skid ceramic tiles colour 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.06 but not exceeding 0.11 sqm, as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including 15 mm thick screed bed or bedding layers in cement mortar 1:6 over brushing with neat cement slurry complete all as specified. |
| 46 | M & L for Glazed ceramic tiles in vertical surface size 450mm x 300mm x & ( 6mm to 7mm )mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match all as specified and directed. |
| 47 | M & L for 18-20mm thick granite stone slab, of any type, table rubbed and polished, in steps, jambs, pillars, window cills, cooking platforms and the like in laid over and including 20mm thick screed in cement mortar (1:6) with cement slurry @4 kg/Sqm including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of slab and taking off old damaged slab and disposing off complete all as specified and as directed. |
| 48 | S & F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified. |
| 49 | S & F pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified. |
| 50 | S & F Framed work such as grills, gratings, etc.. with ends of bars or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed. |
| 51 | S & F Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers,hold fasts, bands, straps, wall ties, plain angle cleats, eaves board frame and similar articles conforming to Fe-290 Gde-E-165 complete all as specified and directed. |
| 52 | S & F mild steel Plates plain cut to required size, forming holes to receive holding down bolt and welded to tubular/square hollow section truss at both ends complete all as specified. |
| 53 | S & F structural steel work in tubular/hollow sections trusses , Purlin , posts, rafter etc including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St.-240 complete all as as specified and directed. |
| 54 | S & F Solid PVC door frame of size 50mm x 47mm made of 5 mm plain colour PVC sheet reinforced with mild steel square tube , supplying & fixing in opening as per specification & drawing complete all as specified . |
| 55 | S & F Solid PVC double door frame of size 50mm x 95mm made of 5 mm single sidev plain colour PVC sheet reinforced with mild steel square tube , supplying & fixing in opening as per specification & drawing complete all as specified . |
| 56 | S & F Solid PVC door frame of size 50mm x 47mm made of 5 mm single side PVC sheet reinforced with mild steel square tube , supplying & fixing in opening as per specification & drawing complete all as specified . |
| 57 | S & F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, supply and fixing in the frame at site as per clause 8 B.2.1 of MES schedule Part-II (2004) complete all as specified. Make: Rajshri or equivalent as approved. |
| 58 | S & F Factory made wire gauzed PVC moulded door shutter 30 mm thick (style) wire gauzed i.e. panel will be of wire gauze in lieu of wood grain printed PVC sheet panel. The wire gauze shall be wrapped on an additional square 8mm M.S. Solid tube and this tube shall be welded to M.S. tubes. The wire gauge shall be stretched to tighten firmly consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded wood grain printed PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and wood grain printed PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of wood grain printed PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing. |
| 59 | S & F Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick prelaminated Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified. |
| 60 | S & F GI wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.18mm and fixed with wooden beeds complete all as specified and directed. |
| 61 | S & F 3 ways sliding anodized aluminium glazed window shutter with frame with the following specification all as specified & directed.(a) Window frame 3 track of size 95mm × 25mm × 1.5mm thick.(b) Stiles and rails of size 35mm × 25mm × 1.5mm.(c) 35mm × 35mm × 1.5mm T section mullion.(d) PVC gasket with 4mm thick tinted glass, incl. aluminium handles with necessary locking arrangement for 02 Nos glazed shutter.(e) Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm, fixed with stainless steel wire staples, incl. aluminium handles with necessary locking arrangement for 01 No gauzed shutter.Note: Measurement to be taken as overall width and height of window. No shutter or frame to be measured separately. All necessary accessories including tinted glass and stainless steel wire cloth required for assembling and fixing window at proper place complete are deemed to be inclusive. |
| 62 | S & F 2 way sliding anodized aluminium glazed ventilator shutter with frame consists of following specification all as specified & directed.(a) Ventilator frame 2 track of size 60mm × 25mm × 1.5mm thick.(b) Stiles and rails of size 35mm × 25mm × 1.5mm.(c) 35mm × 35mm × 1.5mm T section mullion.(d) PVC gasket with 4mm thick tinted glass, incl. aluminium handles with necessary locking arrangement.Note: Measurement to be taken as overall width and height of ventilator. No shutter or frame to be measured separately. All necessary accessories including tinted glass required for assembling and fixing window at proper place complete are deemed to be inclusive. |
| 63 | S & F 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixedcomplete all as specified. |
| 64 | S & F 100mm long MS Butt hinges, medium weight, cold rolled complete all as specified. |
| 65 | S & F 150 mm long aluminium handles cast type anodised complete all as specified & directed . |
| 66 | S & F 200mm long aluminium, anodised, Barrel tower bolts of extruded section complete all as specified & directed . |
| 67 | S & F as in repairs MS chromium plated curtain rods with brackets including fixing stops, rollers bracket etc with harrison rails all as specified and directed . |
| 68 | S & F as in repair, vitreous china wash basin, white flat back size 550 x 400 mm, excluding taps, waste chain, plug and porcelain stopper but including waste coupling, brackets, cutting for and pinning in ends of bracket or erecting stand complete all as specified. |
| 69 | S & F in repairs Vitreous china wash down water closet pan ( pedestal pattern ) , white including connection to drain ( or outgoing pipe ) and to flush pipe, antishonage pipe and plastic water closet seat, black closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device etc complete all as specified and as directed. |
| 70 | S & F in repair PVC valveless, syphonic action type, low level flushing cistren 10 ltr capacity light coloured with inlet ball valve float and handle including flush / discharge pipe complete all as specified. |
| 71 | S & F in repair soap dish chromium plated standerd quality fixed on wall with brass screw complete all as specified. |
| 72 | S & F in repair PVC connections 15mm size with PTMT nuts of length 450 m complete all as specified. |
| 73 | S & F as 15 mm bore bib taps fancy type, chromium plated, cast copper alloy with crutch or butter fly handle, screwed down, screwed for iron pipe or for brass ferrule complete all specified and directed. |
| 74 | S & F in repair 15mm bore pillar tap cast copper alloy with capstan head, chromium plated concealed screwed down high pressure with or without hot or cold with long shunk screwed shanks and fly nuts screwed for iron pipes and connecting to water pipe line complete all specified and directed. |
| 75 | S & F 15mm bore angular stop cock, cast copper alloy cromium plated fancy type screwed for 15 mm bore GI pipe or for unions complete all specified and directed. |
| 76 | S & F as in repair 15mm bore stop valves/angle valve of cast copper alloy, concealed, cup screwed down, high pressure with crutch or butter fly handle, chromium plated, with long shank fixed complete all as specified. |
| 77 | S & F in repairs Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified |
| 78 | S & F Chromium plated shower roses with swivel joints and wall bracked, any size including fixing to steel pipe or union complete in all respect as specified. |
| 79 | S & F in repair 600mm X 450mm bevelled edge mirror of selected quality glass, mounted on 9mm thick AC building board or commercial plywood and PVC moulding frame fancy type complete all as specified and directed. |
| 80 | S & F in repair chromium plated Towel ring fixed with and including CP brass screw and wooden/plastic cleat ( Minimum weight 90gms) complete all as specified. |
| 81 | S & F in repair Towel rail, 20mm dia brass chromium plated, 600mm long with fancy type brass chromium plated brackets on both sides and fixed with steel screws and wooden/rawl plugs complete all as specified. |
| 82 | S & F stainless steel sink with drainage board made of stainless steel 1.00mm thick for kitchen or laboratory, with plug, waste pipe, washers, including cantilever cast iron brackets, connecting union etc. with bedding layer in cement mortar on to dwarf wall, overall size 915mm X 460 mm with bowl size 410mm x 330mm x 160mm etc complete all as specified and as directed. |
| 83 | S & F 160mm bore PVC (SWR) pipes single socketed with rubber joint, in any length, laid in trenches or in floors / fixed to walls complete all as specified. |
| 84 | S & F 110mm bore PVC (SWR) pipes single socketed with rubber joint, in any length, with rubber ring joints, laid in trenches or in floors complete all as specified. |
| 85 | S & F 75mm bore PVC (SWR) pipes single socketed with rubber joint, in any length fixed to walls / floors or in trenches complete all as specified. |
| 86 | S & F 160mm bore PVC (SWR) bend suitable for pipe complete all as specified. |
| 87 | S & F 110mm bore PVC (SWR) bend suitable for pipe complete all as specified. |
| 88 | S & F 75mm bore PVC (SWR) bends suitable for pipe complete all as specified. |
| 89 | S & F 160mm bore PVC (SWR) junction, single T equal or unequal with or without door access complete all as specified. |
| 90 | M & L PVC(SWR) floor trap, 75mm dia outlet, plain with grating including jointing with solvent cement complete all as specified. |
| 91 | S & F in repair 150mm square size Grating PTMT (minium wt 100 gms) complete all as specified. |
| 92 | S & F 15mm bore galvanised iron water tubes medium grade with all fitting and fixed to wall, ceiling or laid in floor and trench complete all as specified. |
| 93 | S & F 20mm bore galvanised iron water tubes medium grade with all fitting and fixed to wall, ceiling or laid in floor and trench complete all as specified. |
| 94 | S & F 25mm bore galvanised iron water tubes medium grade with all fitting and fixed to wall, ceiling or laid in floor and trench complete all as specified. |
| 95 | S&F gun metal gate valve 20mm dia, cast copper alloy, screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe complete all as specified and directed. |
| 96 | S&F gun metal gate valve 25mm dia, cast copper alloy, screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe complete all as specified and directed. |
| 97 | S & F of 2000 litre rotational moulded polythylene water storage tanks triple layer (cylindrical vertical with closed top), hoisted and fixed in position with threaded type lid cover & 20mm bore GI tank nipple all as specified in SSR Part-I including connecting the overflow drain out, inlet and outlet pipes, tank nipple, elbow, bend, unions, sockets, etc. complete all as specified and as directed |
| 98 | S&F for 20mm Ball valves high pressure of PTMT with epoxy coated aluminium rod & high- density plastic bal screwed for iron pipe and fixed (min wt 15mm-142gms/20mm-210gms/25mm- 455gms/40mm-690gms) complete all specified and directed. |
| 99 | S&F for 25mm Ball valves high pressure of PTMT with epoxy coated aluminium rod & high- density plastic bal screwed for iron pipe and fixed (min wt 15mm-142gms/20mm-210gms/25mm- 455gms/40mm-690gms) complete all specified and directed. |
| 100 | S & F Anodised aluminium snap grid frame work for false ceiling all as specified with Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long including 4 mm thick pre-painted decorative Non asbestos fibre cement building boards fixed or laid/ inserted to timber/GI/Aluminium framework with screws complete all as specified and directed |
| 101 | M & L for applying 1 mm wall care putty on new and previously untreated plastered surface of walls, including preparation, to make the surface even and smooth complete all as specified. (for internal wall surface only) |
| 102 | M & L for new plastered surface of walls and applying two coat of acrylic distemper over one coat of alkali resistant primer complete all as specified. |
| 103 | M & L for preparation of new plastered surface applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm using roller complete all as specified and directed. |
| 104 | M & L for preparation of new steel surfaces of any description over 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and as directed. |
| 105 | E & M Division items |
| 106 | Taking down carefully copper/aluminium point wiring (light, fan, buzzer, socket or power) complete including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc including removing from site for taking credit and making good to disturbed surface of walls, floors etc as per existing specification complete all as specified and as directed. |
| 107 | M & L for point wiring with FRLSH stranded copper conductor 1.5 sqmm (nominal area), two single core, PVC insulated cable 1100 volts grade, ISI-694 marked in and including heavy duty,concealed PVC Conduit including all accessories etc ISI marked, with GI sunken box suitable for fixing switches, sockets and regulators including PVC insulated stranded copper conductor 1.5 sqmm (nominal area) single core cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed for One light point controlled by one switch. |
| 108 | M & L for point wiring with FRLSH stranded copper conductor 1.5 sqmm (nominal area), two single core, PVC insulated cable 1100 volts grade, ISI-694 marked in and including heavy duty, concealed PVC Conduit including all accessories etc ISI marked, with GI sunken box suitable for fixing switches, sockets and regulators including PVC insulated stranded copper conductor 1.5 sqmm (nominal area) single core cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed for One fan point/exhaust fan point controlled by one, one way switch 5 Amp. |
| 109 | M & L for point wiring with FRLSH stranded copper conductor 1.5 sqmm (nominal area), two single core, PVC insulated cable 1100 volts grade, ISI-694 marked in and including heavy duty, concealed PVC Conduit including all accessories etc ISI marked, with GI sunken box suitable for fixing switches, sockets and regulators including PVC insulated stranded copper conductor 1.5 sqmm (nominal area) single core cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed for one switch socket out let point 5 Amps on same board. |
| 110 | M & L for point wiring with FRLSH stranded copper conductor 1.5 sqmm (nominal area), two single core, PVC insulated cable 1100 volts grade, ISI-694 marked in and including heavy duty, concealed PVC Conduit including all accessories etc ISI marked, with GI sunken box suitable for fixing switches, sockets and regulators including PVC insulated stranded copper conductor 1.5 sqmm (nominal area) single core cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed for one switch socket out let point 5 Amps on independent board. |
| 111 | M & Lfor point wiring with FRLSH stranded copper conductor 4.0 sqmm (nominal area), two single core, PVC insulated cable 1100 volts grade, ISI-694 marked in and including heavy duty, concealed PVC Conduit concealed type of suitable size including all accessories etc ISI marked, with GI sheet pressed terminal box (recessed) with 3mm thick laminated hylem sheet top cover for fixing switches, sockets and regulators including PVC insulated FRLSH stranded copper conductor 4.0 sqmm (nominal area) single core cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed for 3 pin, 15 Amp socket outlet, independent.Note: The point wiring will be done from DBs to the switch sockets of any size with three wires running independently for each point and with no tappings. |
| 112 | S & F switch piano flush type button single pole one way 5 Amps all as specified and directed. |
| 113 | S & F Socket outlet 2 in 1, 3 pin, 5 amp flush type all as specified and directed. |
| 114 | S & F socket outlet combination 2 in 1, 3 pin 6 Amp flush type all as specified and directed. |
| 115 | S & F socket outlet combination 2 in 1, 3 pin 6 and 16 Amp flush type all as specified and directed. |
| 116 | S & F ceiling rose surface bakelite with three terminals all as specified and directed |
| 117 | S & F lamp holder insulated body with back plate for batten fitting including necessary all as specified and directed |
| 118 | S & F of surface mounting batten tube light fitting, integrated polycarbonate LED channel with white acrylic cover complete suitable for and including Lamp 1X20 Watt, (4 feet) fixed properly on wall surface and connecting complete from ceiling rose to fitting by three core copper conductor cable of overall sheathed size 2.5 Sqmm which shall be passed through PVC flexible conduit complete all as specified and directed.. |
| 119 | S & F of surface mounting batten tube light fitting, integrated polycarbonate LED channel with white acrylic cover complete suitable for and including Lamp 1X10 Watt, (2 feet) fixed properly on wall surface and connecting complete from ceiling rose to fitting by three core copper conductor cable of overall sheathed size 2.5 Sqmm which shall be passed through PVC flexible conduit complete all as specified and directed.. |
| 120 | S & F building security light LED fitting 35watt 230V AC outdoor type with high pressure die cast aluminum housing and heat resistant, epoxy powder coated dark graphite grey colour finish and prismatic polycarbonate cover with individual LED lences suitable for including lamp LED 35 watt. fixed/connect properly at directed location on building with IP 65/66 protection complete |
| 121 | Supply and fixing bracket for street light fittings of any size made out of Gl pipe medium grade 25/32 mm dia 1.25 mtr length bend to required size and shape including provision of clamps and fittings in position and two coat of aluminum paint over a coat of red oxide primer complete and including taking down old bracket all as specified and directed |
| 122 | Taking down old ceiling fan and S & F Ceiling fan 1200mm sweep single phase 230 volts AC, min air delivery 210 CFM with service valve 6.00 BEE 5 star rating with brushless direct current motor (BLDC) with blade down roads electronic regulator and complete accessories complete fixed properly on wall surface with the provisioning of suitable sizes of rag bolts, nuts, washer and to connect by using cable PVC insulated copper stranded conductor of size 2.5 Sqmm 3 core and overall PVC sheathed which shall be passed through PVC flexible conduit of length not exceeding 0.50 mtr all as reqd and as directed by Engr-in-Charge. Note:- Taking down Old Ceiling fan deposit to AGE Vairengte E/M Store (not in Schedule of Credit) |
| 123 | Taking down old exhaust fan and S & F for Plastic body Exhaust Fan 250 mm sweep, single phase 230 volts AC, 900 RPM four blade with louver shutters complete fixed properly on wall surface with the provisioning of suitable sizes of rag bolts, nuts, washer and to connect by using cable PVC insulated copper stranded conductor of size 1.5 Sqmm 3 core and overall PVC sheathed which shall be passed through PVC flexible conduit of length not exceeding 0.50 mtr all as reqd and as directed by Engr-in-Charge. |
| 124 | S & F electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection pipe etc complete all as specified and as directed.Note:- Taking down Old electric water heater deposit to AGE Vairengte E/M Store (not in Schedule of Credit) |
| 125 | S & F factory made distribution box sheet metal enclosure powder coated single pole and neutral phase (SPN) for fixing of MCBs, 8 way double door with Aluminum bus bar 100 Amp including grouting on the wall by means of screws and rawal plugs and making good disturbed surfaces complete all as specified and directed. |
| 126 | S & F MCB SPN of capacity 6-32 Amps, 240 V, 10 KA 'C' curve complete all as specified and directed. |
| 127 | S & F MCB SP of capacity 5-32 Amps, 240 V, 10 KA 'C' curve complete all as specified and directed. |
| 128 | Supply, installaion,commision and testing of 125KVA AMF Panel for DG sets Factory made inbuilt type control cubical made out of 3.15 mm thick CRCA sheet dust and vermin proof totally enclosed with front opening of 415 volts 3-phase 4-wire AC 50 Hz, including powder coated, copper bus bar of one and half times the rated load of min 125 KVA alternator complete with inbuilt battery charger, internal wiring with PVC insulated single core copper conductor multi stranded wire of 1100 volts grade of suitable capacity, fuses, name plates consisting of 4 pole MCCBs and Contactors of capacity as recommended by the manufacturer. Detachable cable gland plates, all controls, indicators and standard microprocessor based LED/LCD display for indicating voltage,current, frequency, speed, kW, kWH, PF, temperature, Battery voltage etc (g) Annuciation with indication lamps for: (i) Low lubricant oil pressure. (ii) High water temprature (iii) Engine over speed. (iv) Battery low voltage Controls:-(a) Load on Indication (b) Load off indication (c) Engine start push button (d) Engine stop push button (e) Fault accept/reset push button(f) Battery Charger (i) Transformer (ii) Rectifier (iii) Resistance (iv) DC Volt meter (v) DC Ammeter (vi) Charger rater selector switch complete all with mounted on Plateform suitable size accroding to panel design and size. Note:- The Qouted rate includes excavation, removing of soft soil and PCC, Cement Concrete foundation, filling and mass concrete (1:2:4) type B2 using 40 mm graded aggregate of size not less than as per SSR part-I specification complete all as specified and directed. |
| 129 | Supply & installation of of Gl Strip of size 25 mm X 4mm as a ring conductor network buried in earth 1.0 mtr below from surface all as directed at site by Engr-in-charge |
| 130 | Supply & Installation of Test point terminal block made of gun metal or phosphorus bronze size 75mm X 75mm X 25mm drilled and screwed including 3 nos. 8mm dia 25mm long hex. head screw complete all as specified and directed by Engr-in-charge |
| 131 | M & L for building earthing complete with galvanised steel earth plate electrode 600mm X 600mm X 6mm burried directly in ground (earth pit not less than 2.25 mtr deep below ground level) with top edged of the plate not less than 1.5 mtr below normal ground level, connected to galavanised iron earth lead by means of bolt, nut, check nut and washer of galavanised iron wire 4mm as earthing lead as shown in Electrical Plate No 3 of SSR Part I connected to earthing test point all as specified or indicated including testing on completion including necessary excavation and earth work in hard/dence soil, earth pit in PCC 1:3:6 type C1 using 20mm stone aggreate, funnel, 20mm dia Gl medium grade water pipe, 15mm dia GI light grade earth lead protection pipe, CI frame and cover, wire, copper lugs, wire mesh, charcoal or coke and common salt in alterative layer all around the earth electrode compacted thickness 15 cm including excavation and earth work pit cover including disposal of surplus soil to a distance not exceeding 50m, complete testing on completion all complete as shown in electrical plate No 3 of SSR Part I 2009 all as directed by Engr-in-Charge |
| 132 | M & L for building earthing complete with galvanised steel earth plate electrode 600mm X 600mm X 6mm burried directly in ground (earth pit not less than 2.25 mtr deep below ground level) with top edged of the plate not less than 1.5 mtr below normal ground level, connected to galavanised iron earth lead by means of bolt, nut, check nut and washer of galavanised strip 25x4 mm as earthing lead as shown in Electrical Plate No 3' of SSR Part I connected to earthing test point all as specified or indicated including testing on completion including necessary excavation and earth work in hard/dence soil, earth pit in PCC 1:3:6 type C1 using 20mm stone aggreate, funnel, 20mm dia Gl medium grade water pipe, 15mm dia GI light grade earth lead protection pipe, CI frame and cover, wire, copper lugs, wire mesh, charcoal or coke and common salt in alterative layer all around the earth electrode compacted thickness 15 cm including excavation and earth work pit cover including disposal of surplus soil to a distance not excessding 50m, complete testing on completion all complete as shown in electrical plate No 3 of SSR Part 1 2009 all as directed by Engr-in-Charge |
| 133 | Supply, fixing, commissioning & testing of XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, Electric power cable (heavy duty) with aluminium conductors, 1100 volts, grade cross sectional area 120sqmm 3.5 core laid in trenches/fixed to wall/under road/pipe etc with copper cable glands & copper thimbles complete all as specified and directed. |
| 134 | Supply, fixing, commissioning & testing of XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, Electric power cable (heavy duty) with aluminium conductors, 1100 volts, grade cross sectional area 10qmm 2.0core laid in trenches/fixed to wall/under road/pipe etc with copper cable glands & copper thimbles complete all as specified and directed. |
| 135 | Supply & laying, steel tubes, 25mm medium grade, galvanised iron water tubes with screwed socket joint together with and including all Gl fittings connection on waal or floor with clamps digging etc as per site requirement as per Engr-in-Charge |
| 136 | Supply & laying steel tubes, 50 mm medium grade, galvanised iron water tubes with screwed socket joint together with and including all Gl fittings connection on waal or floor with clamps digging etc as per site requirement as per Engr-in-Charge |
| 137 | Excavating in trenches, n exc 1.50 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out soft/ loose type of soil complete all as specified and directed. |
| 138 | Returning, filling in trenches including spreading, leveling watering and ramming in layers not exceeding 25cm all as specified. |
| 139 | Removing of surplus soil not exceeding 50 m and deposited where directed at a level not exceeding 1.50m above the starting point all as specified. |
| 140 | M & L for sand cushioning by spreading in trenches crushed sand by gently by punning down manually as in cable protection all as specified and as directed by Engineer -in-charge.Note : Thickness of sand cushioning after punning down will be measured. |
| 141 | M & L for laying of bricks locally available sub class 'B' bricks (old size) for cable protection cover laid flat and dry in trenches over the cable perpendicular to the direction of cable complete all as specified and directed by Engr-in-Charge Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 18, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 10, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 10 daysAug 13, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 13 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender