Tender For Repair / Replacement Of Wooden / Steel Furniture Including Painting To Steel Furniture And Polishing / Varnishing Of Wooden Furniture At Af Stn Purnea Under Age (I) (Af) Purnea.
Tender Value
7 Lakhs
Estimated cost
Bid Submission
06 Aug 2026
19 days left
EMD
14000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Purnia → Bihar
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repair / Replacement Of Wooden / Steel Furniture Including Painting To Steel Furniture And Polishing / Varnishing Of Wooden Furniture At Af Stn Purnea Under Age (I) (Af) Purnea.
BOQ
| Sl. No. | Item Description |
| 1 | REPAIR TO CHAIR EASY, FD-229 |
| 2 | Material and labour for replacement of broken/damaged front leg of existing size of chair easy with new leg of Ist class hard wood including providing of PVC shoe at the bottom of the legs with screw (each leg shall be measured), complete all as shown on drawing & directed by Engineer-in- Charge. |
| 3 | All as per item No 1.01 above but for rear leg. |
| 4 | All as per item No. 1.01 above but for side/front/back rail of seat of chair easy of existing size including drilling holes for re-canning. |
| 5 | Material and labour for replacement of broken/damaged wooden arm rest of chair easy of existing size, complete all as specified and directed. |
| 6 | REPAIR TO CHAIR DINING,FD-228/FD-279 |
| 7 | Removing /taking out existing unserviceable damaged/broken rear leg and supply and fixing of new rear leg made out of well seasoned 1st class hard wood free form knot, sap wood etc of existing size including providing of PVC shoe at the bottom of the legs with screw, complete all as shown on drawing & directed by Engineer-in- Charge. |
| 8 | All as per item No 2.01 above but for front leg of existing size. |
| 9 | All as per item No 2.01 above but for front/back/side rails of existing size. |
| 10 | Removing of old broken stiffner and replacing with new stiffner of existing size, complete all as shown on drawing & directed by Engineer-in- Charge. |
| 11 | Material and labour for preparation of old exposed wooden surfaces by scrapping with sand paper and smoothing of surface, filling of bore holes with wooden putty paste rubbing of surface with sand paper till smoothening and polishing to chair dining all as directed by Engineer–in-Charge. |
| 12 | REPAIR TO CHAIR WRITING, FD-280 |
| 13 | Removing /taking out existing unserviceable damaged/broken rear leg and supply and fixing of new leg made out of well seasoned 1st class hard wood free form knot, sap wood etc of existing size including providing of PVC shoe at the bottom of the legs with screw, complete all as shown on drawing & directed by Engineer-in- Charge. |
| 14 | All as per item No 3.01 above front leg of exisitng size. |
| 15 | All as per item No 3.01 above but arms of exisitng size. |
| 16 | All as per item No 3.01 above but back/front/side rail of exisitng size including drilling holes for re-caning and finished with french polish, complete all as shown on drawing & directed by Engineer-in- Charge. |
| 17 | Material and labour for preparation of old exposed wooden surfaces by scrapping with sand paper and smoothing of surface, filling of bore holes with wooden putty paste rubbing of surface with sand paper till smoothening and polishing to chair writing, complete all as specified & directed by Engineer-in-Charge. |
| 18 | REPAIR TO TABLE DINING 6/8 PERSONS, FD-273 |
| 19 | Taking out old userviceable top from table dining 6/8 pers and supply and fixing new top of existing size made out of 19/20mm thick, commercial face particle board bonded teak veneered finish of approved quality including Providing 19 x 4mm size 1st class hard wood semi oval shape beading all around, complete all as shown on drawing & directed by Engineer-in- Charge. |
| 20 | Material and labour for replacement of broken/damaged side long rail of existing size of table dining 6/8 persons with new side long rail of 1st class hard wood and fixing with bamboo nails, complete all as specified and directed and shown on drawing. |
| 21 | Material and labour for replacement of broken/damaged side short rail of existing size of table dining 6/8 persons with new side short rail of 1st class hard wood and fixing with bamboo nails, complete all as specified and directed and shown on drawing. |
| 22 | Material and labour for replacement of broken/damaged legs of existing size of table dining 6/8 pers with new leg of 1st class hard wood including providing of PVC shoe at the bottom of the legs with screw (each leg shall be measured), complete all as specified and directed and shown on drawing. |
| 23 | Material and labour for preparation of old exposed wooden surfaces by scrapping with sand paper and smoothing of surface, filling of bore holes with wooden putty paste rubbing of surface with sand paper till smoothening and polishing to table dining complete all as specified & directed by Engineer-in-Charge. |
| 24 | REPAIR TO TABLE 900 mm X 900 mm X 760 mm, FD-88/FD-291 |
| 25 | Taking out old userviceable top from table 900 mm X 900 mm X 760 mm and supply and fixing new top made out of 19/20mm thick, commercial face particle board teak veneered finish of approved quality including Providing 19 x 4mm size 1st class hard wood semi oval shape beading all around, complete all as specified and directed and shown on drawing. |
| 26 | Removing/taking out the existing unserviceable broken legs and Supply and fix new leg of existing size made out of well seasoned1st class hard wood including providing of PVC shoe at the bottom of the legs with screw, complete all as specified and directed and shown on drawing. |
| 27 | All as per item No 5.02 above but for top rail made out of well seasoned 1st class hard wood. |
| 28 | Material and labour for preparation of old exposed wooden surfaces by scrapping with sand paper and smoothing of surface, filling of bore holes with wooden putty paste rubbing of surface with sand paper till smoothening and polishing to table 900 mm X 900 mm X 760 mm, complete all as specified and directed and shown on drawing. |
| 29 | REPAIR TO TABLE PEG, FD-384 |
| 30 | Taking out old broken/damaged leg of table peg and Supply and fix new leg made out of well seasoned 1st class teak wood, free from kont, sap wood etc of size 360 x 45x 45mm including Providing PVC shoe at the bottom of the legs fixed with screw, complete all as specified and directed and shown on drawing. |
| 31 | All as per item No 6.01 above but for top rail made out of well seasoned1st class hard wood. |
| 32 | Taking out old userviceable top from table peg of size 300 x 450mm and supply and fix new top made out of 19/20mm thick, commercial face particle board teak veneered finish of approved quality including Providing 19 x 4mm size 1st class hard wood semi oval shape beading all around, complete all as specified and directed and shown on drawing. |
| 33 | Material and labour for preparation of old exposed wooden surfaces by scrapping with sand paper and smoothing of surface, filling of bore holes with wooden putty paste rubbing of surface with sand paper till smoothening and polishing to table Peg, complete all as specified and directed and shown on drawing. |
| 34 | TABLE WITH DRAWER (900 mm X 600 mm X 760 mm), FD-283/FD-232 |
| 35 | Taking out old userviceable top from table 900mm X 600 mm and supply and fixing new top made out of 19/20mm thick, commercial face particle board bonded teak veneered finish of approved quality including Providing 19 x 4mm size 1st class hard wood semi oval shape beading all around, complete all as specified and directed and shown on drawing. |
| 36 | Removing/taking out the existing unserviceable broken legs and Supply and fix of new leg round or square made out of well seasoned 1st class hard wood free from knot, sap wood etc of existing size including providing of PVC shoe at the bottom of the legs with screw, complete all as specified and directed and shown on drawing. |
| 37 | All as per item No 7.02 above but top rail of existing size. |
| 38 | Material and labour for preparation of old exposed wooden surfaces by scrapping with sand paper and smoothing of surface, filling of bore holes with wooden putty paste rubbing of surface with sand paper till smoothening and polishing to table 3'x2' with/without drawer, complete all as specified and directed and shown on drawing. |
| 39 | TABLE BED SIDE (450 mm X 230 mm X 510 mm), FD-248/FD-276 |
| 40 | Taking out old userviceable top from table bed side and supply and fix new top of existing size made out of 19/20mm thick, commercial face particle board teak veneered finish of approved quality including Providing 19 x 4mm size 1st class hard wood semi oval shape beading all around, complete all as specified and directed and shown on drawing. |
| 41 | Taking out broken damaged back plywood from back of table bed side of size 610x450mm and Supply and fix new plywood BWR Gde 6mm thick commercial, complete all as specified and directed and shown on drawing. |
| 42 | Taking out broken/damaged leg of table bed side and Supply and fix new legs of size 100x45x45mm made out of well seasoned 1st class hard wood, free from knot, sap wood etc duly fixed with PVC shoe at the bottom of legs with screws, complete all as specified and directed and shown on drawing. |
| 43 | Material and labour for preparation of old exposed wooden surfaces by scrapping with sand paper and smoothing of surface, filling of bore holes with wooden putty paste rubbing of surface with sand paper till smoothening and polishing to table bedside, complete all as specified and directed and shown on drawing. |
| 44 | TABLE CENTRE, FD-274 |
| 45 | Taking out old userviceable top from table center and Supply and fix new top of existing size made out of 19/20mm thick, commercial face particle board teak veneered finish of approved quality including providing 19 x 4mm size 1st class hard wood semi oval shape beading all around, complete all as specified and directed and shown on drawing. |
| 46 | All as per item No 9.01 above but top rail made out of well seasoned1st class hard wood. |
| 47 | Material and labour for preparation of old exposed wooden surfaces by scrapping with sand paper and smoothing of surface, filling of bore holes with wooden putty paste rubbing of surface with sand paper till smoothening and polishing to table bedside, complete all as specified and directed and shown on drawing. |
| 48 | RE-CANING OF CHAIR Material and labour for re-canning of chair any type with 2mm wide plastic cane half oval shape to a true shape for general caning as per godrej pattern and 4mm wide plastic cane for bordering around of caning of chair all types, complete all as specified and directed and shown on drawing. |
| 49 | POLISHING TO ALL WOODEN ITEMS OF FURNITURE (Only Polishing) |
| 50 | Material and labour for preparation of old exposed wooden surfaces of chair dining other than those already repaired and polished above by scrapping with sand paper and smoothing of surface, filling of bore holes with wooden putty paste rubbing of surface with sand paper till smoothening and polishing to chair dining, complete all as directed by Engineer–in-Charge. |
| 51 | All as per item 11.01 above but for chair easy. |
| 52 | All as per item 11.01 above but for Table Peg. |
| 53 | All as per item 11.01 above but for Table bedside. |
| 54 | All as per item 11.01 above but for Table writing. |
| 55 | All as per item 11.01 above but for chair writing. |
| 56 | All as per item 11.01 abvoe but for bed Plytop /Bed Hard. |
| 57 | All as per item 11.01 abvoe but for Table dressing gents. |
| 58 | All as per item 11.01 abvoe but for Table Dressing Ladies. |
| 59 | All as per item 11.01 abvoe but for Table Dining. |
| 60 | BED PLYWOOD TOP, FD-246 |
| 61 | Removing the old unserviceable head board from bed plywood top, Supply and fix new head board of size 900x660mm made out of 02 nos of vertical of size 60x60x660mm using second class hard wood (vertical shall be shaped as legs of size 60 x60mm at top and 30 x30mm at the bottom) and 2 Nos of stiffeners 40 x60mm (top and bottom round shape) with 75 mm width and 22 mm thick soft wood battens between stiffeners covered with 4mm thick plywood OST exterior grade on both side and 12mm half rounded taak wood beaing round the edges of plywood by providing 2 Nos of 25mm size round head brass screws for MNF set key holes and applying two coats of french polishing etc., complete all as specified and directed and shown on drawing. |
| 62 | All as per item No 12.01 above but foot board of bed plywood top of size 900x 500mm. |
| 63 | Supply and fix long rail of bed plywood top of size 90x35mm, 1980mm long made from 1st class teack wood and providing brackets made from flat iron -02 Nos of size 35x6mm thick 200mm long on both ends and finishing the exposed wooden surface with french polishing including removing the old unserviceable long rails, complete all as specified and directed and shown on drawing. |
| 64 | Removing the old unserviceable pealed plywood from bed plywood top, Supply and fix new plywood commercial type, exterior grade, approved quality of size 1900x900mm 12mm thick on both side, complete all as specified and directed and shown on drawing. |
| 65 | Material and labour for preparation of old exposed wooden surfaces by scrapping with sand paper and smoothing of surface, filling of bore holes with wooden putty paste rubbing of surface with sand paper till smoothening and polishing to Bed plywood top, complete all as specified and directed and shown on drawing. |
| 66 | TABLE OFFICE CLERK STEEL (FD-84M / FD-1004) |
| 67 | Removing of old unserviceable top from Table Office clerk steel and supply and fixing the new top of same size made out of 18/19mm thick pre-laminated particle board teak faced with 4mm thick teak wood beading all-around the table top, complete all as specified and directed and shown on drawing. |
| 68 | Removing of old unserviceable lock from Table Office clerk steel and supply and fixing new lock with two keys, complete all as specified and directed and shown on drawing. |
| 69 | Removing of old unserviceable drawer from Table Office clerk steel and supply and fixing the new drawer of same size and shape made out of 1mm thick MS black sheet all as shown on drawing and applying one coat of synthetic enamel olive green paint with spray painting (Internally and externally) over a coat of primer after preparation of surfaces, complete all as specified and directed and shown on drawing. |
| 70 | Supply and fix in replacement 100mm long piece of 25 Sqmm MS tube having wall thickness of 1.6mm including welding to Table Office Clerk steel, complete all as specified and directed and shown on drawing. |
| 71 | Supply and fix in replacement PVC shoes to Office clerk steel, complete all as specified and directed and shown on drawing. |
| 72 | Removing of old unserviceable Drawer Box from existing Table Office Clerk Steel and supply and fixing the new Drawer Box of same size and shape made out of 1mm thick MS black Sheet all as shown on drg and applying one coat of synthetic enamel olive green paint with spray painting (Internally and Externally) over a coat of primer after preparation of surfaces, complete all as specified and directed and shown on drawing. |
| 73 | CHARPOY GI PIPE WITH PLY TOP, FD-220 :- |
| 74 | Removal of existing unserviceable Ply Top of Charpoy GI pipe and Supply and fix of 12mm thick plywood BWR of approved quality size 1980mm X 900 mm, cutting into correct dimension and rounding at edges to give it a perfect shape with 14 Nos suitable dia and length of nuts and bolts, complete all as specified and directed and shown on drawing. |
| 75 | Supply and fix GI Elbow 32mm dia heavy duty ISI marked after taking out old unserviceable(U/S) GI elbow, complete all as specified and directed and shown on drawing. |
| 76 | Supply and fix GI check nut 32 mm size, heavy duty ISI marked after taking out old unserviceable(U/S) check nut from charpoy GI pipe, complete all as specified and directed and shown on drawing. |
| 77 | Taking out broken/damaged long rail from charpoy GI pipe and Supply and fix new long rail of charpoy GI pipe 32mm dia med grade, ISI marked including cutting, threading, complete all as specified and directed and shown on drawing. |
| 78 | Taking out broken/damaged short rail from charpoy GI pipe and fixing short rail made out from old pipe including cutting for required size and shape & threading and fixing (old pipe shall be obtained from Ser Item No 14.04), complete all as specified and directed and shown on drawing. |
| 79 | Taking out unserviceable legs from charpoy GI pipe and fixing leg made out of old pipe including cutting of required size and shape & threading and fixing (Old pipe shall be obtained from Ser Item No. 14.04 and 14.05), complete all as specified and directed and shown on drawing. |
| 80 | REPAIR TO CHAIR VERANDAH (FD-256 / FD - 75 M) Removing old unserviceable cane from chair verandah and recaning with new plastic cane 4mm width half round including Material and labour for painting two coats of white synthetic enamel paint in approved shade over a coat of red oxide primer on entire steel/iron surface of chair before recaning and supply and fix of new hard rubber shoes 15mm dia at bottom of legs after taking out old toes, complete all as specified and directed and shown on drawing. |
| 81 | REPAIR TO ALMIRAH STEEL LARGE/MEDIUM (FD-1031/1032 / FD - 67 M) |
| 82 | Material and labour for one coat spray painting with synthetic enamel paint of approved shade on almirah steel large internally and externally including shelves & internal locker complete after preparation of old painted steel surfaces by scrapping/rubbing down all as directed by Engineer –in- Charge. |
| 83 | All as per item No 16.01 above but for Almirah steel medium with shelves. |
| 84 | Material and labour for repairs of legs of almirah steel large by replacing old/damaged legs with 1mm thick MS sheet and fixing the new legs by welding to almirah steel large and applying one coat painting with synthetic enamel paint 1st garde on new legs externally complete after preparation of old/new steel surfaces by scrapping/rubbing down, complete all as specified and directed and shown on drawing. |
| 85 | Taking out old unserviceable lock from almirah large/med steel and Supply and fix new lock best quality locally availabe, complete all as specified and directed and shown on drawing. |
| 86 | Taking out old unserviceable handle from almirah large/med steel and Supply and fix new one with Godrej quality locally available, complete all as specified and as directed. |
| 87 | Taking out old unserviceable handle from bed side locker steel and Supply and fix new one with best quality locally available, complete all as specified and directed and shown on drawing. |
| 88 | TABLE DRESSING GENTS (FD-31M / FD - 230) |
| 89 | Removing/Taking out existing unserviceable damaged/broken frame of Table Dressing Gents and Supply and fix of frame made out of well seasoned 1st class hard wood of existing, complete all as specified and directed and shown on drawing. |
| 90 | Removing old unserviceable broken looking mirror form Hat Stand and Supply and fixing new approved quality 5 to 6mm thick (plus/minus 5% tolerance) electro copper plated sheet glass mirror of size 460 x 360mm of make Modi/Atul/Saint Gobin duly fixed with wooden frame, complete all as specified and directed and shown on drawing. |
| 91 | Material and labour for repair to table dressing gents by replacing of broken/damaged back with new 6mm thick commercial plywood BWR typeof existing size and finished with French polish, complete all as specified and directed and shown on drawing. |
| 92 | Material and labour for repairs to drawers of table dressing gents by replacing broken/damaged bottom with new 6mm thick commercial plywood BWR type of existing size including providing suitable knobs, complete all as specified and directed and shown on drawing. |
| 93 | Material and labour for preparation of old exposed wooden surfaces by scrapping with sand paper and smoothing of surface, filling of bore holes with wooden putty paste rubbing of surface with sand paper till smoothening and polishing to table dressing gents, complete all as directed by Engineer –in- Charge. |
| 94 | SOFA SET 4/5 SEATER (FD- 281 /FD-373) :- |
| 95 | Removing/taking out the existing unserviceable/damaged cushion and Supply and fix new cushion of existing size made out of 100mm thick foam rubber cushion, 40 density (570x540mm) conforming to IS-174-1960 cord type with tapestry cloth cover of shade approved by AGE(I), complete all as specified and directed and shown on drawing. |
| 96 | M&L for preparation of old exposed wooden surfaces by scrapping with sand paper and smoothing of surface, filling of bore holes with wooden putty paste rubbing of surface with sand paper till smoothening and polishing to sofa, complete all as specified and directed and shown on drawing. |
| 97 | All as per item no. 18.00 above but for Sofa set 04 seater. |
| 98 | All as per item no. 18.00 above but for Sofa set 02 seater. |
| 99 | TABLE COMPUTER(TP):- Removing unserviceable Casters of computer table/chairs and Supply and fix new castors 50mm /existing dia of best quality of existing size, complete all as specified and directed and shown on drawing. |
| 100 | CHAIR REVOLVING CUSHIONED WITH ARMS ALL TYPES(TP):- |
| 101 | Replacement of hydraulic height adjustment base assembly of chair revolving same as existing in chair, complete all as specified and directed and shown on drawing. |
| 102 | Replacement of new arms with polyurethane reinforced with MS insert arms same as existing in chair, complete all as specified and directed and shown on drawing. |
| 103 | Replacement of the old broken seat from chair and providing new seat made out of 12mm ply wood same as existing in chair, complete all as specified and directed and shown on drawing. |
| 104 | Removing the old torn/damaged tapestry cloth/rexine from the seat of the chair and providing the same with tapestry/rexine over a layer of foam(75MM thick, 40 density) same as existing in chair, complete all as specified and directed and shown on drawing. |
| 105 | Removing unserviceable costers of chair revolving and Supply and fix of new costers of existing size best quality, complete all as specified and directed and shown on drawing. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 18, 2026
11:30 IST
Tender Published
Tender notice published.
TodayAug 06, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 19 daysAug 08, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 21 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender