Tender For special Repair To Bldg No T-17 (Stocking Wing) And Toilets In Bldg No P-61 Army Avn Sqn And Provn Of Toilets And Car Parking Near Bldg No P-95 Under Aor Of Age B/R Of Ge (S) Mamun
Tender Value
40.47 Lakhs
Estimated cost
Bid Submission
07 Aug 2026
20 days left
EMD
80953
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Pathankot → Punjab
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for special Repair To Bldg No T-17 (Stocking Wing) And Toilets In Bldg No P-61 Army Avn Sqn And Provn Of Toilets And Car Parking Near Bldg No P-95 Under Aor Of Age B/R Of Ge (S) Mamun
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of brickwork or stone/boulder masonry built in cement mortar including all quoins, arches, pillars etc., but excluding ashlar facing, dressed stone work and precast concrete articles complete all as specified & directed. |
| 2 | Demolition of cement concrete (unreinforced) or tiling etc in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified & directed. |
| 3 | Dismantling floor, hearth or wall tiling and terrazo topping incl cement mortar bedding (but not backing) removing serviceable tiles and rubish off the premises, complete all as specified and directed. |
| 4 | Taking down cement plaster/wall tiles including backing etc from brick/stone walls / concrete surfaces including raking out joints, hacking for key , scrubbing down with water etc complete all as specified and directed |
| 5 | Taking down chowkats or frames including shutters (without taking off shutters from the frame) not exc. 1.5 Sqm each complete all as specified & directed. |
| 6 | Taking down chowkats or frames including shutters (without taking off shutters from the frame) exc. 1.5 Sqm but n exc 4.0 sqm each complete all as specified & directed. |
| 7 | Hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new onces exc 1.5 Sqm complete all as specified & directed. |
| 8 | M&L for Brickwork with Fly Ash Bricks (old size), straight or curved on plan exceeding 6 metre mean radius built in cement sand mortar 1:6 complete all as specified & directed. |
| 9 | M&L for Brickwork with Fly Ash Bricks (old size), in half brick thick walls straight or curved on plan exceeding 6 metre mean radius built in cement sand mortar 1:4 complete all as specified & directed. |
| 10 | S&F box type steel windows comprised of tubular frame and shutters made out of 1.25 mm thick M S sheet tube factory made with double side shutters wire gauged shutter & glass glazed shutter (wire cloth and glass panes only shall be measured and paid seperately) with side hung shutters with steel handle and steel peg stay dovetailed or welded incl 2 Nos tower bolts 100 mm long for each leaf and 10 mm square bar grills at spacing as shown on drg welded to FI frame work, including other fittings, hinges, handles, tarred hold fasts, PCC blocks etc all as shown on drg No CEPZ/TD-354/09 sheet 1/3 to 3/3 complete all as specified and directed. |
| 11 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and crew withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws complete all as specified & directed. |
| 12 | S&F factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ choowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs fasteners shall be paid for separately) complete all as specified & directed. |
| 13 | S&F 4 mm thick sheet glass ordinary quality and glazing with oil putty in square not exc. 0.5 sqm in each pane complete all as specified and directed. |
| 14 | S&F 3 mm thick figured sheet glass ordinary quality and glazing with oil putty in square not exc. 0.5 sqm in each pane complete all as specified and directed. |
| 15 | S&F Butt hinges 100 mm long, stainless steel, medium weight and fixed complete all as specified & directed. |
| 16 | S&F Aluminium alloy, anodised, sliding door bolt 250 mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or castaluminium alloy and fixed complete all as specified and directed. |
| 17 | S&F Aluminium, anodised, barrel tower bolts 150 mm of extruded section and fixed complete all as specified and directed. |
| 18 | S&F Aluminium, anodised, handles 125 mm of extruded section and fixed complete all as specified and directed. |
| 19 | S&F Aluminium, anodised, handles 150 mm of extruded section and fixed complete all as specified and directed. |
| 20 | S&F Mild steel, 300mm, ordinary rat tail rod patttern springs includding roller and roller plate complete fixed with screw or necessary welding to pressed steel door frame complete all as specified & directed. |
| 21 | S&F Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with statinless steel wire staples complete all as specified & directed. |
| 22 | S&F in repairs Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with statinless steel wire staples complete all as specified & directed. |
| 23 | S&F stainless steel peg set of six of size 400mmx30mmx3mm size fitted with machine screw and wooden and plastic cleats (minium wt 190gms) complete all as specified and directed. |
| 24 | M& L for cutting to existing GI fittings 25/40 mm dia (existing pipe) for addn/altn branch connection and inserting of T complete etc.complete all as specified & directed. |
| 25 | M& L for cutting to existing GI fittings 15/20 mm dia (existing pipe) for addn/altn branch connection and inserting of T complete etc.complete all as specified & directed. |
| 26 | M & L for Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc; and cutting chases for concealed water tubing, etc., and making good, cutting not exc 10 cm girth in brick walls complete all as specified & directed. |
| 27 | Taking up or down steel tubing of 15mm bore pipe and connection laid in trenches or floors or fixed to walls and including cleaning for refixing or removal to store with all fittings complete all as specified and directed. |
| 28 | Supply & Fixed steel water tubing 15 mm bore medium grade galvanised with all fittings (ISI marked) fixed complete to walls, ceiling or laid in floors complete all as specified & directed. |
| 29 | Taking up or down steel tubing of 20mm bore pipe and connection laid in trenches or floors or fixed to walls and including cleaning for refixing or removal to store with all fittings, complete all as specified and directed. |
| 30 | Supply & Fixed steel water tubing 20 mm bore medium grade galvanised with all fittings (ISI marked) fixed complete to walls, ceiling or laid in floors complete all as specified and directed. |
| 31 | Fixing only old steel tubing 20 mm bore and connections in new or old position (walls, ceiling, floor etc.) complete all as specified and directed.Note :- Servicable pipe retrieved by taking up / down existing one shall be used. |
| 32 | S&F GI pipe 32 mm dia light grade in short length as spout pipe in sunken floor slab laid in slope to brick wall with PCC 1: 2:4 type B -1 using 20 mm graded stone aggregate complete all as specified and directed. |
| 33 | Supply & Fixed steel water tubing 25 mm bore medium grade galvanised with all fittings (ISI marked) fixed complete to walls, ceiling or laid in floors complete all as specified and directed. |
| 34 | Supplied and fixed Rotational moulded polyethlene water storage tanks three layers of 1000 ltrs capacity ISI marked (cylindrical vergical with closed top) hoisted and fixed in position all as specified in SSR Part I including 20mm thick Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe and fixed. (Minimum weight 20mm-210 gms including Dismantling of old brocken water tanks and refixing of inlet, outlet & over flow pipe etc. complete all as specified and as directed. |
| 35 | S&F 20mm Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight - 210 gms) complete all as specified and directed. |
| 36 | S&F Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe 25mm bore dia and fixed complete all as specified and directed. |
| 37 | Supply & fixed Stop valve (ISI Marked), cast copper alloy screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 20 mm bore and fixed complete all as specified & directed. |
| 38 | Supply & fixed Stop valve (ISI Marked), long shank and cup, cast copper alloy screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 15 mm bore and fixed complete all as specified & directed. |
| 39 | Supply & fixed Bib tap 15 mm bore long body, Brass CP, fancy type (long shank), with crutch or butterfly handle screwed down screwed for iron/PVC pipe or for brass ferrule and fixed complete all as specified. |
| 40 | All as per description of serial item No. 39 here-in-before but as in repairs |
| 41 | Supply & fixed Stop valve /Angle valve (ISI Marked), fancy type, chromium plated with long shank and cup (concealed type). screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron /PVC pipe or for unions of 15 mm bore andcomplete all as specified. |
| 42 | S&F 15mm dia pillar tap cast copper alloy fancy type capstan heads chromium plated screwed down high pressure with or without letered \\"Hot or Cold\\" high pressure with long screwed shanks & fly nuts screwed for iron pipe etc. complete all as specified and directed. |
| 43 | Supply & fixed CP Brass shower rose 200x200 mm size with flexible brass arm 450-550mm long complete all as specified and directed. |
| 44 | S&F in repair CP Brass Hand Shower (Health Faucet) with 8 mm dia,1.2 m long Long Flexible Tube Chrome Finish & Wall Hook for Water closet complete all as specified and directed. |
| 45 | Supply & fixed Soap dish (material SS finish, glossy) fixed to plugs with CP brass screws complete all as specified and directed. |
| 46 | Supply & fixed, Vitreous china wash down water closet pan (Pedestal pattern) white (excl fixing bolts, flushing cistern and flush pipe) but including plastic water closet seat, white, closed pattern with flat bottom and cover and mild steel CP or aluminised hinging device complete all as specified & directed. |
| 47 | Supply & fixed in repair Vitreous china squatting pan of pattern, long pan, 'Orissa pattern', size 580 x 440 mm white with integral foot rests (excl flushing cistern and flush pipe) but including provision concrete bedding CI floor trap etc.complete all as specified and directed. |
| 48 | Supply & fixed bevelled edge looking mirror, 5.5mm thick of selected quality glass, mounted on 6 mm dia SS clamp on counter complete all as specified. |
| 49 | Supply & fixed Push botton type PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle (incl brackets & flush pipe PVC 32 mm dia) capacity of 10 Litres complete all as specified & directed. |
| 50 | All as per description of serial item No. 49 here-in-before but as in repairs |
| 51 | Supply & fixed in repair Vitreous China Urinal, Half stall type, white including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, , flush pipe, grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) fixed incl supply and fixing of CP coupling, waste pipe and cp brass spreder all necessary fittings complete all as specified and directed. |
| 52 | Supply & fixed Vitreous china wash basin, flat back white, size 550 x 400 mm excl taps, waste chain and plug and porcelain stopper but including brackets complete all as specified & directed. |
| 53 | All as per description of serial item No. 52 here-in-before but as in repairs |
| 54 | Supply & fixed Vitreous china wash basin, white , size 630mm x 450 mm excl taps, waste chain and plug and porcelain stopper complete all as specified & directed. |
| 55 | S & F corrugated waste pipe, 32 mm dia, suitable for WHBs/sinks/Urinal, including threaded PVC socket suitable for shank of waste coupling complete all as specified & directed. |
| 56 | Supply & fixed Brass CP towel rail 20mm dia 'D' type 60 cm long between flanges complete all as specified and directed. |
| 57 | Supply & fixed PVC connection 15 mm bore with PTMT nuts of length 450 mm long complete all as specified & directed. |
| 58 | Supply & fixed in repair PVC (SWR) floor trap, dia of outlet in 75 mm, plain excluding grating, but including jointing with solvent cement complete all as specified & directed. |
| 59 | Supply & fixed PVC grating square, 100 mm (Hinge pattern and with or without hole) complete all as specified & directed. |
| 60 | Supply & fixed 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls, floors or laid in trenches complete all as specified & directed. |
| 61 | All as per description of serial item No. 60 here-in-before but as in repairs |
| 62 | Supply & fixed 110 mm bore PVC (SWR) bends any radius, with or without excess door complete all as specified & directed. |
| 63 | Supply & fixed 75 mm bore PVC (SWR) vent cowl complete all as specified & directed. |
| 64 | Supply & fixed 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints , fixed to walss, laid in trenches or in floor complete all as specified & directed. |
| 65 | Supply & fixed 75 mm bore PVC (SWR) bend any radius, with or without excess door complete all as specified & directed. |
| 66 | Cleaning/clearing of sewage line (including manholes) 100mm to 150mm bore of any description, underground at any depth, removing any type of blockage including desilting, descaling & dechocking of drains as well as manholes and depositing the sludge in a pit (including digging of pit) not less than 100 metres away from the site of cleaning and covering the sludge with layer of 2.5cm thick layer of earth and spraying unslacked lime on the pit and making sewage line smooth functional complete all as specified and directed. |
| 67 | Supply, laying & jointing reinforced concrete pipe, 150 mm bore, class NP-2, laid and jointed complete with collars and testing complete all as specified and directed. |
| 68 | M&L for concrete bed in cement concrete 1:4:8, type D-2 (using 40mm graded crushed stone aggregates) to drain pipes 150mm bore dia, including packing under and haunching against the sides of pipe after they are laid and tested complete all as specified and directed. |
| 69 | M&L for Septic tank 10 Users designed to carry sewage and sullage water, complete including excavation and earth work in any type of soil, PCC 1:4:8 under foundation, RCC M-30 Design Mix in Roof Slab PVC rungs etc including Vent shaft , manhole openings with cover and making connection etc., of effective depth 1.5 metre and overall depth of 3 metre complete all as described and shown on Drg No CEPZ/C-TD/013 /13 dated 11 -09- 2013 sheet 1/5 to 5/5. |
| 70 | M&L for Soakage wells of size 2.40m dia x 3.00 m depth including excavation, in any type of soil, foundation in PCC 1:3:6, walls of honey combed brick masonry in CM 1:4 with sub class B bricks, top ring of RCC, M-25 design mix concrete including intercepting chamber and screen chamber made of Brick masonary in CM 1:4, RCC cover slab in M-25 design mix & SFRC MH cover incl interconnecting pipes of RCC/DWC complete filled with brick bats complete all as shown on Drg No CEPZ/C-TD/013 /13 dated 11 -09- 2013 sheet 1/5 to 5/5 . |
| 71 | M&L for Non skid ceramic jointless coloured tiles, 7 to 8 mm thick (square/ rectangular) area of each tile exc 0.11 sqm but nexc 0.18 sqm in floor etc set & jointed in neat cement slury & pointed in white or coloured cement mixed with pigment to match over and including 15mm thick screed layer in cement mortar 1:6 complete all as specified and directed . |
| 72 | M&L for Glazed ceramic coloured tiles of size 450mmx300mm, thickness 7mm as in vertical surfaces such as skirting, dado, wall etc., set and jointed in neat cement slurry and pointed with coloured cement to match over and including 10mm thick rendering in cement mortar 1:4 complete all as specified & directed. |
| 73 | M&L for 18 mm thick green marble (of any type) work (table rubbed & polished) in steps, jambs, pillars, window-cills cooking platforms & like including pointing into white cement (1:2) using marble dust with admixture of pigment to match shade of granite laid over and including Screed bed or bedding layer of mortar 15mm thick for laying floor in CM 1:4 finished even & rough to receive top layer complete all as specified and directed. |
| 74 | M&L for Machine cut Kota stone slab flooring not less than 18-20mm thick (size of stone shall not less than 55cmx55cm), 75mm wide white marble border alround, laid over & including 15 mm thick screed base in CM 1:6, jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, grinding and polishing to yield mirror finish with machine complete all as specified & directed.. |
| 75 | M&L for Machine cut Kota stone slab not less than 16mm thick as in riser of steps, skirting, dado and pillar laid over & including 10 mm thick screed base in CM 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, grinding and polishing to yield mirror finish with machine complete all as specified. |
| 76 | M&L for Machine Pressed precast concrete interlocking paver block any shape and size M-40 Grade, 80mm thick confirming to IS-15658-2006 with grey cement and pigments, top 6-8mm thickness gloosy finish coloured, epoxy coated, complete all as specified & directed. Note:- Sand cushioning shall bve measured and paid for separately. |
| 77 | M&L for Hard core of gauge not exceeding 63mm, deposited, spread and levelled in layers not exceeding 15cm thick watered and well rammed to a true surface complete all as specified & directed. |
| 78 | M&L for 25 mm thick (average thickness) PCC 1:2:4, type B-0 using 12.5mm graded stone aggregates as in floor by maintaing required gradient/undulation, finished even and fair without using extra cement complete all as specified and directed. |
| 79 | M&L for 75 mm thick cement concrete type C-2, 1:3:6 (using 40mm graded stone aggregate) as in Sub-base to floor finishes, surface finished even and rough to receive top floor finish complete all as specified & directed. |
| 80 | M&L for 75 mm thick cement concrete type D-2, 1:4:8 (using 40mm graded stone aggregate) as in Sub-base to floor finishes, surface finished even and rough to receive top floor finish complete all as specified & directed. |
| 81 | M&L for rendering 15mm thick plaster in cement mortar 1:3 mixed with WPC applied on concrete surfaces on roof top whilst the concrete is green, finished even and smooth without using extra cement complete all as specified & directed.Note;- WPC shall be measured and paid separately as Supply only. |
| 82 | M&L for rendering 5mm thick plaster in cement mortar 1:3 on concrete surfaces as in ceilings , chhajja, projection and similar isolated concrete surfaces, finished even and smooth without using extra cement complete all as specified & directed.. |
| 83 | M&L for 15mm thick rendering in two layers (5mm thick in CM 1:4 over 10mm thick in CM 1:6) on brick work and concrete surfaces of wall, finished the surface even and smooth without using extra cement, mixing and including WPC @ 200ml/bag of cement complete all as specified and directed. |
| 84 | M&L for rendering 10 mm thick cement plaster in CM 1:6 on fair face of brick work or concrete surface, finished even and smooth without using extra cement complete all as specified & directed. |
| 85 | M&L for 15mm thick rendering cement plaster in CM 1:6 on brick work and concrete surfaces of wall, finished the surface even and smooth without using extra cement, mixing and including WPC @ 200ml/bag of cement complete all as specified and directed. |
| 86 | Taking down cement plaster and decayed concrete of any description, upto tripple storey of building, from roof projection, chajja etc and making good the decayed portion with cement mortar 1 :3 mixed with water proofing compound as per manufacturers instruction or PCC 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregate) including necessary form work and finally finished the surface with 15mm thick cement plaster in CM 1:3 complete all as specified and directed. |
| 87 | M&L for 75 mm thick cement concrete 1:3:6, type C1 (using 20mm graded agg) as in plinth protection finished even and smooth using extra cement.(incl necessary joint filling with mixture of paving bitumen & sand in 1:3) complete all as specified & directed. |
| 88 | M&L for Preparation of newly plastered surface of wall and applying two coat of oil bound distemper, white or tinted shade with and including priming surface with chalk whitening complete all as specified & directed. |
| 89 | M&L for preparing newly plastered surfaces of ceilings and applying three coats of white wash complete all as specified & directed. |
| 90 | M & L for three coat of white wash on newly plaster surface of wall including preparation of surface complete all as specified & directed |
| 91 | M&L for preparation new or previously untreated steel or iron surfaces of any description, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified & directed. |
| 92 | M&L for preparation of old painted steel or iron surfaces of any description, over 10 cm width or girth and applying two coats of synthetic enamel paint complete all as specified & directed. |
| 93 | M&L for two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces. complete all as specified and directed |
| 94 | M&L for PCC 1:2:4 type B-1 using 20mm graded crushed stone aggregate as in coping, bed plates benching, slightly rounded or chamferred angles and throating including necessary form work complete all as specified & directed. |
| 95 | M&L for complete removal of the existing roof treatment any nos of layers taken out membrane, PCC Padding/roof, tiles etc including grabbing up of tree roots complete all as specified and directed. |
| 96 | M&L for PCC 1: 1.5: 3, type A-0 using 12.5mm graded stone aggregates mixed with & including WPC @ 0.200ml/50Kg of cement as in levelling course, and finished even and fair without using extra cement complete all as specified and directed. |
| 97 | M&L for following Roof treatment complete all as specified and directed:- (a) Applying 1st course of 15 mm thick screed bed with cement mortar 1:4 over old concrete surface (b) Applying 2nd course of bitumenous primer @ 0.4 kg/Square Metre conforming to IS-3384 over screed bed.(c) Applying 3rd course of a coat of bonding material with blown type bitumen of grade 85/25 heating to working temperature of 180 centigrade and applied @ 1.2 kg/Square Metre.(d) Applying 4th course of APP (Atactic Polypropylene) modified polymeric 3mm thick, weight not less than 3.6 kg/Square Metre with 160 Grams/Square Metre non woven polyster made at center core reinforced laid with 75 mm side overlap and 100 mm overlap. The membrane shall be laid with LPG torch and overlap sealed and finished neat .(e) Applying 5th course of a coat of bonding material with blown type bitumen of grade 85/25 heating to a working temperature of 180 centigrade and applied @ 1.2 kg/Square Metre . (f) Applying a coat of bitumenous based aluminium paint as finishing coat. |
| 98 | M& L preperation of inaccessible roof surface by scrapping and properly cleaning the existing roof treatment in any number of layers upto original RCC roof top surafce. Apply first coat Fiber reinforced Elastomeric liquid water proofing membrane formulated with PU hybrid polymers and reinforcing acrylic fibres with sun reflective index(SRI) of 100-110 , hsving minimum elongation of 350% tensile strength of 2.9 Mpa and shall have cracks bridging ability upto 2.5mm and shall resisit 10 bars of hydrostatic pressure reduce surface temperatureuoto 10 degree celsius with 33% dilution of priming coat. Laying of fiber mesh of 0.3 mm thickness weave in leno pattern having 45 gsm/Sqm and pasting it properly iwith overlap of 50mm and aloow it toodry.Apply second of undiluted coat @4.5 Ltr/Sqm. Apply third and final co for 10mm thick cement rendering in CM 1:E168at undiluted @0.45 ltr/sqm. Aplly third and final coat [email protected]/Sqm as directed by Engr in Charge.(a) M&L for 10mm thick cement rendering in CM1:3 and finishing the surface even and smooth before application of priming coat |
| 99 | M&L for APP modified roof treatment over existing non-accessible RCC roof slab / chajjas / canopy / parapet wall, to be executed through approved applicator of the membrane manufactured with following specifications, complete all as specified and directed :-(a) Cleaning the top surface of RCC roofing properly with water.(b) Applying oil bound bitumen primer @ 0.30 Litre / Sqm, manufactured by the same agency as that of APP with a density 0.87-0.89 KG / Litre at 25 degree centigrade on prepared surface.(c) Laying of membrane not less than 3.0mm thick APP modified water proofing membrane weighing not less than 3.60 KG/Sqm reinforced with non woven polyster fiber weight not less than 160 Gms/Sqm using butane torch by torch application with 10cm overlap and 15cm end lap.(d) Top of membrane shall be provided with solar reflective bituminous aluminum paint @ 0.10 KG / Sqm as prescribed by manufacturer of membrane.(e) APP Membrane shall be stick inside parapet where available by chase cutting and sealed with PCC 1:2:4, type B-0. (f) Top of membrane shall be provided with solar reflective bituminous aluminium paint @ 0.1 Kg/Sqm as prescribed by manufacture of membrane. |
| 100 | S&F Wire netting made of stainless steel wire 0.71 mm dia with size of mesh 25mm fixed with tinned tacks of stainless steel wire staples complete all as specified and directed. |
| 101 | M&L for mild steel TMT bars,10 mm dia and over in reinforcement cut to length, bent to shape required incl bending spirally cranking, hooping for columns, hooking ends and binding with and incl mild steel wire (annealed) not less than 0.9mm dia or securing with clipscomplete all as specified & directed. |
| 102 | M&L for mild steel TMT bars, 8 mm dia in reinforcement cut to length, bent to shape required incl bending spirally cranking, hooping for columns, hooking ends and binding with and incl mild steel wire (annealed) not less than 0.9mm dia or securing with clipscomplete all as specified & directed. |
| 103 | Use and waste of form work to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete for rough finished surface complete all as specified and directed. |
| 104 | Use and waste of form work to sides of concrete chajjas for rough finished surfaces complete all as specified and directed. |
| 105 | Use and waste of form work to sides of concrete pillars, columns, piers, posts with rough finished surfaces complete all as specifiedand directed. |
| 106 | Use and waste of form work to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc.complete for rough finished surface of concrete complete all as specified and directed. |
| 107 | Use and waste of form work to soffits of suspended slabs such as roof slabs, floor slabs, landing and similar works not exc 20 cm wide and sides of PCC/RCC bands exc 10 cm but n.exc 20 cm wide with fair finished.complete all as specified and directed. |
| 108 | Use and waste of form work to edges of concrete flats, treads, bracks in floor, openings in concrete walls, floors and roofs n exc 20 cmwide and sides of RCC/PCC bands in walls, and similar work exc 10cm but nexc 20 cm, incl fair finished surface of concrete complete all as specified and directed. |
| 109 | M&L for RCC M-25 design mix (using 20 mm graded crushed stone aggregates) as in foundation, footings,plinth beams etc. complete all as specified and directed. |
| 110 | M&L for RCC M-25 design mix (using 20 mm graded crushed stone aggregates) as in beams, cantilever and lintets over 1.50 m span and shelves and like etc. complete all as specified and directed. |
| 111 | M&L for RCC M-25 design mix (using 20 mm graded crushed stone aggregates) as in slab supported on walls, beams,columns etc. complete all as specified and directed. |
| 112 | M&L for RCC M-25 design mix (using 20 mm graded crushed stone aggregates) as in chajjas etc. complete all as specified and directed. |
| 113 | M&L for RCC M-25 design mix (using 20 mm graded crushed stone aggregates) as in columns,etc. complete all as specified and directed. |
| 114 | M&L for Precast reinforced cement concrete 1:2:4 type B-1, using 20mm graded crushed stone aggregate as in cover slab set in CM 1:6 complete all as specified and directed. Note : (Reinforcement shall be measured and paid separately). |
| 115 | Supply only liquid water proofing compound complete all as specified & directed. |
| 116 | M&L for Cement concrete 1:5:10 type E-2 (using 40mm graded crushed stone aggregate) as in mass filling in sunken slab of toilets complete all as specified. |
| 117 | M&L for 15 mm thick plaster in CM 1:4 mixed with intergral water proofing compound @ 200ml per 50 kg of cement bag and applying 75 mm thick padding of PCC M-20 Nominal Mix (1:1.5:3) of using 12.5 mm crushed graded stone aggregate and coving at junction of wall and floor with same concrete mix, the surface shall then be cured and allowed to dry and applying Epoxy Resins Coating, polymer Modified Cementation coating like brush bond of frsroc, pedilite and bostic as per manufactures instruction both on floor as well as on wall complete all as specified and directed. |
| 118 | Surface excavation, n exc 30cm deep and averaging 15cm deep and getting out in hard/dense soil complete all as specified and directed. |
| 119 | M&L for PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in foundation filling and mass concrete complete all as specified & directed. |
| 120 | M&L for rendering 15mm thick plaster in CM 1:4 on brick work and concrete surfaces of wall, finished the surface even and smooth without using extra cement, mixed with or without WPC, complete all as specified and directed. Note:- WPC, if mixed, shall be measuted and paid for separately as 'Supply only' |
| 121 | Dismantling plain or corrugated AC sheeting any gauge, thickness including ridges, valleys etc . Complete all as specified and directed. |
| 122 | S&F Pre-painted galvatume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, Chhaja, etc fixed with self tapping screws complete all as specified & directed. |
| 123 | S&F Pre-painted galvatume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, Chhaja, etc fixed with self tapping screws complete all as specified & directed. |
| 124 | S&F Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates Fe 290W Gde E-165 complete all as specified and directed |
| 125 | Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. complete all as specified & directed. |
| 126 | M&L for point wiring for one light/fan/bell point controlled with one switch with PVC insulated fire retardant low smoke multistranded copper conductor cable of 1.5 sqmm in and including PVC concealed non metallic conduit (ISI Marked) medium grade not less than 20 mm dia with all accessories and including pressed steel sunken terminal boxes (for mounting switches / regulators/socket /bell push etc ) made of not less than 16 gauge MS sheet and 6 cm depth covered with 3mm thick laminated bakelite sheet fitted with brass screw and cup washers and drawing 1.5 sqmm PVC insulated fire retardant low smoke multistranded copper conductor cable as earth continuity wire in green colour connected to common earth dolly and each terminal box/fitting including cutting chases to wall,making good the disturbed surfaces to match with the existing complete all as specified and directed by Engr-in-Charge (Phase Neutral and earth wire shall be provided in standard colour code R,Y,B for phase, Black for neutral green for earth wire). Note :In ceiling Portion surface conduit wiring shall be carried out complete all as specified & directed. |
| 127 | All as per description of serial item No. 180 here in before but for one 5 pin socket out let 5/6 Amps on same board with other switches. |
| 128 | All as per description of serial item No. 180 here in before but for one 5 pin 6 amps socket point controlled by one switch 6 amps on independent board. |
| 129 | All as per description of serial item No. 183 here in before but with 2.5 sqmm FRLS cable PVC insulated unsheathed multistrand for 2 in 1, 15/16 amp multipurpose socket outlet/metal plug top including 2.5 sqmm FRLS PVC insulated copper wire for earth continuity on independent board complete. |
| 130 | M&L for modular point wiring for one light/fan/bell point controlled by one switch complete with 1.5 Sqmm multistranded FRLS PVC insulated unsheathed, FRLS, multistranded copper conductor cable 1100 volts grade (red, yellow & blue) in and including medium duty non metallic rigid PVC concealed conduit 20 mm dia including conduit accessories like bends, tees junction boxes etc fixed concealed/recessed in wall or ceiling etc including 1.5 Sqmm single core FRLS PVC (green) insulated unsheathed multi stranded copper conductor 1100 Volts grade as earth continuity wire connected to earth dolly matching with surrouding with modular sunken steel boxes zinc oxide plated of suitable size including modular sheets of suitable module and back plates etc. complete all as specified and directed.Note: The unit rate quoted include the cost of cutting chases in surfaces for conduits and fixing of sunken boxes and making good the distrubed surfaces to match the existing surfaces. |
| 131 | All as per description of serial item No. 180 here in before but for one 5 pin socket out let 5/6 Amps on same board with other switches. |
| 132 | All as per description of serial item No. 180 here in before but for one 5 pin 6 amps socket point controlled by one switch 6 amps on independent board. |
| 133 | All as per description of serial item No. 183 here in before but with 2.5 sqmm FRLS cable PVC insulated unsheathed multistrand for 2 in 1 15/16 amp multipurpose socket outlet/metal plug top including 2.5 sqmm FRLS PVC insulated copper wire for earth continuity on independent board complete. |
| 134 | All as per description of serial item No. 183 here in before but with 4 sqmm FRLS cable PVC insulated unsheathed multistrand for 2 in 1 15/16 amp multipurpose socket outlet/metal plug top including 4 sqmm FRLS PVC insulated copper wire for earth continuity on independent board complete. |
| 135 | S&F Switch piano flush button single pole one way 6 Amps 240 volts with polycarbonate body complete all as specified and directed. |
| 136 | S&F modular switch, one module, 1 way, 10 Amps 240 volts complete all as specified and directed. |
| 137 | S&F modular socket 6A, 240 volts 2 & 3 pin, 2 Module complete all as specified and directed. |
| 138 | S&F modular switch, one module, 1 way, 16 Amps 240 volts complete all as specified and directed. |
| 139 | S&F modular socket, 6A & 16A, 240 volts, 2 & 3 pin, 2 Module complete all as specified and directed. |
| 140 | S&F multi purpose socket outlet for 2 & 3 pin, 6A, flush type complete all as specified and directed. |
| 141 | S&F socket outlet 2 in 1, 5 pin, 6 and 16 Amps , flush type, single pole, one way, 230Volts complete all as specified and directed. |
| 142 | S&F switch piano, flush type, single pole, one way, 16 Amps 230 Volts complete all as specified and directed. Please Enable Macros to View BoQ information |
| 143 | S&F switch piano, flush type, single pole, one way, 16 Amps 230 Volts complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 18, 2026
11:30 IST
Tender Published
Tender notice published.
TodayAug 07, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 20 daysAug 17, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 30 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender