Tender For Interior Development Works Of Archaeological Museum, Kondapur (Phase-1)- Execution Of Work
Tender Value
40.86 Lakhs
Estimated cost
Bid Submission
06 Aug 2026
18 days left
EMD
1.02 Lakhs
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Hyderabad → Telangana
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Interior Development Works Of Archaeological Museum, Kondapur (Phase-1)- Execution Of Work
BOQ
| Sl. No. | Item Description |
| 1 | Name of the Monument / Site: Archaeological Museum, Kondapur |
| 2 | Type-1 Display Case – Continuous C-Shaped Linear Display(18m span, 2.2 m Height) Fabrication, supply and installation of continuous U-shaped museum-grade display case having an 18-meter horizontal run, comprising bottom pedestal of 0.8 m height made using MS armature of 25mm square pipe, braced with channels, angle sections, stiffeners, plates and anchors. Pedestal externally finished with 18mm exterior grade MDF(off-gassing type) with 1mm approved laminate. Above pedestal, vitrines fabricated using 10–12 mm laminated toughened extra-clear glass (5+5+1.5 PVB interlayer), height 1.4 m, fixed with engineered-wood runners (50×100 mm), powder coated brass fittings, silicone sealing, and concealed fixing channels. All joints polished and ground flush. Includes LED COB track lighting above as per exhibit needs. Complete with graphical vinyl labels, cleaning, protection and testing. |
| 3 | Type-2 Display Case – Freestanding Floor-to-Ceiling Unit (13 sqm pedestal area + 2 sqm vitrine) Providing and installing a full-height freestanding display case with MS frame built-up structure from floor to ceiling, integrating pedestal opaque surfaces (13 sqm) using 18mm MDF/off-gassing board with 1mm laminate finish . Vitrine area of 2 sqm executed with 10–12 mm laminated toughened extra-clear glass supported on MS channels with brass hardware. Includes sealing, gasket work, anti-vibration pads, service routing, WPC/HDHMR internal carcass as required, and LED museum lighting integrated on the top frame. Vinyl-printed graphics included |
| 4 | Type-3 Display Case – Wall-Extended Freestanding Vitrine Fabrication and installation of a wall-projecting display case having 10 mm thick toughened glass mounted vertically, supported on top and bottom via corian/exterior grade MDF pedestals fixed on an MS armature. Pedestal includes WPC backing where needed. MS supports fabricated with welded/bolted construction, zinc chromate primed and enamel-painted. Vitrine area approx. 6 sqm. LED strip (4000K) and local lighting integrated. Vinyl ID tags included |
| 5 | Type-4 Display Case – Freestanding With Base Platform + Dual Vitrine System (10 sqm) Providing, fabricating and installing a freestanding dual-vitrine assembly projecting from the wall and anchored to MS steel structure. Includes base platform finished in laminate/CNC-cut WPC, two vitrines made from laminated toughened extra-clear glass fixed to MS runners with powder-coated brass fittings. Each vitrine fitted with internal object mounts (museum-grade, non-off-gassing). Approximate combined area 10 sqm. All lighting, labels, silicone sealing and finishing included |
| 6 | Type-5 Display Case With 20 Object Mounts + Glass Top (0.8 m height) Fabrication of 0.8 m high display pedestal with provision for 20 museum-grade mounts on top surface. Pedestal finished in 18 mm exterior-grade MDF with Laminate. Protective cover in 10–12 mm laminated toughened extra-clear glass fixed using brass hardware on engineered-wood runners. Includes internal MS reinforcement, WPC where necessary, silicone sealing, and labels.(actual quantity may vary as per site condition) |
| 7 | Diorama Circular Pedestal + Model (1.2 m dia pedestal + 2 sqm model) Providing and installing circular pedestal of 1.2 m diameter and 0.8 m height using MS armature + Corian cladding. Top platform supports a 2 sqm terrain/landform model finished using FRP, textured paint, and pigment shading. Includes protective clear coat, anchoring, and vinyl labels. |
| 8 | Infographic Panel With Integrated Mini Display Case (0.25×0.16×0.44 m vitrine; 2.5 sqm panel) – Fabrication and installation of infographic panels 2.5 sqm each, with an embedded mini-display case of size 25×16×44 cm using 11.5 mm laminated toughened glass fixed onto an MS and WPC sub-construction. Panel clad with 8 mm WPC + vinyl graphic print (80–100 micron, UV printed, matte/texture). Includes all MS support, leveling, fixing hardware and finishing. Six numbers |
| 9 | Relief Mural Panel (6 sqm) – Muddy-Tone Excavation Site Theme Providing and installing 6 sqm FRP/WPC/HDHMR-backed relief mural mounted on MS framing, representing excavation site textures in muddy-tone paint. Includes sculpting, texturing, priming, and protective topcoat. Anchored using Hilti anchors and concealed fasteners. Includes infographic vinyl as required. |
| 10 | Wayfinding & Signages – Design, Production & Installation (Complete System) Providing, designing, fabricating and installing a complete wayfinding and signage system across the facility including directional signs, informational signs, identification markers, gallery entry signs, safety signage, floor-mounted units and wall-mounted panels. Signage system to be developed with cohesive visual language in accordance with the approved design guidelines and graphic standards. |
| 11 | Infographic Panel – MS 25mm Pipe Support + 8mm WPC + Vinyl (1 sqm each) Fabrication of infographic display panels approx. 1 sqm each using MS 25mm pipe support grid, clad with 8 mm WPC sheets, finished with 80–100 micron vinyl printed graphics. All cutting, drilling, fixing hardware, primer + enamel on MS frame included. Ten units |
| 12 | Overlapping Toughened Glass Coin Display (2 sqm) Providing and fixing two vertical toughened or plexi glass panels (10–12 mm thick), overlapped with 1 cm spacing for coin insertion/display. Mounted on MS armature with off-gassing HDHMR/MDF top and bottom supports. Total display area approx. 5 sqm. Glass edges polished, joints sealed, and hardware in brass/SS. Each independant coin to have rotating glass cases of plex iglass extendiong 2.5 cm from their diameter and covering on either sides withh pivots |
| 13 | Curved Timeline Wall – 16 sqm Construction of a curved timeline wall using flexible exterior-grade board cladding on MS armature framework. Total area approx. 16 sqm. Includes 8 mm WPC + vinyl info graphics on exterior face. All MS works fully primed and enamel-painted. Includes lighting interface and service passage routing |
| 14 | Linear Cuboidal Info graphic Panel – 10 m Long Fabrication of a long cuboidal panel (10 m length) using MS 25mm armature, enclosed by 18 mm exterior grade MDF on all sides. Top surface finished with vinyl-printed info graphic graphics. Joints filled and finished to form a continuous monolithic surface. Includes concealed supports, brackets, and leveling |
| 15 | Circular Ceiling Art Element – Backlit Acrylic + Metal Armature Supply and fixing of circular ceiling-mounted artwork using MS armature of 25mm pipe, shaped using rolled circular forms, suspended with adjustable hangers. Backlit acrylic sheet (3–6 mm) with artwork printed on translucent media. Includes LED strip lighting (4000K), wiring routing, power supply, and mounting hardware. Complete as per design |
| 16 | Barisol Artwork Light From Ceiling (2 sqm) Providing and installing a 10 sqm Barisol-style artwork panel suspended from ceiling using MS armature and aluminum profiles. Includes backlit diffusers, LED modules, and graphic artwork printed on fabric/acrylic depending on design. All accessories, wiring, termination and testing included |
| 17 | MEP and Museum Lighting Works – Complete Installation Providing, supplying, installing, testing, and commissioning of all mechanical, electrical, plumbing for the museum, including exhibits, dioramas, display cases, wall panels, and visitor circulation areas including electrical wiring, concealed conduits, distribution boards, MCB, isolators, power routing, switch gear, junction boxes, cable management, earthing, terminations, load balancing and testing commissioning. Works to be executed as per approved drawings, design intent, and ISI standards(LS) |
| 18 | Providing, supplying, installing, testing, and commissioning of complete museum lighting system including hanging LED lights (2m wire, 4000K, 12W COB track spot, CRI>90, beam 45°, antiglare, powder-coated aluminum), track channels (2×2m, copper wiring, supports, clamps), LED strips in aluminum profiles for display cases, dioramas, timeline walls, fresco illumination (IP68 where required), wall washers (NW/WW), and backlit acrylic/glass panels. Complete with MS supports, concealed/surface wiring, DB connections, earthing, leveling, alignment, illumination testing, and integration with exhibits. Materials ISI certified, LED brands Cree/Litch Lux/Arkos/O-M, wiring FRLS/HF copper, switches/sockets Havells/Schneider/Anchor. Works executed as per approved drawings, design, and engineer-in-charge instructions. (LS) |
| 19 | Providing, Supplying and fixing of self-adhesive vinyl graphics on panels, display cases, walls, or any approved surface, including 80-100 micron thick vinyl printed with inforgraphic or designed content using UV/eco-solvent printers, with glossy, matte or textured finish as per design. Work includes surface preparation, cutting, drilling, leveling, seamless joint finishing, and fixing with adhesive/hardware as required, complete with alignment to drawings and approved graphical content. Vinyl to be durable, high quality suitable for indoor exhibits, and executed as per engineer-in-charge instructions and approved prototypes.(ls) Level) after deductions Qty 1700.761- 450.328= 1250.433) Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 17, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 06, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 18 daysAug 07, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 19 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender