Tender For Renovation Of Barpathari Regulated Market For E-Nam Market Including Internal Electrification At Barpathari Under Rajnagar Agri. Sub-Division, South Tripura.
Tender Value
7.52 Lakhs
Estimated cost
Bid Submission
23 Jul 2026
0 days left
EMD
15044
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
tripura → Tripura
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Renovation Of Barpathari Regulated Market For E-Nam Market Including Internal Electrification At Barpathari Under Rajnagar Agri. Sub-Division, South Tripura.
BOQ
| Sl. No. | Item Description |
| 1 | Enam Market Barpathari |
| 2 | Half brick masonry work with first class bricks in superstructure up to floor five level including cost of all materials as required complete:- R.C.C Slab supported brick work :- RCC slab supported brick wall |
| 3 | Centering shuttering including struttings, propping etc. and removal of form work for: Suspended floors, roofs, landings, balconies and access platform with timber planks:- |
| 4 | Reinforcement for R.C.C. work including straightening,cutting, bending, placing in position and binding allcomplete above plinth level. : Thermo-Mechanically Treated bars of grade Fe-500D or more |
| 5 | Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto floor five level excluding the cost of centring, shuttering, finishing and reinforcement. |
| 6 | 12 mm cement plaster of mix : Cement mortar 1:4 (1 cement : 4 fine sand) |
| 7 | 6 mm cement plaster of mix :Cement mortar 1:3 (1 cement : 3 fine sand) |
| 8 | Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mmhigh having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : |
| 9 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS : 1285, fixing with dash fasteners of required dia and size, including necessary filling up of gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawing and the direction of Engineerincharge. (Glazing and paneling and dash fasteners to be paid for separately) :-For fixed portion of approved quality:-16.1.1.1 Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15). |
| 10 | For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and makingprovision for fixing fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately ):-16.1.2.1 Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodiccoating of grade AC 15). |
| 11 | Providing and fixing 12 mm thick prelaminated three layer medium density (exterior grade ) particle boardgrade-I, type II conforming to IS : 12823 bonded with phenol formaldehyde synthetic resin, of approved brand and manufacture in panelling fixed in aluminium doors, windows, shutters and partition frames with C.P. brass / stainless steel screws all complete as per architectural drawing and the direction of Engineer-in-charge :- Prelaminated particle board of approved quality with decorative lamination on one side and balancing lamination on other side |
| 12 | Providing and fixing glazing of approved quality in aluminium doors, windows, ventilator, shutters andpartition etc. with EPDM rubber / neoprene gasket etc. complete as per architectural drawing and the direction of Engineer-in-charge (Cost of snap beading shall be paid in basic item) :-With float glass panes of 4.0 mm thickness ( weight not less than 10.0 kg / sqm ) |
| 13 | Providing and fixing gang saw cut of approved thickness mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base of cement mortar 1:4 ( 1 cement : 4 fine sand ) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing , curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels Area of slab over 0.50 sqm |
| 14 | Providing edge moulding to approved thickness marble stone counters, vanities etc. including machine polishing to edge to give high gloss finishetc. Complete at all levels as required as per design approved by the Engineer-in-charge: |
| 15 | Providing and laying 1st class quality vitrified floor tiles in different sizes (thickness to be specified by themanufacturer) with water absorption less than 0.08% and conforming to IS: 15622 - 2017, of approved make, in all colours and shades, laid over 20mm thick cement mortar 1:4 (1 cement : 4 fine sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc. all complete as per direction of the Engineer-in-charge. Soluble Salt Stainfree vitrified tiles (Glossy)Size of tile 600 mm x 600 mm |
| 16 | Chipping of unsound/weak concrete material from slabs, beams, columns etc. with manual Chisel and/ or bystandard power driven percussion type or of approved make including tapering of all edges, making squareshoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushesetc. and disposal of debris for all lead and lifts all complete as per direction of Engineer-In-Charge. 25 mm average thickness |
| 17 | Providing, mixing and applying SBR polymer (of approved make) modified Cement mortar in proportionof 1:4 (1 cement: 4 fine sand with polymer minimum 2% by wt. of cement used) as per specifications and as per direction of the Engineer-in-charge. Note: Measurement and payment: The pre-measurement of thickness shall be done just after the surface preparation is completed and Payment under this itemshall be made only after proper wet curing has been done and surface has been satisfactorily evaluated bysounding / tapping with a blunt metal instrument and/or the 75mm size cube crushing strength at the end of 28 days to be not less than 30 N/ mm2) 25 mm average thickness in 2 layers. |
| 18 | Providing and fixing 1st class quality ceramic glazed wall tiles conforming to IS : 15622 - 2017 (thickness to be specified by the manufacturer) of approved make in all colours, shades of any size as approved by Engineer-incharge in skirting, risers of steps and dados, laid over 12 mm thick bed of cement mortar 1 : 3 (1 cement : 3 fine sand) jointed with ordinary cement slurry including pointing with white cement mixed with pigment of matching shade etc. all complete as per direction of the Engineer in-charge |
| 19 | Providing and fixing aluminium tubular handle bar of 32 mm outer dia, 3.0 mm thick and 2100 mm long withStainless Steel screws etc. of approved quality complete as per direction of Engineer-in-charge:- Polyester powder coated aluminium minimum thickness 50 micron |
| 20 | Providing and fixing white vitreous china laboratory sink with C.I. brackets, C.P. brass chain with rubberplug 40mm C.P brass waste and 40mm C.P. brass trap with necessary C.P. brass unions complete including painting of fittings and brackets, cutting and making good the wall wherever required : Size 600x450x200mm |
| 21 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. 40 mm dia |
| 22 | Providing and fixing brass bib cock of approved quality : 15 mm nominal bore |
| 23 | Providing and fixing brass stop cock of approved quality : 15 mm nominal bore |
| 24 | Applying priming coat [Payment shall be made after submission of Test Certificate issued by theManufacturer] : With ready mixed Pink or Grey primer of approved brand and manufacture on wood work ( hard & soft wood ). |
| 25 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an evenshade [Payment shall be made after submission of Test Certificate issued by the Manufacturer]: 12.60.1 Two or more coats on new work over an under coat of suitable shade with ordinary paint (primer) of approved brand and manufacture |
| 26 | Distempering with 1st quality washable acrylic distemper of approved brand and manufacture and ofrequired shade on old work ( one or more coats ), to give an even shade as required complete as perdirection of the Engineer in charge. |
| 27 | Providing and laying in position cement concrete of specified grade excluding the cost of centring andshuttering - -All work upto plinth level: 1:2:4 ( 1 Cement: 2 fine sand : 4 graded well burnt brickaggregate 20 mm nominal size) |
| 28 | Wiring for light / fan / exhaust fan / call bell point with 2 x1.5 sq. mm pvc insulated Copper conductor cable (FR) in pvc casing and capping complete with 6/10 amps modular type switch, cover plate, surface modular switch board including connection etc as required:- Short Point :- |
| 29 | Wiring for light / fan / exhaust fan with 2 x1.5 sq. mm pvc insulated Copper conductor cable (FR) in pvc casing and capping complete with 6/10 amps modular type switch, cover plate, surface modular switch board inc. connection etc as required:- b) Medium point:- |
| 30 | c) Long point:- |
| 31 | Providing and fixing of 3 pin 5/6 amps plug point with Piano type 5/6 amps switch and socket with cover plate including connection with 2x1.5 sq. mm PVC insulated Copper conductor cable (FR) on PVC switch board, earthling the 3rd pin etc. as required. |
| 32 | Providing and fixing of 3/6 pin15/16 amps plug point with piano type 15/16 amps switch and socket including connection with 2x2.5 sq. mm PVC insulated Copper conductor cable (FR) on switch board, earthing the 3rd pin etc. as required |
| 33 | Wiring for Circuit/Sub-main wiring with the following sizes PVC insulated copper conductor cable (FR) in PVC casing capping etc. as required:- a) 2 X 1.5 sqmm |
| 34 | 3 X 1.5 sq mm |
| 35 | 2 X 2.5 sq mm |
| 36 | c) 2 x 4.0sqmm |
| 37 | 4 X 6 sq mm |
| 38 | Wiring for Circuit /Sub-main with the following sizes of PVC insulated Copper conductor cable (FR) in existing PVC casing capping / conduit in recess /surface including connection etc. as required:- 1 X 1.5 sq mm |
| 39 | 1 x 2.5 sq mm |
| 40 | 1 X 4 sq mm |
| 41 | Supplying and laying of the following sizes XLPE insulated PVC sheathed un-armoured cable with necessary connection etc as required 3 core 4 Sq mm aluminium conductor un-armoured cable |
| 42 | 4 core 4 Sq mm copper conductor un-armoured cable |
| 43 | Supplying and fixing of the following sizes PVC conduit on surface with all accessories etc. as required. 19/20 mm dia |
| 44 | Supplying and fixing of the following PVC casing capping with all accessories etc. as required. 32mm x 12mm |
| 45 | Supplying and fixing of the following sizes plastic (on surface) modular switch boards with modular cover plates etc. as required. 2 module Plastic switch board:- |
| 46 | 3 module Plastic switch board:- |
| 47 | 6 module Plastic switch board:- |
| 48 | Supplying and fixing of Copper terminal ends (LUGS) - long barrel of following sizes. 2.5 sq mm |
| 49 | Supplying and fixing of Copper terminal ends (LUGS) - long barrel of following sizes: - 4 sq mm |
| 50 | 6 sq mm |
| 51 | Supplying and fixing of the following electrical accessories including necessary connection etc. as required. 5 step Modular fan regulator (2M) |
| 52 | 32 amps 1-way DP switch (2M) |
| 53 | 3 pin 6/10 amps socket outlet (2M) |
| 54 | 3/6 pin 20 amps socket outlet (2M) |
| 55 | Angle/batten holder |
| 56 | 3 mm thick bakelite sheet |
| 57 | Blank Plate |
| 58 | 25 mm dia. Heavy PVC gland (LMR) |
| 59 | 25 mm dia. Heavy PVC flexible Pipe (LMR) |
| 60 | 16 amps power plug top |
| 61 | 32 amp DP Kitkat switch |
| 62 | Supplying and installation of Bus bar chamber of the following ratings and sizes made of steel sheet enclosure with all accessories including necessary connection etc. as required:- 32 amps 240 volts two strip Copper busbar chamber (LMR) |
| 63 | Supplying and installation of Switch disconnector fuse unit (main switch) of the following ratings with all accessories in existing panel board including necessary connection etc. as required:-63 amps 240 volts DP main switch (rewireable) |
| 64 | Supplying and installation of rewireable fuse unit (kitkat) of the following ratings in existing panel board including necessary connection etc as required:- 63 amps kitkat porcelain fuse unit with base(rewireable) |
| 65 | Supplying and installation of powder coated steel sheet enclosure (MCB DB) suitable for 240/415 volts MCB/Isolator (SP/SPN/DP/ TP/ TPN/FP) complete with necessary bus bar, neutral link, earth bar etc i/c connection as required. 4 way SPN MCB DB (double door) |
| 66 | (2+10)/12 way SPN MCB DB (double door) |
| 67 | Supplying & installation of 10 KA breaking capacity, B/C curve MCB of following ratings in the existing MCB DB including connection as required:- 6 to 32 amps SP MCB:- |
| 68 | Supplying & installation of isolators of following ratings in the existing MCB DB including connection etc as required:- 100 amps FP isolator |
| 69 | Supplying & installation of isolators of following ratings in the existing MCB DB including connection etc as required:-63 amps DP isolator:- |
| 70 | Supplying and fixing of MS frame made of (25mm x 25mm x 5mm) MS angle with necessary support by (40mm x 6mm) MS flat and 12 mm thick marine plywood on top, grouted on wall with 4 nos legs (25mmx25mmx5mm MS angle 20 cm long) finished with red oxide and 2 coat synthetic enamel paint including necessary cc work, mending the damages & painting etc as required:- |
| 71 | Supplying and fixing of following LED luminaries in powder coated die cast housing complete with high efficiency polycarbonate diffuser and necessary connection etc. as required Surface mounted box type batten suitable for single 20 watt integrated LED tube lamp including 20 watt LED tube with integral driver and polycarbonate diffuser |
| 72 | 12 watt LED retrofit Lamp |
| 73 | Supplying and fixing of 36 watt outdoor LED street light fixture with integral driver and secondary lens (IP 66) including necessary connection etc. as required. |
| 74 | Supplying & fixing of 1200 mm sweep white color AC ceiling fan capacitor type double ball bearing complete with 300 mm down rod,canopies,shackles, 3 nos blades, including wiring the down rod with 2x1.5 sqmm PVC insulated Copper conductor cable(FR) (ISI marked) including necessary connection etc. as required. |
| 75 | Supplying & fixing of 1200 mm sweep white color AC ceiling fan capacitor type double ball bearing complete with 300 mm down rod,canopies,shackles, 3 nos blades, including wiring the down rod with 2x1.5 sqmm PVC insulated Copper conductor cable(FR) (ISI marked) including necessary connection etc. as required. 40mm dia |
| 76 | arthing with GI earth plate 600 mm x 600 mm x 3 mm thick i/c accessories and providing masonry enclosure with CI cover plate Size 12\\"x 12\\" having locking arrangement, along with 20 mm dia (medium gauge) watering pipe including CC work etc as required:- |
| 77 | Extra for using salt (5 kg) and charcoal (46kg) for plate earth electrode as required. |
| 78 | Earthing with 40 mm dia G.I earth pipe (medium gauge) ( above 4.5m long normal size) i/c necessary hole etc as required. |
| 79 | Providing and fixing / Drawing 4.06 mm dia (8 SWG) Copper wire on surface or in existing G.I / PVC pipe for earthing as required. |
| 80 | Supply and fixing of 25mm x 3mm GI strip on walls/ floor of the building for horizontal/ vertical network including necessary spacers and porcelain insulators at regular intervals. |
| 81 | Supplying of ‘U’ clamp made with 40mm x 6 mm MS flat and fixing with necessary fasten nuts including painting etc as required. |
| 82 | Supplying and fitting fixing of M.S(18 SWG) KIOSK (Size 1200mm length x 450mm width x Height 450m) fitted four side slope roof filled with 4 Nos. support of 40mm x 40mm (6mm thick) MS angle,1.00mtr length from the level of concrete base embedded in 1:2:4 cement concrete base ( Size 300mm x 300mm x 600mm) with proper locking arrangement and coated with anti corrosive paint( both inside and outside) in/c necessary position for fitting fixing of all electrical accessories wooden plank etc. complete in all respect as per direction of Engineer-in-charge. |
| 83 | Supplying & installation of 1.5 Ton AC including indoor and outdoor unit with all accessories including connection etc as required Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 17, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 23, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
TodayJul 24, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 1 dayTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender