Tender For Certain Bldgs Repairs To Roofing, Flooring, Joinery, Plumbing And Other B/R Works In Right Side Of Tain Bridge (North Zone) Under Age B/R Dett-A Naushera Garrison Of Ge 862 Ews
Tender Value
45 Lakhs
Estimated cost
Bid Submission
07 Aug 2026
21 days left
EMD
90000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Rajouri → Jammu and Kashmir
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Certain Bldgs Repairs To Roofing, Flooring, Joinery, Plumbing And Other B/R Works In Right Side Of Tain Bridge (North Zone) Under Age B/R Dett-A Naushera Garrison Of Ge 862 Ews
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of cement concrete (unreinforced) in ground floors and pavings not exceeding 15 cm thickness (below or above GL) and removing out side MD land on contractor own arrangement, complete all as specified and directed.Note:- Demolition includes any no of layers including overleaped tiles , stone etc during execution and no extra cost shall be borne by Govt exchequer. |
| 2 | Demolition of cement concrete of any description and in any position not otherwise specifically provided for, complete all as specified and directed. |
| 3 | Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed. |
| 4 | Dismantling of mild steel work of any description, complete all as specified and directed. |
| 5 | Dismantling of timber scantling 40 sq cm and over in section, in any position, complete all as specified and directed. |
| 6 | Taking down chowkhats or frames with shutters (without taking off shutters from the frames) of size n. exc 1.5 Sqm each, complete all as specified and directed.Note-: The rate inlcudes making good of surfaces w/o any extra cost to Govt. |
| 7 | All as per item No 6.00 here-in-before but exc 1.5 Sqm and n.exc 4 sqm each. |
| 8 | Taking down shutters of any description exc 1 sqm but n exc 2 sqm each, complete all as specified and directed. |
| 9 | Taking down door shutter of any desc exc 1 sqm but not exc 2 sqm and refixing in the same opening, complete all as specified and directed. |
| 10 | Taking down old ceiling board of any description and re fixing same opening after adjusting and repair of existing hangar wire and ceiling grid, complete all as specified and directed.Note: Contractor shall preserve all dismantleD ceiling board and grid in order to refix the same any damage shall be borne by contractor. |
| 11 | Taking down cement plaster on brick, stone or concrete surfaces including racking out joints hacking for key, scrubbing down with water etc, complete all as specified and directed.Note: The cost includes any thickness found during execution increased due overlaping of n no of layers of plaster , tiles, mosiac finish with out any cost to govt exchequer. |
| 12 | M&L for stone walling of random rubble masonry, uncoursed, well bonded, bedded and soilidly hearted, built in cement mortar (1:6) including demolition of old stone masonry, complete all as specified and directed. |
| 13 | M&L for brick work with sub class \\"B\\" bricks straight or curved on plan exc. 6m mean radius built in cement mortar 1:6 incl demolition of old brick work, complete all as specified and directed. |
| 14 | Extra over stone walling of any type of stone for hammer dressing to face stones and dressing of face beds with maximum depression on face from straight edge held against the dressed surface n exc 40 mm and joints, as specified, of random rubble walling, uncoursed or brought upto courses, complete all as specified and directed. |
| 15 | Formwork to sides and soffits of floor or roof beam, beam hunching, girders, lintel, cantilevers, shelves including suports, overhangs etc, complete all as specified and directed. |
| 16 | M&L for RCC 1:2:4 type B1 (using 20 mm graded stone aggregate) for Beams, cantilevers, bressumers, lintel over 1.5 m span including demolition of old RCC, complete all as specified and directed. |
| 17 | M&L for mild steel TMT bars 10mm dia and over , cut to length ,bend to shape required, including cranking ,bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified and directed. |
| 18 | All as per Item No 17.00 here-in-before but 5 mm dia and over upto and including 10mm dia in stirrups, spacers and binders. |
| 19 | M&L for 25 mm thick cement concrete type B-0, 1:2:4 (using 12.5mm graded coarse aggregeate) as in levelling course to floor finishes, complete all as specified and directed. |
| 20 | M&L for 15mm thick screed bed or bedding layer in cement mortar 1:4 for laying floor finishes, complete all as specified and directed. |
| 21 | M&L for vitrified tiles coloured 600x600mm and 8mm to 10 mm thick as in floors jointed in neat cement slurrry and pointed in white cement slurry to match the shade of existing, complete all as sepcified and directed. Note:The contractor shall have no claim on difference what so ever on shade /colour of tile. |
| 22 | All as per item No 21.00 here-in-before but on vertical surfaces. |
| 23 | M&L for non skid ceramic tiles (size of each tile exceeding 0.06sqm and not exceeding 0.11 sqm) 7mm thick laid and jointed with cement slurry (in portions) and pointed with coloured cement to match in floor, complete all as specified and directed. |
| 24 | S&F galzed ceramic coloured tiles as on vertical surfaces 300x600x7mm thick set and jointed in neat cement slurry (in portions) and pointed with white or colored cement to match, complete all as specified and directed. |
| 25 | S&F 18-20 mm thick machine cut kota stone slab (area of each slab not exceeding 0.27 Sqm except space constraint) in flooring laid and jointed with gray cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete including roughing the surface, complete all as specified and directed. |
| 26 | All as per item No 25.00 here-in-before but on vertical surfaces. |
| 27 | M&L for cutting to existing kota stone flooring including grinding with granite grinding stones (carborandom stone) including minor repairs and polishing to mirror finish complete, complete all as specified and directed. |
| 28 | M&L for granite 16-18 mm thick of any type work table rubbed and polised in steps, jambs, pillars, window cill, cooking platforms and like in cement mortar 1:4 including pointing cement mortar 1:2 using marble dust with admixture of pigments to match with shade of granite including demolition of old granite, complete all as specified and directed. |
| 29 | M&L for providing edge moulding to any thickness of marble/ granite stone of any descriptions including machine polishing the edge to give high glossy finish etc, complete all as specified and directed. |
| 30 | M&L for cement concrete (1:2:4) type B-0 (using 12.5mm stone aggregate) as in roof padding benching kerbs of mud stops, rounded or chamfered on edges including form work, complete all as specified and directed |
| 31 | M&L for water proofing treatment on non approachable / non accessible roof surface horizontal and vertical surfaces in following sequence through manufacturer / authorized applicator of the manufacturer, complete all as specified and directed:-(i) Taking down/removing existing treatment and cleaning properly with wire brushing etc, rabish off from the premishes (ii) 10mm thick plastering on roof surfaces in cement mortar 1:4 mixed with water proofing compound as per manufacturers instructions (iii) After drying concrete surfaces and apply a coat of bituminous primer @ 0.40 Kg/Sqm on the prepared surface of roof (iv) After the primed surface has dried, apply a coat of hoat blown bitumen 85/25 or equivalent viscosity grade @ 1.2 Kg /Sqm of the surfaces etc complete.(v) Laying unrolled over the bitumen coated surfaces polymeric water proofing membrane, of approved make standard weight not less than 3 Kg / sqm with 100 mm over laps shall be sealed by flame as per manufacturer instruction.(vi) Applying a coat of hot air blown grade bitumen of grade 85 / 25 @ 0.5 Kg / sqm duly sanded over polymeric membrane complete. (vii) provide final layer of two coats of aluminium paint over a coat of primer as per manufactue instructions. |
| 32 | M&L for PCC 1:3:6 type C0 (using 12.50mm graded stone aggregate) as in back filling of pressed steel door frames, complete all as specified and directed. |
| 33 | M&L for cement concrete type B1 1:2:4 (using 20 mm graded stone aggregate) in PCC blocks for holdfasts, benching, coping and the like including weathering, slightly rounded or chamfered angles, complete all as specified and directed. |
| 34 | S&F anodised aluminium for frame of door, windows (openable/ sliding), ventilators, Partitions, grills, chanels for sliding with one or more rebates including aluminum beading cleats jointing cleat for fixing etc, complete all as specified and directed. |
| 35 | S&F anodised aluminium door shutters, aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges 03 Nos, mortice lock- 1 No, floor door stopper 01 No, anodised aluminium snap beading, screws etc, complete all as specified and directed. |
| 36 | S&F customised aluminium anodised window and ventilator shutters fixed type , aluminium section weighting 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing aluminium snap beading screws etc, complete all as specified and directed. |
| 37 | S&F aluminium anodised window and ventilator shutters side hung type without sush bars, aluminium section weighting 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing aluminium snap beading screws, anodised aluminium fittings such as peg stays 150mm long (01 Nos ) hinges typr B-21 100 m long (2 Nos) suitable handle (01) Nos etc, complete all as specified and directed. |
| 38 | S&F in repair door closer hydraulically regulated, designation No.3 universal type, suitable for door shutters of 851 to 1000mm in width of weight between 61 to 80 Kg aluminium (extruded section) body complete as in any position, complete all as specified and directed.specified and directed. |
| 39 | S&F in repair door closer hydraulically regulated , designation No.3 universal type, suitable for door shutters of 851 to 1000mm in width of weight between 61 to 80 Kg aluminium (extruded section) body complete as in any position, complete all as specified and directed. |
| 40 | S&F in repair brass mortice lock four levers vetrical type size 100mm or above as directed in new or old position, complete all as specified and directed. |
| 41 | S&F in repair brass mortice lock four levers vetrical type size 100mm or above as directed in new or old position, complete all as specified and directed. |
| 42 | S&F in repair double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed in any position, complete all as specified and directed. |
| 43 | S&F of 1.25 mm thick pressed steel frame 125x60mm for doors with one or more rebates including supplying and fixing necessary fixing lugs. Hinges lock strike plate etc, complete all as specified and directed. |
| 44 | S&F of 1.25 mm thick pressed steel frame 105x60mm for doors with one or more rebates including supplying and fixing necessary fixing lugs. Hinges lock strike plate etc, complete all as specified and directed. |
| 45 | S&F second class hard wood 35mm thick plain framed, panelled shutter (two panel) with lock rail and panel of 9mm B.W.P commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS: 1003 (Part I), kiln seasoned and chemically pressure treated, complete all as specified and directed. |
| 46 | S&F 35mm thick 2nd class hardwood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain chamfered or rounded fitted with category and mitred beads for securing glass etc fitted to chowkhats for doors, etc complete size of member of shutter as specified in SSR Part -I, Sec 8, clause 8.20 (b), complete all as specified and directed. |
| 47 | S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain coloured PVC sheet, reinforced with MS square tube supplying and fixing in opening as per specification and drawing, complete all as specified and directed. |
| 48 | S&F factory made solid panel PVC shutter 30 mm thick (style) consisting of frame made out of MS tube for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip 20 mm width struck inside with solvent cement for style and plain colour PVC sheet for top rail lock rail and bottom rail on either side and as gap inserts for top and bottom rail paneling of plain, colour PVC sheet to be fitted in the MS frame welded/ sealed to the styles and rail with suitable PVC sheets beading and jointed together with solvent cement S&F in frame at site as per specification and drawing in SSR part-II, complete all as specified and directed. |
| 49 | S&F factory made MS tubular box type window of MS rolled steel section conforming to IS-1038 and shall be ISI marked manufactured by ISI approved manufacturer, openable frames shall be fabricated of sections as approved by Engr-in-Charge, corner welded to form a solid fused welded joint handles shall be of z section welded with openable frame box steel section used in outer frame shutter frame and central frame shall be ERW secton of 16 gauge with fixing lugs to be fixed as per provision of IS-1038 except that top lugs shall not be provided, all shutters of windows shall be provided with 4 Nos friction free hinges, 2 Nos 75 mm tower bolts to each leaf of window one at top and one at bottom welded on 3 mm thick steel sheet piece of suitable size which shall be in turn welded to z section of steel window to provide suitable arrangement of using tower bolt, glazed, gauged window, mild steel casement stays 300mm with hinged joint and two plates with studs complete all as specified and directed with all fittings and fixtures without glazing bars, including 3mm sheet glass, stainless steel wire mesh of 0.56 nominal dia and average width of aperature 1.18 mm, complete all as specified and directed.Note:- All as per Drg No- CEUZ /TD/ 1517/15 Sheet No-1/3,2/3,3/3. |
| 50 | S&F factory made MS tubular box type ventilators with of MS rolled steel section conforming to IS-1038 and shall be ISI marked manufacture by ISI approved manufacture, openable frames shall be febricated of section as approved by Engr-in Charge, complete all as specified and directed. |
| 51 | S&F in repair guard bars/ grills as specified in between glazed and fly proof window shutter (sand witching guard bars/ grill) as per drg No CEPZ/TD-325/07 dt 04.12.07 primer coated, complete all as specified and directed. |
| 52 | S&F 3mm thick sheet glass ordinary quality and glazing with oil putty in squares not exceeding 0.50 sqm in each pane including hacking out old broken glasses, complete all as specified and directed. |
| 53 | S&F American aluminium handles size 200 mm long fixed with stainless steel screws (ISI marked), complete all as specified and directed. |
| 54 | S&F extruded aluminium alloy handles size 100 mm fabricated type anodised (ISI marked), complete all as specified and directed. |
| 55 | S&F aluminium anodized barrel tower bolts 150 mm long of extruded section (ISI marked), complete all as specified and directed. |
| 56 | S&F extruded aluminium alloy handles size 150 mm fabricated type anodised (ISI marked), complete all as specified and directed. |
| 57 | M&L for 300mm MS ordinary rat tail rod pattern door springs (ISI marked) of approved make including roller and roller plate, complete all as specified and directed. |
| 58 | S&F 300 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy, complete all as specified and directed. |
| 59 | S&F stainless steel wire cloth 0.36 mm any position nominal dia of wire and 1.4 mm average width of aperture fixed with tinned tacks or galvanised wire staple, complete all as specified and directed. |
| 60 | S&F in repair stainless steel wire cloth, 0.36mm nominal dia of wire and and average width of aperture 1.4mm fixed with stainless steel wire staples, complete all as specified and directed. |
| 61 | S&F 250mm long mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed, complete all as specified and directed. |
| 62 | S&F 75mm long stainless steel butt hinges (ISI Marked), complete all as specified and directed. |
| 63 | S&F in repair door seal made of aluminium strip powder coated 20mm width and provided rubber/ cotton mat lining fixed with screws to door shutters upto 1m width opening complete all as specified and directed. |
| 64 | S&F in repair floor door stopper 150mm of aluminium alloy body and tongue, anodised, with hard drawn steel spring fixed in floor complete, complete all as specified and directed. |
| 65 | S&F in repair aluminium beading with rubber gasket of suitable size and thickness as required at site for fixing glass in aluminium door/ window, complete all as specified and directed. |
| 66 | S&F of 4mm thick designer ceiling board in ceiling fixed with screw as per manufacturers instructions, laid on hot dipped galvanised iron in post grid with 24mm wide T section exposed flanges which shall be powder coated white. The frame work shall comprise of main runner made from 0.33 mm thick galvanised steel sheet & of size 24 x 32 x 300mm spaced at 12 mm centres securely fixed to the structural soffits by approved hangers at 1200mm maximum centres, hangers of GI wire 4 mm dia to be fixed by approved rowl plug, level adjusters and screws etc. The last hanger at the end of each main runner shall not be greater than 450mm from adjustacent wall flush fittings of 1200 mm long screws Tee with (double stiching) to interlocked between main runners at 600mm centre to from 1200 x 600mm modules cross tee longer than 600 mm modules to be formed by fittings 600mm long cross tee, tee perimeter wall angle shall be of 0.45mm thick galvanised steel of size 19 x 19mm and 300 mm long of white colour all as per insturction including dismantling of existing ceiling of any type, complete all as specified and directed. |
| 67 | S&F solid PVC wall lining consisting of 5mm to 6mm thick coloured PVC sheet wood grain printed inclusive of solvent cement and fixing at site on PVC frame as per specification complete after dismantling of old unserviceable PVC lining with fillets, complete all as specified and directed. |
| 68 | S&F PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC frame as per specification, complete all as specified and directed. |
| 69 | S&F 5mm thick plain colour PVC sheet in strips & channel feathered at the edges for fixing on solid PVC wall lining, insulated PVC wall lining, and solid PVC partitions inclusive of solvent cement and fixing at site as in panels, complete all as specified and directed. |
| 70 | S&F in repair 5mm to 6mm thick hollow PVC wall panelling heavy duty coloured as approved by Engrs-in-Charge inclusive of fixing screw, corner beading all as per manufacturer instructions, complete all as specified and directed. |
| 71 | M&L for easing and adjusting aluminium door and window including refixing beading after replacement of defective portions such as door closer, aluminium handles, hinges, locks, new rubber gasket, aluminium beading, pre-laminated particles board, sheet glass etc, complete all as specified and directed.Note: Door closer, door spring, prelaminated particle board, sheet glass shall be measured and paid separately under respective item of schedule. |
| 72 | S&F in repair stainless steel curtain rod 25mm dia mild steel chromium plated fancy type with fixing brackets, at both ends as per requirement, complete all as specified and directed. |
| 73 | S&F in repair stainless steel balls, dooms, and knobs for curtain rods, complete all as specified and directed. |
| 74 | S&F rolled mild steel as in roof trusses (framed), purlines, rafters, crane gantries rails and fastenings and heavy brackets framing (beam, tee angle channel or fast sections) including distance pieces cleats etc conforming to Fe-290 Gde E-165, complete all as specified and directed. |
| 75 | S&F mild steel screw bolts exceeding 5cm length not exceeding 10cm length (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square dia of shank 11 to 15mm, complete all as specified and directed. |
| 76 | S&F (plain or chequered) channels, square cut or notched (oridinary and counter sunk) forming holes, w/o any attatchment, complete all as specified and directed. |
| 77 | S&F pre-painted galvalume zinc coating GI based high rib profile pattern steel sheet 0.50 mm thick (multi colour pattern as approved by GE) having tensile strength of 550 Mpa as in roof covering/cladding to wall , fixed with self tapping screws \\"L\\" or \\"J\\" hooks including dismantling of old sheet, complete all as specified and directed. |
| 78 | S&F pre-painted galvalume aluminium zinc coating GI based plain sheet 0.50mm thick (multi colour pattern as approved by GE) having tensile strength 550 MPa as in ridges, hips, valley gutters fixed with self tapping screws including side and end lap as per manufacturer’s instructions including dismantling of old sheet, complete all as specified and directed. |
| 79 | S&F of rotational moulded polythene water storage tank (cylindrical vertical with closed top) hoisted and fixed in position of 500 ltrs with and including tank nipple including dismantling of tank, complete all as sepcified and directed.Note: The water tank shall be double layer IS Marked duly embossed on face and weight as per IS Specifications. |
| 80 | S&F rotational moulded polythene water storage tank (cylindrical vertical with closed top) hoisted and fixed in position of 1000 ltrs with and including tank nipple including dismantling of tank, complete all as sepcified and directed.Note : The water tank shall be double layer IS Marked duly embossed on face and weight as per IS specifications . |
| 81 | M&L for disconnecting existing tanks 500 litres capacity , setting aside (or lowering if required) for repairs, cleaning and removing all scale and dirt etc and wahsing by detergent powder and also write date of cleaning and due date with black/ white marker from tanks and mouths of circulation pipes, and hoisting if required reconnecting and refixing of position and all fittings ie. PVC ball float valve, tank nipple necessary required fittings and replaced (if unserviceable) etc, complete all as specified and directed. |
| 82 | M&L for disconnecting existing tanks 1000 litre capacity , setting aside (or lowering if required) for repairs, cleaning and removing all scale and dirt etc and wahsing by detergent powder and also write date of cleaning and due date with black/ white marker from tanks and mouths of circulation pipes, and hoisting if required reconnecting and refixing of position and all fittings ie. PVC ball float valve, tank nipple necessary required fittings and replaced (if unserviceable) etc, complete all as specified and directed. |
| 83 | S&F in repair for ball valves suitable for 15mm bore iron pipe high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight 142 grams), complete all as specified and directed. |
| 84 | S&F in repair for ball valves suitable for 20mm bore iron pipe high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight 210 grams), complete all as specified and directed. |
| 85 | S&F 15mm bore galvanised iron GI tubing medium grade with all fittings such as bends, socket, tee, elbow, union, nipple, short pieces and fixed to walls, ceilings or laid in floors etc including taking down of old GI pipe, complete all as specified and directed. |
| 86 | S&F 20mm bore galvanised iron GI tubing medium grade with all fittings such as bends, socket, tee, elbow, union, nipple, short pieces and fixed to walls, ceilings or laid in floors etc including taking down of old GI pipe, complete all as specified and directed. |
| 87 | Fixing only 15mm bore galvanised iron GI tubing medium grade with all fittings such as bends, socket, tee, elbow, union, nipple, short pieces and fixed to walls, ceilings or laid in floors including taking down of old GI pipe, complete all as specified and directed. |
| 88 | Fixing only 20mm bore galvanised iron GI tubing medium grade with all fittings such as bends, socket, tee, elbow, union, nipple, short pieces and fixed to walls, ceilings or laid in floors including taking down of old GI pipe, complete all as specified and directed. |
| 89 | S&F in repair 15 mm bore gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed in new or old position, complete all as sepcified and directed. |
| 90 | S&F in repair 20mm bore gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed in new or old position, complete all as sepcified and directed. |
| 91 | S&F in repair waste cupling chromium plated 32mm bore size full threaded with 80mm height including all necessry washers, complete all as sepcified and directed. |
| 92 | S&F in repair 15mm bore fancy type pillar taps, cast copper alloy, with capstan heads, brass chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete, complete all as specified and directed. |
| 93 | S&F in repair bib taps 15mm bore chromium plated, fancy type, cast copper alloy with crutch, butterfly handle screw down, screwed for iron pipe or for brass, complete all as specified and directed. |
| 94 | S&F in repair for 15mm bib tap standard of PTMT of any colour high pressure screwed for iron pipe and fixed, complete all as specified and directed. |
| 95 | S&F in repair for 15mm bore angle/ stop valve, cast copper alloy screwed down, high pressure with crutch, or butterfly handle, chromium plated, screwed both ends for iron pipe or for unions and fixed, complete all as specified and directed. |
| 96 | S&F in repair for 15mm stop valve standard of PTMT of any colour high pressure screwed for iron pipe and fixed, complete all as specified and directed. |
| 97 | S&F in repair for 15mm bore stop valve (concealed type), cast copper alloy screwed down, high pressure with crutch or butterfly handle, chromium plated, screwed both ends for iron pipe or for unions and fixed, complete all as specified and directed. |
| 98 | S&F in repair for 15mm bore two way angle valve, cast copper alloy, fency type screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed, complete all as specified and directed. |
| 99 | S&F in repairs for CP Mixer for mixing hot and cold water for wash hand basin screwed down for 15mm pipe, complete all as specified and directed. |
| 100 | S&F in repair stainless steel soap dish holder fixed with and including SS screw and rowel plugs, complete all as specified and directed. |
| 101 | S&F in repair for stainless steel toilet paper holder, fancy type fixed wirth stainless steel screws/ rawl plugs etc, complete all as specified and directed. |
| 102 | S&F of stainless steel peg set with minimum 06 Nos of hooks mounted over 4mm thick stainless steel plate with and including screw and rowel plugs etc, complete all as specified and directed. |
| 103 | S&F in repair health faucet (ABS body) mild steel chromium plated suitable for 15mm dia pipe with 1.25 meter long flexible tube and ABS wall hook including making connections and fixed in position, complete all as specified and directed. |
| 104 | S&F in repair 32/40mm dia PVC waste pipe for WHB/sink /urinal complete all as specified and directed minimum weight 45 to 60 gms, complete all as sepcified and directed. |
| 105 | S&F in repair for PVC connection 15mm x 450mm including PTMT nuts at both ends screwed for iron pipe of 15mm bore, complete all as specified and directed. |
| 106 | S&F in repair 32mm waste fittings brass chromium plated for glazed ware basins, sink etc with long screwed shanks and fly nuts flange end bedded in red lead cement and other end fixed, complete all as specified and directed. |
| 107 | S&F in repair CP jet for EWC along with PVC connection complete all as specified and directed. |
| 108 | S&F in repair 40mm waste fittings brass chromium plated for glazed ware sink basin, with long screwed shanks and fly nuts flange end bedded in red lead cement and other end fixed, complete all as specified and directed. |
| 109 | S&F in repair plastic water closet seat cover, black/ white colour, closed pattern with flat bottom and cover and mild steel chromium plated aluminium hinging device for pedestral pattern WC, complete all as specified and directed. |
| 110 | S&F in repair viterous china wash down water closet pan (pedestal pattern), white (excluding flushing cistern, flush pipe, complete all as specified and directed. |
| 111 | S&F in repair WC Orissa pattern white with integral foot rest 580x440mm incuding PCC bedding in 1:2:4 type B-1 and making good disturbed floor connecting to tap and flush pipe, complete all as specified and directed. |
| 112 | S&F in repair vitreous China wash basin, white, flat back, size 550x400mm including waste coupling wate pipe and brackets, complete all as specified and directed. |
| 113 | S&F in repair water closet pedestal pattern (ONE PIECE) colour (as approved by GE) Make: {(CERA CAT PART No (EWC S1012135 and soft seat cover, B1540102 Twin flush cistern 2205/BT CRUSE)/ (Jaquar : LYS WHT-38751S250UFSMZ) or Kohler white Cat No K-21924X-S-WK), complete all as specifed and directed. |
| 114 | S&F in repair wash hand basin oval/ stretched obloid white 665x495mm, complete all as specified and directed.Make:- {(CERA CAT PART No (WHB-S2031032)/ Jaquar ACS-WHT-87701/ Kohler 25531W as approved by GE. |
| 115 | S&F in repair 15mm bore centre hole basin mixer with round spout with 450mm long copper pipes and brass nuts with out pop up, complete all as specified and directed.Make: {(Jaquar Cat No CON 167KNB )/ CERA (F1015451)/ Kohler 16231D-40}. |
| 116 | S&F in repair 15mm bore wall mixer with and including cups with telephonic shower arrangement for over head shower, complete all as specified and directed.Make: {(Jaquar Cat No CON 267KN)/ CERA (F1015414/ Kohler(Cat No 19561D)}. |
| 117 | S&F in repair 10 Litres capacity PVC valveless, syphonic action type, flushing cistern, low level, white with inlet, ball valve, float and handle including brackets, complete all as specified and directed. |
| 118 | S&F in repair viterous china urinal half stall type white including CP spreader holding screws, waster pipe etc, complete all as specified and directed. |
| 119 | S&F in repair sheet glass shelf assembly consisting of 5.5mm thick sheet galss shelf 12 cm wide with chromium plated bracket guard and railing 60cm long, fixing with stainless screws, complete all as specified and directed. |
| 120 | S&F in repair sheet glass corner assembly consisting of 5.5mm thick sheet galss corner size 300x300mm chromium plated bracket guard and railing , fixing with stainless screws, complete all as specified and directed. |
| 121 | S&F in repair 600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers, complete all as specified and directed. |
| 122 | S&F in repair stainless steel gratings of 100mm dia, fixed in repairs, complete all as specified and directed. |
| 123 | S&F in repairs PVC (SWR) floor trap with gratings including jointing with solvent cement 75mm dia complete, complete all as specified and directed. |
| 124 | S&F in repair towel ring of PTMT fixed with and including chromium plated brass screws and wooden/ plastic cleats, complete all as specified and directed. |
| 125 | S&F in repair tubular towel rail 20mm dia, D type, chromium plated 60cm long between flanges, complete all as specified and directed. |
| 126 | S&F in repair chromium plated shower roses with or without swivel joints, any size, including fixing to steel pipe or union, complete all as specified and directed. |
| 127 | S&F in repair 110mm bore PVC (SWR) pipe single socketed, in any length with rubber joints laid in floor/ground, complete all as specified and directed. |
| 128 | S&F in repairs PVC(SWR) pipes 110mm dia single socketed in any length with rubber ring joints fixed to walls, complete all as specified and directed. |
| 129 | S&F in repairs 75mm bore PVC (SWR) pipe single socketed, in any length with rubber joints laid in floor/ ground, complete all as specified and directed. |
| 130 | S&F in repairs 75mm bore PVC (SWR) pipe single socketed, in any length with rubber joints fixed to walls, complete all as specified and directed. |
| 131 | S&F PVC(SWR) bend any radius of 110mm bore jointed with solvent cement, complete all as specified and directed. |
| 132 | S&F PVC(SWR) junction double (single T) of size 110mm bore jointing with solvent cement, complete all as specified and directed. |
| 133 | S&F PVC(SWR) reducer 110mm to 75mm bore jointing with solvent cement, complete all as specified and directed. |
| 134 | S&F PVC (SWR) bend any radius of 75mm bore, complete all as specified and directed. |
| 135 | S&F PVC S trap 110mm bore (SWR) fixed in repairs and jointed, complete all as specified and directed. |
| 136 | M&L for providing 75mm cement concrete, type C-1, 1:3:6, (using 20mm graded stone aggregate) as in plinth protection, laid in slope 1:12 from outer edge of the wall, finished even and fair, laid in alternate bays including providing 6mm wide joints throughtout thickness of plinth protection in concrete bays and in between walling and plinth protection, joints filled mastic filling comprising of one part of heated bituminous 85/25 and 3 parts of sand (all by weight), complete all as specified and directed. |
| 137 | M&L for rendering 20mm thick in cement mortar (1:4) on stone masonry surface, finished even and smooth without using extra cement, complete all as specifed and directed.Note: No extra cost shall be claimed by contractor for plastering at any height above 3 mtr and any site where work is to be executed. |
| 138 | M&L for rendering 20mm thick in cement mortar 1:6 on stone masonry surface, finished even and smooth without using extra cement, complete all as specified and directed. |
| 139 | M&L for rendering 15mm thick in cement mortar 1:6 on brick masonry surface or concrete work, finished even and smooth without using extra cement, complete all as specified and directed. |
| 140 | M&L for rendering 15 mm thick in cement mortar 1:4 on brick masonry surface or concrete work, finished even and smooth without using extra cement, complete all as specified and directed. Note: No extra cost shall be claimed by contractor for plastering at any height above 3 mtr and any site where work is to be executed. |
| 141 | M&L for rendering 5mm thick in cement mortar 1:3 on concrete surface of ceiling/ facia, finished surface even and smooth without using extra cement, complete all as specifed and directed. Note:- No extra cost cost shall be claimed by contractor in respect of formwork/ scafolding and at any height and site where plaster is to be executed. |
| 142 | M&L for preparation of old decorated brick/ concrete plastered/ un-plastered surfaces of walls, pillars, cornices etc by brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and treating oil and greasy spots and applying two coats of exterior emulsion weather proof paint in two or more colour pattern over a coat of primer (multi clour pattern as approved by GE), complete all as specified and directed. |
| 143 | M&L for preparation of old decorated plastered surface of walls and applying one coat of oil bound distemper, complete all as specified and directed.. |
| 144 | M&L for preparation of newly plastered surfaces of any position/ wall and applying two coats of exterior weather proof paint (multi colour pattern as approved by GE) over a coat of alkali resistant primer, complete all as specified and directed. |
| 145 | M&L for preparation of newly plastered surfaces of walls and applying three coats of white wash, complete all as specified and directed. |
| 146 | M&L for preparation of new surfaces of wall and applying a thin layer of 2mm thick putty to give a uniform finish as approved by Engrs-in-Charge and required at site. |
| 147 | M&L for preparation of new plastered surface of walls and applying two coats of oil bound distemper, complete all as specified and directed. |
| 148 | M&L for applying two coats of synthetic enamel paint over a coat of pink primer on new or previously untreated wood and wood based surface including preparation,complete all as specified and directed. |
| 149 | M&L for applying one coat of synthetic enamel paint over on old wood and wood based surface including preparation, complete all as specified and directed. |
| 150 | M&L for preparation of new of previously untreated steel or iron surfaces of any description over 10 cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed. |
| 151 | M&L for preparation of old painted steel or iron surfaces of any description over 10cm width or girth not otherwise described and applying one coat of synthetic enamel paint, complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 17, 2026
11:30 IST
Tender Published
Tender notice published.
TodayAug 07, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 21 daysAug 11, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 25 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender