Tender For Maintenance Works Related To Flushing Of Various Borewells And Repair Of Pump,Motor, Starter And Allied Wks At Bdg Area, Engr Sqn, 2Asd, Under Aor Of Age (I) Nyoma.
Tender Value
7.87 Lakhs
Estimated cost
Bid Submission
06 Aug 2026
19 days left
EMD
16000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
nyoma → Jammu And Kashmir
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Maintenance Works Related To Flushing Of Various Borewells And Repair Of Pump,Motor, Starter And Allied Wks At Bdg Area, Engr Sqn, 2Asd, Under Aor Of Age (I) Nyoma.
BOQ
| Sl. No. | Item Description |
| 1 | Labour for lifting of submersible pump and motor along with flanged column pipe, submersible cable, safety rope etc from the existing bore well by using suitable T&P etc after disconnecting submersible cable from starter making necessary repairs by opening and renewal of parts as required including transportation to market and back for repair up to 10 HP capacity pumpset, complete all as specified and directed by Engr-in-charge. Note: Parts Renewed shall be measured and paid separately |
| 2 | S & F as in replacement following spares parts of deep well submersible pump set having discharge upto 25,000 gallon per hour multistage water lubricated type of capacity up to 10 HP, complete all as specified and directed by Engr-in-charge. |
| 3 | (i) Centrifugally casted cast iron bowl complete with gun metal bush of suitable size to match with existing pump shaft. |
| 4 | (ii) Gunmetal impeller close type with keys. |
| 5 | (iii) Cast iron discharge case with gun metal bush (Top Bowl). |
| 6 | (iv) Cast iron sanction piece (IP piece). |
| 7 | (v) Pump shaft made of antimagnetic stainless steel of existing size as per site requirement. |
| 8 | (vi) Rubber bush for intermediate bowl |
| 9 | (vii) Stainless steel sleeve required in between pump shaft and rubber bush. |
| 10 | (viii) Sand guard. |
| 11 | (ix) Gun metal ring for cast iron bowl. |
| 12 | (x) Oil seal for pump. |
| 13 | (xi) Stainless steel struts off size. |
| 14 | (xii) Cast iron non return valve suitable for pump. |
| 15 | (xiii) Stainless steel coupling for motor pump. |
| 16 | FOR MOTOR |
| 17 | (xiv) Gunmetal bush for motor. |
| 18 | (xv) Carbon bearing for thrust plate for motor. |
| 19 | (xvi) Stainless steel thrust bearing complete set suitable for motor. |
| 20 | (xvii) Stainless steel sleeve required in between rotor and bowel (bush) for motor. |
| 21 | (xviii) Sleeve suitable for oil seal of rotor. |
| 22 | (xix) Sand guard for motor. |
| 23 | (xx) Stainless steel strut for motor. |
| 24 | (xxi) Cast iron housing for motor end bush. |
| 25 | (xxii) Thrust bearing housing. |
| 26 | (xxiii) Cast iron connection piece for motor with sand guard. |
| 27 | Supply only the following items/spare parts suitable for star delta starter of capacity upto 10HP capacity dismantled/fixed under here in above complete all as specified and directed: - |
| 28 | (a) Fixed contact ‘A’ (Set of 24) |
| 29 | (b) Fixed contact ‘B’ (Set of 24) |
| 30 | (c) Moving contact ‘B’ (Set of 12) |
| 31 | (d) Oil dash pot assembly (Set of 03) |
| 32 | (e) Cam spring |
| 33 | (f) Lever spring |
| 34 | (g) Over load coil |
| 35 | (h) No volt coil 415 Volts AC |
| 36 | (j) Bore plate Bakelite |
| 37 | (k) Steam carrier assembly (Set of 03) |
| 38 | (l) Auxiliary switch |
| 39 | (m) RZ timer with coil & time delay relay of range 3 to 12 seconds |
| 40 | Dismantling carefully vertical turbine, centrifugal pump motor three phase, 415 volts, 50 Hz, 2860 RPM 15 HP of any make and model from site of installation, transporting the same to workshop, removing all burnt / worn out coils, cleaning of stator slots, insertion of insulating paper in the slots of appropriate size and rewinding with supper enameled copper wire ISI marked with existing size, applying two coats of insulating varnish including all winding materials, transporting back the same and reinstallation of the 15 HP motor, complete all as specified and directed by Engr-in-charge. |
| 41 | S & F as in replacement fully automatic citation DOL Starter in Sheet Steel Enclosure suitable for 30 HP, 3 phase , 50 Hz AC motor including M Contactor & Pneumatic Timers and making all electrical connections with appropriate size copper cable on existing panel, complete all as specified and directed by Engr-in-charge. Make Seimens, MEI Killburn |
| 42 | M&L for flushing of borewell complete by using 210 CMF compressor and heavy duty driller machine to deliver the high air pressure at the bottom of the bore well and cleaning/flushing the bore well till the water is become free from any type of mud,dust and clear for portable use, complete all as specified and directed by Engr-in-charge. |
| 43 | Lowering down of submersible pump set along with connected items such as column pipes ,submersible cable by using suitable T&P and reconnecting all electrical connections,commissioning & testing for 1up to 10 HP capacity pumpset, complete all as specified and directed by Engr-in-charge. |
| 44 | Supply and fixing MS column pipe heavy duty (ERW) of size100 mm with wall thicknes 5.04mm, length 3.0 mtr , both ends threaded with one socket confirming to IS 1239 (Part-I) 1979 incl painted with two coat of black bituminous paint over a coat of red oxide primer in internally & externally (suitable for drinking purpose), complete all as specified and directed by Engr-in-charge. Note :- Taking up of old coloumn pipe and lowering down of new column pipe shall be paid under respected item of BOQ |
| 45 | Supply and fixing MS column pipe heavy duty (ERW) of size 50 mm with wall thicknes 5.04mm, length 3.0 mtr , both ends threaded with one socket confirming to IS 1239 (Part-I) 1979 incl painted with two coat of black bituminous paint over a coat of red oxide primer in internally & externally (suitable for drinking purpose), complete all as specified and directed by Engr-in-charge. Note :- Taking up of old coloumn pipe and lowering down of new column pipe shall be paid under respected item of BOQ |
| 46 | Supply and fixing inreplacement of submersible pump 5 Hp ,(8-17) stage,discharge outlet size 50 mm, maximum discharge flow 100-500 LPM ,three phase,3000 rpm, 400V ,Suitable for 200 mm casing pipe, complete all as specified and directed by Engr-in-charge. Make- Kirloskar KS4G-5017 or equivalent |
| 47 | M&L for PVC insulated and sheathed multi standard 3 core 10 sqmm flat 1100 volts grade electric copper sumbersible cable, complete all as specified and directed by Engr-in-charge. |
| 48 | M&L for PVC insulated and sheathed multi standard 3 core 6 sqmm flat 1100 volts grade electric copper sumbersible cable, complete all as specified and directed by Engr-in-charge. |
| 49 | Demolishing the old unsv valve chamber and M&L for construction of valve chamber of size 900mm x 900mm x 1500mm in CM 1:6, depth of the chamber to be reckoned from the top of the PCC to top of the MS cover as 1.5 Mtr including MS sheet cover fabricated from 3mm thick MS sheet and frame of angle iron 40mm x 40mm x 6mm with all fixing and locking arrangement and painting two coats of synthetic enamel paint over a coat of red oxide on MS cover & frame including necessary excavation and earth work in any type of soil, returning filling and disposal of surplus soil to a distrance n.exc 50m, including 15mm thick plaster in CM 1:4 (both internally & externally), complete all as specified and directed by Engr-in-charge. |
| 50 | M & L for making a lorry filling point complete by RCC piller of size 45 cm x 45 cm x 3.5 mtr height with (1:2:4) type B1 using 20 mm graded stone aggregate alongwith Mild steel TMT bars 12 mm dia over cut to length ,bent to shape required ,including cranking ,bending spirally for hooping for columns hooking ends and binding with mild steel wire annealed and 8 mm to 10 mm dia cut to length , bent to shape required in stirrups,spacers and binders and binding with mild steel wire annealed not less than 0.9 mtr dia,or securing with clips,as in pillar,,columns including inserting Tee of 50 mm GI medium grade with 50 mm Gun metal gate valve alongwith suitable size 50 mm GI pipe (upto 3 mtr) medium grade and including hose pipe of 3 Mtr length one side flanged on pipe, complete all as specified and directed by Engr-in-charge. |
| 51 | Taking up / down old DI/GI/PP-R tubing connection including clearing (from trenches), complete all as specified and directed by Engr-in-charge of following size: |
| 52 | (i) 25 mm bore |
| 53 | (iv) 50 mm bore |
| 54 | Supply and fixing in replacement of 3-layer PP-R Polypropylene random copolymer concealed piper SDR 7.4 ((PN-16) VU stabilized and antimicrobial dusion welded having thermal stability for hot & cold water supply all PP-R plain & brass threaded polypropylene random fittings 50 mm outer dia with all fitting laid in trenches or fixed to walls and ceiling or laid in floor, complete all as specified and directed by Engr-in-charge. Make : SFMC or equivalent |
| 55 | Supply and fixing in replacement of 3-layer PP-R Polypropylene random copolymer concealed piper SDR 7.4 ((PN-16) VU stabilized and antimicrobial dusion welded having thermal stability for hot & cold water supply all PP-R plain & brass threaded polypropylene random fittings 25 mm outer dia with all fitting laid in trenches or fixed to walls and ceiling or laid in floor, complete all as specified and directed by Engr-in-charge. Make : SFMC or equivalent |
| 56 | M&L for Elestometric Nytral rubber insulation to PP-R pipes suitable for 50 mm outer dia 22/19mm thick with chiken wire mesh wire netting 50 mm gauge, 40mm mesh with 0.01mm aluminium foil including jointing and fixing material such as solvent adhesive SR-998, complete all as specified and directed by Engr-in-charge. |
| 57 | M&L for Elestometric Nytral rubber insulation to PP-R pipes suitable for 25 mm outer dia 28/19mm thick with chiken wire mesh wire netting 25mm gauge, 20mm mesh with 0.01mm aluminium foil including jointing and fixing material such as solvent adhesive SR-998, complete all as specified and directed by Engr-in-charge. |
| 58 | Supply and fixing in replacement of PP-R gate valve (brass insert) for 50 mm outer dia pipe as per requirement of the site, complete all as specified and directed by Engr-in-charge. . Make : SFMC/Prince or equivalent. |
| 59 | Supply and fixing in replacement of PP-R ball valve (brass insert) for 25 mm outer dia pipe as per requirement of the site, complete all as specified and directed by Engr-in-charge. Make : SFMC/Prince or equivalent. |
| 60 | Supply and fixing in replacement of PP-R ball valve (brass insert) for 32 mm outer dia pipe as per requirement of the site, complete all as specified and directed by Engr-in-charge. . Make : SFMC/Prince or equivalent. |
| 61 | Supply and fix only 3 mm thick rubber inserting sheet make – Jyoti or equivalent, complete all as specified and directed by Engr-in-charge. |
| 62 | Supply and fix only 6 mm thick rubber inserting sheet make – Jyoti or equivalent, complete all as specified and directed by Engr-in-charge. |
| 63 | Supply and fix only galvanized steel nut-bolts, washers of any size, complete all as specified and directed by Engr-in-charge. |
| 64 | Supply and fix only ball bearing grease in 1 Kg packing make – Castrol / Veedol / HP, complete all as specified and directed by Engr-in-charge. |
| 65 | Supply and fix only cotton waste for water supply pump / sewage pump, complete all as specified and directed by Engr-in-charge. |
| 66 | Supply and fix only gland packing in stranded sealed packing ISI marked upto 20 mm size Make Turner or equivalent, complete all as specified and directed by Engr-in-charge. |
| 67 | M & L for rewinding of submersible motor 3 phase 10 HP cap with PVC insulated copper conductor cable of appropriate size alongwith necessary packing and winding material with and including taking out burnt winding , complete all as specified and directed by Engr-in-charge. |
| 68 | S & F as in replacement MCCB 160 Ampere,415 volts, 4 poles, breaking capacity 36 KA with adjustable thermal & magnetic release, complete all as specified and directed by Engr-in-charge. Make:- Legrand/C&S/Schneider |
| 69 | S & F as in replacement MCCB, 200 Ampere, 4 poles, 415 volts, breaking capacity 36 KA with adjustable thermal & magnetic release, complete all as specified and directed by Engr-in-charge. Make:- Legrand/C&S/Schneider |
| 70 | Earthing complete with galvanized steel earth plate electrodes 60x60x6 mm thick buried directly in ground earth (earth pit not less 2.25 m deep below ground level) with top edge of the plate not less then 1.5 mtr below normal ground level connected to galvanized iron earthing strip 32mm x6mm thick by means of bolt nuts check nuts and washers of galvnised iron or steel all as specified &shown in electrical plate No.3 of MES SSR part-I connected to earth test point as specified as specified and testing on completion including provision of 40 mm dia light grade pipe & watering pipe shall be 20 mm bore medium grade including all excavation & earth work in any type of soil incl PCC for pit (1:3:6) type C-1 with RCC cover in PCC(1:2:4) including charcoal , salt funnel GI pipe 40 mm dia light grade up to 7.5 mtr length, complete all as specified and directed by Engr-in-charge. |
| 71 | Excavation in trenches not exc 1.5 mtr wide & not exc 1.5 mtr in depth for foundation etc or for manholes, laying of pipe in soft / loose soil and getting out, complete all as specified and directed by Engr-in-charge. |
| 72 | Returning filling in, including spreading, leveling watering & well ramming in layers not exc 25cm thick, complete all as specified and directed by Engr-in-charge. |
| 73 | Removing excavated material to a distance not exc 50 mtr & depositing where directed at a level not exc 1.5 mtr above the starting point, complete all as specified and directed by Engr-in-charge. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 16, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 06, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 19 daysAug 08, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 21 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender