Tender For Provn Of Drying & Ironing Room Of Jcos /Or Families Lines B C , Dm Line & Dgo Line And Constr Of Candidates Waiting Area Shed At Hq Rtg Zone (Ne States) Shillong Under Ge Shillong
Tender Value
47.21 Lakhs
Estimated cost
Bid Submission
06 Aug 2026
10 days left
EMD
94420
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
East Khasi Hills → Meghalaya
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Provn Of Drying & Ironing Room Of Jcos /Or Families Lines B C , Dm Line & Dgo Line And Constr Of Candidates Waiting Area Shed At Hq Rtg Zone (Ne States) Shillong Under Ge Shillong
BOQ
| Sl. No. | Item Description |
| 1 | Surface excavation in soft/loose soil, not exceeding 30cm deep and averaging 15cm deep and getting out, complete all as specified and directed . |
| 2 | Excavating in post holes (or similar holes) each n exc 0.5 cum, getting out soft/loose soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm complete all as specified and directed. |
| 3 | M&L for PCC 1:4:8 Mix, type D-2 (using 40mm graded crushed stone aggregate) in foundation, filling and mass concrete complete all as specified and as directed. |
| 4 | M&L for Hard core, broken stone /boulders to gauge n exc 63 mm size , deposited , spread and levelled in layers n exc 15cm thick, watered and rammed to a true surface complete all as specified and directed. |
| 5 | M&L 100mm thick cement concrete 1:4:8 Mix, type D-2 ( using 40mm graded aggregate) as in sub base complete all as specified and directed. |
| 6 | M&L for PCC 1:2:4 Mix, type B-2 (using 40mm graded crushed stone aggregate) in foundation, filling and mass concrete icluding necessary form work, if required, complete all as specified and as directed. |
| 7 | M&L for providing coping, using cement concrete 1:2:4 Mix, Type B0 (using 12.5mm graded crushed stone aggregate) as in coping including necessary form work complete all as specified and directed. |
| 8 | M&L for Precast PCC 1:3:6 Mix, type C1 (using 20mm graded crushed stone aggregate) as in solid block masonry exc 10cm in width or girth and setting CM (1:6) complete all as specified and directed. |
| 9 | M&L for 25 mm thick PCC 1:2:4 Mix, type B0, using 12.5mm graded crushed stone aggregate, as in sub base finishing even and fair to receive floor finishes complete all as specified and directed. |
| 10 | M&L for non skid ceremic white tiles 7 to 8mm thick, area of each tile exc 0.18 sqm but n exc 0.38 sqm, as in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 15 mm thick cement screed bed in CM 1:6 complete all as specified and directed. |
| 11 | All as per Item No 10 above here–in–before but on vertical surfaces such as skirtings and risers to steps etc. over and including 10mm thick rendering in CM 1:4 as in backing coat complete all as specified and directed. |
| 12 | S&F steel work as in tubular , rafters, purlins, posts and similar work (round/square/rectangular shape of pipes as approved by Engr-in-charge ) trusses including posts, special shaped washers, gusset plates etc complete using ERW or induction butt welded tubes conformining to IS 1161-1998 garde St-240 complete all as specified and directed. |
| 13 | Supply and fixing Flush shutters, solid core construction 30 mm thick with block board core and plywood face panels, commercial type on both sides conforming to IS-2202(Part-I), 1983 complete all as specified and directed. |
| 14 | S&F steel window with side hung shutters including projection as box type hinges with steel handles and peg stay with glazing bars including one shop coat of red oxide primer complete all as specified and directed. |
| 15 | M&L for 4.80 mm thick sheet glass ordinary quality and glazing with oil putty area n.exc 0.50 sqm each pane complete all as specified and directed. |
| 16 | S&F butt hinges 75 mm medium weight, stainless steel, and fixed complete all as specified and directed. |
| 17 | S&F Butt hinges 125mm, medium weight, stainless steel, and fixed complete all as specified and directed. |
| 18 | S&F Mild steel barrel tower bolts of size 150 mm, stove enamelled black, with bright bolt and fixed complete all as specified and directed. |
| 19 | S&F Mild steel pressed handles, oval type, stove enamelled black of size 150 mm complete all as specified and directed. |
| 20 | S&F Mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed of size 300 mm long complete all as specified and directed. |
| 21 | M&L for Plates (plain or chequered) channels, angle , square cut or notched (ordinary and counter sunk) forming holes, without any attachment Fe 410 -W (Gde-E- 250) quality- A Fe complete all as specified and directed. |
| 22 | S & F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strenngth of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws including dismantling of old Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings complete all as specified and directed. |
| 23 | S & F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of an colour having tensile strenngth of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws including dismantling of Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings complete all as specified and directed. |
| 24 | M&L for 10 mm thick plaster in cm (1:6) on fair faces of brick or concrete surfaces including finishing even & smooth without using extra cement complete all as specified and directed. |
| 25 | M&L Rendering, 15 mm thick in CM 1:4, in two layers, first 5 mm thick with approved Water proofing compound @ 3% by the weight of cement or as per manufacturers instructions over a coat of 10 mm thick base coat finished even and smooth complete all as specified and directed .Note : WPC shall be measured and paid separately. |
| 26 | Supply only Integral waterproofing compound (Powder) complete all as specified and directed. |
| 27 | M&L for preparation of newely plastered /concrete surface of walls, and applying two coats of Oil Bound Distemper of approved shade/tint over a coat of compatiable priming paint complete all as specified and directed. |
| 28 | M&L for preparation of newely plastered/concrete surfaces of walls, priming with alkali resistant primer paint and applying two coats of weather coat exterior paint with roller etc complete all as specified and directed. |
| 29 | M&L for preparation of new or previously untreated surfaces of wood and wood based materials of any description not otherwise described, over 10 cm width or girth and applying two coats of Synthetic enamel paint over a coat of pink primer complete all as specified and directed. |
| 30 | M&L for 75 mm thick cement concrete 1:2:4, type B-2 (using 40mm graded agg) as in plinth protection finished even and smooth without using extra cement (incl necessary joint filling with mixture of paving bitumen & sand in 1:3) complete all as specified and directed. |
| 31 | M&L painting to new steel surfaces of any description, over 10cm in width or girth, and applying two coats of synthetic emamel paint over a coat of red-oxide primer complete all as specified and directed. |
| 32 | S&F Gl frame work for snapgrid false ceiling comprising of Gl perimeter channnel 0.55 mm thick with Main T- flange of 25 mm and web of 30 mm fixed to surrounding wall angle with flange and web 25 mm each , Cross T with flange 25 mm and web 25 mm fixed to main T, Main T is suspended from soffit @ 1200 mmm c/c using GI wire of 4mm thickness GI frame will be 60 x 60 cm to recieve E-board ceiling complete all as specified and directed . |
| 33 | M&L 4mm thick E Board 600x600 mm prepainted fibre boards ceiling designer/decorative type with different designs as approved by the Engr-in-charge fixed or laid in ceiling timber /GI/ aluminium frame work in ceiling flat or sloping complete all as per manufacturer instruction complete all as specified and directed. |
| 34 | S&F Hot Air Blower comprising factory-built electrically operated hot air blower complete with 15 KW, 415 Volts, 3 Phase electric tubular heating element assembly, centrifugal blower driven by 1.5 HP, 415 Volts, 3 Phase TEFC induction motor, capable of delivering not less than 800 CFM air at ambient temperature, complete with powder coated MS housing, inlet air filter, outlet duct connection, SSR (Solid State Relay) based automatic temperature control panel with digital temperature controller, contactor, MCB/MCCB, control transformer, indicating lamps, selector switches, over temperature cut-out, safety thermostat, overload protection and all internal wiring, mounted on suitable base frame, including supply and laying of 06 Nos. 10 Sqmm FRLS PVC insulated, unsheathed stranded copper conductor cable, 1100 Volts grade, conforming to IS 694, from existing main distribution board to control panel and from control panel to motor/heater assembly for a lead not exceeding 60 metres, complete with glands, lugs, cable saddles, ferrules, terminations, earthing connections and all accessories, complete in all respects and connected, tested and commissioned, all as specified and as directed.Make of Hot Air Blower: Thermotech Engineers / Tempsens Instruments / Jyoti Heat Energisers or equivalent approved. |
| 35 | S&F sensor for auto cut off to avoid high temperature in the drying room complete all as specified and directed. |
| 36 | S&F digital display thermometer with sensors fitted inside the room and display screen outside for display of information complete all as specified and directed. |
| 37 | S&F maintenance-free chemical earthing comprising copper bonded steel electrode of minimum 50 mm outside diameter and 2.0 metres long with minimum 250 microns copper bonding, driven/installed vertically in ground including excavation of earth in any type of soil (except rock) of required size and depth, providing factory manufactured conductive earthing enhancement backfill compound of not less than 25 kg around the electrode, watering arrangement consisting of 20 mm dia heavy duty PVC pipe with HDPE funnel and wire mesh, heavy duty brass/gun metal earth clamp, HDPE/polymer inspection chamber of suitable size with lockable cover, connection of earth conductor by suitable copper lugs, nuts, bolts and washers, refilling of excavated earth after proper compaction, removal and disposal of surplus excavated soil to a distance not exceeding 50 metres, complete with testing of earth resistance, commissioning and ensuring earth resistance not exceeding 2 Ohms (or as specified), complete in all respects conforming to IS 3043 (Latest Revision), all as specified and as directed. |
| 38 | M&L for PCC (1:3:6), type C2 using 40 mm graded crushed stone aggregate as in foundation, filling and mass concrete complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 16, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 06, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 10 daysAug 07, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 11 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender