Tender For Deposit-Tmc - Providing Online Booster Pump Sets-Near Pullannivila -Moonnumukk, Nalumukk Area-Chanthavila Ward-General Civil Work
Tender Value
3.54 Lakhs
Estimated cost
Bid Submission
24 Jul 2026
1 days left
EMD
8853
Bank guarantee accepted
Document Fee
785
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Thiruvananthapuram → Kerala
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Deposit-Tmc - Providing Online Booster Pump Sets-Near Pullannivila -Moonnumukk, Nalumukk Area-Chanthavila Ward-General Civil Work
BOQ
| Sl. No. | Item Description |
| 1 | Supplying, Installation and commissioning of Online pressure Boosting system |
| 2 | OD1951/2026-2027:Supply and Installation of variable head (18-29m) centrifugal type booster pump, 3 phase,50 Hz. with a Discharge range of 15- 28 LPS with size of 100mm x 100mm suitable for the location. The rate is including, cost of pump, cost of motor, cost of approved panel board, cost of starter, Aluminium cable from panel board to starter and starter to Motor, cost of Capacitor, necessary suction pipe, foot valve, Non return Valve and necessary PVC valves, suitable Earthing as per IE rule, Erection charges including foundation, base plate, cost of cement sand and metal, trail run and commissioning etc. complete as per the direction of Engineer In Charge. Along with onsite Warranty for at least 1 Year. The Actual Head and Power Requirement will be decided by Contractor on actual field study report. |
| 3 | OD1952/2026-2027:Installation of Shelter for pump and fittings using 12mm Cement boards for a shelter having length of 6 feet, width of 4 feet and height of 6 feet. Required Structural support to be done by Square tubes for installation of cement boards as side walls and roof, Supplying and installation of shingles roofing as per the direction of the departmental officers. Including cost of materials, welding charges, labour charges etc complete. |
| 4 | OD1957/2026-2027:Automation of Pump by supplying and installing Universal automatic panel, Dry run preventer, Overload protection, Low/High voltage protection, Phase preventer, Timer unit, Pressure Switch etc. As Directed by The Engineer In Charge. Along with Onsite Warranty of at least 1 Year |
| 5 | OD1955/2026-2027:Supply and Installation of Pressure tank of 25L capacity with all fittings |
| 6 | OD1949/2026-2027:Cost for Engaging Wire man and helper for taking 3 phase electric connection from KSEB by installation of necessary switches, laying of cables, fixing of safety devices, providing provision for earthing, providing fuse etc. as per the statutory requirements. |
| 7 | OD1950/2026-2027:Providing and fixing in position industrial-type pressure gauges with gunmetal/brass valves in pipe lines including all specials etc complete |
| 8 | 15.2.2:Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in-Charge.Nominal concrete 1:4:8 or leaner mix ( including equivalent design mix) |
| 9 | 15.43.2:Dismantling manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer -in-Charge:Bituminous road |
| 10 | 100.1.1:Excavating trenches of required width for pipes, cables, etc., including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20cm in depth, including consolidating each deposited layer by ramming, watering, etc., and disposing of surplus excavated soil as directed, within a lead of 50m, in all kinds of soil. |
| 11 | 100.9.9:Laying uPVC pipes of class 2 to class 6 and specials, lowering to the trenches already made, placing in position aligning the pipeline to the lines and levels and jointing the pipes and specials with solvent cement and testing the pipeline with water to the required test pressure (excluding cost of pipes and specials): 110 mm nominal outside diameter pipes. |
| 12 | 100.98.214:Supply of PVC Pipe, 6kg/cm2, 110mm Dia. |
| 13 | OD1958/2026-2027:Providing and fixing 110mm PVC ball valve with all accessories in existing line as per direction of Engineer In Charge |
| 14 | OD1953/2026-2027:Supply and Installation of 100mm NRV in pipe lines as per site requirement |
| 15 | OD1956/2026-2027:Supply of 110mm pvc 90 degree bend |
| 16 | OD1959/2026-2027:Supply of 110mmx110mm PVC Tee |
| 17 | 100.98.1008:Engaging Coolie. |
| 18 | 100.98.1009:Engaging Fitter ( grade 1). |
| 19 | OD1960/2026-2027:Labelling and sticker works for the pump house as per the direction of Departmental officers |
| 20 | 13.50.3:Applying priming coat:With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron /steel works |
| 21 | 13.80:Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 22 | 13.60.1:Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade:Two or more coats on new work |
| 23 | 13.53.1:Painting on G.S. sheet with synthetic enamel paint of approved brand and manufacture of required colour to given an even shade:New work (two or more coats) including coat of approved steel primer but excluding a coat of mordant solution. |
| 24 | 4.1.4:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 gradedstone aggregate 40 mm nominal size derived from natural sources) |
| 25 | 100.37.5.1:In situ fabrication of M.S. pipes of size 100mm (I.D.) using 8mm thick M.S. plate including cost and conveyance charges of M.S. plate, all fabrication charges, charges of painting the steel work with two or more coat deluxe multi surface paint to give an even shade over an under-coat of primer etc., complete. |
| 26 | 100.37.5.2:Fabricating M.S. flanges of diameter 100mm using 12mm thick M.S. plate including cost and conveyance charges of M.S. plate, all fabrication charges, charges of painting the steel work with two or more coat deluxe multi surface paint to give an even shade over an under-coat of primer etc., complete: For pipes fabricated with 8mm thick M.S. plates. |
| 27 | 100.37.5.3:Cutting 100mm (I.D.) M.S. pipes for making bends and other specials by gas cutting including cost of gas, all labour and hire charges of tools etc., complete: For pipes fabricated with 8mm thick M.S. plates. |
| 28 | 100.37.5.4:Welding 100mm (I.D.) M.S. pipes for making bends and other specials by gas/electric welding machine including cost of gas and welding rods, all labour and hire charges of tools etc., complete: For pipes fabricated with 8mm thick M.S. plates. |
| 29 | 100.37.5.5:Grinding cut and weld edges of 100mm (I.D.) M.S. pipes during fabrication work including all labour and hire charges of tools etc., complete: For pipes fabricated with 8mm thick M.S. plates. |
| 30 | 100.37.7.1:In situ fabrication of M.S. pipes of size 200mm (I.D.) using 8mm thick M.S. plate including cost and conveyance charges of M.S. plate, all fabrication charges, charges of painting the steel work with two or more coat deluxe multi surface paint to give an even shade over an under-coat of primer etc., complete. |
| 31 | 100.37.7.2:Fabricating M.S. flanges of diameter 200mm using 12mm thick M.S. plate including cost and conveyance charges of M.S. plate, all fabrication charges, charges of painting the steel work with two or more coat deluxe multi surface paint to give an even shade over an under-coat of primer etc., complete: For pipes fabricated with 8mm thick M.S. plates. |
| 32 | 100.37.7.3:Cutting 200mm (I.D.) M.S. pipes for making bends and other specials by gas cutting including cost of gas, all labour and hire charges of tools etc., complete: For pipes fabricated with 8mm thick M.S. plates. |
| 33 | 100.37.7.4:Welding 200mm (I.D.) M.S. pipes for making bends and other specials by gas/electric welding machine including cost of gas and welding rods, all labour and hire charges of tools etc., complete: For pipes fabricated with 8mm thick M.S. plates. |
| 34 | 100.37.7.5:Grinding cut and weld edges of 200mm (I.D.) M.S. pipes during fabrication work including all labour and hire charges of tools etc., complete: For pipes fabricated with 8mm thick M.S. plates. |
| 35 | OD1954/2026-2027:Providing and fixing in position industrial type pressure gauges with gun metal/brass valves in pipe lines including all specials etc complete |
| 36 | Providing Valve Chamber |
| 37 | 2.6.1:Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.All kinds of soil |
| 38 | 4.1.8:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 39 | 5.22.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more |
| 40 | 5.1.2:Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 41 | 4.3.2:Centering and shuttering including strutting, propping etc. and removal of form work for:Retaining walls, return walls, (any thickness) including attached pilasters, buttresses, plinth and string courses fillets, kerbs and steps etc. |
| 42 | 13.1.1:12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand) |
| 43 | OD1961/2026-2027:Supplying CI MH cover with frame (heavy duty Type) Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 16, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 24, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 1 dayJul 25, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 2 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender